diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
8 files changed, 145 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt index 6c396f17c91a..816b244a221e 100644 --- a/Documentation/devicetree/bindings/pci/altera-pcie.txt +++ b/Documentation/devicetree/bindings/pci/altera-pcie.txt @@ -1,11 +1,13 @@ * Altera PCIe controller Required properties: -- compatible : should contain "altr,pcie-root-port-1.0" +- compatible : should contain "altr,pcie-root-port-1.0" or "altr,pcie-root-port-2.0" - reg: a list of physical base address and length for TXS and CRA. + For "altr,pcie-root-port-2.0", additional HIP base address and length. - reg-names: must include the following entries: "Txs": TX slave port region "Cra": Control register access region + "Hip": Hard IP region (if "altr,pcie-root-port-2.0") - interrupts: specifies the interrupt source of the parent interrupt controller. The format of the interrupt specifier depends on the parent interrupt controller. diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index c124f9bc11f3..5561a1c060d0 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -4,8 +4,11 @@ Required properties: - compatible: "snps,dw-pcie" for RC mode; "snps,dw-pcie-ep" for EP mode; -- reg: Should contain the configuration address space. -- reg-names: Must be "config" for the PCIe configuration space. +- reg: For designware cores version < 4.80 contains the configuration + address space. For designware core version >= 4.80, contains + the configuration and ATU address space +- reg-names: Must be "config" for the PCIe configuration space and "atu" for + the ATU address space. (The old way of getting the configuration address space from "ranges" is deprecated and should be avoided.) - num-lanes: number of lanes to use diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index d514c1f2365f..a7f5f5afa0e6 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -9,6 +9,7 @@ Required properties: - "fsl,imx6sx-pcie", - "fsl,imx6qp-pcie" - "fsl,imx7d-pcie" + - "fsl,imx8mq-pcie" - reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. @@ -45,7 +46,7 @@ Additional required properties for imx6sx-pcie: PCIE_PHY power domains - power-domain-names: Must be "pcie", "pcie_phy" -Additional required properties for imx7d-pcie: +Additional required properties for imx7d-pcie and imx8mq-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain - resets: Must contain phandles to PCIe-related reset lines exposed by SRC IP block @@ -53,6 +54,11 @@ Additional required properties for imx7d-pcie: - "pciephy" - "apps" - "turnoff" +- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node. + +Additional required properties for imx8mq-pcie: +- clock-names: Must include the following additional entries: + - "pcie_aux" Example: @@ -79,3 +85,13 @@ Example: clocks = <&clks 144>, <&clks 206>, <&clks 189>; clock-names = "pcie", "pcie_bus", "pcie_phy"; }; + +* Freescale i.MX7d PCIe PHY + +This is the PHY associated with the IMX7d PCIe controller. It's used by the +PCI-e controller via the fsl,imx7d-pcie-phy phandle. + +Required properties: +- compatible: + - "fsl,imx7d-pcie-phy" +- reg: base address and length of the PCIe PHY controller diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index 9b2b8d66d1f4..e20ceaab9b38 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -13,6 +13,7 @@ information. Required properties: - compatible: should contain the platform identifier such as: + RC mode: "fsl,ls1021a-pcie" "fsl,ls2080a-pcie", "fsl,ls2085a-pcie" "fsl,ls2088a-pcie" @@ -20,6 +21,8 @@ Required properties: "fsl,ls1046a-pcie" "fsl,ls1043a-pcie" "fsl,ls1012a-pcie" + EP mode: + "fsl,ls1046a-pcie-ep", "fsl,ls-pcie-ep" - reg: base addresses and lengths of the PCIe controller register blocks. - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 2030ee0dc4f9..47202a2938f2 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -11,16 +11,24 @@ described here as well as properties that are not applicable. Required Properties:- -compatibility: "ti,keystone-pcie" -reg: index 1 is the base address and length of DW application registers. - index 2 is the base address and length of PCI device ID register. +compatibility: Should be "ti,keystone-pcie" for RC on Keystone2 SoC + Should be "ti,am654-pcie-rc" for RC on AM654x SoC +reg: Three register ranges as listed in the reg-names property +reg-names: "dbics" for the DesignWare PCIe registers, "app" for the + TI specific application registers, "config" for the + configuration space address pcie_msi_intc : Interrupt controller device node for MSI IRQ chip interrupt-cells: should be set to 1 interrupts: GIC interrupt lines connected to PCI MSI interrupt lines + (required if the compatible is "ti,keystone-pcie") +msi-map: As specified in Documentation/devicetree/bindings/pci/pci-msi.txt + (required if the compatible is "ti,am654-pcie-rc". ti,syscon-pcie-id : phandle to the device control module required to set device id and vendor id. +ti,syscon-pcie-mode : phandle to the device control module required to configure + PCI in either RC mode or EP mode. Example: pcie_msi_intc: msi-interrupt-controller { @@ -61,3 +69,47 @@ Optional properties:- DesignWare DT Properties not applicable for Keystone PCI 1. pcie_bus clock-names not used. Instead, a phandle to phys is used. + +AM654 PCIe Endpoint +=================== + +Required Properties:- + +compatibility: Should be "ti,am654-pcie-ep" for EP on AM654x SoC +reg: Four register ranges as listed in the reg-names property +reg-names: "dbics" for the DesignWare PCIe registers, "app" for the + TI specific application registers, "atu" for the + Address Translation Unit configuration registers and + "addr_space" used to map remote RC address space +num-ib-windows: As specified in + Documentation/devicetree/bindings/pci/designware-pcie.txt +num-ob-windows: As specified in + Documentation/devicetree/bindings/pci/designware-pcie.txt +num-lanes: As specified in + Documentation/devicetree/bindings/pci/designware-pcie.txt +power-domains: As documented by the generic PM domain bindings in + Documentation/devicetree/bindings/power/power_domain.txt. +ti,syscon-pcie-mode: phandle to the device control module required to configure + PCI in either RC mode or EP mode. + +Optional properties:- + +phys: list of PHY specifiers (used by generic PHY framework) +phy-names: must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of lanes as specified in *num-lanes* property. +("phys" and "phy-names" DT bindings are specified in +Documentation/devicetree/bindings/phy/phy-bindings.txt) +interrupts: platform interrupt for error interrupts. + +pcie-ep { + compatible = "ti,am654-pcie-ep"; + reg = <0x5500000 0x1000>, <0x5501000 0x1000>, + <0x10000000 0x8000000>, <0x5506000 0x1000>; + reg-names = "app", "dbics", "addr_space", "atu"; + power-domains = <&k3_pds 120>; + ti,syscon-pcie-mode = <&pcie0_mode>; + num-lanes = <1>; + num-ib-windows = <16>; + num-ob-windows = <16>; + interrupts = <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index c77981c5dd18..92c01db610df 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -24,3 +24,53 @@ driver implementation may support the following properties: unsupported link speed, for instance, trying to do training for unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' for gen2, and '1' for gen1. Any other values are invalid. + +PCI-PCI Bridge properties +------------------------- + +PCIe root ports and switch ports may be described explicitly in the device +tree, as children of the host bridge node. Even though those devices are +discoverable by probing, it might be necessary to describe properties that +aren't provided by standard PCIe capabilities. + +Required properties: + +- reg: + Identifies the PCI-PCI bridge. As defined in the IEEE Std 1275-1994 + document, it is a five-cell address encoded as (phys.hi phys.mid + phys.lo size.hi size.lo). phys.hi should contain the device's BDF as + 0b00000000 bbbbbbbb dddddfff 00000000. The other cells should be zero. + + The bus number is defined by firmware, through the standard bridge + configuration mechanism. If this port is a switch port, then firmware + allocates the bus number and writes it into the Secondary Bus Number + register of the bridge directly above this port. Otherwise, the bus + number of a root port is the first number in the bus-range property, + defaulting to zero. + + If firmware leaves the ARI Forwarding Enable bit set in the bridge + above this port, then phys.hi contains the 8-bit function number as + 0b00000000 bbbbbbbb ffffffff 00000000. Note that the PCIe specification + recommends that firmware only leaves ARI enabled when it knows that the + OS is ARI-aware. + +Optional properties: + +- external-facing: + When present, the port is external-facing. All bridges and endpoints + downstream of this port are external to the machine. The OS can, for + example, use this information to identify devices that cannot be + trusted with relaxed DMA protection, as users could easily attach + malicious devices to this port. + +Example: + +pcie@10000000 { + compatible = "pci-host-ecam-generic"; + ... + pcie@0008 { + /* Root port 00:01.0 is external-facing */ + reg = <0x00000800 0 0 0 0>; + external-facing; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 976ef7bfff93..6904882a0e94 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -3,6 +3,7 @@ Required properties: compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a7744" for the R8A7744 SoC; + "renesas,pcie-r8a774c0" for the R8A774C0 SoC; "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; @@ -13,7 +14,8 @@ compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a77990" for the R8A77990 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or RZ/G1 compatible device. - "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. + "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 or + RZ/G2 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 452fe48c4fdd..d5cbfe6b0d89 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -1,14 +1,21 @@ TI PCI Controllers PCIe DesignWare Controller - - compatible: Should be "ti,dra7-pcie" for RC - Should be "ti,dra7-pcie-ep" for EP + - compatible: Should be "ti,dra7-pcie" for RC (deprecated) + Should be "ti,dra7-pcie-ep" for EP (deprecated) + Should be "ti,dra746-pcie-rc" for dra74x/dra76 in RC mode + Should be "ti,dra746-pcie-ep" for dra74x/dra76 in EP mode + Should be "ti,dra726-pcie-rc" for dra72x in RC mode + Should be "ti,dra726-pcie-ep" for dra72x in EP mode - phys : list of PHY specifiers (used by generic PHY framework) - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the number of PHYs as specified in *phys* property. - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", where <X> is the instance number of the pcie from the HW spec. - num-lanes as specified in ../designware-pcie.txt + - ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control + module and the register offset to specify lane + selection. HOST MODE ========= |