1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Raspberry Pi voltage sensor driver
*
* Based on firmware/raspberrypi.c by Noralf Trønnes
*
* Copyright (C) 2018 Stefan Wahren <stefan.wahren@i2se.com>
*/
#include <linux/device.h>
#include <linux/err.h>
#include <linux/hwmon.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/workqueue.h>
#include <soc/bcm2835/raspberrypi-firmware.h>
/*
* This section defines some rate limited logging that prevent
* repeated messages at much lower Hz than the default kernel settings.
* It's usually 5s, this is 5 minutes.
* Burst 3 means you may get three messages 'quickly', before
* the ratelimiting kicks in.
*/
#define LOCAL_RATELIMIT_INTERVAL (5 * 60 * HZ)
#define LOCAL_RATELIMIT_BURST 3
#ifdef CONFIG_PRINTK
#define printk_ratelimited_local(fmt, ...) \
({ \
static DEFINE_RATELIMIT_STATE(_rs, \
LOCAL_RATELIMIT_INTERVAL, \
LOCAL_RATELIMIT_BURST); \
\
if (__ratelimit(&_rs)) \
printk(fmt, ##__VA_ARGS__); \
})
#else
#define printk_ratelimited_local(fmt, ...) \
no_printk(fmt, ##__VA_ARGS__)
#endif
#define pr_crit_ratelimited_local(fmt, ...) \
printk_ratelimited_local(KERN_CRIT pr_fmt(fmt), ##__VA_ARGS__)
#define pr_info_ratelimited_local(fmt, ...) \
printk_ratelimited_local(KERN_INFO pr_fmt(fmt), ##__VA_ARGS__)
#define UNDERVOLTAGE_STICKY_BIT BIT(16)
struct rpi_hwmon_data {
struct device *hwmon_dev;
struct rpi_firmware *fw;
u32 last_throttled;
struct delayed_work get_values_poll_work;
};
static void rpi_firmware_get_throttled(struct rpi_hwmon_data *data)
{
u32 new_uv, old_uv, value;
int ret;
/* Request firmware to clear sticky bits */
value = 0xffff;
ret = rpi_firmware_property(data->fw, RPI_FIRMWARE_GET_THROTTLED,
&value, sizeof(value));
if (ret) {
dev_err_once(data->hwmon_dev, "Failed to get throttled (%d)\n",
ret);
return;
}
new_uv = value & UNDERVOLTAGE_STICKY_BIT;
old_uv = data->last_throttled & UNDERVOLTAGE_STICKY_BIT;
data->last_throttled = value;
if (new_uv == old_uv)
return;
if (new_uv) {
pr_crit_ratelimited_local("Under-voltage detected! (0x%08x)\n",
value);
} else {
pr_info_ratelimited_local("Voltage normalised (0x%08x)\n",
value);
}
sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm");
}
static void get_values_poll(struct work_struct *work)
{
struct rpi_hwmon_data *data;
data = container_of(work, struct rpi_hwmon_data,
get_values_poll_work.work);
rpi_firmware_get_throttled(data);
/*
* We can't run faster than the sticky shift (100ms) since we get
* flipping in the sticky bits that are cleared.
*/
schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
}
static int rpi_read(struct device *dev, enum hwmon_sensor_types type,
u32 attr, int channel, long *val)
{
struct rpi_hwmon_data *data = dev_get_drvdata(dev);
*val = !!(data->last_throttled & UNDERVOLTAGE_STICKY_BIT);
return 0;
}
static umode_t rpi_is_visible(const void *_data, enum hwmon_sensor_types type,
u32 attr, int channel)
{
return 0444;
}
static const struct hwmon_channel_info *rpi_info[] = {
HWMON_CHANNEL_INFO(in,
HWMON_I_LCRIT_ALARM),
NULL
};
static const struct hwmon_ops rpi_hwmon_ops = {
.is_visible = rpi_is_visible,
.read = rpi_read,
};
static const struct hwmon_chip_info rpi_chip_info = {
.ops = &rpi_hwmon_ops,
.info = rpi_info,
};
static int rpi_hwmon_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct rpi_hwmon_data *data;
data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
/* Parent driver assure that firmware is correct */
data->fw = dev_get_drvdata(dev->parent);
data->hwmon_dev = devm_hwmon_device_register_with_info(dev, "rpi_volt",
data,
&rpi_chip_info,
NULL);
INIT_DELAYED_WORK(&data->get_values_poll_work, get_values_poll);
platform_set_drvdata(pdev, data);
if (!PTR_ERR_OR_ZERO(data->hwmon_dev))
schedule_delayed_work(&data->get_values_poll_work, 2 * HZ);
return PTR_ERR_OR_ZERO(data->hwmon_dev);
}
static int rpi_hwmon_remove(struct platform_device *pdev)
{
struct rpi_hwmon_data *data = platform_get_drvdata(pdev);
cancel_delayed_work_sync(&data->get_values_poll_work);
return 0;
}
static struct platform_driver rpi_hwmon_driver = {
.probe = rpi_hwmon_probe,
.remove = rpi_hwmon_remove,
.driver = {
.name = "raspberrypi-hwmon",
},
};
module_platform_driver(rpi_hwmon_driver);
MODULE_AUTHOR("Stefan Wahren <wahrenst@gmx.net>");
MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
MODULE_LICENSE("GPL v2");
MODULE_ALIAS("platform:raspberrypi-hwmon");
|
