diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc/mmc-controller.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/mmc-controller.yaml | 57 |
1 files changed, 25 insertions, 32 deletions
diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml index 186f04ba9357..58ae298cd2fc 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml +++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/mmc/mmc-controller.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: MMC Controller Generic Binding +title: MMC Controller Common Properties maintainers: - Ulf Hansson <ulf.hansson@linaro.org> @@ -40,6 +40,7 @@ properties: There is no card detection available; polling must be used. cd-gpios: + maxItems: 1 description: The card detection will be done using the GPIO provided. @@ -87,11 +88,18 @@ properties: default: 1 max-frequency: - description: - Maximum operating frequency of the bus. + description: | + Maximum operating frequency of the bus: + - for eMMC, the maximum supported frequency is 200MHz, + - for SD/SDIO cards the SDR104 mode has a max supported + frequency of 208MHz, + - some mmc host controllers do support a max frequency upto + 384MHz. + So, lets keep the maximum supported value here. + $ref: /schemas/types.yaml#/definitions/uint32 minimum: 400000 - maximum: 200000000 + maximum: 384000000 disable-wp: $ref: /schemas/types.yaml#/definitions/flag @@ -104,6 +112,7 @@ properties: line. Not used in combination with eMMC or SDIO. wp-gpios: + maxItems: 1 description: GPIO to use for the write-protect detection. @@ -218,6 +227,11 @@ properties: description: eMMC HS400 enhanced strobe mode is supported + no-mmc-hs400: + $ref: /schemas/types.yaml#/definitions/flag + description: + All eMMC HS400 modes are not supported. + dsr: description: Value the card Driver Stage Register (DSR) should be programmed @@ -255,11 +269,10 @@ properties: post-power-on-delay-ms: description: It was invented for MMC pwrseq-simple which could be referred to - mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay + mmc-pwrseq-simple.yaml. But now it\'s reused as a tunable delay waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. - $ref: /schemas/types.yaml#/definitions/uint32 default: 10 supports-cqe: @@ -280,7 +293,6 @@ properties: description: SDIO only. Preserves card power during a suspend/resume cycle. - # Deprecated: enable-sdio-wakeup wakeup-source: $ref: /schemas/types.yaml#/definitions/flag description: @@ -292,7 +304,10 @@ properties: vqmmc-supply: description: - Supply for the bus IO line power + Supply for the bus IO line power, such as a level shifter. + If the level shifter is controlled by a GPIO line, this shall + be modeled as a "regulator-fixed" with a GPIO line for + switching the level shifter on/off. mmc-pwrseq: $ref: /schemas/types.yaml#/definitions/phandle @@ -327,12 +342,6 @@ patternProperties: subnode describes. A value of 0 denotes the memory SD function, values from 1 to 7 denote the SDIO functions. - broken-hpi: - $ref: /schemas/types.yaml#/definitions/flag - description: - Use this to indicate that the mmc-card has a broken hpi - implementation, and that hpi should not be used. - required: - reg @@ -357,22 +366,6 @@ additionalProperties: true examples: - | - mmc@ab000000 { - compatible = "sdhci"; - reg = <0xab000000 0x200>; - interrupts = <23>; - bus-width = <4>; - cd-gpios = <&gpio 69 0>; - cd-inverted; - wp-gpios = <&gpio 70 0>; - max-frequency = <50000000>; - keep-power-in-suspend; - wakeup-source; - mmc-pwrseq = <&sdhci0_pwrseq>; - clk-phase-sd-hs = <63>, <72>; - }; - - - | mmc3: mmc@1c12000 { #address-cells = <1>; #size-cells = <0>; @@ -384,9 +377,9 @@ examples: non-removable; mmc-pwrseq = <&sdhci0_pwrseq>; - brcmf: bcrmf@1 { + brcmf: wifi@1 { reg = <1>; - compatible = "brcm,bcm43xx-fmac"; + compatible = "brcm,bcm4329-fmac"; interrupt-parent = <&pio>; interrupts = <10 8>; interrupt-names = "host-wake"; |