| Age | Commit message (Collapse) | Author |
|---|
|
LED Mode:
Microsemi PHY support 2 LEDs (LED[0] and LED[1]) to display different
status information that can be selected by setting LED mode.
LED Mode parameter (vsc8531, led-0-mode) and (vsc8531, led-1-mode) get
from Device Tree.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
being specified as positive values instead of negative (both
documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
"vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Edge-rate:
As system and networking speeds increase, a signal's output transition,
also know as the edge rate or slew rate (V/ns), takes on greater importance
because high-speed signals come with a price. That price is an assortment of
interference problems like ringing on the line, signal overshoot and
undershoot, extended signal settling times, crosstalk noise, transmission
line reflections, false signal detection by the receiving device and
electromagnetic interference (EMI) -- all of which can negate the potential
gains designers are seeking when they try to increase system speeds through
the use of higher performance logic devices. The fact is, faster signaling
edge rates can cause a higher level of electrical noise or other type of
interference that can actually lead to slower line speeds and lower maximum
system frequencies. This parameter allow the board designers to change the
driving strange, and thereby change the EMI behavioral.
Edge-rate parameters (vddmac, edge-slowdown) get from Device Tree.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Raju Lakkaraju
jbrunet
Allan W. Nielsen
Dan Murphy