/dts-v1/;
/include/ "zynq7-base.dtsi"
/ {
	model = "ze7000";

	chosen {
		bootargs = "console=ttyPS0,115200 earlyprintk";
		linux,stdout-path = &ps7_uart_0;
	} ;

	aliases {
		serial0 = &ps7_uart_0;
	} ;

	ps7_ddr_0: memory@0 {
		device_type = "memory";
		reg = < 0x0 0x20000000 >;
	} ;

	ps7_axi_interconnect_0: amba@0 {

		ps7_smc_0: smc@0xe000e000 {
			#address-cells = <1>;
			#size-cells = <1>;
			arm,addr25 = <0x0>;
			arm,nor-chip-sel0 = <0x0>;
			arm,nor-chip-sel1 = <0x0>;
			arm,sram-chip-sel0 = <0x0>;
			arm,sram-chip-sel1 = <0x0>;
			clock-names = "memclk", "aclk";
			clocks = <&clkc 11>, <&clkc 44>;
			compatible = "arm,pl353-smc-r2p1";
			interrupt-parent = <&ps7_scugic_0>;
			interrupts = <0 18 4>;
			ranges ;
			reg = <0xe000e000 0x1000>;
			ps7_nand_0: ps7-nand@e1000000 {
				compatible = "arm,pl353-nand-r2p1";
				reg = <0xe1000000 0x1000000>;

				/* Timings are set by FSBL, linux should not change them.
					Look out for DONT_TOUCH_SMC_NAND_TIMING_WIDTH in pl353-smc.c */

				#address-cells = <0x1>;
				#size-cells = <0x1>;

				partition@nand-linux {
					label = "nand-linux";
					reg = <0x0 0x500000>;
				};

				partition@nand-device-tree {
					label = "nand-device-tree";
					reg = <0x500000 0x100000>;
				};

				partition@nand-rootfs {
					label = "nand-rootfs";
					reg = <0x600000 0x000000>;
				};
			};
		} ;

		ps7_ethernet_0: ps7-ethernet@e000b000 {
			phy-handle = <&phy0>;
			phy-mode = "";
			mdio {
				phy0: phy@3 {
					compatible = "micrel,ksz9031";
					device_type = "ethernet-phy";
					reg = <0x3>;
				};
			} ;
		} ;

		ps7_ethernet_1: ps7-ethernet@e000c000 {
			phy-handle = <&phy1 &phy2 &phy3 &phy4>;
			phy-mode = "";

			mdio {
				#address-cells = <1>;
				#size-cells = <0>;

				phy1: phy@7 {
					compatible = "marvell,88e1118";
					device_type = "ethernet-phy";
					reg = <7>;
				};

				phy2: phy@6 {
					compatible = "marvell,88e1118";
					device_type = "ethernet-phy";
					reg = <6>;
				};

				phy3: phy@5 {
					compatible = "marvell,88e1118";
					device_type = "ethernet-phy";
					reg = <5>;
				};

				phy4: phy@4 {
					compatible = "marvell,88e1118";
					device_type = "ethernet-phy";
					reg = <4>;
				};

			} ;
		} ;

		ps7_gpio_0: ps7-gpio@e000a000 {
			gpio-mask-high = <0xc0000>;
			gpio-mask-low = <0xfe81>;
		} ;

		ps7_sd_0: ps7-sdio@e0100000 {
			clock-frequency = <125000000>;
			xlnx,sdio-clk-freq-hz = <0x3f93e10>;
		} ;

		ps7_i2c_0: ps7-i2c@e0004000 {

			board_eeprom@54 {
				compatible = "at,24c64";
				reg = <0x54>;
			} ;

			rtc@6F {
				compatible = "isl12022";
				reg = <0x6F>;
			} ;
		} ;

		/* Disabled Devices */
		ps7_uart_1: serial@e0001000 { compatible = "invalid"; };
		ps7_sd_1: ps7-sdio@e0101000 { compatible = "invalid"; };
		ps7_wdt_0: ps7-wdt@f8005000 { compatible = "invalid"; };
		ps7_can_0: ps7-can@e0008000 { compatible = "invalid"; };
		ps7_can_1: ps7-can@e0009000 { compatible = "invalid"; };
		ps7_usb_1: ps7-usb@e0003000 { compatible = "invalid"; };
		ps7_dma_ns: ps7-dma@f8004000 { compatible =" invalid"; };
		ps7_i2c_1: ps7-i2c@e0005000 { compatible = "invalid"; };
		ps7_qspi_0: ps7-qspi@e000d000 { compatible = "invalid"; };
		ps7_qspi_linear_0: ps7-qspi-linear@fc000000 { compatible = "invalid"; };
		ps7_spi_0: ps7-spi@e0006000  { compatible = "invalid"; };
		ps7_spi_1: ps7-spi@e0007000  { compatible = "invalid"; };
	} ;
} ;