| Age | Commit message (Collapse) | Author |
|---|
|
When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:
* associate
* start aggregation session
* driver callback
* disassociate
* associate again to the same AP
* callback processing runs, leading to a WARN_ON() that
the TID hadn't requested aggregation
If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.
Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In VHT, the specification allows to limit the number of
MSDUs in an A-MSDU in the Extended Capabilities IE. There
is also a limitation on the byte size in the VHT IE.
In HT, the only limitation is on the byte size.
Parse the capabilities from the peer and make them
available to the driver.
In HT, there is another limitation when a BA agreement
is active: the byte size can't be greater than 4095.
This is not enforced here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add VHT support for IBSS. Drivers could activate
this feature by setting NL80211_EXT_FEATURE_VHT_IBSS
flag.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Set for completeness mostly, currently unused in the code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the HT capabilities and HT operation information elements to TDLS
setup packets where appropriate.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This can be useful for testing purposes to confirm valid AP behavior on
HT 20/40 co-existence functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows user-space (wpa_supplicant) to disable LDPC coding.
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Previously we were warning and using automatic when a driver sent an
update request with SMPS off. This patch makes it possible for
drivers to disable SMPS at runtime, for whatever reason.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
sdata->u.ap.request_smps_work can’t be flushed synchronously
under wdev_lock(wdev) since ieee80211_request_smps_ap_work
itself locks the same lock.
While at it, reset the driver_smps_mode when the ap is
stopped to its default: OFF.
This solves:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0-ipeer+ #2 Tainted: G O
-------------------------------------------------------
rmmod/2867 is trying to acquire lock:
((&sdata->u.ap.request_smps_work)){+.+...}, at: [<c105b8d0>] flush_work+0x0/0x90
but task is already holding lock:
(&wdev->mtx){+.+.+.}, at: [<f9b32626>] cfg80211_stop_ap+0x26/0x230 [cfg80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&wdev->mtx){+.+.+.}:
[<c10aefa9>] lock_acquire+0x79/0xe0
[<c1607a1a>] mutex_lock_nested+0x4a/0x360
[<fb06288b>] ieee80211_request_smps_ap_work+0x2b/0x50 [mac80211]
[<c105cdd8>] process_one_work+0x198/0x450
[<c105d469>] worker_thread+0xf9/0x320
[<c10669ff>] kthread+0x9f/0xb0
[<c1613397>] ret_from_kernel_thread+0x1b/0x28
-> #0 ((&sdata->u.ap.request_smps_work)){+.+...}:
[<c10ae9df>] __lock_acquire+0x183f/0x1910
[<c10aefa9>] lock_acquire+0x79/0xe0
[<c105b917>] flush_work+0x47/0x90
[<c105d867>] __cancel_work_timer+0x67/0xe0
[<c105d90f>] cancel_work_sync+0xf/0x20
[<fb0765cc>] ieee80211_stop_ap+0x8c/0x340 [mac80211]
[<f9b3268c>] cfg80211_stop_ap+0x8c/0x230 [cfg80211]
[<f9b0d8f9>] cfg80211_leave+0x79/0x100 [cfg80211]
[<f9b0da72>] cfg80211_netdev_notifier_call+0xf2/0x4f0 [cfg80211]
[<c160f2c9>] notifier_call_chain+0x59/0x130
[<c106c6de>] __raw_notifier_call_chain+0x1e/0x30
[<c106c70f>] raw_notifier_call_chain+0x1f/0x30
[<c14f8213>] call_netdevice_notifiers_info+0x33/0x70
[<c14f8263>] call_netdevice_notifiers+0x13/0x20
[<c14f82a4>] __dev_close_many+0x34/0xb0
[<c14f83fe>] dev_close_many+0x6e/0xc0
[<c14f9c77>] rollback_registered_many+0xa7/0x1f0
[<c14f9dd4>] unregister_netdevice_many+0x14/0x60
[<fb06f4d9>] ieee80211_remove_interfaces+0xe9/0x170 [mac80211]
[<fb055116>] ieee80211_unregister_hw+0x56/0x110 [mac80211]
[<fa3e9396>] iwl_op_mode_mvm_stop+0x26/0xe0 [iwlmvm]
[<f9b9d8ca>] _iwl_op_mode_stop+0x3a/0x70 [iwlwifi]
[<f9b9d96f>] iwl_opmode_deregister+0x6f/0x90 [iwlwifi]
[<fa405179>] __exit_compat+0xd/0x19 [iwlmvm]
[<c10b8bf9>] SyS_delete_module+0x179/0x2b0
[<c1613421>] sysenter_do_call+0x12/0x32
Fixes: 687da132234f ("mac80211: implement SMPS for AP")
Cc: <stable@vger.kernel.org> [3.13]
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ATM, {ADD,DEL}BA and BAR frames are sent on the AC matching the TID of
the BA parameters. In the discussion [1] about this patch, Johannes
recalled that it fixed some races with the DELBA and indeed this
behavior was introduced in [2].
While [2] is right for the BARs, the part queueing the {ADD,DEL}BAs on
their BA params TID AC violates the spec and is more a workaround for
some drivers. Helmut expressed some concerns wrt such drivers, in
particular DELBAs in rt2x00.
ATM, DELBAs are sent after a driver has called (hence "purposely")
ieee80211_start_tx_ba_cb_irqsafe and Johannes and Emmanuel gave some
details wrt intentions behind the split of the IEEE80211_AMPDU_TX_STOP_*
given to the driver ampdu_action supposed to call this function, which
could prove handy to people trying to do the right thing in faulty
drivers (if their fw/hw don't get in their way).
[1] http://mid.gmane.org/1390391564-18481-1-git-send-email-karl.beldan@gmail.com
[2] Commit: cf6bb79ad828 ("mac80211: Use appropriate TID for sending BAR, ADDBA and DELBA frames")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In managed mode, we should not ask for OFF mode because the
power settings may still require DYNAMIC. In AP mode, this
should be allowed since the default settings is OFF and
AUTOMATIC is not allowed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
All accesses of the tid_start_tx lock should be protected
by sta->lock if there is any chance that another thread
could still be accessing the sta object.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
HT capabilites are asymmetric -- e.g. beamforming is both an
RX and TX capability. If, for example, we support RX but not
TX, the RX capability of the AP station is masked out (if it
supports it). This works correctly if it's really the driver
capability.
If, on the other hand, the reason for not supporting TX BF
is that it was removed by HT capability overrides then the
wrong thing happens: the AP's TX capability will be removed
rather than its RX capability, because the override function
works on own capabilities, not remote ones, and doesn't take
the asymmetry into account.
To fix this make a copy of our own capabilities, apply the
overrides to them (where needed) and then use that to set up
the peer's capabilities.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The HT overrides are intended only for the connection
to the AP, not for any other purpose. Therefore, don't
apply them to TDLS peers that are also stations added
to a managed station interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make all the parsed IE pointers const, and propagate
the change to all the users etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Handle the operating mode notification action frame.
When the supported streams or the bandwidth change
let the driver and rate control algorithm know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Bail out if no update is made to the SMPS state. This
allows the driver to avoid duplicating the state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When an interface is configured to a 20 MHz channel
and the device as well as the peer are 40 MHz capable
the HT capabilities of the peer are not restricted to
20 MHz, even though they're supposed to be restricted
to the currently possible capabilities.
Unset the 40 MHz HT capability bits in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The initiator/tx doesn't really identify why an
aggregation session is stopped, give a reason
for stopping that more clearly identifies what's
going on. This will help tell the driver clearly
what is expected of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows user-space (wpa_supplicant) to disable
short guard interval (SGI) for 20Mhz. The SGI-40
disable option is already handled.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduce IEEE80211_NUM_TIDS in the generic 802.11
header file and use it in place of STA_TID_NUM and
NUM_RX_DATA_QUEUES which are both really the number
of TIDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing the channel type during operation is
confusing to some drivers and will be hard to
handle in multi-channel scenarios. Instead of
changing the channel, set it to the right HT
channel before authenticating/associating and
don't change it -- just update the 20/40 MHz
restrictions in rate control as needed when
changed by the AP.
This also fixes a problem that Paul missed in
his fix for the "regulatory makes us deaf"
issue -- when we couldn't use 40 MHz we still
associated saying we were using 40 MHz, which
could in similarly broken APs make us never
even connect successfully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently BAR, ADDBA and DELBA frames are always sent using AC_VO. If
the TID for which a BA session is established is assigned to a different
queue BAR, ADDBA and DELBA frames can "overtake" frames of the according
BA session.
Hence, always put BA session related frames into the same queue as the
BA sessions data frames.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AP interfaces routinely call this logic, so just silently
return when this happens instead of splatting the kernel
logs.
Reported-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The HT mode is set by iw (previous patchsets).
The interface is set into the specified HT mode.
HT mode and capabilities are announced in beacons.
If we add a station that uses HT also, the fastest matching HT mode will
be used for transmission. That means if we are using HT40+ and we add a station
running on HT40-, we would transfer at HT20.
If we join an IBSS with HT40, but the secondary channel is not
available, we will fall back into HT20 as well.
Allow frame aggregation to start in IBSS mode.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* remove implicit channel_type enum assumptions
* use rate_control_rate_init() if channel type changed
* remove channel flags check
* activate HT IBSS feature support
* slightly reword commit message
* rebase on wireless-testing
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Conflicts:
drivers/net/wireless/iwlegacy/iwl-debugfs.c
drivers/net/wireless/iwlegacy/iwl-rx.c
drivers/net/wireless/iwlegacy/iwl-scan.c
drivers/net/wireless/iwlegacy/iwl-tx.c
include/net/bluetooth/bluetooth.h
|
|
This implements ht-cap over-rides for mac80211 drivers.
HT may be disabled, making an /a/b/g/n station act like an
a/b/g station. HT40 may be disabled forcing the station to
be HT20 even if the AP and local hardware support HT40.
MAX-AMSDU may be disabled.
AMPDU-Density may be increased.
AMPDU-Factor may be decreased.
This has been successfully tested with ath9k using patched
wpa_supplicant and iw.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Ashok Nagarajan <anagar6@uic.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some devices support BT/WLAN co-existence algorigthms.
In order not to harm the system performance and user experience, the device
requests not to allow any RX BA session and tear down existing RX BA sessions
based on system constraints such as periodic BT activity that needs to limit
WLAN activity (eg.SCO or A2DP).
In such cases, the intention is to limit the duration of the RX PPDU and
therefore prevent the peer device to use A-MPDU aggregation.
Adding ieee80211_stop_rx_ba_session() callback
that can be used by the driver to stop existing BA sessions.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.
Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During my quest to make mac80211 not have any RCU
warnings from sparse, I came across the a-MPDU code
again and it wasn't quite clear why it isn't racy.
So instead of assigning the tid_tx array with just
the spinlock held in ieee80211_start_tx_ba_session
use a separate temporary array protected only by
the spinlock and protect all assignments to the
"live" array by both the spinlock and the mutex so
that other code is easily verified to be correct.
Due to pointer assignment atomicity I don't think
this is a real issue, but I'm not sure, especially
on Alpha the current code might be problematic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We need to copy this to allow drivers to look
at the information where needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It looks like I submitted a different patch
than I tested, because clearly the code in
mac80211 is missing actually propagating the
requested SMPS mode. Fix that!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Sometimes drivers have more information than the
stack about how their antennas/chains are used,
and may require that the SM PS mode be changed.
This could happen, for example, when detecting
that the user disconnected an antenna. Thus this
patch introduces API to allow drivers to request
SM PS mode changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch will also fix the odd freeze which occurred
when minstrel_ht connects to an 802.11n network with
legacy hardware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the TX
aggregation code to use the mutex the RX part
already uses. The spinlock is still necessary
around some code to avoid races with TX, but
now we can also synchronize_net() to avoid
getting an inconsistent sequence number.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the RX
aggregation code to use a mutex, so that it
would already allow drivers to sleep. But
explicitly disable BHs around the callback
for now since the TX part cannot yet sleep,
and drivers' locking might require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
Johannes Berg
Emmanuel Grumbach
Janusz.Dziedzic@tieto.com
Arik Nemtsov
Jouni Malinen
Pawel Kulakowski
Luciano Coelho
John W. Linville
Karl Beldan
Simon Wunderlich
Ben Greear
Joe Perches
Helmut Schaa
Alexander Simon
Thomas Pedersen
Paul Gortmaker
Shahar Levi
Christian Lamparter