| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit 3612af783cf52c74a031a2f11b82247b2599d3cd upstream.
Marek reported that he saw an issue with the below snippet in that
timing measurements where off when loaded as unpriv while results
were reasonable when loaded as privileged:
[...]
uint64_t a = bpf_ktime_get_ns();
uint64_t b = bpf_ktime_get_ns();
uint64_t delta = b - a;
if ((int64_t)delta > 0) {
[...]
Turns out there is a bug where a corner case is missing in the fix
d3bd7413e0ca ("bpf: fix sanitation of alu op with pointer / scalar
type from different paths"), namely fixup_bpf_calls() only checks
whether aux has a non-zero alu_state, but it also needs to test for
the case of BPF_ALU_NON_POINTER since in both occasions we need to
skip the masking rewrite (as there is nothing to mask).
Fixes: d3bd7413e0ca ("bpf: fix sanitation of alu op with pointer / scalar type from different paths")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Reported-by: Arthur Fabre <afabre@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/netdev/CAJPywTJqP34cK20iLM5YmUMz9KXQOdu1-+BZrGMAGgLuBWz7fg@mail.gmail.com/T/
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a067cf823d9d8e50d41cfb618011c0d4a969c72 upstream.
Up to 4.12, __scsi_error_from_host_byte() would reset the host byte to
DID_OK for various cases including DID_NEXUS_FAILURE. Commit
2a842acab109 ("block: introduce new block status code type") replaced this
function with scsi_result_to_blk_status() and removed the host-byte
resetting code for the DID_NEXUS_FAILURE case. As the line
set_host_byte(cmd, DID_OK) was preserved for the other cases, I suppose
this was an editing mistake.
The fact that the host byte remains set after 4.13 is causing problems with
the sg_persist tool, which now returns success rather then exit status 24
when a RESERVATION CONFLICT error is encountered.
Fixes: 2a842acab109 "block: introduce new block status code type"
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f612acfae86af7ecad754ae6a46019be9da05b8e upstream.
syzkaller report this:
BUG: memory leak
unreferenced object 0xffffc9000488d000 (size 9195520):
comm "syz-executor.0", pid 2752, jiffies 4294787496 (age 18.757s)
hex dump (first 32 bytes):
ff ff ff ff ff ff ff ff a8 00 00 00 01 00 00 00 ................
02 00 00 00 00 00 00 00 80 a1 7a c1 ff ff ff ff ..........z.....
backtrace:
[<000000000863775c>] __vmalloc_node mm/vmalloc.c:1795 [inline]
[<000000000863775c>] __vmalloc_node_flags mm/vmalloc.c:1809 [inline]
[<000000000863775c>] vmalloc+0x8c/0xb0 mm/vmalloc.c:1831
[<000000003f668111>] kernel_read_file+0x58f/0x7d0 fs/exec.c:924
[<000000002385813f>] kernel_read_file_from_fd+0x49/0x80 fs/exec.c:993
[<0000000011953ff1>] __do_sys_finit_module+0x13b/0x2a0 kernel/module.c:3895
[<000000006f58491f>] do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
[<00000000ee78baf4>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<00000000241f889b>] 0xffffffffffffffff
It should goto 'out_free' lable to free allocated buf while kernel_read
fails.
Fixes: 39d637af5aa7 ("vfs: forbid write access when reading a file into memory")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thibaut Sautereau <thibaut@sautereau.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4f5627f7eeecde1bb6b646d8c0907b96dc2b2a6 upstream.
With commit e16337622016 ("Bluetooth: Handle bt_accept_enqueue() socket
atomically") lock_sock[_nested]() is used to acquire the socket lock
before manipulating the socket. lock_sock[_nested]() may block, which
is problematic since bt_accept_enqueue() can be called in bottom half
context (e.g. from rfcomm_connect_ind()):
[<ffffff80080d81ec>] __might_sleep+0x4c/0x80
[<ffffff800876c7b0>] lock_sock_nested+0x24/0x58
[<ffffff8000d7c27c>] bt_accept_enqueue+0x48/0xd4 [bluetooth]
[<ffffff8000e67d8c>] rfcomm_connect_ind+0x190/0x218 [rfcomm]
Add a parameter to bt_accept_enqueue() to indicate whether the
function is called from BH context, and acquire the socket lock
with bh_lock_sock_nested() if that's the case.
Also adapt all callers of bt_accept_enqueue() to pass the new
parameter:
- l2cap_sock_new_connection_cb()
- uses lock_sock() to lock the parent socket => process context
- rfcomm_connect_ind()
- acquires the parent socket lock with bh_lock_sock() => BH
context
- __sco_chan_add()
- called from sco_chan_add(), which is called from sco_connect().
parent is NULL, hence bt_accept_enqueue() isn't called in this
code path and we can ignore it
- also called from sco_conn_ready(). uses bh_lock_sock() to acquire
the parent lock => BH context
Fixes: e16337622016 ("Bluetooth: Handle bt_accept_enqueue() socket atomically")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00df214b1faae520880cc5c57e206f21239ef741 upstream.
Realtek bluetooth may not work after reboot:
[ 12.446130] Bluetooth: hci0: RTL: rtl: unknown IC info, lmp subver a99e, hci rev 826c, hci ver 0008
This is a regression introduced by commit 26503ad25de8 ("Bluetooth:
btrtl: split the device initialization into smaller parts"). The new
logic errors out early when no matching IC info can be found, in this
case it means the firmware is already loaded.
So let's assume the firmware is already loaded when we can't find
matching IC info, like the old logic did.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201921
Fixes: 26503ad25de8 ("Bluetooth: btrtl: split the device initialization into smaller parts")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 344c0152d878922365464b7140c74c2a5e073d99 upstream.
commit a6a9be9270c87 ("selftests: firmware: return Kselftest Skip code
for skipped tests") by Shuah modified failures to return the special
error code of $ksft_skip (4). We have a corner case issue where we
*do* want to verify_reqs().
Cc: <stable@vger.kernel.org> # >= 4.18
Fixes: a6a9be9270c87 ("selftests: firmware: return Kselftest Skip code for for skipped tests")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b0b644b9aa2de5032db0f468fddca091d0b7b90 upstream.
Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
Fixes: cf5276ce7867 ("USB: serial: cp210x: Adding GPIO support for CP2105")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82f844c22588bf47132c82faeda50b6db473162c upstream.
Make sure the receiver is powered (and booted) before enabling the
wakeup interrupt to avoid spurious interrupts due to a floating input.
Similarly, disable the interrupt before powering off on probe errors and
on unbind.
Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers")
Cc: stable <stable@vger.kernel.org> # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d90b88fd3653f1fb66ecc6571b860d5a5749fa56 upstream.
Stack unwinding is implemented incorrectly in xtensa get_wchan: instead
of extracting a0 and a1 registers from the spill location under the
stack pointer it extracts a word pointed to by the stack pointer and
subtracts 4 or 3 from it.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3d6a18d7d351cbcc9b33dbedf710e65f8ce1595 upstream.
wake_up_locked() may but does not have to be called with interrupts
disabled. Since the fuse filesystem calls wake_up_locked() without
disabling interrupts aio_poll_wake() may be called with interrupts
enabled. Since the kioctx.ctx_lock may be acquired from IRQ context,
all code that acquires that lock from thread context must disable
interrupts. Hence change the spin_trylock() call in aio_poll_wake()
into a spin_trylock_irqsave() call. This patch fixes the following
lockdep complaint:
=====================================================
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc4-next-20190131 #23 Not tainted
-----------------------------------------------------
syz-executor2/13779 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
0000000098ac1230 (&fiq->waitq){+.+.}, at: spin_lock include/linux/spinlock.h:329 [inline]
0000000098ac1230 (&fiq->waitq){+.+.}, at: aio_poll fs/aio.c:1772 [inline]
0000000098ac1230 (&fiq->waitq){+.+.}, at: __io_submit_one fs/aio.c:1875 [inline]
0000000098ac1230 (&fiq->waitq){+.+.}, at: io_submit_one+0xedf/0x1cf0 fs/aio.c:1908
and this task is already holding:
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: spin_lock_irq include/linux/spinlock.h:354 [inline]
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: aio_poll fs/aio.c:1771 [inline]
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: __io_submit_one fs/aio.c:1875 [inline]
000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: io_submit_one+0xeb6/0x1cf0 fs/aio.c:1908
which would create a new lock dependency:
(&(&ctx->ctx_lock)->rlock){..-.} -> (&fiq->waitq){+.+.}
but this new dependency connects a SOFTIRQ-irq-safe lock:
(&(&ctx->ctx_lock)->rlock){..-.}
... which became SOFTIRQ-irq-safe at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock_irq include/linux/spinlock_api_smp.h:128 [inline]
_raw_spin_lock_irq+0x60/0x80 kernel/locking/spinlock.c:160
spin_lock_irq include/linux/spinlock.h:354 [inline]
free_ioctx_users+0x2d/0x4a0 fs/aio.c:610
percpu_ref_put_many include/linux/percpu-refcount.h:285 [inline]
percpu_ref_put include/linux/percpu-refcount.h:301 [inline]
percpu_ref_call_confirm_rcu lib/percpu-refcount.c:123 [inline]
percpu_ref_switch_to_atomic_rcu+0x3e7/0x520 lib/percpu-refcount.c:158
__rcu_reclaim kernel/rcu/rcu.h:240 [inline]
rcu_do_batch kernel/rcu/tree.c:2486 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2799 [inline]
rcu_core+0x928/0x1390 kernel/rcu/tree.c:2780
__do_softirq+0x266/0x95a kernel/softirq.c:292
run_ksoftirqd kernel/softirq.c:654 [inline]
run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646
smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164
kthread+0x357/0x430 kernel/kthread.c:247
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
to a SOFTIRQ-irq-unsafe lock:
(&fiq->waitq){+.+.}
... which became SOFTIRQ-irq-unsafe at:
...
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
fuse_send_init fs/fuse/inode.c:989 [inline]
fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
mount_nodev+0x68/0x110 fs/super.c:1392
fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
vfs_get_tree+0x123/0x450 fs/super.c:1481
do_new_mount fs/namespace.c:2610 [inline]
do_mount+0x1436/0x2c40 fs/namespace.c:2932
ksys_mount+0xdb/0x150 fs/namespace.c:3148
__do_sys_mount fs/namespace.c:3162 [inline]
__se_sys_mount fs/namespace.c:3159 [inline]
__x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&fiq->waitq);
local_irq_disable();
lock(&(&ctx->ctx_lock)->rlock);
lock(&fiq->waitq);
<Interrupt>
lock(&(&ctx->ctx_lock)->rlock);
*** DEADLOCK ***
1 lock held by syz-executor2/13779:
#0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: spin_lock_irq include/linux/spinlock.h:354 [inline]
#0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: aio_poll fs/aio.c:1771 [inline]
#0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: __io_submit_one fs/aio.c:1875 [inline]
#0: 000000003c46111c (&(&ctx->ctx_lock)->rlock){..-.}, at: io_submit_one+0xeb6/0x1cf0 fs/aio.c:1908
the dependencies between SOFTIRQ-irq-safe lock and the holding lock:
-> (&(&ctx->ctx_lock)->rlock){..-.} {
IN-SOFTIRQ-W at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock_irq include/linux/spinlock_api_smp.h:128 [inline]
_raw_spin_lock_irq+0x60/0x80 kernel/locking/spinlock.c:160
spin_lock_irq include/linux/spinlock.h:354 [inline]
free_ioctx_users+0x2d/0x4a0 fs/aio.c:610
percpu_ref_put_many include/linux/percpu-refcount.h:285 [inline]
percpu_ref_put include/linux/percpu-refcount.h:301 [inline]
percpu_ref_call_confirm_rcu lib/percpu-refcount.c:123 [inline]
percpu_ref_switch_to_atomic_rcu+0x3e7/0x520 lib/percpu-refcount.c:158
__rcu_reclaim kernel/rcu/rcu.h:240 [inline]
rcu_do_batch kernel/rcu/tree.c:2486 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2799 [inline]
rcu_core+0x928/0x1390 kernel/rcu/tree.c:2780
__do_softirq+0x266/0x95a kernel/softirq.c:292
run_ksoftirqd kernel/softirq.c:654 [inline]
run_ksoftirqd+0x8e/0x110 kernel/softirq.c:646
smpboot_thread_fn+0x6ab/0xa10 kernel/smpboot.c:164
kthread+0x357/0x430 kernel/kthread.c:247
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
INITIAL USE at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock_irq include/linux/spinlock_api_smp.h:128 [inline]
_raw_spin_lock_irq+0x60/0x80 kernel/locking/spinlock.c:160
spin_lock_irq include/linux/spinlock.h:354 [inline]
__do_sys_io_cancel fs/aio.c:2052 [inline]
__se_sys_io_cancel fs/aio.c:2035 [inline]
__x64_sys_io_cancel+0xd5/0x5a0 fs/aio.c:2035
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
}
... key at: [<ffffffff8a574140>] __key.52370+0x0/0x40
... acquired at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
aio_poll fs/aio.c:1772 [inline]
__io_submit_one fs/aio.c:1875 [inline]
io_submit_one+0xedf/0x1cf0 fs/aio.c:1908
__do_sys_io_submit fs/aio.c:1953 [inline]
__se_sys_io_submit fs/aio.c:1923 [inline]
__x64_sys_io_submit+0x1bd/0x580 fs/aio.c:1923
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
the dependencies between the lock to be acquired
and SOFTIRQ-irq-unsafe lock:
-> (&fiq->waitq){+.+.} {
HARDIRQ-ON-W at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
fuse_send_init fs/fuse/inode.c:989 [inline]
fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
mount_nodev+0x68/0x110 fs/super.c:1392
fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
vfs_get_tree+0x123/0x450 fs/super.c:1481
do_new_mount fs/namespace.c:2610 [inline]
do_mount+0x1436/0x2c40 fs/namespace.c:2932
ksys_mount+0xdb/0x150 fs/namespace.c:3148
__do_sys_mount fs/namespace.c:3162 [inline]
__se_sys_mount fs/namespace.c:3159 [inline]
__x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
SOFTIRQ-ON-W at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
fuse_send_init fs/fuse/inode.c:989 [inline]
fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
mount_nodev+0x68/0x110 fs/super.c:1392
fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
vfs_get_tree+0x123/0x450 fs/super.c:1481
do_new_mount fs/namespace.c:2610 [inline]
do_mount+0x1436/0x2c40 fs/namespace.c:2932
ksys_mount+0xdb/0x150 fs/namespace.c:3148
__do_sys_mount fs/namespace.c:3162 [inline]
__se_sys_mount fs/namespace.c:3159 [inline]
__x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
INITIAL USE at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
flush_bg_queue+0x1f3/0x3c0 fs/fuse/dev.c:415
fuse_request_queue_background+0x2d1/0x580 fs/fuse/dev.c:676
fuse_request_send_background+0x58/0x120 fs/fuse/dev.c:687
fuse_send_init fs/fuse/inode.c:989 [inline]
fuse_fill_super+0x13bb/0x1730 fs/fuse/inode.c:1214
mount_nodev+0x68/0x110 fs/super.c:1392
fuse_mount+0x2d/0x40 fs/fuse/inode.c:1239
legacy_get_tree+0xf2/0x200 fs/fs_context.c:590
vfs_get_tree+0x123/0x450 fs/super.c:1481
do_new_mount fs/namespace.c:2610 [inline]
do_mount+0x1436/0x2c40 fs/namespace.c:2932
ksys_mount+0xdb/0x150 fs/namespace.c:3148
__do_sys_mount fs/namespace.c:3162 [inline]
__se_sys_mount fs/namespace.c:3159 [inline]
__x64_sys_mount+0xbe/0x150 fs/namespace.c:3159
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
}
... key at: [<ffffffff8a60dec0>] __key.43450+0x0/0x40
... acquired at:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
aio_poll fs/aio.c:1772 [inline]
__io_submit_one fs/aio.c:1875 [inline]
io_submit_one+0xedf/0x1cf0 fs/aio.c:1908
__do_sys_io_submit fs/aio.c:1953 [inline]
__se_sys_io_submit fs/aio.c:1923 [inline]
__x64_sys_io_submit+0x1bd/0x580 fs/aio.c:1923
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
stack backtrace:
CPU: 0 PID: 13779 Comm: syz-executor2 Not tainted 5.0.0-rc4-next-20190131 #23
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_bad_irq_dependency kernel/locking/lockdep.c:1573 [inline]
check_usage.cold+0x60f/0x940 kernel/locking/lockdep.c:1605
check_irq_usage kernel/locking/lockdep.c:1650 [inline]
check_prev_add_irq kernel/locking/lockdep_states.h:8 [inline]
check_prev_add kernel/locking/lockdep.c:1860 [inline]
check_prevs_add kernel/locking/lockdep.c:1968 [inline]
validate_chain kernel/locking/lockdep.c:2339 [inline]
__lock_acquire+0x1f12/0x4790 kernel/locking/lockdep.c:3320
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:3826
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
aio_poll fs/aio.c:1772 [inline]
__io_submit_one fs/aio.c:1875 [inline]
io_submit_one+0xedf/0x1cf0 fs/aio.c:1908
__do_sys_io_submit fs/aio.c:1953 [inline]
__se_sys_io_submit fs/aio.c:1923 [inline]
__x64_sys_io_submit+0x1bd/0x580 fs/aio.c:1923
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Fixes: e8693bcfa0b4 ("aio: allow direct aio poll comletions for keyed wakeups") # v4.19
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
[ bvanassche: added a comment ]
Reluctantly-Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72faa7a773ca59336f3c889e878de81445c5a85c upstream.
The irq_pages is the number of pages for irq stack, but not the
order which is needed by __get_free_pages().
We can use get_order() to calculate the accurate order.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: fe8bd18ffea5 ("MIPS: Introduce irq_stack")
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7ac3c6ef5d8ce14b6381d52eb7adafdd6c8bb3c upstream.
IndexCard is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/char/applicom.c:418 ac_write() warn: potential spectre issue 'apbs' [r]
drivers/char/applicom.c:728 ac_ioctl() warn: potential spectre issue 'apbs' [r] (local cap)
Fix this by sanitizing IndexCard before using it to index apbs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8fde481ef3674ae5ad0dbfef4df18ff507c5675a upstream.
This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a072128d262d2b98d31626906a96700d1fc11eb upstream.
Then tracing syscall exit event it is extremely useful to filter exit
codes equal to some negative value, to react only to required errors.
But negative numbers does not work:
[root@snorch sys_exit_read]# echo "ret == -1" > filter
bash: echo: write error: Invalid argument
[root@snorch sys_exit_read]# cat filter
ret == -1
^
parse_error: Invalid value (did you forget quotes)?
Similar thing happens when setting triggers.
These is a regression in v4.17 introduced by the commit mentioned below,
testing without these commit shows no problem with negative numbers.
Link: http://lkml.kernel.org/r/20180823102534.7642-1-ptikhomirov@virtuozzo.com
Cc: stable@vger.kernel.org
Fixes: 80765597bc58 ("tracing: Rewrite filter logic to be simpler and faster")
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f913de3231e1d70a871135b38219da7810df218 upstream.
EFI systems do not necessarily provide a legacy ROM. If the ROM is missing
the memory is not mapped at all.
Trying to dereference values in the legacy ROM area leads to a crash on
Macbook Pro.
Only look for values in the legacy ROM area for non-EFI system.
Fixes: 3548e131ec6a ("x86/boot/compressed/64: Find a place for 32-bit trampoline")
Reported-by: Pitam Mitra <pitamm@gmail.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Bockjoo Kim <bockjoo@phys.ufl.edu>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190219075224.35058-1-kirill.shutemov@linux.intel.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202351
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0237199186e7a4aa5310741f0a6498a20c820fd7 upstream.
Some F17h models do not have CPB set in CPUID even though the CPU
supports it. Set the feature bit unconditionally on all F17h.
[ bp: Rewrite commit message and patch. ]
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sherry Hurwitz <sherry.hurwitz@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181120030018.5185-1-jiaxun.yang@flygoat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a3df633a3c92bb96b06552c3f828d7c267774379 ]
Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
Fixes: ee28bb56ac5b ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6191da98062d25276a3b88fb2a94dcbcfb3ea65d ]
when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:
# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.
Fixes: c749cdda9089 ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8f67c90ee9148eab3d2b4393c3cf76489b27f87c ]
After commit 4e8ddd7f1758 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:
# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.
Fixes: 4e8ddd7f1758 ("net: sched: don't release reference on action overwrite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ed8fe20205ac054bf585156709de3913d1890f30 ]
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d235c48b40d399328585a68f3f9bf7cc3062d586 ]
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a1fd1ad2552fad9e649eeb85fd79301e2880a886 ]
ip_route_input_rcu expects the original ingress device (e.g., for
proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
so dev needs to be saved prior to calling it. This was the behavior prior
to the listify changes.
Fixes: 5fa12739a53d0 ("net: ipv4: listify ip_rcv_finish")
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit be48220edd48ca0d569782992840488a52373a24 ]
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e3818541b49fb88650ba339d33cc53e4095da5b3 ]
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b6e9e5df4ecf100f6a10ab2ade8e46d47a4b9779 ]
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3da1ed7ac398f34fff1694017a07054d69c5f5c5 ]
Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9ef6b42ad6fd7929dd1b6092cb02014e382c6a91 ]
Add __icmp_send function having ip_options struct parameter
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ecef67cb10db7b83b3b71c61dbb29aa070ab0112 ]
Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 99e87f56b48f490fb16b6e0f74691c1e664dea95 ]
Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:
"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"
That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a2288d4e355992d369c50c45d017a85f6061ff71 ]
Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.
In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 71828b2240692cec0e68b8d867bc00e1745e7fae ]
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bfd07f3dd4f111b884d7922b37eb239280f83d8c ]
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ff7b11aa481f682e0e9711abfeb7d03f5cd612bf ]
Commit 9060cb719e61 ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat(). However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:
- base_sock_release
- bnep_sock_release
- cmtp_sock_release
- data_sock_release
- dn_release
- hci_sock_release
- hidp_sock_release
- iucv_sock_release
- l2cap_sock_release
- llcp_sock_release
- llc_ui_release
- rawsock_release
- rfcomm_sock_release
- sco_sock_release
- svc_release
- vcc_release
- x25_release
Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().
Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:
#include <pthread.h>
#include <stdlib.h>
#include <sys/socket.h>
#include <unistd.h>
pthread_t t;
volatile int fd;
void *close_thread(void *arg)
{
for (;;) {
usleep(rand() % 100);
close(fd);
}
}
int main()
{
pthread_create(&t, NULL, close_thread, NULL);
for (;;) {
fd = socket(rand() % 50, rand() % 11, 0);
fchownat(fd, "", 1000, 1000, 0x1000);
close(fd);
}
}
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 07f12b26e21ab359261bf75cfcb424fdc7daeb6d ]
If register_netdev() is failed to register sitn->fb_tunnel_dev,
it will go to err_reg_dev and forget to free netdev(sitn->fb_tunnel_dev).
BUG: memory leak
unreferenced object 0xffff888378daad00 (size 512):
comm "syz-executor.1", pid 4006, jiffies 4295121142 (age 16.115s)
hex dump (first 32 bytes):
00 e6 ed c0 83 88 ff ff 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000d6dcb63e>] kvmalloc include/linux/mm.h:577 [inline]
[<00000000d6dcb63e>] kvzalloc include/linux/mm.h:585 [inline]
[<00000000d6dcb63e>] netif_alloc_netdev_queues net/core/dev.c:8380 [inline]
[<00000000d6dcb63e>] alloc_netdev_mqs+0x600/0xcc0 net/core/dev.c:8970
[<00000000867e172f>] sit_init_net+0x295/0xa40 net/ipv6/sit.c:1848
[<00000000871019fa>] ops_init+0xad/0x3e0 net/core/net_namespace.c:129
[<00000000319507f6>] setup_net+0x2ba/0x690 net/core/net_namespace.c:314
[<0000000087db4f96>] copy_net_ns+0x1dc/0x330 net/core/net_namespace.c:437
[<0000000057efc651>] create_new_namespaces+0x382/0x730 kernel/nsproxy.c:107
[<00000000676f83de>] copy_namespaces+0x2ed/0x3d0 kernel/nsproxy.c:165
[<0000000030b74bac>] copy_process.part.27+0x231e/0x6db0 kernel/fork.c:1919
[<00000000fff78746>] copy_process kernel/fork.c:1713 [inline]
[<00000000fff78746>] _do_fork+0x1bc/0xe90 kernel/fork.c:2224
[<000000001c2e0d1c>] do_syscall_64+0xc8/0x580 arch/x86/entry/common.c:290
[<00000000ec48bd44>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<0000000039acff8a>] 0xffffffffffffffff
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d25ed413d5e51644e18f66e34eec049f17a7abcb ]
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 232ba3a51cc224b339c7114888ed7f0d4d95695e ]
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 58bdd544e2933a21a51eecf17c3f5f94038261b5 ]
KASAN report this:
BUG: KASAN: null-ptr-deref in nfc_llcp_build_gb+0x37f/0x540 [nfc]
Read of size 3 at addr 0000000000000000 by task syz-executor.0/5401
CPU: 0 PID: 5401 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
kasan_report+0x171/0x18d mm/kasan/report.c:321
memcpy+0x1f/0x50 mm/kasan/common.c:130
nfc_llcp_build_gb+0x37f/0x540 [nfc]
nfc_llcp_register_device+0x6eb/0xb50 [nfc]
nfc_register_device+0x50/0x1d0 [nfc]
nfcsim_device_new+0x394/0x67d [nfcsim]
? 0xffffffffc1080000
nfcsim_init+0x6b/0x1000 [nfcsim]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f9cb79dcc58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000280 RDI: 0000000000000003
RBP: 00007f9cb79dcc70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9cb79dd6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
nfc_llcp_build_tlv will return NULL on fails, caller should check it,
otherwise will trigger a NULL dereference.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: eda21f16a5ed ("NFC: Set MIU and RW values from CONNECT and CC LLCP frames")
Fixes: d646960f7986 ("NFC: Initial LLCP support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5845f706388a4cde0f6b80f9e5d33527e942b7d9 ]
It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly
[10258690.371129] kernel BUG at net/core/skbuff.c:4028!
[10258690.371748] invalid opcode: 0000 [#1] SMP PTI
[10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G W 5.0.0-rc6 #2
[10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
[10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
[10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
[10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
[10258690.372094] FS: 0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
[10258690.372094] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
[10258690.372094] Call Trace:
[10258690.372094] <IRQ>
[10258690.372094] skb_to_sgvec+0x11/0x40
[10258690.372094] start_xmit+0x38c/0x520 [virtio_net]
[10258690.372094] dev_hard_start_xmit+0x9b/0x200
[10258690.372094] sch_direct_xmit+0xff/0x260
[10258690.372094] __qdisc_run+0x15e/0x4e0
[10258690.372094] net_tx_action+0x137/0x210
[10258690.372094] __do_softirq+0xd6/0x2a9
[10258690.372094] irq_exit+0xde/0xf0
[10258690.372094] smp_apic_timer_interrupt+0x74/0x140
[10258690.372094] apic_timer_interrupt+0xf/0x20
[10258690.372094] </IRQ>
In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.
Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.
To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.
Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
Signed-off-by: Sheng Lan <lansheng@huawei.com>
Reported-by: Qin Ji <jiqin.ji@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5578de4834fe0f2a34fedc7374be691443396d1f ]
There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both
errors are embarassingly simple, and the fixes are straightforward.
As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: Jann Horn <jannh@google.com>
Fixes: 446fda4f2682 ("[NetLabel]: CIPSOv4 engine")
Fixes: 3faa8f982f95 ("netlabel: Move bitmap manipulation functions to the NetLabel core.")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6e46e2d821bb22b285ae8187959096b65d063b0d ]
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a6da21bb0eae459a375d5bd48baed821d14301d0 ]
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.
Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c394900 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 90490ef7269906423a1c1b917fc24be8b1602658 ]
It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.
This fix corrects the problem by properly marking the end of
a multi descriptor transmission.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5e1a99eae84999a2536f50a0beaf5d5262337f40 ]
For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.
Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.
v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: eacb9384a3fe ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bf48648d650db1146b75b9bd358502431e86cf4f ]
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cf1c9ccba7308e48a68fa77f476287d9d614e4c7 ]
When IPv6 is compiled but disabled at runtime, geneve_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.
Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.
This is the same fix as what commit d074bf960044 ("vxlan: correctly handle
ipv6.disable module parameter") is doing for vxlan.
Note there's also commit c0a47e44c098 ("geneve: should not call rt6_lookup()
when ipv6 was disabled") which fixes a similar issue but for regular
tunnels, while this patch is needed for metadata based tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2b3c6885386020b1b9d92d45e8349637e27d1f66 ]
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e63208915a8d7590d0a6218dadb2a6a00ac705a ]
Fix regression bug introduced in
commit 365ad353c256 ("tipc: reduce risk of user starvation during link
congestion")
Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 692c31bd4054212312396b1d303bffab2c5b93a7 ]
When team is used in loadbalance mode a BPF filter can be used to
provide a hash which will determine the Tx port.
When the netdev is later unregistered the filter is not freed which
results in memory leaks [1].
Fix by freeing the program and the corresponding filter when
unregistering the netdev.
[1]
unreferenced object 0xffff8881dbc47cc8 (size 16):
comm "teamd", pid 3068, jiffies 4294997779 (age 438.247s)
hex dump (first 16 bytes):
a3 00 6b 6b 6b 6b 6b 6b 88 a5 82 e1 81 88 ff ff ..kkkkkk........
backtrace:
[<000000008a3b47e3>] team_nl_cmd_options_set+0x88f/0x11b0
[<00000000c4f4f27e>] genl_family_rcv_msg+0x78f/0x1080
[<00000000610ef838>] genl_rcv_msg+0xca/0x170
[<00000000a281df93>] netlink_rcv_skb+0x132/0x380
[<000000004d9448a2>] genl_rcv+0x29/0x40
[<000000000321b2f4>] netlink_unicast+0x4c0/0x690
[<000000008c25dffb>] netlink_sendmsg+0x929/0xe10
[<00000000068298c5>] sock_sendmsg+0xc8/0x110
[<0000000082a61ff0>] ___sys_sendmsg+0x77a/0x8f0
[<00000000663ae29d>] __sys_sendmsg+0xf7/0x250
[<0000000027c5f11a>] do_syscall_64+0x14d/0x610
[<000000006cfbc8d3>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<00000000e23197e2>] 0xffffffffffffffff
unreferenced object 0xffff8881e182a588 (size 2048):
comm "teamd", pid 3068, jiffies 4294997780 (age 438.247s)
hex dump (first 32 bytes):
20 00 00 00 02 00 00 00 30 00 00 00 28 f0 ff ff .......0...(...
07 00 00 00 00 00 00 00 28 00 00 00 00 00 00 00 ........(.......
backtrace:
[<000000002daf01fb>] lb_bpf_func_set+0x45c/0x6d0
[<000000008a3b47e3>] team_nl_cmd_options_set+0x88f/0x11b0
[<00000000c4f4f27e>] genl_family_rcv_msg+0x78f/0x1080
[<00000000610ef838>] genl_rcv_msg+0xca/0x170
[<00000000a281df93>] netlink_rcv_skb+0x132/0x380
[<000000004d9448a2>] genl_rcv+0x29/0x40
[<000000000321b2f4>] netlink_unicast+0x4c0/0x690
[<000000008c25dffb>] netlink_sendmsg+0x929/0xe10
[<00000000068298c5>] sock_sendmsg+0xc8/0x110
[<0000000082a61ff0>] ___sys_sendmsg+0x77a/0x8f0
[<00000000663ae29d>] __sys_sendmsg+0xf7/0x250
[<0000000027c5f11a>] do_syscall_64+0x14d/0x610
[<000000006cfbc8d3>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<00000000e23197e2>] 0xffffffffffffffff
Fixes: 01d7f30a9f96 ("team: add loadbalance mode")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b33b7cd6fd86478dd2890a9abeb6f036aa01fdf7 ]
Some sky2 chips fire IRQ after S3, before the driver is fully resumed:
[ 686.804877] do_IRQ: 1.37 No irq handler for vector
This is likely a platform bug that device isn't fully quiesced during
S3. Use MSI-X, maskable MSI or INTx can prevent this issue from
happening.
Since MSI-X and maskable MSI are not supported by this device, fallback
to use INTx on affected platforms.
BugLink: https://bugs.launchpad.net/bugs/1807259
BugLink: https://bugs.launchpad.net/bugs/1809843
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Greg Kroah-Hartman
Daniel Borkmann
Martin Wilck
YueHaibing
Matthias Kaehlcke
Kai-Heng Feng
Luis Chamberlain
Karoly Pados
Johan Hovold
Max Filippov
Bart Van Assche
Liu Xiang
Gustavo A. R. Silva
Balaji Manoharan
Pavel Tikhomirov
Kirill A. Shutemov
Jiaxun Yang
Vlad Buslov
Davide Caratti
Heiner Kallweit
Maxime Chevallier
David Ahern
Nazarov Sergey
Timur Celik
Igor Druzhinin
Tung Nguyen
Eric Biggers
Mao Wenan
Rajasingh Thavamani
Sheng Lan
Paul Moore
Andrew Lunn
Bryan Whitehead
Hangbin Liu
Haiyang Zhang
Jiri Benc
Michael Chan
Erik Hugne
Ido Schimmel