This README file contains information on building the meta-emenlow BSP layer using any of the supported machine configurations, and booting the images contained in the /binary directory. The 'eMenlow' platform consists of the Intel Atom Z5xx processor, plus the Intel US15W System Controller Hub. Further information on the platform supported by this BSP can be found here: http://www.portwell.com/products/detail.asp?CUSTCHAR1=WEBS-2120 Information on all IntelĀ® embedded platforms can be found here: http://www.intel.com/p/en_US/embedded/hwsw/hardware If you're only interested in booting the images in the /binary directory of a BSP tarball you've downloaded, there's nothing special to do - the appropriate images are already in the /binary directory depending on which BSP tarball you downloaded. Please see the corresponding sections below for details. Yocto Project Compatible ======================== This BSP is compatible with the Yocto Project as per the requirements listed here: https://www.yoctoproject.org/webform/yocto-project-compatible-registration Dependencies ============ This layer depends on: URI: git://git.openembedded.org/bitbake branch: master URI: git://git.openembedded.org/openembedded-core layers: meta branch: master URI: git://git.yoctoproject.org/meta-intel layers: intel branch: master Patches ======= Please submit any patches against this BSP to the meta-intel mailing list (meta-intel@yoctoproject.org) and cc: the maintainer: Maintainer: Nitin A Kamble Please see the meta-intel/MAINTAINERS file for more details. Table of Contents ================= I. Building the meta-emenlow BSP layer II. Booting the images in /binary I. Building the meta-emenlow BSP layer ======================================= In order to build an image with BSP support for a given release, you need to download the corresponding BSP tarball from the 'Board Support Package (BSP) Downloads' page of the Yocto Project website. Having done that, and assuming you extracted the BSP tarball contents at the top-level of your yocto build tree, you can build an emenlow image by adding the location of the meta-emenlow layer to bblayers.conf, along with the meta-intel layer itself (to access common metadata shared between BSPs) e.g.: yocto/meta-intel \ yocto/meta-intel/meta-emenlow \ The meta-emenlow layer contains support for emenlow-noemgd machine configuration. The previously supported emenlow machine with the proprietary EMGD graphics driver has been retired. The 'emenlow-noemgd' machine configuration uses the open source 'gma500' kernel DRM driver along with the 'modesetting' X driver. To enable the layer add the following to the local.conf file: MACHINE ?= "emenlow-noemgd" You should then be able to build an emenlow image as such: $ source oe-init-build-env $ bitbake core-image-sato At the end of a successful build, you should have a live image that you can boot from a USB flash drive (see instructions on how to do that below, in the section 'Booting the images from /binary'). As an alternative to downloading the BSP tarball, you can also work directly from the meta-intel git repository. For each BSP in the 'meta-intel' repository, there are multiple branches, one corresponding to each major release starting with 'laverne' (0.90), in addition to the latest code which tracks the current master (note that not all BSPs are present in every release). Instead of extracting a BSP tarball at the top level of your yocto build tree, you can equivalently check out the appropriate branch from the meta-intel repository at the same location. II. Booting the images in /binary ================================= This BSP contains bootable live images, which can be used to directly boot Yocto off of a USB flash drive. Under Linux, insert a USB flash drive. Assuming the USB flash drive takes device /dev/sdf, use dd to copy the live image to it. For example: # dd if=core-image-sato-emenlow-noemgd.hddimg of=/dev/sdf # sync # eject /dev/sdf This should give you a bootable USB flash device. Insert the device into a bootable USB socket on the target, and power on. This should result in a system booted to the Sato graphical desktop. If you want a terminal, use the arrows at the top of the UI to move to different pages of available applications, one of which is named 'Terminal'. Clicking that should give you a root terminal. If you want to ssh into the system, you can use the root terminal to ifconfig the IP address and use that to ssh in. The root password is empty, so to log in type 'root' for the user name and hit 'Enter' at the Password prompt: and you should be in. ---- If you find you're getting corrupt images on the USB (it doesn't show the syslinux boot: prompt, or the boot: prompt contains strange characters), try doing this first: # dd if=/dev/zero of=/dev/sdf bs=1M count=512