| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit 316ec154810960052d4586b634156c54d0778f74 upstream.
A page table upgrade in a kernel section that uses secondary address
mode will mess up the kernel instructions as follows:
Consider the following scenario: two threads are sharing memory.
On CPU1 thread 1 does e.g. strnlen_user(). That gets to
old_fs = enable_sacf_uaccess();
len = strnlen_user_srst(src, size);
and
" la %2,0(%1)\n"
" la %3,0(%0,%1)\n"
" slgr %0,%0\n"
" sacf 256\n"
"0: srst %3,%2\n"
in strnlen_user_srst(). At that point we are in secondary space mode,
control register 1 points to kernel page table and instruction fetching
happens via c1, rather than usual c13. Interrupts are not disabled, for
obvious reasons.
On CPU2 thread 2 does MAP_FIXED mmap(), forcing the upgrade of page table
from 3-level to e.g. 4-level one. We'd allocated new top-level table,
set it up and now we hit this:
notify = 1;
spin_unlock_bh(&mm->page_table_lock);
}
if (notify)
on_each_cpu(__crst_table_upgrade, mm, 0);
OK, we need to actually change over to use of new page table and we
need that to happen in all threads that are currently running. Which
happens to include the thread 1. IPI is delivered and we have
static void __crst_table_upgrade(void *arg)
{
struct mm_struct *mm = arg;
if (current->active_mm == mm)
set_user_asce(mm);
__tlb_flush_local();
}
run on CPU1. That does
static inline void set_user_asce(struct mm_struct *mm)
{
S390_lowcore.user_asce = mm->context.asce;
OK, user page table address updated...
__ctl_load(S390_lowcore.user_asce, 1, 1);
... and control register 1 set to it.
clear_cpu_flag(CIF_ASCE_PRIMARY);
}
IPI is run in home space mode, so it's fine - insns are fetched
using c13, which always points to kernel page table. But as soon
as we return from the interrupt, previous PSW is restored, putting
CPU1 back into secondary space mode, at which point we no longer
get the kernel instructions from the kernel mapping.
The fix is to only fixup the control registers that are currently in use
for user processes during the page table update. We must also disable
interrupts in enable_sacf_uaccess to synchronize the cr and
thread.mm_segment updates against the on_each-cpu.
Fixes: 0aaba41b58bc ("s390: remove all code using the access register mode")
Cc: stable@vger.kernel.org # 4.15+
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
References: CVE-2020-11884
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 556d687a4ccd54ab50a721ddde42c820545effd9 upstream.
In order to use compat_* type defininitions in device drivers
outside of CONFIG_COMPAT, move the inclusion of asm-generic/compat.h
ahead of the #ifdef.
All other architectures already do this.
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit feb8e960d780e170e992a70491eec9dd68f4dbf2 upstream.
CONFIG_PPC_KUAP_DEBUG is not selectable because it depends on PPC_32
which doesn't exists.
Fixing it leads to a deadlock due to a vital register getting
clobbered in _switch().
Change dependency to PPC32 and use r0 instead of r4 in _switch()
Fixes: e2fb9f544431 ("powerpc/32: Prepare for Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/540242f7d4573f7cdf1b3bf46bb35f743b2cd68f.1587124651.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61da50b76b62fd815aa82d853bf82bf4f69568f5 upstream.
Currently you can enable PPC_KUAP_DEBUG when PPC_KUAP is disabled,
even though the former has not effect without the latter.
Fix it so that PPC_KUAP_DEBUG can only be enabled when PPC_KUAP is
enabled, not when the platform could support KUAP (PPC_HAVE_KUAP).
Fixes: 890274c2dc4c ("powerpc/64s: Implement KUAP for Radix MMU")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200301111738.22497-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18cc7ac8a28e28cd005c2475f52576cfe10cabfb upstream.
This reverts commit 024ca329bfb9a948f76eaff3243e21b7e70182f2.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1ee35667e36a8efddee381df5fe495ad65f4d15c.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 492cc08bc16c44e2e587362ada3f6269dee2be22 upstream.
This reverts commit bed25ac0e2b6ab8f9aed2d20bc9c3a2037311800.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/eb0ec98fecdca9b79c1a3ac0c30c668b6973b193.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72d68197281e2ad313960504d10b0c41ff87fd55 upstream.
This reverts commit ae1cca3fa3478be92948dbbcd722390272032ade.
With setting up NR_PORTS to 16 to be able to use serial2 and higher
aliases and don't loose functionality which was intended by these changes.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/a94931b65ce0089f76fb1fe6b446a08731bff754.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91c9dfa25c7f95b543c280e0edf1fd8de6e90985 upstream.
This reverts commit 2088cfd882d0403609bdf426e9b24372fe1b8337.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/dac3898e3e32d963f357fb436ac9a7ac3cbcf933.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b6fd2dbbd649b89a3998528994665ded1e3fbf7f upstream.
This reverts commit 32cf21ac4edd6c0d5b9614368a83bcdc68acb031.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/46cd7f039db847c08baa6508edd7854f7c8ff80f.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8da1a3940da4b0e82848ec29b835486890bc9232 upstream.
This reverts commit ab262666018de6f4e206b021386b93ed0c164316.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/14a565fc1e14a5ec6cc6a6710deb878ae8305f22.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e01911b7cf7aa07a304a809eca1b11a4bd35859 upstream.
This reverts commit 5e9bd2d70ae7c00a95a22994abf1eef728649e64.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/310999ab5342f788a7bc1b0e68294d4f052cad07.1585905873.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3dc4db3662366306e54ddcbda4804acb1258e4ba upstream.
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f97250c21f0cf36434bf5b7ddf4377406534cd1 upstream.
The default control endpoint ep0 can return a STALL indicating the
device does not support the control transfer requests. This is called
a protocol stall and does not halt the endpoint.
xHC behaves a bit different. Its internal endpoint state will always
be halted on any stall, even if the device side of the endpiont is not
halted. So we do need to issue the reset endpoint command to clear the
xHC host intenal endpoint halt state, but should not request the HS hub
to clear the TT buffer unless device side of endpoint is halted.
Clearing the hub TT buffer at protocol stall caused ep0 to become
unresponsive for some FS/LS devices behind HS hubs, and class drivers
failed to set the interface due to timeout:
usb 1-2.1: 1:1: usb_set_interface failed (-110)
Fixes: ef513be0a905 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9fb08d617bfae5471d902112667d0eeb9dee3c4 upstream.
Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93ceaa808e8defc67ebca1396e2f42f812a2efc0 upstream.
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
invalid pointer
commit 0df9433fcae02215c8fd79690c134d535c7bb905 upstream.
Before this commit, typec_altmode_get_partner would return a
const struct typec_altmode * pointing to address 0x08 when
to_altmode(adev)->partner was NULL.
Add a check for to_altmode(adev)->partner being NULL to fix this.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206365
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1785972
Fixes: 5f54a85db5df ("usb: typec: Make sure an alt mode exist before getting its partner")
Cc: stable@vger.kernel.org
Signed-off-by: Naoki Kiryu <naonaokiryu2@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200422144345.43262-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 901789745a053286e0ced37960d44fa60267b940 upstream.
After PORT_RESET, the port is set to the appropriate
default_state. Ignore processing CC changes here as this
could cause the port to be switched into sink states
by default.
echo source > /sys/class/typec/port0/port_type
Before:
[ 154.528547] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms
[ 154.528560] CC1: 0 -> 0, CC2: 3 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 154.528564] state change PORT_RESET -> SNK_UNATTACHED
After:
[ 151.068814] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS]
[ 151.072440] CC1: 3 -> 0, CC2: 0 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 151.172117] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 151.172136] pending state change PORT_RESET_WAIT_OFF -> SRC_UNATTACHED @ 870 ms [rev3 NONE_AMS]
[ 152.060106] state change PORT_RESET_WAIT_OFF -> SRC_UNATTACHED [delayed 870 ms]
[ 152.060118] Start toggling
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200402215947.176577-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c2e54fbf1da5e5445a0ab132c862b02ccd8d230 upstream.
For userspace functions using OS Descriptors, if a function also supplies
Extended Property descriptors currently the counts and lengths stored in
the ms_os_descs_ext_prop_{count,name_len,data_len} variables are not
getting reset to 0 during an unbind or when the epfiles are closed. If
the same function is re-bound and the descriptors are re-written, this
results in those count/length variables to monotonically increase
causing the VLA allocation in _ffs_func_bind() to grow larger and larger
at each bind/unbind cycle and eventually fail to allocate.
Fix this by clearing the ms_os_descs_ext_prop count & lengths to 0 in
ffs_data_reset().
Fixes: f0175ab51993 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <ugoswami@codeaurora.org>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/20200402044521.9312-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49e0590e3a60e75b493e5df879e216e5073c7663 upstream.
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590fe ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c2760b78f90db874401d97e3c17829e2e36f400 upstream.
pci_driver.sriov_configure should return negative value on error and
number of enabled VFs on success. But now the driver returns 0 on
success. The sriov configure still works but will cause a warning
message:
XX VFs requested; only 0 enabled
This patch changes the return value accordingly.
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f6cc6093a729ede1ff5658b493237c42b82ba107 upstream.
A SCSI error handler and block runtime PM must not allocate
memory with GFP_KERNEL. Furthermore they must not wait for
tasks allocating memory with GFP_KERNEL.
That means that they cannot share a workqueue with arbitrary tasks.
Fix this for UAS using a private workqueue.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: f9dc024a2da1f ("uas: pre_reset and suspend: Fix a few races")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200415141750.811-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5963dec98dc52d52476390485f07a29c30c6a582 upstream.
Once a device is gone, the internal state does not matter anymore.
There is no need to spam the logs.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 326349f824619 ("uas: add dead request list")
Link: https://lore.kernel.org/r/20200415141750.811-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4e7279cd1d19f48f0af2a10ed020febaa9ac092 upstream.
Immediate submission in case of a babbling device can lead
to a busy loop. Introducing a delayed work.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0afccd7601514c4b83d8cc58c740089cc447051d upstream.
Suspend increments a counter, then kills the URBs,
then kills the scheduled work. The scheduled work, however,
may reschedule the URBs. Fix this by having the work
check the counter.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea81c3486442f4643fc9825a2bb1b430b829bccd upstream.
conf.listen_interval can sometimes be zero causing wake_up_count
to wrap around up to many beacons too late causing
CTRL-EVENT-BEACON-LOSS as in.
wpa_supplicant[795]: message repeated 45 times: [..CTRL-EVENT-BEACON-LOSS ]
Fixes: 43c93d9bf5e2 ("staging: vt6656: implement power saving code.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/fce47bb5-7ca6-7671-5094-5c6107302f2b@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b59f10b1d8fe8d50944f21f5d403df9303095a8 upstream.
The problem is that the group key was saved as VNT_KEY_DEFAULTKEY
was over written by the VNT_KEY_GROUP_ADDRESS index.
mac80211 could not clear the mac_addr in the default key.
The VNT_KEY_DEFAULTKEY is not necesscary so remove it and set as
VNT_KEY_GROUP_ADDRESS.
mac80211 can clear any key using vnt_mac_disable_keyentry.
Fixes: f9ef05ce13e4 ("staging: vt6656: Fix pairwise key for non station modes")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/da2f7e7f-1658-1320-6eee-0f55770ca391@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09057742af98a39ebffa27fac4f889dc873132de upstream.
The drivers TBTT counter is not synchronized with mac80211 timestamp.
Reorder the functions and use vnt_update_next_tbtt to do the final
synchronize.
Fixes: c15158797df6 ("staging: vt6656: implement TSF counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/375d0b25-e8bc-c8f7-9b10-6cc705d486ee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 664ba5180234593b4b8517530e8198bf2f7359e2 upstream.
vnt_set_bss_mode needs to be called on all changes to BSS_CHANGED_BASIC_RATES,
BSS_CHANGED_ERP_PREAMBLE and BSS_CHANGED_ERP_SLOT
Remove all other calls and vnt_update_ifs which is called in vnt_set_bss_mode.
Fixes an issue that preamble mode is not being updated correctly.
Fixes: c12603576e06 ("staging: vt6656: Only call vnt_set_bss_mode on basic rates change.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/44110801-6234-50d8-c583-9388f04b486c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0f8240bfc070033a4823b19883efd3d38c7735cc upstream.
mac80211/users control whether multicast is on or off don't enable it by default.
Fixes an issue when multicast/broadcast is always on allowing other beacons through
in power save.
Fixes: db8f37fa3355 ("staging: vt6656: mac80211 conversion: main_usb add functions...")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/2c24c33d-68c4-f343-bd62-105422418eac@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a98e7a80f95378c9ee0c644705e3b5aa54745f1 upstream.
Even if the actual screen size is bounded in vc_do_resize(), the unicode
buffer is still a little more than twice the size of the glyph buffer
and may exceed MAX_ORDER down the kmalloc() path. This can be triggered
from user space.
Since there is no point having a physically contiguous buffer here,
let's avoid the above issue as well as reducing pressure on high order
allocations by using vmalloc() instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003282214210.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2717769e204e83e65b8819c5e2ef3e5b6639b270 upstream.
The code in vc_do_resize() bounds the memory allocation size to avoid
exceeding MAX_ORDER down the kzalloc() call chain and generating a
runtime warning triggerable from user space. However, not only is it
unwise to use a literal value here, but MAX_ORDER may also be
configurable based on CONFIG_FORCE_MAX_ZONEORDER.
Let's use KMALLOC_MAX_SIZE instead.
Note that prior commit bb1107f7c605 ("mm, slab: make sure that
KMALLOC_MAX_SIZE will fit into MAX_ORDER") the KMALLOC_MAX_SIZE value
could not be relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003281702410.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 332e0e17ad49e084b7db670ef43b5eb59abd9e34 upstream.
comedi_open() invokes comedi_dev_get_from_minor(), which returns a
reference of the COMEDI device to "dev" with increased refcount.
When comedi_open() returns, "dev" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
comedi_open(). When "cfp" allocation is failed, the refcnt increased by
comedi_dev_get_from_minor() is not decreased, causing a refcnt leak.
Fix this issue by calling comedi_dev_put() on this error path when "cfp"
allocation is failed.
Fixes: 20f083c07565 ("staging: comedi: prepare support for per-file read and write subdevices")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/1587361459-83622-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed87d33ddbcd9a1c3b5ae87995da34e6f51a862c upstream.
The DT2815 analog output command is 16 bits wide, consisting of the
12-bit sample value in bits 15 to 4, the channel number in bits 3 to 1,
and a voltage or current selector in bit 0. Both bytes of the 16-bit
command need to be written in turn to a single 8-bit data register.
However, the driver currently only writes the low 8-bits. It is broken
and appears to have always been broken.
Electronic copies of the DT2815 User's Manual seem impossible to find
online, but looking at the source code, a best guess for the sequence
the driver intended to use to write the analog output command is as
follows:
1. Wait for the status register to read 0x00.
2. Write the low byte of the command to the data register.
3. Wait for the status register to read 0x80.
4. Write the high byte of the command to the data register.
Step 4 is missing from the driver. Add step 4 to (hopefully) fix the
driver.
Also add a "FIXME" comment about setting bit 0 of the low byte of the
command. Supposedly, it is used to choose between voltage output and
current output, but the current driver always sets it to 1.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200406142015.126982-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94c0b013c98583614e1ad911e8795ca36da34a85 upstream.
If {i,d}-cache-block-size is set and {i,d}-cache-line-size is not, use
the block-size value for both. Per the devicetree spec cache-line-size
is only needed if it differs from the block size.
Originally the code would fallback from block size to line size. An
error message was printed if both properties were missing.
Later the code was refactored to use clearer names and logic but it
inadvertently made line size a required property, meaning on systems
without a line size property we fall back to the default from the
cputable.
On powernv (OPAL) platforms, since the introduction of device tree CPU
features (5a61ef74f269 ("powerpc/64s: Support new device tree binding
for discovering CPU features")), that has led to the wrong value being
used, as the fallback value is incorrect for Power8/Power9 CPUs.
The incorrect values flow through to the VDSO and also to the sysconf
values, SC_LEVEL1_ICACHE_LINESIZE etc.
Fixes: bd067f83b084 ("powerpc/64: Fix naming of cache block vs. cache line")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Qian Cai <cai@lca.pw>
[mpe: Add even more detail to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200416221908.7886-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1baca8896ae18e12c45552a4c4ae2086aa7e02c upstream.
512a928affd5 ("ARM: imx: build v7_cpu_resume() unconditionally")
introduced an unintended linker error for i.MX6 configurations that have
ARM_CPU_SUSPEND=n which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE,
nor ARM_PSCI_FW are selected.
Fix this by having v7_cpu_resume() compiled only when cpu_resume() it
calls is available as well.
The C declaration for the function remains unguarded to avoid future code
inadvertently using a stub and introducing a regression to the bug the
original commit fixed.
Cc: <stable@vger.kernel.org>
Fixes: 512a928affd5 ("ARM: imx: build v7_cpu_resume() unconditionally")
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Tested-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0fe0781f29dd8ab618999e6bda33c782ebbdb109 upstream.
SMB2_open_init() expects a pre-initialised lease_key when opening a
file with a lease, so set pfid->lease_key prior to calling it in
open_shroot().
This issue was observed when performing some DFS failover tests and
the lease key was never randomly generated.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6d419f943318e2b903e380dfd52a8dda6db3021 upstream.
The function iwl_mvm_remove_inactive_tids() returns bool, so we
should just check "if (ret)", not "if (ret >= 0)" (which would
do nothing useful here). We obviously therefore cannot use the
return value of the function for the free_queue, we need to use
the queue (i) we're currently dealing with instead.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.9d862ed72535.I9e27ccc3ee3c8855fc13682592b571581925dfbd@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38af8d5a90a8c3b41ff0484855e24bd55b43ce9d upstream.
As this was not supposed to be enabled to begin with.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.53dbc3c6c36b.Idfe118546b92cc31548b2211472a5303c7de5909@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5b72e3bc4763152e24bf4b8333bae21cc526c56 upstream.
Due to some hardware issues, queue 31 isn't usable on devices that have
32 queues (7000, 8000, 9000 families), which is correctly reflected in
the configuration and TX queue initialization.
However, the firmware API and queue allocation code assumes that there
are 32 queues, and if something actually attempts to use #31 this leads
to a NULL-pointer dereference since it's not allocated.
Fix this by limiting to 31 in the IWL_MVM_DQA_MAX_DATA_QUEUE, and also
add some code to catch this earlier in the future, if the configuration
changes perhaps.
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.98a79be2db6a.I3a4af6b03b87a6bc18db9b1ff9a812f397bee1fc@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 290d5e4951832e39d10f4184610dbf09038f8483 upstream.
We reset statistics also in case that we didn't reassoc so in
this cases keep last beacon counter.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.1f9142751fbc.Ifbfd0f928a0a761110b8f4f2ca5483a61fb21131@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b98b33d5560a2d940f3b80f6768a6177bf3dfbc0 upstream.
The iwl_trans_pcie_dyn_txq_free() function only releases the frames
that may be left on the queue by calling iwl_pcie_gen2_txq_unmap(),
but doesn't actually free the DMA ring or byte-count tables for the
queue. This leads to pretty large memory leaks (at least before my
queue size improvements), in particular in monitor/sniffer mode on
channel hopping since this happens on every channel change.
This was also now more evident after the move to a DMA pool for the
byte count tables, showing messages such as
BUG iwlwifi:bc (...): Objects remaining in iwlwifi:bc on __kmem_cache_shutdown()
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=206811.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6b35ff91572f ("iwlwifi: pcie: introduce a000 TX queues management")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.f5f4c4193ec1.Id5feebc9b4318041913a9c89fc1378bb5454292c@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6221f1d9b63fed6260273e59a2b89ab30537a811 upstream.
Currently, after the forward channel connection goes away,
backchannel operations are causing soft lockups on the server
because call_transmit_status's SOFTCONN logic ignores ENOTCONN.
Such backchannel Calls are aggressively retried until the client
reconnects.
Backchannel Calls should use RPC_TASK_NOCONNECT rather than
RPC_TASK_SOFTCONN. If there is no forward connection, the server is
not capable of establishing a connection back to the client, thus
that backchannel request should fail before the server attempts to
send it. Commit 58255a4e3ce5 ("NFSD: NFSv4 callback client should
use RPC_TASK_SOFTCONN") was merged several years before
RPC_TASK_NOCONNECT was available.
Because setup_callback_client() explicitly sets NOPING, the NFSv4.0
callback connection depends on the first callback RPC to initiate
a connection to the client. Thus NFSv4.0 needs to continue to use
RPC_TASK_SOFTCONN.
Suggested-by: Trond Myklebust <trondmy@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cb5f3ea4654faf8c28b901266e960b1a4787b26 upstream.
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5d0 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebf1474745b4373fdde0fcf32d9d1f369b50b212 upstream.
snd_soc_dapm_kcontrol widget which is created by autodisable control
should contain correct on_val, mask and shift because it is set when the
widget is powered and changed value is applied on registers by following
code in dapm_seq_run_coalesced().
mask |= w->mask << w->shift;
if (w->power)
value |= w->on_val << w->shift;
else
value |= w->off_val << w->shift;
Shift on the mask in dapm_kcontrol_data_alloc() is removed to prevent
double shift.
And, on_val in dapm_kcontrol_set_value() is modified to get correct
value in the dapm_seq_run_coalesced().
Signed-off-by: Gyeongtaek Lee <gt82.lee@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/000001d61537$b212f620$1638e260$@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 763dafc520add02a1f4639b500c509acc0ea8e5b upstream.
Commit 756125289285 ("audit: always check the netlink payload length
in audit_receive_msg()") fixed a number of missing message length
checks, but forgot to check the length of userspace generated audit
records. The good news is that you need CAP_AUDIT_WRITE to submit
userspace audit records, which is generally only given to trusted
processes, so the impact should be limited.
Cc: stable@vger.kernel.org
Fixes: 756125289285 ("audit: always check the netlink payload length in audit_receive_msg()")
Reported-by: syzbot+49e69b4d71a420ceda3e@syzkaller.appspotmail.com
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61e713bdca3678e84815f2427f7a063fc353a1fc upstream.
Christof Meerwald <cmeerw@cmeerw.org> writes:
> Hi,
>
> this is probably related to commit
> 7a0cf094944e2540758b7f957eb6846d5126f535 (signal: Correct namespace
> fixups of si_pid and si_uid).
>
> With a 5.6.5 kernel I am seeing SIGCHLD signals that don't include a
> properly set si_pid field - this seems to happen for multi-threaded
> child processes.
>
> A simple test program (based on the sample from the signalfd man page):
>
> #include <sys/signalfd.h>
> #include <signal.h>
> #include <unistd.h>
> #include <spawn.h>
> #include <stdlib.h>
> #include <stdio.h>
>
> #define handle_error(msg) \
> do { perror(msg); exit(EXIT_FAILURE); } while (0)
>
> int main(int argc, char *argv[])
> {
> sigset_t mask;
> int sfd;
> struct signalfd_siginfo fdsi;
> ssize_t s;
>
> sigemptyset(&mask);
> sigaddset(&mask, SIGCHLD);
>
> if (sigprocmask(SIG_BLOCK, &mask, NULL) == -1)
> handle_error("sigprocmask");
>
> pid_t chldpid;
> char *chldargv[] = { "./sfdclient", NULL };
> posix_spawn(&chldpid, "./sfdclient", NULL, NULL, chldargv, NULL);
>
> sfd = signalfd(-1, &mask, 0);
> if (sfd == -1)
> handle_error("signalfd");
>
> for (;;) {
> s = read(sfd, &fdsi, sizeof(struct signalfd_siginfo));
> if (s != sizeof(struct signalfd_siginfo))
> handle_error("read");
>
> if (fdsi.ssi_signo == SIGCHLD) {
> printf("Got SIGCHLD %d %d %d %d\n",
> fdsi.ssi_status, fdsi.ssi_code,
> fdsi.ssi_uid, fdsi.ssi_pid);
> return 0;
> } else {
> printf("Read unexpected signal\n");
> }
> }
> }
>
>
> and a multi-threaded client to test with:
>
> #include <unistd.h>
> #include <pthread.h>
>
> void *f(void *arg)
> {
> sleep(100);
> }
>
> int main()
> {
> pthread_t t[8];
>
> for (int i = 0; i != 8; ++i)
> {
> pthread_create(&t[i], NULL, f, NULL);
> }
> }
>
> I tried to do a bit of debugging and what seems to be happening is
> that
>
> /* From an ancestor pid namespace? */
> if (!task_pid_nr_ns(current, task_active_pid_ns(t))) {
>
> fails inside task_pid_nr_ns because the check for "pid_alive" fails.
>
> This code seems to be called from do_notify_parent and there we
> actually have "tsk != current" (I am assuming both are threads of the
> current process?)
I instrumented the code with a warning and received the following backtrace:
> WARNING: CPU: 0 PID: 777 at kernel/pid.c:501 __task_pid_nr_ns.cold.6+0xc/0x15
> Modules linked in:
> CPU: 0 PID: 777 Comm: sfdclient Not tainted 5.7.0-rc1userns+ #2924
> Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
> RIP: 0010:__task_pid_nr_ns.cold.6+0xc/0x15
> Code: ff 66 90 48 83 ec 08 89 7c 24 04 48 8d 7e 08 48 8d 74 24 04 e8 9a b6 44 00 48 83 c4 08 c3 48 c7 c7 59 9f ac 82 e8 c2 c4 04 00 <0f> 0b e9 3fd
> RSP: 0018:ffffc9000042fbf8 EFLAGS: 00010046
> RAX: 000000000000000c RBX: 0000000000000000 RCX: ffffc9000042faf4
> RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff81193d29
> RBP: ffffc9000042fc18 R08: 0000000000000000 R09: 0000000000000001
> R10: 000000100f938416 R11: 0000000000000309 R12: ffff8880b941c140
> R13: 0000000000000000 R14: 0000000000000000 R15: ffff8880b941c140
> FS: 0000000000000000(0000) GS:ffff8880bca00000(0000) knlGS:0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> CR2: 00007f2e8c0a32e0 CR3: 0000000002e10000 CR4: 00000000000006f0
> Call Trace:
> send_signal+0x1c8/0x310
> do_notify_parent+0x50f/0x550
> release_task.part.21+0x4fd/0x620
> do_exit+0x6f6/0xaf0
> do_group_exit+0x42/0xb0
> get_signal+0x13b/0xbb0
> do_signal+0x2b/0x670
> ? __audit_syscall_exit+0x24d/0x2b0
> ? rcu_read_lock_sched_held+0x4d/0x60
> ? kfree+0x24c/0x2b0
> do_syscall_64+0x176/0x640
> ? trace_hardirqs_off_thunk+0x1a/0x1c
> entry_SYSCALL_64_after_hwframe+0x49/0xb3
The immediate problem is as Christof noticed that "pid_alive(current) == false".
This happens because do_notify_parent is called from the last thread to exit
in a process after that thread has been reaped.
The bigger issue is that do_notify_parent can be called from any
process that manages to wait on a thread of a multi-threaded process
from wait_task_zombie. So any logic based upon current for
do_notify_parent is just nonsense, as current can be pretty much
anything.
So change do_notify_parent to call __send_signal directly.
Inspecting the code it appears this problem has existed since the pid
namespace support started handling this case in 2.6.30. This fix only
backports to 7a0cf094944e ("signal: Correct namespace fixups of si_pid and si_uid")
where the problem logic was moved out of __send_signal and into send_signal.
Cc: stable@vger.kernel.org
Fixes: 6588c1e3ff01 ("signals: SI_USER: Masquerade si_pid when crossing pid ns boundary")
Ref: 921cf9f63089 ("signals: protect cinit from unblocked SIG_DFL signals")
Link: https://lore.kernel.org/lkml/20200419201336.GI22017@edge.cmeerw.net/
Reported-by: Christof Meerwald <cmeerw@cmeerw.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94f9c8c3c404ee1f7aaff81ad4f24aec4e34a78b upstream.
Cyril Roelandt reports that his JMicron JMS566 USB-SATA bridge fails
to handle WRITE commands with the FUA bit set, even though it claims
to support FUA. (Oddly enough, a later version of the same bridge,
version 2.03 as opposed to 1.14, doesn't claim to support FUA. Also
oddly, the bridge _does_ support FUA when using the UAS transport
instead of the Bulk-Only transport -- but this device was blacklisted
for uas in commit bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron
SATA enclosure") for apparently unrelated reasons.)
This patch adds a usb-storage unusual_devs entry with the BROKEN_FUA
flag. This allows the bridge to work properly with usb-storage.
Reported-and-tested-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221613110.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7127d24372bf23675a36edc64d092dc7fd92ebe8 upstream.
init_r_port can access pc104 array out of bounds. pc104 is a 2D array
defined to have 4 members. Each member has 8 submembers.
* we can have more than 4 (PCI) boards, i.e. [board] can be OOB
* line is not modulo-ed by anything, so the first line on the second
board can be 4, on the 3rd 12 or alike (depending on previously
registered boards). It's zero only on the first line of the first
board. So even [line] can be OOB, quite soon (with the 2nd registered
board already).
This code is broken for ages, so just avoid the OOB accesses and don't
try to fix it as we would need to find out the correct line number. Use
the default: RS232, if we are out.
Generally, if anyone needs to set the interface types, a module parameter
is past the last thing that should be used for this purpose. The
parameters' description says it's for ISA cards anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20200417105959.15201-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a9fc42b86c06120744555fea43fdcabe297c656 upstream.
If there is a lot(more then 16) of virtio-console devices
or virtio_console module is reloaded
- buffers 'vtermnos' and 'cons_ops' are overflowed.
In older kernels it overruns spinlock which leads to kernel freezing:
https://bugzilla.redhat.com/show_bug.cgi?id=1786239
To reproduce the issue, you can try simple script that
loads/unloads module. Something like this:
while [ 1 ]
do
modprobe virtio_console
sleep 2
modprobe -r virtio_console
sleep 2
done
Description of problem:
Guest get 'Call Trace' when loading module "virtio_console"
and unloading it frequently - clearly reproduced on kernel-4.18.0:
[ 81.498208] ------------[ cut here ]------------
[ 81.499263] pvqspinlock: lock 0xffffffff92080020 has corrupted value 0xc0774ca0!
[ 81.501000] WARNING: CPU: 0 PID: 785 at kernel/locking/qspinlock_paravirt.h:500 __pv_queued_spin_unlock_slowpath+0xc0/0xd0
[ 81.503173] Modules linked in: virtio_console fuse xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nft_counter nf_nat_tftp nft_objref nf_conntrack_tftp tun bridge stp llc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nf_tables_set nft_chain_nat_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 nft_chain_route_ipv6 nft_chain_nat_ipv4 nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack nft_chain_route_ipv4 ip6_tables nft_compat ip_set nf_tables nfnetlink sunrpc bochs_drm drm_vram_helper ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm i2c_piix4 pcspkr crct10dif_pclmul crc32_pclmul joydev ghash_clmulni_intel ip_tables xfs libcrc32c sd_mod sg ata_generic ata_piix virtio_net libata crc32c_intel net_failover failover serio_raw virtio_scsi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: virtio_console]
[ 81.517019] CPU: 0 PID: 785 Comm: kworker/0:2 Kdump: loaded Not tainted 4.18.0-167.el8.x86_64 #1
[ 81.518639] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014
[ 81.520205] Workqueue: events control_work_handler [virtio_console]
[ 81.521354] RIP: 0010:__pv_queued_spin_unlock_slowpath+0xc0/0xd0
[ 81.522450] Code: 07 00 48 63 7a 10 e8 bf 64 f5 ff 66 90 c3 8b 05 e6 cf d6 01 85 c0 74 01 c3 8b 17 48 89 fe 48 c7 c7 38 4b 29 91 e8 3a 6c fa ff <0f> 0b c3 0f 0b 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 48
[ 81.525830] RSP: 0018:ffffb51a01ffbd70 EFLAGS: 00010282
[ 81.526798] RAX: 0000000000000000 RBX: 0000000000000010 RCX: 0000000000000000
[ 81.528110] RDX: ffff9e66f1826480 RSI: ffff9e66f1816a08 RDI: ffff9e66f1816a08
[ 81.529437] RBP: ffffffff9153ff10 R08: 000000000000026c R09: 0000000000000053
[ 81.530732] R10: 0000000000000000 R11: ffffb51a01ffbc18 R12: ffff9e66cd682200
[ 81.532133] R13: ffffffff9153ff10 R14: ffff9e6685569500 R15: ffff9e66cd682000
[ 81.533442] FS: 0000000000000000(0000) GS:ffff9e66f1800000(0000) knlGS:0000000000000000
[ 81.534914] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 81.535971] CR2: 00005624c55b14d0 CR3: 00000003a023c000 CR4: 00000000003406f0
[ 81.537283] Call Trace:
[ 81.537763] __raw_callee_save___pv_queued_spin_unlock_slowpath+0x11/0x20
[ 81.539011] .slowpath+0x9/0xe
[ 81.539585] hvc_alloc+0x25e/0x300
[ 81.540237] init_port_console+0x28/0x100 [virtio_console]
[ 81.541251] handle_control_message.constprop.27+0x1c4/0x310 [virtio_console]
[ 81.542546] control_work_handler+0x70/0x10c [virtio_console]
[ 81.543601] process_one_work+0x1a7/0x3b0
[ 81.544356] worker_thread+0x30/0x390
[ 81.545025] ? create_worker+0x1a0/0x1a0
[ 81.545749] kthread+0x112/0x130
[ 81.546358] ? kthread_flush_work_fn+0x10/0x10
[ 81.547183] ret_from_fork+0x22/0x40
[ 81.547842] ---[ end trace aa97649bd16c8655 ]---
[ 83.546539] general protection fault: 0000 [#1] SMP NOPTI
[ 83.547422] CPU: 5 PID: 3225 Comm: modprobe Kdump: loaded Tainted: G W --------- - - 4.18.0-167.el8.x86_64 #1
[ 83.549191] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014
[ 83.550544] RIP: 0010:__pv_queued_spin_lock_slowpath+0x19a/0x2a0
[ 83.551504] Code: c4 c1 ea 12 41 be 01 00 00 00 4c 8d 6d 14 41 83 e4 03 8d 42 ff 49 c1 e4 05 48 98 49 81 c4 40 a5 02 00 4c 03 24 c5 60 48 34 91 <49> 89 2c 24 b8 00 80 00 00 eb 15 84 c0 75 0a 41 0f b6 54 24 14 84
[ 83.554449] RSP: 0018:ffffb51a0323fdb0 EFLAGS: 00010202
[ 83.555290] RAX: 000000000000301c RBX: ffffffff92080020 RCX: 0000000000000001
[ 83.556426] RDX: 000000000000301d RSI: 0000000000000000 RDI: 0000000000000000
[ 83.557556] RBP: ffff9e66f196a540 R08: 000000000000028a R09: ffff9e66d2757788
[ 83.558688] R10: 0000000000000000 R11: 0000000000000000 R12: 646e61725f770b07
[ 83.559821] R13: ffff9e66f196a554 R14: 0000000000000001 R15: 0000000000180000
[ 83.560958] FS: 00007fd5032e8740(0000) GS:ffff9e66f1940000(0000) knlGS:0000000000000000
[ 83.562233] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 83.563149] CR2: 00007fd5022b0da0 CR3: 000000038c334000 CR4: 00000000003406e0
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200414191503.3471783-1-andrew@daynix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Greg Kroah-Hartman
Christian Borntraeger
Arnd Bergmann
Christophe Leroy
Michael Ellerman
Michal Simek
Kazuhiro Fujita
Mathias Nyman
Naoki Kiryu
Badhri Jagan Sridharan
Udipto Goswami
Thinh Nguyen
Xu Yilun
Oliver Neukum
Malcolm Priestley
Nicolas Pitre
Xiyu Yang
Ian Abbott
Chris Packham
Ahmad Fatoum
Paulo Alcantara
Johannes Berg
Ilan Peer
Mordechay Goodstein
Chuck Lever
Gyeongtaek Lee
Paul Moore
Eric W. Biederman
Alan Stern
Jiri Slaby
Andrew Melnychenko