diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 120 |
1 files changed, 120 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml new file mode 100644 index 000000000000..58f0cea160ef --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml @@ -0,0 +1,120 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/jedec,spi-nor.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI NOR flash ST M25Pxx (and similar) serial flash chips + +maintainers: + - Rob Herring <robh@kernel.org> + +allOf: + - $ref: mtd.yaml# + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + oneOf: + - items: + - pattern: "^((((micron|spansion|st),)?\ + (m25p(40|80|16|32|64|128)|\ + n25q(32b|064|128a11|128a13|256a|512a|164k)))|\ + atmel,at25df(321a|641|081a)|\ + everspin,mr25h(10|40|128|256)|\ + (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\ + (mxicy|macronix),mx25u(4033|4035)|\ + (spansion,)?s25fl(128s|256s1|512s|008k|064k|164k)|\ + (sst|microchip),sst25vf(016b|032b|040b)|\ + (sst,)?sst26wf016b|\ + (sst,)?sst25wf(040b|080)|\ + winbond,w25x(80|32)|\ + (winbond,)?w25q(16|32(w|dw)?|64(dw)?|80bl|128(fw)?|256))$" + - const: jedec,spi-nor + - items: + - enum: + - issi,is25lp016d + - micron,mt25qu02g + - mxicy,mx25r1635f + - mxicy,mx25u6435f + - mxicy,mx25v8035f + - spansion,s25sl12801 + - spansion,s25fs512s + - const: jedec,spi-nor + - const: jedec,spi-nor + description: + SPI NOR flashes compatible with the JEDEC SFDP standard or which may be + identified with the READ ID opcode (0x9F) do not deserve a specific + compatible. They should instead only be matched against the generic + "jedec,spi-nor" compatible. + + reg: + minItems: 1 + maxItems: 2 + + m25p,fast-read: + type: boolean + description: + Use the "fast read" opcode to read data from the chip instead of the usual + "read" opcode. This opcode is not supported by all chips and support for + it can not be detected at runtime. Refer to your chips' datasheet to check + if this is supported by your chip. + + broken-flash-reset: + type: boolean + description: + Some flash devices utilize stateful addressing modes (e.g., for 32-bit + addressing) which need to be managed carefully by a system. Because these + sorts of flash don't have a standardized software reset command, and + because some systems don't toggle the flash RESET# pin upon system reset + (if the pin even exists at all), there are systems which cannot reboot + properly if the flash is left in the "wrong" state. This boolean flag can + be used on such systems, to denote the absence of a reliable reset + mechanism. + + no-wp: + type: boolean + description: + The status register write disable (SRWD) bit in status register, combined + with the WP# signal, provides hardware data protection for the device. When + the SRWD bit is set to 1, and the WP# signal is either driven LOW or hard + strapped to LOW, the status register nonvolatile bits become read-only and + the WRITE STATUS REGISTER operation will not execute. The only way to exit + this hardware-protected mode is to drive WP# HIGH. If the WP# signal of the + flash device is not connected or is wrongly tied to GND (that includes internal + pull-downs) then status register permanently becomes read-only as the SRWD bit + cannot be reset. This boolean flag can be used on such systems to avoid setting + the SRWD bit while writing the status register. WP# signal hard strapped to GND + can be a valid use case. + + reset-gpios: + description: + A GPIO line connected to the RESET (active low) signal of the device. + If "broken-flash-reset" is present then having this property does not + make any difference. + + spi-cpol: true + spi-cpha: true + +dependencies: + spi-cpol: [ spi-cpha ] + spi-cpha: [ spi-cpol ] + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + flash@0 { + compatible = "spansion,m25p80", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + m25p,fast-read; + reset-gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + }; +... |