1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-a", "brcm,bcm2835";
model = "Raspberry Pi Model A";
memory@0 {
device_type = "memory";
reg = <0 0x10000000>;
};
leds {
act {
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
&gpio {
/*
* Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
* RPI00021 sheet 02
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "SDA0",
"SCL0",
"SDA1",
"SCL1",
"GPIO_GCLK",
"CAM_GPIO1",
"LAN_RUN",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"NC", /* GPIO12 */
"NC", /* GPIO13 */
/* Serial port */
"TXD0",
"RXD0",
"STATUS_LED_N",
"GPIO17",
"GPIO18",
"NC", /* GPIO19 */
"NC", /* GPIO20 */
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"NC", /* GPIO26 */
"CAM_GPIO0",
/* Binary number representing build/revision */
"CONFIG0",
"CONFIG1",
"CONFIG2",
"CONFIG3",
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"NC", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"PWM0_OUT",
"NC", /* GPIO41 */
"NC", /* GPIO42 */
"NC", /* GPIO43 */
"NC", /* GPIO44 */
"PWM1_OUT",
"HDMI_HPD_P",
"SD_CARD_DET",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
/* I2S interface */
i2s_alt2: i2s_alt2 {
brcm,pins = <28 29 30 31>;
brcm,function = <BCM2835_FSEL_ALT2>;
};
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
status = "okay";
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
status = "okay";
};
&sdhost {
pinctrl-names = "default";
pinctrl-0 = <&sdhost_gpio48>;
bus-width = <4>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
/* i2c0 on camera/display connector is gpio 0&1. Not exposed on header.
* To avoid having to remap everything, map both ports to gpios 0&1
*/
&i2c0mux {
pinctrl-1 = <&i2c0_gpio0>;
};
|
