1 files changed, 0 insertions, 97 deletions
diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt
deleted file mode 100644
index 21f31fdf5543..000000000000
--- a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt
+++ /dev/null
@@ -1,97 +0,0 @@
-Samsung S5C73M3 8Mp camera ISP
-------------------------------
-
-The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video
-data busses. The I2C bus is the main control bus and additionally the SPI bus
-is used, mostly for transferring the firmware to and from the device. Two
-slave device nodes corresponding to these control bus interfaces are required
-and should be placed under respective bus controller nodes.
-
-I2C slave device node
----------------------
-
-Required properties:
-
-- compatible	    : "samsung,s5c73m3";
-- reg		    : I2C slave address of the sensor;
-- vdd-int-supply    : digital power supply (1.2V);
-- vdda-supply	    : analog power supply (1.2V);
-- vdd-reg-supply    : regulator input power supply (2.8V);
-- vddio-host-supply : host I/O power supply (1.8V to 2.8V);
-- vddio-cis-supply  : CIS I/O power supply (1.2V to 1.8V);
-- vdd-af-supply     : lens power supply (2.8V);
-- xshutdown-gpios   : specifier of GPIO connected to the XSHUTDOWN pin;
-- standby-gpios     : specifier of GPIO connected to the STANDBY pin;
-- clocks	    : should contain list of phandle and clock specifier pairs
-		      according to common clock bindings for the clocks described
-		      in the clock-names property;
-- clock-names	    : should contain "cis_extclk" entry for the CIS_EXTCLK clock;
-
-Optional properties:
-
-- clock-frequency   : the frequency at which the "cis_extclk" clock should be
-		      configured to operate, in Hz; if this property is not
-		      specified default 24 MHz value will be used.
-
-The common video interfaces bindings (see video-interfaces.txt) should be used
-to specify link from the S5C73M3 to an external image data receiver. The S5C73M3
-device node should contain one 'port' child node with an 'endpoint' subnode for
-this purpose. The data link from a raw image sensor to the S5C73M3 can be
-similarly specified, but it is optional since the S5C73M3 ISP and a raw image
-sensor are usually inseparable and form a hybrid module.
-
-Following properties are valid for the endpoint node(s):
-
-endpoint subnode
-----------------
-
-- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
-  video-interfaces.txt. This sensor doesn't support data lane remapping
-  and physical lane indexes in subsequent elements of the array should
-  be only consecutive ascending values.
-
-SPI device node
----------------
-
-Required properties:
-
-- compatible	    : "samsung,s5c73m3";
-
-For more details see description of the SPI busses bindings
-(../spi/spi-bus.txt) and bindings of a specific bus controller.
-
-Example:
-
-i2c@138a000000 {
-	...
-	s5c73m3@3c {
-		compatible = "samsung,s5c73m3";
-		reg = <0x3c>;
-		vdd-int-supply = <&buck9_reg>;
-		vdda-supply = <&ldo17_reg>;
-		vdd-reg-supply = <&cam_io_reg>;
-		vddio-host-supply = <&ldo18_reg>;
-		vddio-cis-supply = <&ldo9_reg>;
-		vdd-af-supply = <&cam_af_reg>;
-		clock-frequency = <24000000>;
-		clocks = <&clk 0>;
-		clock-names = "cis_extclk";
-		reset-gpios = <&gpf1 3 1>;
-		standby-gpios = <&gpm0 1 1>;
-		port {
-			s5c73m3_ep: endpoint {
-				remote-endpoint = <&csis0_ep>;
-				data-lanes = <1 2 3 4>;
-			};
-		};
-	};
-};
-
-spi@1392000 {
-	...
-	s5c73m3_spi: s5c73m3@0 {
-		compatible = "samsung,s5c73m3";
-		reg = <0>;
-		...
-	};
-};