diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media')
18 files changed, 394 insertions, 19 deletions
diff --git a/Documentation/devicetree/bindings/media/aspeed-video.txt b/Documentation/devicetree/bindings/media/aspeed-video.txt index 78b464ae2672..ce2894506e1f 100644 --- a/Documentation/devicetree/bindings/media/aspeed-video.txt +++ b/Documentation/devicetree/bindings/media/aspeed-video.txt @@ -14,6 +14,11 @@ Required properties: the VE - interrupts: the interrupt associated with the VE on this platform +Optional properties: + - memory-region: + phandle to a memory region to allocate from, as defined in + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt + Example: video-engine@1e700000 { @@ -23,4 +28,5 @@ video-engine@1e700000 { clock-names = "vclk", "eclk"; resets = <&syscon ASPEED_RESET_VIDEO>; interrupts = <7>; + memory-region = <&video_engine_memory>; }; diff --git a/Documentation/devicetree/bindings/media/cedrus.txt b/Documentation/devicetree/bindings/media/cedrus.txt index bce0705df953..20c82fb0c343 100644 --- a/Documentation/devicetree/bindings/media/cedrus.txt +++ b/Documentation/devicetree/bindings/media/cedrus.txt @@ -13,6 +13,7 @@ Required properties: - "allwinner,sun8i-h3-video-engine" - "allwinner,sun50i-a64-video-engine" - "allwinner,sun50i-h5-video-engine" + - "allwinner,sun50i-h6-video-engine" - reg : register base and length of VE; - clocks : list of clock specifiers, corresponding to entries in the clock-names property; diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt index 5dddc95f9cc4..4f91686e54a6 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv748x.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -48,7 +48,16 @@ are numbered as follows. TXA source 10 TXB source 11 -The digital output port nodes must contain at least one endpoint. +The digital output port nodes, when present, shall contain at least one +endpoint. Each of those endpoints shall contain the data-lanes property as +described in video-interfaces.txt. + +Required source endpoint properties: + - data-lanes: an array of physical data lane indexes + The accepted value(s) for this property depends on which of the two + sources are described. For TXA 1, 2 or 4 data lanes can be described + while for TXB only 1 data lane is valid. See video-interfaces.txt + for detailed description. Ports are optional if they are not connected to anything at the hardware level. diff --git a/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt new file mode 100644 index 000000000000..060d2b7a5893 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt @@ -0,0 +1,20 @@ +* Melexis MLX90640 FIR Sensor + +Melexis MLX90640 FIR sensor support which allows recording of thermal data +with 32x24 resolution excluding 2 lines of coefficient data that is used by +userspace to render processed frames. + +Required Properties: + - compatible : Must be "melexis,mlx90640" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + mlx90640@33 { + compatible = "melexis,mlx90640"; + reg = <0x33>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m001.txt b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt new file mode 100644 index 000000000000..c920552b03ef --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt @@ -0,0 +1,38 @@ +MT9M001: 1/2-Inch Megapixel Digital Image Sensor + +The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital +image sensor. It is programmable through I2C interface. + +Required Properties: + +- compatible: shall be "onnn,mt9m001". +- clocks: reference to the master clock into sensor + +Optional Properties: + +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. + Active low. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. + Active high. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + &i2c1 { + camera-sensor@5d { + compatible = "onnn,mt9m001"; + reg = <0x5d>; + reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + clocks = <&camera_clk>; + port { + mt9m001_out: endpoint { + remote-endpoint = <&vcap_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt index fd7aec9f8e24..72ad992f77be 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt @@ -26,9 +26,9 @@ Example: &i2c1 { ... - ov5645: ov5645@78 { + ov5645: ov5645@3c { compatible = "ovti,ov5645"; - reg = <0x78>; + reg = <0x3c>; enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; @@ -37,7 +37,7 @@ Example: clocks = <&clks 200>; clock-names = "xclk"; - clock-frequency = <23880000>; + clock-frequency = <24000000>; vdddo-supply = <&camera_dovdd_1v8>; vdda-supply = <&camera_avdd_2v8>; diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt new file mode 100644 index 000000000000..7976e6c40a80 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt @@ -0,0 +1,82 @@ +STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge + +MIPID02 has two CSI-2 input ports, only one of those ports can be active at a +time. Active port input stream will be de-serialized and its content outputted +through PARALLEL output port. +CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second +input port is a single lane 800Mbps. Both ports support clock and data lane +polarity swap. First port also supports data lane swap. +PARALLEL output port has a maximum width of 12 bits. +Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444, +YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. + +Required Properties: +- compatible: shall be "st,st-mipid02" +- clocks: reference to the xclk input clock. +- clock-names: shall be "xclk". +- VDDE-supply: sensor digital IO supply. Must be 1.8 volts. +- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the xsdn pin, if any. + This is an active low signal to the mipid02. + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes are numbered as follows: + + Port Description + ----------------------------- + 0 CSI-2 first input port + 1 CSI-2 second input port + 2 PARALLEL output + +Endpoint node required property for CSI-2 connection is: +- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be +<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>. +Endpoint node optional property for CSI-2 connection is: +- lane-polarities: any lane can be inverted or not. + +Endpoint node required property for PARALLEL connection is: +- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>. +Endpoint node optional properties for PARALLEL connection are: +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +LOW being the default. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +LOW being the default. + +Example: + +mipid02: csi2rx@14 { + compatible = "st,st-mipid02"; + reg = <0x14>; + status = "okay"; + clocks = <&clk_ext_camera_12>; + clock-names = "xclk"; + VDDE-supply = <&vdd>; + VDDIN-supply = <&vdd>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + ep0: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&mipi_csi2_in>; + }; + }; + port@2 { + reg = <2>; + + ep2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + remote-endpoint = <¶llel_out>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/imx7-csi.txt b/Documentation/devicetree/bindings/media/imx7-csi.txt new file mode 100644 index 000000000000..3c07bc676bc3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx7-csi.txt @@ -0,0 +1,45 @@ +Freescale i.MX7 CMOS Sensor Interface +===================================== + +csi node +-------- + +This is device node for the CMOS Sensor Interface (CSI) which enables the chip +to connect directly to external CMOS image sensors. + +Required properties: + +- compatible : "fsl,imx7-csi"; +- reg : base address and length of the register set for the device; +- interrupts : should contain CSI interrupt; +- clocks : list of clock specifiers, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details; +- clock-names : must contain "axi", "mclk" and "dcic" entries, matching + entries in the clock property; + +The device node shall contain one 'port' child node with one child 'endpoint' +node, according to the bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt. + +In the following example a remote endpoint is a video multiplexer. + +example: + + csi: csi@30710000 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "fsl,imx7-csi"; + reg = <0x30710000 0x10000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CSI_MCLK_ROOT_CLK>, + <&clks IMX7D_CLK_DUMMY>; + clock-names = "axi", "mclk", "dcic"; + + port { + csi_from_csi_mux: endpoint { + remote-endpoint = <&csi_mux_to_csi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt new file mode 100644 index 000000000000..71fd74ed3ec8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt @@ -0,0 +1,90 @@ +Freescale i.MX7 Mipi CSI2 +========================= + +mipi_csi2 node +-------------- + +This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is +compatible with previous version of Samsung D-phy. + +Required properties: + +- compatible : "fsl,imx7-mipi-csi2"; +- reg : base address and length of the register set for the device; +- interrupts : should contain MIPI CSIS interrupt; +- clocks : list of clock specifiers, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details; +- clock-names : must contain "pclk", "wrap" and "phy" entries, matching + entries in the clock property; +- power-domains : a phandle to the power domain, see + Documentation/devicetree/bindings/power/power_domain.txt for details. +- reset-names : should include following entry "mrst"; +- resets : a list of phandle, should contain reset entry of + reset-names; +- phy-supply : from the generic phy bindings, a phandle to a regulator that + provides power to MIPI CSIS core; + +Optional properties: + +- clock-frequency : The IP's main (system bus) clock frequency in Hz, default + value when this property is not specified is 166 MHz; +- fsl,csis-hs-settle : differential receiver (HS-RX) settle time; + +The device node should contain two 'port' child nodes with one child 'endpoint' +node, according to the bindings defined in: + Documentation/devicetree/bindings/ media/video-interfaces.txt. + The following are properties specific to those nodes. + +port node +--------- + +- reg : (required) can take the values 0 or 1, where 0 shall be + related to the sink port and port 1 shall be the source + one; + +endpoint node +------------- + +- data-lanes : (required) an array specifying active physical MIPI-CSI2 + data input lanes and their mapping to logical lanes; this + shall only be applied to port 0 (sink port), the array's + content is unused only its length is meaningful, + in this case the maximum length supported is 2; + +example: + + mipi_csi: mipi-csi@30750000 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "fsl,imx7-mipi-csi2"; + reg = <0x30750000 0x10000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_IPG_ROOT_CLK>, + <&clks IMX7D_MIPI_CSI_ROOT_CLK>, + <&clks IMX7D_MIPI_DPHY_ROOT_CLK>; + clock-names = "pclk", "wrap", "phy"; + clock-frequency = <166000000>; + power-domains = <&pgc_mipi_phy>; + phy-supply = <®_1p0d>; + resets = <&src IMX7_RESET_MIPI_PHY_MRST>; + reset-names = "mrst"; + fsl,csis-hs-settle = <3>; + + port@0 { + reg = <0>; + + mipi_from_sensor: endpoint { + remote-endpoint = <&ov2680_to_mipi>; + data-lanes = <1>; + }; + }; + + port@1 { + reg = <1>; + + mipi_vc0_to_csi_mux: endpoint { + remote-endpoint = <&csi_mux_from_mipi_vc0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt index 2a615d84a682..b6b5dde6abd8 100644 --- a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -66,6 +66,15 @@ vcodec_dec: vcodec@16000000 { "vencpll", "venc_lt_sel", "vdec_bus_clk_src"; + assigned-clocks = <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>; + assigned-clock-parents = <&topckgen CLK_TOP_VCODECPLL_370P5>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_VCODECPLL>; + assigned-clock-rates = <0>, <0>, <0>, <1482000000>, <800000000>; }; vcodec_enc: vcodec@18002000 { @@ -105,4 +114,8 @@ vcodec_dec: vcodec@16000000 { "venc_sel", "venc_lt_sel_src", "venc_lt_sel"; + assigned-clocks = <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_VENCPLL_D2>, + <&topckgen CLK_TOP_UNIVPLL1_D2>; }; diff --git a/Documentation/devicetree/bindings/media/meson-ao-cec.txt b/Documentation/devicetree/bindings/media/meson-ao-cec.txt index 8671bdb08080..c67fc41d4aa2 100644 --- a/Documentation/devicetree/bindings/media/meson-ao-cec.txt +++ b/Documentation/devicetree/bindings/media/meson-ao-cec.txt @@ -4,16 +4,23 @@ The Amlogic Meson AO-CEC module is present is Amlogic SoCs and its purpose is to handle communication between HDMI connected devices over the CEC bus. Required properties: - - compatible : value should be following + - compatible : value should be following depending on the SoC : + For GXBB, GXL, GXM and G12A (AO_CEC_A module) : "amlogic,meson-gx-ao-cec" + For G12A (AO_CEC_B module) : + "amlogic,meson-g12a-ao-cec" - reg : Physical base address of the IP registers and length of memory mapped region. - interrupts : AO-CEC interrupt number to the CPU. - clocks : from common clock binding: handle to AO-CEC clock. - - clock-names : from common clock binding: must contain "core", - corresponding to entry in the clocks property. + - clock-names : from common clock binding, must contain : + For GXBB, GXL, GXM and G12A (AO_CEC_A module) : + - "core" + For G12A (AO_CEC_B module) : + - "oscin" + corresponding to entry in the clocks property. - hdmi-phandle: phandle to the HDMI controller Example: diff --git a/Documentation/devicetree/bindings/media/rcar_imr.txt b/Documentation/devicetree/bindings/media/rcar_imr.txt new file mode 100644 index 000000000000..b0614153ed36 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rcar_imr.txt @@ -0,0 +1,31 @@ +Renesas R-Car Image Renderer (Distortion Correction Engine) +----------------------------------------------------------- + +The image renderer, or the distortion correction engine, is a drawing processor +with a simple instruction system capable of referencing video capture data or +data in an external memory as 2D texture data and performing texture mapping +and drawing with respect to any shape that is split into triangular objects. + +Required properties: + +- compatible: "renesas,<soctype>-imr-lx4", "renesas,imr-lx4" as a fallback for + the image renderer light extended 4 (IMR-LX4) found in the R-Car gen3 SoCs, + where the examples with <soctype> are: + - "renesas,r8a7795-imr-lx4" for R-Car H3, + - "renesas,r8a7796-imr-lx4" for R-Car M3-W. +- reg: offset and length of the register block; +- interrupts: single interrupt specifier; +- clocks: single clock phandle/specifier pair; +- power-domains: power domain phandle/specifier pair; +- resets: reset phandle/specifier pair. + +Example: + + imr-lx4@fe860000 { + compatible = "renesas,r8a7795-imr-lx4", "renesas,imr-lx4"; + reg = <0 0xfe860000 0 0x2000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 823>; + power-domains = <&sysc R8A7795_PD_A3VC>; + resets = <&cpg 823>; + }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 0dd84a183ca7..aa217b096279 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -7,12 +7,14 @@ family of devices. Each VIN instance has a single parallel input that supports RGB and YUV video, with both external synchronization and BT.656 synchronization for the latter. Depending on the instance the VIN input is connected to external SoC pins, or -on Gen3 platforms to a CSI-2 receiver. +on Gen3 and RZ/G2 platforms to a CSI-2 receiver. - compatible: Must be one or more of the following - "renesas,vin-r8a7743" for the R8A7743 device - "renesas,vin-r8a7744" for the R8A7744 device - "renesas,vin-r8a7745" for the R8A7745 device + - "renesas,vin-r8a774a1" for the R8A774A1 device + - "renesas,vin-r8a774c0" for the R8A774C0 device - "renesas,vin-r8a7778" for the R8A7778 device - "renesas,vin-r8a7779" for the R8A7779 device - "renesas,vin-r8a7790" for the R8A7790 device @@ -61,10 +63,10 @@ The per-board settings Gen2 platforms: - data-enable-active: polarity of CLKENB signal, see [1] for description. Default is active high. -The per-board settings Gen3 platforms: +The per-board settings Gen3 and RZ/G2 platforms: -Gen3 platforms can support both a single connected parallel input source -from external SoC pins (port@0) and/or multiple parallel input sources +Gen3 and RZ/G2 platforms can support both a single connected parallel input +source from external SoC pins (port@0) and/or multiple parallel input sources from local SoC CSI-2 receivers (port@1) depending on SoC. - renesas,id - ID number of the VIN, VINx in the documentation. diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt index 3ec91803ba58..79c37395b396 100644 --- a/Documentation/devicetree/bindings/media/renesas,fcp.txt +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -2,8 +2,9 @@ Renesas R-Car Frame Compression Processor (FCP) ----------------------------------------------- The FCP is a companion module of video processing modules in the Renesas R-Car -Gen3 SoCs. It provides data compression and decompression, data caching, and -conversion of AXI transactions in order to reduce the memory bandwidth. +Gen3 and RZ/G2 SoCs. It provides data compression and decompression, data +caching, and conversion of AXI transactions in order to reduce the memory +bandwidth. There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP for FDP (FCPF). Their configuration and behaviour depend on the module they diff --git a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt index 541d936b62e8..331409259752 100644 --- a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt +++ b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt @@ -2,12 +2,14 @@ Renesas R-Car MIPI CSI-2 ------------------------ The R-Car CSI-2 receiver device provides MIPI CSI-2 capabilities for the -Renesas R-Car family of devices. It is used in conjunction with the +Renesas R-Car and RZ/G2 family of devices. It is used in conjunction with the R-Car VIN module, which provides the video capture capabilities. Mandatory properties -------------------- - compatible: Must be one or more of the following + - "renesas,r8a774a1-csi2" for the R8A774A1 device. + - "renesas,r8a774c0-csi2" for the R8A774C0 device. - "renesas,r8a7795-csi2" for the R8A7795 device. - "renesas,r8a7796-csi2" for the R8A7796 device. - "renesas,r8a77965-csi2" for the R8A77965 device. @@ -17,7 +19,8 @@ Mandatory properties - reg: the register base and size for the device registers - interrupts: the interrupt for the device - - clocks: reference to the parent clock + - clocks: A phandle + clock specifier for the module clock + - resets: A phandle + reset specifier for the module reset The device node shall contain two 'port' child nodes according to the bindings defined in Documentation/devicetree/bindings/media/ diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 16427017cb45..cd5a955b2ea0 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -2,13 +2,13 @@ The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. -It can be found in the Renesas R-Car second generation SoCs. +It can be found in the Renesas R-Car Gen2, R-Car Gen3, RZ/G1, and RZ/G2 SoCs. Required properties: - compatible: Must contain one of the following values - - "renesas,vsp1" for the R-Car Gen2 VSP1 - - "renesas,vsp2" for the R-Car Gen3 VSP2 + - "renesas,vsp1" for the R-Car Gen2 and RZ/G1 VSP1 + - "renesas,vsp2" for the R-Car Gen3 and RZ/G2 VSP2 - reg: Base address and length of the registers block for the VSP. - interrupts: VSP interrupt specifier. diff --git a/Documentation/devicetree/bindings/media/si470x.txt b/Documentation/devicetree/bindings/media/si470x.txt new file mode 100644 index 000000000000..a9403558362e --- /dev/null +++ b/Documentation/devicetree/bindings/media/si470x.txt @@ -0,0 +1,26 @@ +* Silicon Labs FM Radio receiver + +The Silicon Labs Si470x is family of FM radio receivers with receive power scan +supporting 76-108 MHz, programmable through an I2C interface. +Some of them includes an RDS encoder. + +Required Properties: +- compatible: Should contain "silabs,si470x" +- reg: the I2C address of the device + +Optional Properties: +- interrupts : The interrupt number +- reset-gpios: GPIO specifier for the chips reset line + +Example: + +&i2c2 { + si470x@63 { + compatible = "silabs,si470x"; + reg = <0x63>; + + interrupt-parent = <&gpj2>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpj2 5 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt index d4ab34f2240c..0dd540bb03db 100644 --- a/Documentation/devicetree/bindings/media/sun6i-csi.txt +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt @@ -6,8 +6,9 @@ Allwinner V3s SoC features a CSI module(CSI1) with parallel interface. Required properties: - compatible: value must be one of: * "allwinner,sun6i-a31-csi" - * "allwinner,sun8i-h3-csi", "allwinner,sun6i-a31-csi" + * "allwinner,sun8i-h3-csi" * "allwinner,sun8i-v3s-csi" + * "allwinner,sun50i-a64-csi" - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the CSI |