diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input')
16 files changed, 464 insertions, 38 deletions
diff --git a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt index 0c252d9306da..ef2ae729718f 100644 --- a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt +++ b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt @@ -1,13 +1,19 @@ Samsung tm2-touchkey Required properties: -- compatible: must be "cypress,tm2-touchkey" +- compatible: + * "cypress,tm2-touchkey" - for the touchkey found on the tm2 board + * "cypress,midas-touchkey" - for the touchkey found on midas boards + * "cypress,aries-touchkey" - for the touchkey found on aries boards - reg: I2C address of the chip. - interrupts: interrupt to which the chip is connected (see interrupt binding[0]). - vcc-supply : internal regulator output. 1.8V - vdd-supply : power supply for IC 3.3V +Optional properties: +- linux,keycodes: array of keycodes (max 4), default KEY_PHONE and KEY_BACK + [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt Example: @@ -21,5 +27,6 @@ Example: interrupts = <2 IRQ_TYPE_EDGE_FALLING>; vcc-supply=<&ldo32_reg>; vdd-supply=<&ldo33_reg>; + linux,keycodes = <KEY_PHONE KEY_BACK>; }; }; diff --git a/Documentation/devicetree/bindings/input/gpio-vibrator.yaml b/Documentation/devicetree/bindings/input/gpio-vibrator.yaml new file mode 100644 index 000000000000..903475f52dbd --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-vibrator.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/input/gpio-vibrator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO vibrator + +maintainers: + - Luca Weiss <luca@z3ntu.xyz> + +description: |+ + Registers a GPIO device as vibrator, where the on/off capability is controlled by a GPIO. + +properties: + compatible: + const: gpio-vibrator + + enable-gpios: + maxItems: 1 + + vcc-supply: + description: Regulator that provides power + +required: + - compatible + - enable-gpios + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + vibrator { + compatible = "gpio-vibrator"; + enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>; + vcc-supply = <&pm8941_l18>; + }; diff --git a/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt new file mode 100644 index 000000000000..b2a76301e632 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt @@ -0,0 +1,25 @@ +Ilitek ILI210x/ILI251x touchscreen controller + +Required properties: +- compatible: + ilitek,ili210x for ILI210x + ilitek,ili251x for ILI251x + +- reg: The I2C address of the device + +- interrupts: The sink for the touchscreen's IRQ output + See ../interrupt-controller/interrupts.txt + +Optional properties for main touchpad device: + +- reset-gpios: GPIO specifier for the touchscreen's reset pin (active low) + +Example: + + touchscreen@41 { + compatible = "ilitek,ili251x"; + reg = <0x41>; + interrupt-parent = <&gpio4>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt index bcf62f856358..2b075a080d30 100644 --- a/Documentation/devicetree/bindings/input/lpc32xx-key.txt +++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt @@ -8,6 +8,7 @@ Required Properties: - reg: Physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. +- clocks: phandle to clock controller plus clock-specifier pair - nxp,debounce-delay-ms: Debounce delay in ms - nxp,scan-delay-ms: Repeated scan period in ms - linux,keymap: the key-code to be reported when the key is pressed @@ -22,7 +23,9 @@ Example: key@40050000 { compatible = "nxp,lpc3220-key"; reg = <0x40050000 0x1000>; - interrupts = <54 0>; + clocks = <&clk LPC32XX_CLK_KEY>; + interrupt-parent = <&sic1>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; keypad,num-rows = <1>; keypad,num-columns = <1>; nxp,debounce-delay-ms = <3>; diff --git a/Documentation/devicetree/bindings/input/max77650-onkey.txt b/Documentation/devicetree/bindings/input/max77650-onkey.txt new file mode 100644 index 000000000000..477dc74f452a --- /dev/null +++ b/Documentation/devicetree/bindings/input/max77650-onkey.txt @@ -0,0 +1,26 @@ +Onkey driver for MAX77650 PMIC from Maxim Integrated. + +This module is part of the MAX77650 MFD device. For more details +see Documentation/devicetree/bindings/mfd/max77650.txt. + +The onkey controller is represented as a sub-node of the PMIC node on +the device tree. + +Required properties: +-------------------- +- compatible: Must be "maxim,max77650-onkey". + +Optional properties: +- linux,code: The key-code to be reported when the key is pressed. + Defaults to KEY_POWER. +- maxim,onkey-slide: The system's button is a slide switch, not the default + push button. + +Example: +-------- + + onkey { + compatible = "maxim,max77650-onkey"; + linux,code = <KEY_END>; + maxim,onkey-slide; + }; diff --git a/Documentation/devicetree/bindings/input/microchip,qt1050.txt b/Documentation/devicetree/bindings/input/microchip,qt1050.txt new file mode 100644 index 000000000000..80e75f96252b --- /dev/null +++ b/Documentation/devicetree/bindings/input/microchip,qt1050.txt @@ -0,0 +1,78 @@ +Microchip AT42QT1050 Five-channel Touch Sensor IC + +The AT42QT1050 (QT1050) is a QTouchADC sensor device. The device can sense from +one to five keys, dependent on mode. The QT1050 includes all signal processing +functions necessary to provide stable sensing under a wide variety of changing +conditions, and the outputs are fully debounced. + +The touchkey device node should be placed inside an I2C bus node. + +Required properties: +- compatible: Must be "microchip,qt1050" +- reg: The I2C address of the device +- interrupts: The sink for the touchpad's IRQ output, + see ../interrupt-controller/interrupts.txt + +Optional properties: +- wakeup-source: touch keys can be used as a wakeup source + +Each button (key) is represented as a sub-node: + +Each not specified key or key with linux,code set to KEY_RESERVED gets disabled +in HW. + +Subnode properties: +- linux,code: Keycode to emit. +- reg: The key number. Valid values: 0, 1, 2, 3, 4. + +Optional subnode-properties: + +If a optional property is missing or has a invalid value the default value is +taken. + +- microchip,pre-charge-time-ns: + Each touchpad need some time to precharge. The value depends on the mechanical + layout. + Valid value range: 0 - 637500; values must be a multiple of 2500; + default is 0. +- microchip,average-samples: + Number of data samples which are averaged for each read. + Valid values: 1, 4, 16, 64, 256, 1024, 4096, 16384; default is 1. +- microchip,average-scaling: + The scaling factor which is used to scale the average-samples. + Valid values: 1, 2, 4, 8, 16, 32, 64, 128; default is 1. +- microchip,threshold: + Number of counts to register a touch detection. + Valid value range: 0 - 255; default is 20. + +Example: +QT1050 with 3 non continuous keys, key2 and key4 are disabled. + +touchkeys@41 { + compatible = "microchip,qt1050"; + reg = <0x41>; + interrupt-parent = <&gpio0>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + + up@0 { + reg = <0>; + linux,code = <KEY_UP>; + microchip,average-samples = <64>; + microchip,average-scaling = <16>; + microchip,pre-charge-time-ns = <10000>; + }; + + right@1 { + reg = <1>; + linux,code = <KEY_RIGHT>; + microchip,average-samples = <64>; + microchip,average-scaling = <8>; + }; + + down@3 { + reg = <3>; + linux,code = <KEY_DOWN>; + microchip,average-samples = <256>; + microchip,average-scaling = <16>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/msm-vibrator.txt b/Documentation/devicetree/bindings/input/msm-vibrator.txt new file mode 100644 index 000000000000..8dcf014ef2e5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/msm-vibrator.txt @@ -0,0 +1,36 @@ +* Device tree bindings for the Qualcomm MSM vibrator + +Required properties: + + - compatible: Should be one of + "qcom,msm8226-vibrator" + "qcom,msm8974-vibrator" + - reg: the base address and length of the IO memory for the registers. + - pinctrl-names: set to default. + - pinctrl-0: phandles pointing to pin configuration nodes. See + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + - clock-names: set to pwm + - clocks: phandle of the clock. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + - enable-gpios: GPIO that enables the vibrator. + +Optional properties: + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example from a LG Nexus 5 (hammerhead) phone: + +vibrator@fd8c3450 { + reg = <0xfd8c3450 0x400>; + compatible = "qcom,msm8974-vibrator"; + + vcc-supply = <&pm8941_l19>; + + clocks = <&mmcc CAMSS_GP1_CLK>; + clock-names = "pwm"; + + enable-gpios = <&msmgpio 60 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_pin>; +}; diff --git a/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt new file mode 100644 index 000000000000..4494613ae7ad --- /dev/null +++ b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt @@ -0,0 +1,28 @@ +STMicroelectronics STPMIC1 Onkey + +Required properties: + +- compatible = "st,stpmic1-onkey"; +- interrupts: interrupt line to use +- interrupt-names = "onkey-falling", "onkey-rising" + onkey-falling: happens when onkey is pressed; IT_PONKEY_F of pmic + onkey-rising: happens when onkey is released; IT_PONKEY_R of pmic + +Optional properties: + +- st,onkey-clear-cc-flag: onkey is able power on after an + over-current shutdown event. +- st,onkey-pu-inactive: onkey pull up is not active +- power-off-time-sec: Duration in seconds which the key should be kept + pressed for device to power off automatically (from 1 to 16 seconds). + see See Documentation/devicetree/bindings/input/keys.txt + +Example: + +onkey { + compatible = "st,stpmic1-onkey"; + interrupt-parent = <&pmic>; + interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; +}; diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt index 1458c3179a63..496125c6bfb7 100644 --- a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt +++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt @@ -2,12 +2,14 @@ Allwinner sun4i low res adc attached tablet keys ------------------------------------------------ Required properties: - - compatible: "allwinner,sun4i-a10-lradc-keys" + - compatible: should be one of the following string: + "allwinner,sun4i-a10-lradc-keys" + "allwinner,sun8i-a83t-r-lradc" - reg: mmio address range of the chip - interrupts: interrupt to which the chip is connected - vref-supply: powersupply for the lradc reference voltage -Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys": +Each key is represented as a sub-node of the compatible mentioned above: Required subnode-properties: - label: Descriptive name of the key. diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt index da2dc5d6c98b..870b8c5cce9b 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -1,11 +1,12 @@ FocalTech EDT-FT5x06 Polytouch driver ===================================== -There are 3 variants of the chip for various touch panel sizes +There are 5 variants of the chip for various touch panel sizes FT5206GE1 2.8" .. 3.8" FT5306DE4 4.3" .. 7" FT5406EE8 7" .. 8.9" FT5506EEG 7" .. 8.9" +FT5726NEI 5.7” .. 11.6" The software interface is identical for all those chips, so that currently there is no need for the driver to distinguish between the @@ -19,6 +20,7 @@ Required properties: or: "edt,edt-ft5306" or: "edt,edt-ft5406" or: "edt,edt-ft5506" + or: "evervision,ev-ft5726" or: "focaltech,ft6236" - reg: I2C slave address of the chip (0x38) @@ -42,6 +44,15 @@ Optional properties: - offset: allows setting the edge compensation in the range from 0 to 31. + + - offset-x: Same as offset, but applies only to the horizontal position. + Range from 0 to 80, only supported by evervision,ev-ft5726 + devices. + + - offset-y: Same as offset, but applies only to the vertical position. + Range from 0 to 80, only supported by evervision,ev-ft5726 + devices. + - touchscreen-size-x : See touchscreen.txt - touchscreen-size-y : See touchscreen.txt - touchscreen-fuzz-x : See touchscreen.txt diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt index f7e95c52f3c7..fc03ea4cf5ab 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt @@ -3,6 +3,8 @@ Device tree bindings for Goodix GT9xx series touchscreen controller Required properties: - compatible : Should be "goodix,gt1151" + or "goodix,gt5663" + or "goodix,gt5688" or "goodix,gt911" or "goodix,gt9110" or "goodix,gt912" @@ -18,11 +20,16 @@ Optional properties: - irq-gpios : GPIO pin used for IRQ. The driver uses the interrupt gpio pin as output to reset the device. - reset-gpios : GPIO pin used for reset - - - touchscreen-inverted-x : X axis is inverted (boolean) - - touchscreen-inverted-y : Y axis is inverted (boolean) - - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) - (swapping is done after inverting the axis) + - AVDD28-supply : Analog power supply regulator on AVDD28 pin + - VDDIO-supply : GPIO power supply regulator on VDDIO pin + - touchscreen-inverted-x + - touchscreen-inverted-y + - touchscreen-size-x + - touchscreen-size-y + - touchscreen-swapped-x-y + +The touchscreen-* properties are documented in touchscreen.txt in this +directory. Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt b/Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt new file mode 100644 index 000000000000..efa0820e2469 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt @@ -0,0 +1,80 @@ +Azoteq IQS550/572/525 Trackpad/Touchscreen Controller + +Required properties: + +- compatible : Must be equal to one of the following: + "azoteq,iqs550" + "azoteq,iqs572" + "azoteq,iqs525" + +- reg : I2C slave address for the device. + +- interrupts : GPIO to which the device's active-high RDY + output is connected (see [0]). + +- reset-gpios : GPIO to which the device's active-low NRST + input is connected (see [1]). + +Optional properties: + +- touchscreen-min-x : See [2]. + +- touchscreen-min-y : See [2]. + +- touchscreen-size-x : See [2]. If this property is omitted, the + maximum x-coordinate is specified by the + device's "X Resolution" register. + +- touchscreen-size-y : See [2]. If this property is omitted, the + maximum y-coordinate is specified by the + device's "Y Resolution" register. + +- touchscreen-max-pressure : See [2]. Pressure is expressed as the sum of + the deltas across all channels impacted by a + touch event. A channel's delta is calculated + as its count value minus a reference, where + the count value is inversely proportional to + the channel's capacitance. + +- touchscreen-fuzz-x : See [2]. + +- touchscreen-fuzz-y : See [2]. + +- touchscreen-fuzz-pressure : See [2]. + +- touchscreen-inverted-x : See [2]. Inversion is applied relative to that + which may already be specified by the device's + FLIP_X and FLIP_Y register fields. + +- touchscreen-inverted-y : See [2]. Inversion is applied relative to that + which may already be specified by the device's + FLIP_X and FLIP_Y register fields. + +- touchscreen-swapped-x-y : See [2]. Swapping is applied relative to that + which may already be specified by the device's + SWITCH_XY_AXIS register field. + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt +[2]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt + +Example: + + &i2c1 { + /* ... */ + + touchscreen@74 { + compatible = "azoteq,iqs550"; + reg = <0x74>; + interrupt-parent = <&gpio>; + interrupts = <17 4>; + reset-gpios = <&gpio 27 1>; + + touchscreen-size-x = <640>; + touchscreen-size-y = <480>; + + touchscreen-max-pressure = <16000>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt index 64ad48b824a2..019373253b28 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt @@ -1,13 +1,17 @@ -* Sitronix st1232 touchscreen controller +* Sitronix st1232 or st1633 touchscreen controller Required properties: -- compatible: must be "sitronix,st1232" +- compatible: must contain one of + * "sitronix,st1232" + * "sitronix,st1633" - reg: I2C address of the chip - interrupts: interrupt to which the chip is connected Optional properties: - gpios: a phandle to the reset GPIO +For additional optional properties see: touchscreen.txt + Example: i2c@00000000 { diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt index 127baa31a77a..c549924603d2 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -5,39 +5,105 @@ Required properties: - compatible: "st,stmpe-ts" Optional properties: -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 - -> 144 clocks), recommended is 4. -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external - reference) -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 - samples, 3 -> 8 samples) -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended - is 3 -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of - the fractional part) recommended is 7 -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 - mA max, 1 -> 50 mA typical 80 mA max) +- st,ave-ctrl : Sample average control + 0 -> 1 sample + 1 -> 2 samples + 2 -> 4 samples + 3 -> 8 samples +- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) + 0 -> 10 us + 1 -> 50 us + 2 -> 100 us + 3 -> 500 us + 4 -> 1 ms + 5 -> 5 ms + 6 -> 10 ms + 7 -> 50 ms +- st,settling : Panel driver settling time (recommended is 2) + 0 -> 10 us + 1 -> 100 us + 2 -> 500 us + 3 -> 1 ms + 4 -> 5 ms + 5 -> 10 ms + 6 -> 50 ms + 7 -> 100 ms +- st,fraction-z : Length of the fractional part in z (recommended is 7) + (fraction-z ([0..7]) = Count of the fractional part) +- st,i-drive : current limit value of the touchscreen drivers + 0 -> 20 mA (typical 35mA max) + 1 -> 50 mA (typical 80 mA max) + +Optional properties common with MFD (deprecated): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks + 1 -> 44 clocks + 2 -> 56 clocks + 3 -> 64 clocks + 4 -> 80 clocks (recommended) + 5 -> 96 clocks + 6 -> 124 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC + 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal + 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz + 1 -> 3.25 MHz + 2 || 3 -> 6.5 MHz Node name must be stmpe_touchscreen and should be child node of stmpe node to which it belongs. +Note that common ADC settings of stmpe_touchscreen (child) will take precedence +over the settings done in MFD. + Example: +stmpe811@41 { + compatible = "st,stmpe811"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touch_int>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio4>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + /* Common ADC settings */ + /* 3.25 MHz ADC clock speed */ + st,adc-freq = <1>; + /* 12-bit ADC */ + st,mod-12b = <1>; + /* internal ADC reference */ + st,ref-sel = <0>; + /* ADC converstion time: 80 clocks */ + st,sample-time = <4>; + stmpe_touchscreen { compatible = "st,stmpe-ts"; - st,sample-time = <4>; - st,mod-12b = <1>; - st,ref-sel = <0>; - st,adc-freq = <1>; - st,ave-ctrl = <1>; - st,touch-det-delay = <2>; - st,settling = <2>; + reg = <0>; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 7 length fractional part in z */ st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ st,i-drive = <1>; }; + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt index 4886c4aa2906..0ebe6dd043c7 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt @@ -1,10 +1,17 @@ * Semtech SX8654 I2C Touchscreen Controller Required properties: -- compatible: must be "semtech,sx8654" +- compatible: must be one of the following, depending on the model: + "semtech,sx8650" + "semtech,sx8654" + "semtech,sx8655" + "semtech,sx8656" - reg: i2c slave address - interrupts: touch controller interrupt +Optional properties: + - reset-gpios: GPIO specification for the NRST input + Example: sx8654@48 { @@ -12,4 +19,5 @@ Example: reg = <0x48>; interrupt-parent = <&gpio6>; interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt index b1163bf97146..aad5e34965eb 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -2,7 +2,12 @@ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Required properties: +- mfd + compatible: Should be + "ti,am3359-tscadc" for AM335x/AM437x SoCs + "ti,am654-tscadc", "ti,am3359-tscadc" for AM654 SoCs - child "tsc" + compatible: Should be "ti,am3359-tsc". ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen support on the platform. ti,x-plate-resistance: X plate resistance @@ -25,6 +30,9 @@ Required properties: AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. XP = 0, XN = 1, YP = 2, YN = 3. - child "adc" + compatible: Should be + "ti,am3359-adc" for AM335x/AM437x SoCs + "ti,am654-adc", "ti,am3359-adc" for AM654 SoCs ti,adc-channels: List of analog inputs available for ADC. AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. |