diff options
Diffstat (limited to 'arch/arm/boot/dts/motorola-mapphone-common.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/motorola-mapphone-common.dtsi | 43 |
1 files changed, 40 insertions, 3 deletions
diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi index 9067e0ef4240..06fbffa81636 100644 --- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi +++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi @@ -367,6 +367,8 @@ }; &mmc3 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; vmmc-supply = <&wl12xx_vmmc>; /* uart2_tx.sdmmc3_dat1 pad as wakeirq */ interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH @@ -472,6 +474,37 @@ >; }; + /* + * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3 + * for gpio_100, but the internal pull makes wlan flakey on some + * devices. Off mode value should be tested if we have off mode working + * later on. + */ + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + /* 0x4a10008e gpmc_wait2.gpio_100 d23 */ + OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3) + + /* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */ + OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */ + OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */ + OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1) + + /* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */ + OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */ + OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1) + + /* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */ + OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1) + >; + }; + /* gpmc_ncs0.gpio_50 */ poweroff_gpio: pinmux_poweroff_pins { pinctrl-single,pins = < @@ -690,14 +723,18 @@ }; /* - * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for - * uart1 wakeirq. + * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149 + * for wake-up events for both the USB PHY and the UART. We can use gpio_149 + * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we + * have gpio_149 trigger before the UART transfer starts. */ &uart1 { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins>; interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH - &omap4_pmx_core 0xfc>; + &omap4_pmx_core 0x110>; + uart-has-rtscts; + current-speed = <115200>; }; &uart3 { |