// SPDX-License-Identifier: GPL-2.0 // // Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver // // Author: Timur Tabi // // Copyright 2007-2010 Freescale Semiconductor, Inc. // // Some notes why imx-pcm-fiq is used instead of DMA on some boards: // // The i.MX SSI core has some nasty limitations in AC97 mode. While most // sane processor vendors have a FIFO per AC97 slot, the i.MX has only // one FIFO which combines all valid receive slots. We cannot even select // which slots we want to receive. The WM9712 with which this driver // was developed with always sends GPIO status data in slot 12 which // we receive in our (PCM-) data stream. The only chance we have is to // manually skip this data in the FIQ handler. With sampling rates different // from 48000Hz not every frame has valid receive data, so the ratio // between pcm data and GPIO status data changes. Our FIQ handler is not // able to handle this, hence this driver only works with 48000Hz sampling // rate. // Reading and writing AC97 registers is another challenge. The core // provides us status bits when the read register is updated with *another* // value. When we read the same register two times (and the register still // contains the same value) these status bits are not set. We work // around this by not polling these bits but only wait a fixed delay. #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "fsl_ssi.h" #include "imx-pcm.h" /* Define RX and TX to index ssi->regvals array; Can be 0 or 1 only */ #define RX 0 #define TX 1 /** * FSLSSI_I2S_FORMATS: audio formats supported by the SSI * * The SSI has a limitation in that the samples must be in the same byte * order as the host CPU. This is because when multiple bytes are written * to the STX register, the bytes and bits must be written in the same * order. The STX is a shift register, so all the bits need to be aligned * (bit-endianness must match byte-endianness). Processors typically write * the bits within a byte in the same order that the bytes of a word are * written in. So if the host CPU is big-endian, then only big-endian * samples will be written to STX properly. */ #ifdef __BIG_ENDIAN #define FSLSSI_I2S_FORMATS \ (SNDRV_PCM_FMTBIT_S8 | \ SNDRV_PCM_FMTBIT_S16_BE | \ SNDRV_PCM_FMTBIT_S18_3BE | \ SNDRV_PCM_FMTBIT_S20_3BE | \ SNDRV_PCM_FMTBIT_S24_3BE | \ SNDRV_PCM_FMTBIT_S24_BE) #else #define FSLSSI_I2S_FORMATS \ (SNDRV_PCM_FMTBIT_S8 | \ SNDRV_PCM_FMTBIT_S16_LE | \ SNDRV_PCM_FMTBIT_S18_3LE | \ SNDRV_PCM_FMTBIT_S20_3LE | \ SNDRV_PCM_FMTBIT_S24_3LE | \ SNDRV_PCM_FMTBIT_S24_LE) #endif /* * In AC97 mode, TXDIR bit is forced to 0 and TFDIR bit is forced to 1: * - SSI inputs external bit clock and outputs frame sync clock -- CBM_CFS * - Also have NB_NF to mark these two clocks will not be inverted */ #define FSLSSI_AC97_DAIFMT \ (SND_SOC_DAIFMT_AC97 | \ SND_SOC_DAIFMT_CBM_CFS | \ SND_SOC_DAIFMT_NB_NF) #define FSLSSI_SIER_DBG_RX_FLAGS \ (SSI_SIER_RFF0_EN | \ SSI_SIER_RLS_EN | \ SSI_SIER_RFS_EN | \ SSI_SIER_ROE0_EN | \ SSI_SIER_RFRC_EN) #define FSLSSI_SIER_DBG_TX_FLAGS \ (SSI_SIER_TFE0_EN | \ SSI_SIER_TLS_EN | \ SSI_SIER_TFS_EN | \ SSI_SIER_TUE0_EN | \ SSI_SIER_TFRC_EN) enum fsl_ssi_type { FSL_SSI_MCP8610, FSL_SSI_MX21, FSL_SSI_MX35, FSL_SSI_MX51, }; struct fsl_ssi_regvals { u32 sier; u32 srcr; u32 stcr; u32 scr; }; static bool fsl_ssi_readable_reg(struct device *dev, unsigned int reg) { switch (reg) { case REG_SSI_SACCEN: case REG_SSI_SACCDIS: return false; default: return true; } } static bool fsl_ssi_volatile_reg(struct device *dev, unsigned int reg) { switch (reg) { case REG_SSI_STX0: case REG_SSI_STX1: case REG_SSI_SRX0: case REG_SSI_SRX1: case REG_SSI_SISR: case REG_SSI_SFCSR: case REG_SSI_SACNT: case REG_SSI_SACADD: case REG_SSI_SACDAT: case REG_SSI_SATAG: case REG_SSI_SACCST: case REG_SSI_SOR: return true; default: return false; } } static bool fsl_ssi_precious_reg(struct device *dev, unsigned int reg) { switch (reg) { case REG_SSI_SRX0: case REG_SSI_SRX1: case REG_SSI_SISR: case REG_SSI_SACADD: case REG_SSI_SACDAT: case REG_SSI_SATAG: return true; default: return false; } } static bool fsl_ssi_writeable_reg(struct device *dev, unsigned int reg) { switch (reg) { case REG_SSI_SRX0: case REG_SSI_SRX1: case REG_SSI_SACCST: return false; default: return true; } } static const struct regmap_config fsl_ssi_regconfig = { .max_register = REG_SSI_SACCDIS, .reg_bits = 32, .val_bits = 32, .reg_stride = 4, .val_format_endian = REGMAP_ENDIAN_NATIVE, .num_reg_defaults_raw = REG_SSI_SACCDIS / sizeof(uint32_t) + 1, .readable_reg = fsl_ssi_readable_reg, .volatile_reg = fsl_ssi_volatile_reg, .precious_reg = fsl_ssi_precious_reg, .writeable_reg = fsl_ssi_writeable_reg, .cache_type = REGCACHE_FLAT, }; struct fsl_ssi_soc_data { bool imx; bool imx21regs; /* imx21-class SSI - no SACC{ST,EN,DIS} regs */ bool offline_config; u32 sisr_write_mask; }; /** * fsl_ssi: per-SSI private data * * @regs: Pointer to the regmap registers * @irq: IRQ of this SSI * @cpu_dai_drv: CPU DAI driver for this device * * @dai_fmt: DAI configuration this device is currently used with * @streams: Mask of current active streams: BIT(TX) and BIT(RX) * @i2s_net: I2S and Network mode configurations of SCR register * (this is the initial settings based on the DAI format) * @synchronous: Use synchronous mode - both of TX and RX use STCK and SFCK * @use_dma: DMA is used or FIQ with stream filter * @use_dual_fifo: DMA with support for dual FIFO mode * @has_ipg_clk_name: If "ipg" is in the clock name list of device tree * @fifo_depth: Depth of the SSI FIFOs * @slot_width: Width of each DAI slot * @slots: Number of slots * @regvals: Specific RX/TX register settings * * @clk: Clock source to access register * @baudclk: Clock source to generate bit and frame-sync clocks * @baudclk_streams: Active streams that are using baudclk * * @regcache_sfcsr: Cache sfcsr register value during suspend and resume * @regcache_sacnt: Cache sacnt register value during suspend and resume * * @dma_params_tx: DMA transmit parameters * @dma_params_rx: DMA receive parameters * @ssi_phys: physical address of the SSI registers * * @fiq_params: FIQ stream filtering parameters * * @card_pdev: Platform_device pointer to register a sound card for PowerPC or * to register a CODEC platform device for AC97 * @card_name: Platform_device name to register a sound card for PowerPC or * to register a CODEC platform device for AC97 * @card_idx: The index of SSI to register a sound card for PowerPC or * to register a CODEC platform device for AC97 * * @dbg_stats: Debugging statistics * * @soc: SoC specific data * @dev: Pointer to &pdev->dev * * @fifo_watermark: The FIFO watermark setting. Notifies DMA when there are * @fifo_watermark or fewer words in TX fifo or * @fifo_watermark or more empty words in RX fifo. * @dma_maxburst: Max number of words to transfer in one go. So far, * this is always the same as fifo_watermark. * * @ac97_reg_lock: Mutex lock to serialize AC97 register access operations */ struct fsl_ssi { struct regmap *regs; int irq; struct snd_soc_dai_driver cpu_dai_drv; unsigned int dai_fmt; u8 streams; u8 i2s_net; bool synchronous; bool use_dma; bool use_dual_fifo; bool has_ipg_clk_name; unsigned int fifo_depth; unsigned int slot_width; unsigned int slots; struct fsl_ssi_regvals regvals[2]; struct clk *clk; struct clk *baudclk; unsigned int baudclk_streams; u32 regcache_sfcsr; u32 regcache_sacnt; struct snd_dmaengine_dai_dma_data dma_params_tx; struct snd_dmaengine_dai_dma_data dma_params_rx; dma_addr_t ssi_phys; struct imx_pcm_fiq_params fiq_params; struct platform_device *card_pdev; char card_name[32]; u32 card_idx; struct fsl_ssi_dbg dbg_stats; const struct fsl_ssi_soc_data *soc; struct device *dev; u32 fifo_watermark; u32 dma_maxburst; struct mutex ac97_reg_lock; }; /* * SoC specific data * * Notes: * 1) SSI in earlier SoCS has critical bits in control registers that * cannot be changed after SSI starts running -- a software reset * (set SSIEN to 0) is required to change their values. So adding * an offline_config flag for these SoCs. * 2) SDMA is available since imx35. However, imx35 does not support * DMA bits changing when SSI is running, so set offline_config. * 3) imx51 and later versions support register configurations when * SSI is running (SSIEN); For these versions, DMA needs to be * configured before SSI sends DMA request to avoid an undefined * DMA request on the SDMA side. */ static struct fsl_ssi_soc_data fsl_ssi_mpc8610 = { .imx = false, .offline_config = true, .sisr_write_mask = SSI_SISR_RFRC | SSI_SISR_TFRC | SSI_SISR_ROE0 | SSI_SISR_ROE1 | SSI_SISR_TUE0 | SSI_SISR_TUE1, }; static struct fsl_ssi_soc_data fsl_ssi_imx21 = { .imx = true, .imx21regs = true, .offline_config = true, .sisr_write_mask = 0, }; static struct fsl_ssi_soc_data fsl_ssi_imx35 = { .imx = true, .offline_config = true, .sisr_write_mask = SSI_SISR_RFRC | SSI_SISR_TFRC | SSI_SISR_ROE0 | SSI_SISR_ROE1 | SSI_SISR_TUE0 | SSI_SISR_TUE1, }; static struct fsl_ssi_soc_data fsl_ssi_imx51 = { .imx = true, .offline_config = false, .sisr_write_mask = SSI_SISR_ROE0 | SSI_SISR_ROE1 | SSI_SISR_TUE0 | SSI_SISR_TUE1, }; static const struct of_device_id fsl_ssi_ids[] = { { .compatible = "fsl,mpc8610-ssi", .data = &fsl_ssi_mpc8610 }, { .compatible = "fsl,imx51-ssi", .data = &fsl_ssi_imx51 }, { .compatible = "fsl,imx35-ssi", .data = &fsl_ssi_imx35 }, { .compatible = "fsl,imx21-ssi", .data = &fsl_ssi_imx21 }, {} }; MODULE_DEVICE_TABLE(of, fsl_ssi_ids); static bool fsl_ssi_is_ac97(struct fsl_ssi *ssi) { return (ssi->dai_fmt & SND_SOC_DAIFMT_FORMAT_MASK) == SND_SOC_DAIFMT_AC97; } static bool fsl_ssi_is_i2s_master(struct fsl_ssi *ssi) { return (ssi->dai_fmt & SND_SOC_DAIFMT_MASTER_MASK) == SND_SOC_DAIFMT_CBS_CFS; } static bool fsl_ssi_is_i2s_cbm_cfs(struct fsl_ssi *ssi) { return (ssi->dai_fmt & SND_SOC_DAIFMT_MASTER_MASK) == SND_SOC_DAIFMT_CBM_CFS; } /** * Interrupt handler to gather states */ static irqreturn_t fsl_ssi_isr(int irq, void *dev_id) { struct fsl_ssi *ssi = dev_id; struct regmap *regs = ssi->regs; u32 sisr, sisr2; regmap_read(regs, REG_SSI_SISR, &sisr); sisr2 = sisr & ssi->soc->sisr_write_mask; /* Clear the bits that we set */ if (sisr2) regmap_write(regs, REG_SSI_SISR, sisr2); fsl_ssi_dbg_isr(&ssi->dbg_stats, sisr); return IRQ_HANDLED; } /** * Set SCR, SIER, STCR and SRCR registers with cached values in regvals * * Notes: * 1) For offline_config SoCs, enable all necessary bits of both streams * when 1st stream starts, even if the opposite stream will not start * 2) It also clears FIFO before setting regvals; SOR is safe to set online */ static void fsl_ssi_config_enable(struct fsl_ssi *ssi, bool tx) { struct fsl_ssi_regvals *vals = ssi->regvals; int dir = tx ? TX : RX; u32 sier, srcr, stcr; /* Clear dirty data in the FIFO; It also prevents channel slipping */ regmap_update_bits(ssi->regs, REG_SSI_SOR, SSI_SOR_xX_CLR(tx), SSI_SOR_xX_CLR(tx)); /* * On offline_config SoCs, SxCR and SIER are already configured when * the previous stream started. So skip all SxCR and SIER settings * to prevent online reconfigurations, then jump to set SCR directly */ if (ssi->soc->offline_config && ssi->streams) goto enable_scr; if (ssi->soc->offline_config) { /* * Online reconfiguration not supported, so enable all bits for * both streams at once to avoid necessity of reconfigurations */ srcr = vals[RX].srcr | vals[TX].srcr; stcr = vals[RX].stcr | vals[TX].stcr; sier = vals[RX].sier | vals[TX].sier; } else { /* Otherwise, only set bits for the current stream */ srcr = vals[dir].srcr; stcr = vals[dir].stcr; sier = vals[dir].sier; } /* Configure SRCR, STCR and SIER at once */ regmap_update_bits(ssi->regs, REG_SSI_SRCR, srcr, srcr); regmap_update_bits(ssi->regs, REG_SSI_STCR, stcr, stcr); regmap_update_bits(ssi->regs, REG_SSI_SIER, sier, sier); enable_scr: /* * Start DMA before setting TE to avoid FIFO underrun * which may cause a channel slip or a channel swap * * TODO: FIQ cases might also need this upon testing */ if (ssi->use_dma && tx) { int try = 100; u32 sfcsr; /* Enable SSI first to send TX DMA request */ regmap_update_bits(ssi->regs, REG_SSI_SCR, SSI_SCR_SSIEN, SSI_SCR_SSIEN); /* Busy wait until TX FIFO not empty -- DMA working */ do { regmap_read(ssi->regs, REG_SSI_SFCSR, &sfcsr); if (SSI_SFCSR_TFCNT0(sfcsr)) break; } while (--try); /* FIFO still empty -- something might be wrong */ if (!SSI_SFCSR_TFCNT0(sfcsr)) dev_warn(ssi->dev, "Timeout waiting TX FIFO filling\n"); } /* Enable all remaining bits in SCR */ regmap_update_bits(ssi->regs, REG_SSI_SCR, vals[dir].scr, vals[dir].scr); /* Log the enabled stream to the mask */ ssi->streams |= BIT(dir); } /** * Exclude bits that are used by the opposite stream * * When both streams are active, disabling some bits for the current stream * might break the other stream if these bits are used by it. * * @vals : regvals of the current stream * @avals: regvals of the opposite stream * @aactive: active state of the opposite stream * * 1) XOR vals and avals to get the differences if the other stream is active; * Otherwise, return current vals if the other stream is not active * 2) AND the result of 1) with the current vals */ #define _ssi_xor_shared_bits(vals, avals, aactive) \ ((vals) ^ ((avals) * (aactive))) #define ssi_excl_shared_bits(vals, avals, aactive) \ ((vals) & _ssi_xor_shared_bits(vals, avals, aactive)) /** * Unset SCR, SIER, STCR and SRCR registers with cached values in regvals * * Notes: * 1) For offline_config SoCs, to avoid online reconfigurations, disable all * bits of both streams at once when the last stream is abort to end * 2) It also clears FIFO after unsetting regvals; SOR is safe to set online */ static void fsl_ssi_config_disable(struct fsl_ssi *ssi, bool tx) { struct fsl_ssi_regvals *vals, *avals; u32 sier, srcr, stcr, scr; int adir = tx ? RX : TX; int dir = tx ? TX : RX; bool aactive; /* Check if the opposite stream is active */ aactive = ssi->streams & BIT(adir); vals = &ssi->regvals[dir]; /* Get regvals of the opposite stream to keep opposite stream safe */ avals = &ssi->regvals[adir]; /* * To keep the other stream safe, exclude shared bits between * both streams, and get safe bits to disable current stream */ scr = ssi_excl_shared_bits(vals->scr, avals->scr, aactive); /* Disable safe bits of SCR register for the current stream */ regmap_update_bits(ssi->regs, REG_SSI_SCR, scr, 0); /* Log the disabled stream to the mask */ ssi->streams &= ~BIT(dir); /* * On offline_config SoCs, if the other stream is active, skip * SxCR and SIER settings to prevent online reconfigurations */ if (ssi->soc->offline_config && aactive) goto fifo_clear; if (ssi->soc->offline_config) { /* Now there is only current stream active, disable all bits */ srcr = vals->srcr | avals->srcr; stcr = vals->stcr | avals->stcr; sier = vals->sier | avals->sier; } else { /* * To keep the other stream safe, exclude shared bits between * both streams, and get safe bits to disable current stream */ sier = ssi_excl_shared_bits(vals->sier, avals->sier, aactive); srcr = ssi_excl_shared_bits(vals->srcr, avals->srcr, aactive); stcr = ssi_excl_shared_bits(vals->stcr, avals->stcr, aactive); } /* Clear configurations of SRCR, STCR and SIER at once */ regmap_update_bits(ssi->regs, REG_SSI_SRCR, srcr, 0); regmap_update_bits(ssi->regs, REG_SSI_STCR, stcr, 0); regmap_update_bits(ssi->regs, REG_SSI_SIER, sier, 0); fifo_clear: /* Clear remaining data in the FIFO */ regmap_update_bits(ssi->regs, REG_SSI_SOR, SSI_SOR_xX_CLR(tx), SSI_SOR_xX_CLR(tx)); } static void fsl_ssi_tx_ac97_saccst_setup(struct fsl_ssi *ssi) { struct regmap *regs = ssi->regs; /* no SACC{ST,EN,DIS} regs on imx21-class SSI */ if (!ssi->soc->imx21regs) { /* Disable all channel slots */ regmap_write(regs, REG_SSI_SACCDIS, 0xff); /* Enable slots 3 & 4 -- PCM Playback Left & Right channels */ regmap_write(regs, REG_SSI_SACCEN, 0x300); } } /** * Cache critical bits of SIER, SRCR, STCR and SCR to later set them safely */ static void fsl_ssi_setup_regvals(struct fsl_ssi *ssi) { struct fsl_ssi_regvals *vals = ssi->regvals; vals[RX].sier = SSI_SIER_RFF0_EN | FSLSSI_SIER_DBG_RX_FLAGS; vals[RX].srcr = SSI_SRCR_RFEN0; vals[RX].scr = SSI_SCR_SSIEN | SSI_SCR_RE; vals[TX].sier = SSI_SIER_TFE0_EN | FSLSSI_SIER_DBG_TX_FLAGS; vals[TX].stcr = SSI_STCR_TFEN0; vals[TX].scr = SSI_SCR_SSIEN | SSI_SCR_TE; /* AC97 has already enabled SSIEN, RE and TE, so ignore them */ if (fsl_ssi_is_ac97(ssi)) vals[RX].scr = vals[TX].scr = 0; if (ssi->use_dual_fifo) { vals[RX].srcr |= SSI_SRCR_RFEN1; vals[TX].stcr |= SSI_STCR_TFEN1; } if (ssi->use_dma) { vals[RX].sier |= SSI_SIER_RDMAE; vals[TX].sier |= SSI_SIER_TDMAE; } else { vals[RX].sier |= SSI_SIER_RIE; vals[TX].sier |= SSI_SIER_TIE; } } static void fsl_ssi_setup_ac97(struct fsl_ssi *ssi) { struct regmap *regs = ssi->regs; /* Setup the clock control register */ regmap_write(regs, REG_SSI_STCCR, SSI_SxCCR_WL(17) | SSI_SxCCR_DC(13)); regmap_write(regs, REG_SSI_SRCCR, SSI_SxCCR_WL(17) | SSI_SxCCR_DC(13)); /* Enable AC97 mode and startup the SSI */ regmap_write(regs, REG_SSI_SACNT, SSI_SACNT_AC97EN | SSI_SACNT_FV); /* AC97 has to communicate with codec before starting a stream */ regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_SSIEN | SSI_SCR_TE | SSI_SCR_RE, SSI_SCR_SSIEN | SSI_SCR_TE | SSI_SCR_RE); regmap_write(regs, REG_SSI_SOR, SSI_SOR_WAIT(3)); } static int fsl_ssi_startup(struct snd_pcm_substream *substream, struct snd_soc_dai *dai) { struct snd_soc_pcm_runtime *rtd = substream->private_data; struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(rtd->cpu_dai); int ret; ret = clk_prepare_enable(ssi->clk); if (ret) return ret; /* * When using dual fifo mode, it is safer to ensure an even period * size. If appearing to an odd number while DMA always starts its * task from fifo0, fifo1 would be neglected at the end of each * period. But SSI would still access fifo1 with an invalid data. */ if (ssi->use_dual_fifo) snd_pcm_hw_constraint_step(substream->runtime, 0, SNDRV_PCM_HW_PARAM_PERIOD_SIZE, 2); return 0; } static void fsl_ssi_shutdown(struct snd_pcm_substream *substream, struct snd_soc_dai *dai) { struct snd_soc_pcm_runtime *rtd = substream->private_data; struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(rtd->cpu_dai); clk_disable_unprepare(ssi->clk); } /** * Configure Digital Audio Interface bit clock * * Note: This function can be only called when using SSI as DAI master * * Quick instruction for parameters: * freq: Output BCLK frequency = samplerate * slots * slot_width * (In 2-channel I2S Master mode, slot_width is fixed 32) */ static int fsl_ssi_set_bclk(struct snd_pcm_substream *substream, struct snd_soc_dai *dai, struct snd_pcm_hw_params *hw_params) { bool tx2, tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); struct regmap *regs = ssi->regs; u32 pm = 999, div2, psr, stccr, mask, afreq, factor, i; unsigned long clkrate, baudrate, tmprate; unsigned int channels = params_channels(hw_params); unsigned int slot_width = params_width(hw_params); unsigned int slots = 2; u64 sub, savesub = 100000; unsigned int freq; bool baudclk_is_used; int ret; /* Override slots and slot_width if being specifically set... */ if (ssi->slots) slots = ssi->slots; if (ssi->slot_width) slot_width = ssi->slot_width; /* ...but force 32 bits for stereo audio using I2S Master Mode */ if (channels == 2 && (ssi->i2s_net & SSI_SCR_I2S_MODE_MASK) == SSI_SCR_I2S_MODE_MASTER) slot_width = 32; /* Generate bit clock based on the slot number and slot width */ freq = slots * slot_width * params_rate(hw_params); /* Don't apply it to any non-baudclk circumstance */ if (IS_ERR(ssi->baudclk)) return -EINVAL; /* * Hardware limitation: The bclk rate must be * never greater than 1/5 IPG clock rate */ if (freq * 5 > clk_get_rate(ssi->clk)) { dev_err(dai->dev, "bitclk > ipgclk / 5\n"); return -EINVAL; } baudclk_is_used = ssi->baudclk_streams & ~(BIT(substream->stream)); /* It should be already enough to divide clock by setting pm alone */ psr = 0; div2 = 0; factor = (div2 + 1) * (7 * psr + 1) * 2; for (i = 0; i < 255; i++) { tmprate = freq * factor * (i + 1); if (baudclk_is_used) clkrate = clk_get_rate(ssi->baudclk); else clkrate = clk_round_rate(ssi->baudclk, tmprate); clkrate /= factor; afreq = clkrate / (i + 1); if (freq == afreq) sub = 0; else if (freq / afreq == 1) sub = freq - afreq; else if (afreq / freq == 1) sub = afreq - freq; else continue; /* Calculate the fraction */ sub *= 100000; do_div(sub, freq); if (sub < savesub && !(i == 0 && psr == 0 && div2 == 0)) { baudrate = tmprate; savesub = sub; pm = i; } /* We are lucky */ if (savesub == 0) break; } /* No proper pm found if it is still remaining the initial value */ if (pm == 999) { dev_err(dai->dev, "failed to handle the required sysclk\n"); return -EINVAL; } stccr = SSI_SxCCR_PM(pm + 1) | (div2 ? SSI_SxCCR_DIV2 : 0) | (psr ? SSI_SxCCR_PSR : 0); mask = SSI_SxCCR_PM_MASK | SSI_SxCCR_DIV2 | SSI_SxCCR_PSR; /* STCCR is used for RX in synchronous mode */ tx2 = tx || ssi->synchronous; regmap_update_bits(regs, REG_SSI_SxCCR(tx2), mask, stccr); if (!baudclk_is_used) { ret = clk_set_rate(ssi->baudclk, baudrate); if (ret) { dev_err(dai->dev, "failed to set baudclk rate\n"); return -EINVAL; } } return 0; } /** * Configure SSI based on PCM hardware parameters * * Notes: * 1) SxCCR.WL bits are critical bits that require SSI to be temporarily * disabled on offline_config SoCs. Even for online configurable SoCs * running in synchronous mode (both TX and RX use STCCR), it is not * safe to re-configure them when both two streams start running. * 2) SxCCR.PM, SxCCR.DIV2 and SxCCR.PSR bits will be configured in the * fsl_ssi_set_bclk() if SSI is the DAI clock master. */ static int fsl_ssi_hw_params(struct snd_pcm_substream *substream, struct snd_pcm_hw_params *hw_params, struct snd_soc_dai *dai) { bool tx2, tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); struct regmap *regs = ssi->regs; unsigned int channels = params_channels(hw_params); unsigned int sample_size = params_width(hw_params); u32 wl = SSI_SxCCR_WL(sample_size); int ret; if (fsl_ssi_is_i2s_master(ssi)) { ret = fsl_ssi_set_bclk(substream, dai, hw_params); if (ret) return ret; /* Do not enable the clock if it is already enabled */ if (!(ssi->baudclk_streams & BIT(substream->stream))) { ret = clk_prepare_enable(ssi->baudclk); if (ret) return ret; ssi->baudclk_streams |= BIT(substream->stream); } } /* * SSI is properly configured if it is enabled and running in * the synchronous mode; Note that AC97 mode is an exception * that should set separate configurations for STCCR and SRCCR * despite running in the synchronous mode. */ if (ssi->streams && ssi->synchronous) return 0; if (!fsl_ssi_is_ac97(ssi)) { /* * Keep the ssi->i2s_net intact while having a local variable * to override settings for special use cases. Otherwise, the * ssi->i2s_net will lose the settings for regular use cases. */ u8 i2s_net = ssi->i2s_net; /* Normal + Network mode to send 16-bit data in 32-bit frames */ if (fsl_ssi_is_i2s_cbm_cfs(ssi) && sample_size == 16) i2s_net = SSI_SCR_I2S_MODE_NORMAL | SSI_SCR_NET; /* Use Normal mode to send mono data at 1st slot of 2 slots */ if (channels == 1) i2s_net = SSI_SCR_I2S_MODE_NORMAL; regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_I2S_NET_MASK, i2s_net); } /* In synchronous mode, the SSI uses STCCR for capture */ tx2 = tx || ssi->synchronous; regmap_update_bits(regs, REG_SSI_SxCCR(tx2), SSI_SxCCR_WL_MASK, wl); return 0; } static int fsl_ssi_hw_free(struct snd_pcm_substream *substream, struct snd_soc_dai *dai) { struct snd_soc_pcm_runtime *rtd = substream->private_data; struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(rtd->cpu_dai); if (fsl_ssi_is_i2s_master(ssi) && ssi->baudclk_streams & BIT(substream->stream)) { clk_disable_unprepare(ssi->baudclk); ssi->baudclk_streams &= ~BIT(substream->stream); } return 0; } static int _fsl_ssi_set_dai_fmt(struct fsl_ssi *ssi, unsigned int fmt) { u32 strcr = 0, scr = 0, stcr, srcr, mask; ssi->dai_fmt = fmt; /* Synchronize frame sync clock for TE to avoid data slipping */ scr |= SSI_SCR_SYNC_TX_FS; /* Set to default shifting settings: LSB_ALIGNED */ strcr |= SSI_STCR_TXBIT0; /* Use Network mode as default */ ssi->i2s_net = SSI_SCR_NET; switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { case SND_SOC_DAIFMT_I2S: switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { case SND_SOC_DAIFMT_CBS_CFS: if (IS_ERR(ssi->baudclk)) { dev_err(ssi->dev, "missing baudclk for master mode\n"); return -EINVAL; } /* fall through */ case SND_SOC_DAIFMT_CBM_CFS: ssi->i2s_net |= SSI_SCR_I2S_MODE_MASTER; break; case SND_SOC_DAIFMT_CBM_CFM: ssi->i2s_net |= SSI_SCR_I2S_MODE_SLAVE; break; default: return -EINVAL; } regmap_update_bits(ssi->regs, REG_SSI_STCCR, SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(2)); regmap_update_bits(ssi->regs, REG_SSI_SRCCR, SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(2)); /* Data on rising edge of bclk, frame low, 1clk before data */ strcr |= SSI_STCR_TFSI | SSI_STCR_TSCKP | SSI_STCR_TEFS; break; case SND_SOC_DAIFMT_LEFT_J: /* Data on rising edge of bclk, frame high */ strcr |= SSI_STCR_TSCKP; break; case SND_SOC_DAIFMT_DSP_A: /* Data on rising edge of bclk, frame high, 1clk before data */ strcr |= SSI_STCR_TFSL | SSI_STCR_TSCKP | SSI_STCR_TEFS; break; case SND_SOC_DAIFMT_DSP_B: /* Data on rising edge of bclk, frame high */ strcr |= SSI_STCR_TFSL | SSI_STCR_TSCKP; break; case SND_SOC_DAIFMT_AC97: /* Data on falling edge of bclk, frame high, 1clk before data */ strcr |= SSI_STCR_TEFS; break; default: return -EINVAL; } scr |= ssi->i2s_net; /* DAI clock inversion */ switch (fmt & SND_SOC_DAIFMT_INV_MASK) { case SND_SOC_DAIFMT_NB_NF: /* Nothing to do for both normal cases */ break; case SND_SOC_DAIFMT_IB_NF: /* Invert bit clock */ strcr ^= SSI_STCR_TSCKP; break; case SND_SOC_DAIFMT_NB_IF: /* Invert frame clock */ strcr ^= SSI_STCR_TFSI; break; case SND_SOC_DAIFMT_IB_IF: /* Invert both clocks */ strcr ^= SSI_STCR_TSCKP; strcr ^= SSI_STCR_TFSI; break; default: return -EINVAL; } /* DAI clock master masks */ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { case SND_SOC_DAIFMT_CBS_CFS: /* Output bit and frame sync clocks */ strcr |= SSI_STCR_TFDIR | SSI_STCR_TXDIR; scr |= SSI_SCR_SYS_CLK_EN; break; case SND_SOC_DAIFMT_CBM_CFM: /* Input bit or frame sync clocks */ break; case SND_SOC_DAIFMT_CBM_CFS: /* Input bit clock but output frame sync clock */ strcr |= SSI_STCR_TFDIR; break; default: return -EINVAL; } stcr = strcr; srcr = strcr; /* Set SYN mode and clear RXDIR bit when using SYN or AC97 mode */ if (ssi->synchronous || fsl_ssi_is_ac97(ssi)) { srcr &= ~SSI_SRCR_RXDIR; scr |= SSI_SCR_SYN; } mask = SSI_STCR_TFDIR | SSI_STCR_TXDIR | SSI_STCR_TSCKP | SSI_STCR_TFSL | SSI_STCR_TFSI | SSI_STCR_TEFS | SSI_STCR_TXBIT0; regmap_update_bits(ssi->regs, REG_SSI_STCR, mask, stcr); regmap_update_bits(ssi->regs, REG_SSI_SRCR, mask, srcr); mask = SSI_SCR_SYNC_TX_FS | SSI_SCR_I2S_MODE_MASK | SSI_SCR_SYS_CLK_EN | SSI_SCR_SYN; regmap_update_bits(ssi->regs, REG_SSI_SCR, mask, scr); return 0; } /** * Configure Digital Audio Interface (DAI) Format */ static int fsl_ssi_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt) { struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); /* AC97 configured DAIFMT earlier in the probe() */ if (fsl_ssi_is_ac97(ssi)) return 0; return _fsl_ssi_set_dai_fmt(ssi, fmt); } /** * Set TDM slot number and slot width */ static int fsl_ssi_set_dai_tdm_slot(struct snd_soc_dai *dai, u32 tx_mask, u32 rx_mask, int slots, int slot_width) { struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); struct regmap *regs = ssi->regs; u32 val; /* The word length should be 8, 10, 12, 16, 18, 20, 22 or 24 */ if (slot_width & 1 || slot_width < 8 || slot_width > 24) { dev_err(dai->dev, "invalid slot width: %d\n", slot_width); return -EINVAL; } /* The slot number should be >= 2 if using Network mode or I2S mode */ if (ssi->i2s_net && slots < 2) { dev_err(dai->dev, "slot number should be >= 2 in I2S or NET\n"); return -EINVAL; } regmap_update_bits(regs, REG_SSI_STCCR, SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots)); regmap_update_bits(regs, REG_SSI_SRCCR, SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots)); /* Save the SCR register value */ regmap_read(regs, REG_SSI_SCR, &val); /* Temporarily enable SSI to allow SxMSKs to be configurable */ regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_SSIEN, SSI_SCR_SSIEN); regmap_write(regs, REG_SSI_STMSK, ~tx_mask); regmap_write(regs, REG_SSI_SRMSK, ~rx_mask); /* Restore the value of SSIEN bit */ regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_SSIEN, val); ssi->slot_width = slot_width; ssi->slots = slots; return 0; } /** * Start or stop SSI and corresponding DMA transaction. * * The DMA channel is in external master start and pause mode, which * means the SSI completely controls the flow of data. */ static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd, struct snd_soc_dai *dai) { struct snd_soc_pcm_runtime *rtd = substream->private_data; struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(rtd->cpu_dai); bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; switch (cmd) { case SNDRV_PCM_TRIGGER_START: case SNDRV_PCM_TRIGGER_RESUME: case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: /* * SACCST might be modified via AC Link by a CODEC if it sends * extra bits in their SLOTREQ requests, which'll accidentally * send valid data to slots other than normal playback slots. * * To be safe, configure SACCST right before TX starts. */ if (tx && fsl_ssi_is_ac97(ssi)) fsl_ssi_tx_ac97_saccst_setup(ssi); fsl_ssi_config_enable(ssi, tx); break; case SNDRV_PCM_TRIGGER_STOP: case SNDRV_PCM_TRIGGER_SUSPEND: case SNDRV_PCM_TRIGGER_PAUSE_PUSH: fsl_ssi_config_disable(ssi, tx); break; default: return -EINVAL; } return 0; } static int fsl_ssi_dai_probe(struct snd_soc_dai *dai) { struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); if (ssi->soc->imx && ssi->use_dma) snd_soc_dai_init_dma_data(dai, &ssi->dma_params_tx, &ssi->dma_params_rx); return 0; } static const struct snd_soc_dai_ops fsl_ssi_dai_ops = { .startup = fsl_ssi_startup, .shutdown = fsl_ssi_shutdown, .hw_params = fsl_ssi_hw_params, .hw_free = fsl_ssi_hw_free, .set_fmt = fsl_ssi_set_dai_fmt, .set_tdm_slot = fsl_ssi_set_dai_tdm_slot, .trigger = fsl_ssi_trigger, }; static struct snd_soc_dai_driver fsl_ssi_dai_template = { .probe = fsl_ssi_dai_probe, .playback = { .stream_name = "CPU-Playback", .channels_min = 1, .channels_max = 32, .rates = SNDRV_PCM_RATE_CONTINUOUS, .formats = FSLSSI_I2S_FORMATS, }, .capture = { .stream_name = "CPU-Capture", .channels_min = 1, .channels_max = 32, .rates = SNDRV_PCM_RATE_CONTINUOUS, .formats = FSLSSI_I2S_FORMATS, }, .ops = &fsl_ssi_dai_ops, }; static const struct snd_soc_component_driver fsl_ssi_component = { .name = "fsl-ssi", }; static struct snd_soc_dai_driver fsl_ssi_ac97_dai = { .bus_control = true, .symmetric_channels = 1, .probe = fsl_ssi_dai_probe, .playback = { .stream_name = "AC97 Playback", .channels_min = 2, .channels_max = 2, .rates = SNDRV_PCM_RATE_8000_48000, .formats = SNDRV_PCM_FMTBIT_S16 | SNDRV_PCM_FMTBIT_S20, }, .capture = { .stream_name = "AC97 Capture", .channels_min = 2, .channels_max = 2, .rates = SNDRV_PCM_RATE_48000, /* 16-bit capture is broken (errata ERR003778) */ .formats = SNDRV_PCM_FMTBIT_S20, }, .ops = &fsl_ssi_dai_ops, }; static struct fsl_ssi *fsl_ac97_data; static void fsl_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg, unsigned short val) { struct regmap *regs = fsl_ac97_data->regs; unsigned int lreg; unsigned int lval; int ret; if (reg > 0x7f) return; mutex_lock(&fsl_ac97_data->ac97_reg_lock); ret = clk_prepare_enable(fsl_ac97_data->clk); if (ret) { pr_err("ac97 write clk_prepare_enable failed: %d\n", ret); goto ret_unlock; } lreg = reg << 12; regmap_write(regs, REG_SSI_SACADD, lreg); lval = val << 4; regmap_write(regs, REG_SSI_SACDAT, lval); regmap_update_bits(regs, REG_SSI_SACNT, SSI_SACNT_RDWR_MASK, SSI_SACNT_WR); udelay(100); clk_disable_unprepare(fsl_ac97_data->clk); ret_unlock: mutex_unlock(&fsl_ac97_data->ac97_reg_lock); } static unsigned short fsl_ssi_ac97_read(struct snd_ac97 *ac97, unsigned short reg) { struct regmap *regs = fsl_ac97_data->regs; unsigned short val = 0; u32 reg_val; unsigned int lreg; int ret; mutex_lock(&fsl_ac97_data->ac97_reg_lock); ret = clk_prepare_enable(fsl_ac97_data->clk); if (ret) { pr_err("ac97 read clk_prepare_enable failed: %d\n", ret); goto ret_unlock; } lreg = (reg & 0x7f) << 12; regmap_write(regs, REG_SSI_SACADD, lreg); regmap_update_bits(regs, REG_SSI_SACNT, SSI_SACNT_RDWR_MASK, SSI_SACNT_RD); udelay(100); regmap_read(regs, REG_SSI_SACDAT, ®_val); val = (reg_val >> 4) & 0xffff; clk_disable_unprepare(fsl_ac97_data->clk); ret_unlock: mutex_unlock(&fsl_ac97_data->ac97_reg_lock); return val; } static struct snd_ac97_bus_ops fsl_ssi_ac97_ops = { .read = fsl_ssi_ac97_read, .write = fsl_ssi_ac97_write, }; /** * Initialize SSI registers */ static int fsl_ssi_hw_init(struct fsl_ssi *ssi) { u32 wm = ssi->fifo_watermark; /* Initialize regvals */ fsl_ssi_setup_regvals(ssi); /* Set watermarks */ regmap_write(ssi->regs, REG_SSI_SFCSR, SSI_SFCSR_TFWM0(wm) | SSI_SFCSR_RFWM0(wm) | SSI_SFCSR_TFWM1(wm) | SSI_SFCSR_RFWM1(wm)); /* Enable Dual FIFO mode */ if (ssi->use_dual_fifo) regmap_update_bits(ssi->regs, REG_SSI_SCR, SSI_SCR_TCH_EN, SSI_SCR_TCH_EN); /* AC97 should start earlier to communicate with CODECs */ if (fsl_ssi_is_ac97(ssi)) { _fsl_ssi_set_dai_fmt(ssi, ssi->dai_fmt); fsl_ssi_setup_ac97(ssi); } return 0; } /** * Clear SSI registers */ static void fsl_ssi_hw_clean(struct fsl_ssi *ssi) { /* Disable registers for AC97 */ if (fsl_ssi_is_ac97(ssi)) { /* Disable TE and RE bits first */ regmap_update_bits(ssi->regs, REG_SSI_SCR, SSI_SCR_TE | SSI_SCR_RE, 0); /* Disable AC97 mode */ regmap_write(ssi->regs, REG_SSI_SACNT, 0); /* Unset WAIT bits */ regmap_write(ssi->regs, REG_SSI_SOR, 0); /* Disable SSI -- software reset */ regmap_update_bits(ssi->regs, REG_SSI_SCR, SSI_SCR_SSIEN, 0); } } /** * Make every character in a string lower-case */ static void make_lowercase(char *s) { if (!s) return; for (; *s; s++) *s = tolower(*s); } static int fsl_ssi_imx_probe(struct platform_device *pdev, struct fsl_ssi *ssi, void __iomem *iomem) { struct device *dev = &pdev->dev; int ret; /* Backward compatible for a DT without ipg clock name assigned */ if (ssi->has_ipg_clk_name) ssi->clk = devm_clk_get(dev, "ipg"); else ssi->clk = devm_clk_get(dev, NULL); if (IS_ERR(ssi->clk)) { ret = PTR_ERR(ssi->clk); dev_err(dev, "failed to get clock: %d\n", ret); return ret; } /* Enable the clock since regmap will not handle it in this case */ if (!ssi->has_ipg_clk_name) { ret = clk_prepare_enable(ssi->clk); if (ret) { dev_err(dev, "clk_prepare_enable failed: %d\n", ret); return ret; } } /* Do not error out for slave cases that live without a baud clock */ ssi->baudclk = devm_clk_get(dev, "baud"); if (IS_ERR(ssi->baudclk)) dev_dbg(dev, "failed to get baud clock: %ld\n", PTR_ERR(ssi->baudclk)); ssi->dma_params_tx.maxburst = ssi->dma_maxburst; ssi->dma_params_rx.maxburst = ssi->dma_maxburst; ssi->dma_params_tx.addr = ssi->ssi_phys + REG_SSI_STX0; ssi->dma_params_rx.addr = ssi->ssi_phys + REG_SSI_SRX0; /* Use even numbers to avoid channel swap due to SDMA script design */ if (ssi->use_dual_fifo) { ssi->dma_params_tx.maxburst &= ~0x1; ssi->dma_params_rx.maxburst &= ~0x1; } if (!ssi->use_dma) { /* * Some boards use an incompatible codec. Use imx-fiq-pcm-audio * to get it working, as DMA is not possible in this situation. */ ssi->fiq_params.irq = ssi->irq; ssi->fiq_params.base = iomem; ssi->fiq_params.dma_params_rx = &ssi->dma_params_rx; ssi->fiq_params.dma_params_tx = &ssi->dma_params_tx; ret = imx_pcm_fiq_init(pdev, &ssi->fiq_params); if (ret) goto error_pcm; } else { ret = imx_pcm_dma_init(pdev, IMX_SSI_DMABUF_SIZE); if (ret) goto error_pcm; } return 0; error_pcm: if (!ssi->has_ipg_clk_name) clk_disable_unprepare(ssi->clk); return ret; } static void fsl_ssi_imx_clean(struct platform_device *pdev, struct fsl_ssi *ssi) { if (!ssi->use_dma) imx_pcm_fiq_exit(pdev); if (!ssi->has_ipg_clk_name) clk_disable_unprepare(ssi->clk); } static int fsl_ssi_probe_from_dt(struct fsl_ssi *ssi) { struct device *dev = ssi->dev; struct device_node *np = dev->of_node; const struct of_device_id *of_id; const char *p, *sprop; const __be32 *iprop; u32 dmas[4]; int ret; of_id = of_match_device(fsl_ssi_ids, dev); if (!of_id || !of_id->data) return -EINVAL; ssi->soc = of_id->data; ret = of_property_match_string(np, "clock-names", "ipg"); /* Get error code if not found */ ssi->has_ipg_clk_name = ret >= 0; /* Check if being used in AC97 mode */ sprop = of_get_property(np, "fsl,mode", NULL); if (sprop && !strcmp(sprop, "ac97-slave")) { ssi->dai_fmt = FSLSSI_AC97_DAIFMT; ret = of_property_read_u32(np, "cell-index", &ssi->card_idx); if (ret) { dev_err(dev, "failed to get SSI index property\n"); return -EINVAL; } strcpy(ssi->card_name, "ac97-codec"); } else if (!of_find_property(np, "fsl,ssi-asynchronous", NULL)) { /* * In synchronous mode, STCK and STFS ports are used by RX * as well. So the software should limit the sample rates, * sample bits and channels to be symmetric. * * This is exclusive with FSLSSI_AC97_FORMATS as AC97 runs * in the SSI synchronous mode however it does not have to * limit symmetric sample rates and sample bits. */ ssi->synchronous = true; } /* Select DMA or FIQ */ ssi->use_dma = !of_property_read_bool(np, "fsl,fiq-stream-filter"); /* Fetch FIFO depth; Set to 8 for older DT without this property */ iprop = of_get_property(np, "fsl,fifo-depth", NULL); if (iprop) ssi->fifo_depth = be32_to_cpup(iprop); else ssi->fifo_depth = 8; /* Use dual FIFO mode depending on the support from SDMA script */ ret = of_property_read_u32_array(np, "dmas", dmas, 4); if (ssi->use_dma && !ret && dmas[2] == IMX_DMATYPE_SSI_DUAL) ssi->use_dual_fifo = true; /* * Backward compatible for older bindings by manually triggering the * machine driver's probe(). Use /compatible property, including the * address of CPU DAI driver structure, as the name of machine driver * * If card_name is set by AC97 earlier, bypass here since it uses a * different name to register the device. */ if (!ssi->card_name[0] && of_get_property(np, "codec-handle", NULL)) { struct device_node *root = of_find_node_by_path("/"); sprop = of_get_property(root, "compatible", NULL); of_node_put(root); /* Strip "fsl," in the compatible name if applicable */ p = strrchr(sprop, ','); if (p) sprop = p + 1; snprintf(ssi->card_name, sizeof(ssi->card_name), "snd-soc-%s", sprop); make_lowercase(ssi->card_name); ssi->card_idx = 0; } return 0; } static int fsl_ssi_probe(struct platform_device *pdev) { struct regmap_config regconfig = fsl_ssi_regconfig; struct device *dev = &pdev->dev; struct fsl_ssi *ssi; struct resource *res; void __iomem *iomem; int ret = 0; ssi = devm_kzalloc(dev, sizeof(*ssi), GFP_KERNEL); if (!ssi) return -ENOMEM; ssi->dev = dev; /* Probe from DT */ ret = fsl_ssi_probe_from_dt(ssi); if (ret) return ret; if (fsl_ssi_is_ac97(ssi)) { memcpy(&ssi->cpu_dai_drv, &fsl_ssi_ac97_dai, sizeof(fsl_ssi_ac97_dai)); fsl_ac97_data = ssi; } else { memcpy(&ssi->cpu_dai_drv, &fsl_ssi_dai_template, sizeof(fsl_ssi_dai_template)); } ssi->cpu_dai_drv.name = dev_name(dev); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); iomem = devm_ioremap_resource(dev, res); if (IS_ERR(iomem)) return PTR_ERR(iomem); ssi->ssi_phys = res->start; if (ssi->soc->imx21regs) { /* No SACC{ST,EN,DIS} regs in imx21-class SSI */ regconfig.max_register = REG_SSI_SRMSK; regconfig.num_reg_defaults_raw = REG_SSI_SRMSK / sizeof(uint32_t) + 1; } if (ssi->has_ipg_clk_name) ssi->regs = devm_regmap_init_mmio_clk(dev, "ipg", iomem, ®config); else ssi->regs = devm_regmap_init_mmio(dev, iomem, ®config); if (IS_ERR(ssi->regs)) { dev_err(dev, "failed to init register map\n"); return PTR_ERR(ssi->regs); } ssi->irq = platform_get_irq(pdev, 0); if (ssi->irq < 0) { dev_err(dev, "no irq for node %s\n", pdev->name); return ssi->irq; } /* Set software limitations for synchronous mode except AC97 */ if (ssi->synchronous && !fsl_ssi_is_ac97(ssi)) { ssi->cpu_dai_drv.symmetric_rates = 1; ssi->cpu_dai_drv.symmetric_channels = 1; ssi->cpu_dai_drv.symmetric_samplebits = 1; } /* * Configure TX and RX DMA watermarks -- when to send a DMA request * * Values should be tested to avoid FIFO under/over run. Set maxburst * to fifo_watermark to maxiumize DMA transaction to reduce overhead. */ switch (ssi->fifo_depth) { case 15: /* * Set to 8 as a balanced configuration -- When TX FIFO has 8 * empty slots, send a DMA request to fill these 8 slots. The * remaining 7 slots should be able to allow DMA to finish the * transaction before TX FIFO underruns; Same applies to RX. * * Tested with cases running at 48kHz @ 16 bits x 16 channels */ ssi->fifo_watermark = 8; ssi->dma_maxburst = 8; break; case 8: default: /* Safely use old watermark configurations for older chips */ ssi->fifo_watermark = ssi->fifo_depth - 2; ssi->dma_maxburst = ssi->fifo_depth - 2; break; } dev_set_drvdata(dev, ssi); if (ssi->soc->imx) { ret = fsl_ssi_imx_probe(pdev, ssi, iomem); if (ret) return ret; } if (fsl_ssi_is_ac97(ssi)) { mutex_init(&ssi->ac97_reg_lock); ret = snd_soc_set_ac97_ops_of_reset(&fsl_ssi_ac97_ops, pdev); if (ret) { dev_err(dev, "failed to set AC'97 ops\n"); goto error_ac97_ops; } } ret = devm_snd_soc_register_component(dev, &fsl_ssi_component, &ssi->cpu_dai_drv, 1); if (ret) { dev_err(dev, "failed to register DAI: %d\n", ret); goto error_asoc_register; } if (ssi->use_dma) { ret = devm_request_irq(dev, ssi->irq, fsl_ssi_isr, 0, dev_name(dev), ssi); if (ret < 0) { dev_err(dev, "failed to claim irq %u\n", ssi->irq); goto error_asoc_register; } } ret = fsl_ssi_debugfs_create(&ssi->dbg_stats, dev); if (ret) goto error_asoc_register; /* Initially configures SSI registers */ fsl_ssi_hw_init(ssi); /* Register a platform device for older bindings or AC97 */ if (ssi->card_name[0]) { struct device *parent = dev; /* * Do not set SSI dev as the parent of AC97 CODEC device since * it does not have a DT node. Otherwise ASoC core will assume * CODEC has the same DT node as the SSI, so it may bypass the * dai_probe() of SSI and then cause NULL DMA data pointers. */ if (fsl_ssi_is_ac97(ssi)) parent = NULL; ssi->card_pdev = platform_device_register_data(parent, ssi->card_name, ssi->card_idx, NULL, 0); if (IS_ERR(ssi->card_pdev)) { ret = PTR_ERR(ssi->card_pdev); dev_err(dev, "failed to register %s: %d\n", ssi->card_name, ret); goto error_sound_card; } } return 0; error_sound_card: fsl_ssi_debugfs_remove(&ssi->dbg_stats); error_asoc_register: if (fsl_ssi_is_ac97(ssi)) snd_soc_set_ac97_ops(NULL); error_ac97_ops: if (fsl_ssi_is_ac97(ssi)) mutex_destroy(&ssi->ac97_reg_lock); if (ssi->soc->imx) fsl_ssi_imx_clean(pdev, ssi); return ret; } static int fsl_ssi_remove(struct platform_device *pdev) { struct fsl_ssi *ssi = dev_get_drvdata(&pdev->dev); fsl_ssi_debugfs_remove(&ssi->dbg_stats); if (ssi->card_pdev) platform_device_unregister(ssi->card_pdev); /* Clean up SSI registers */ fsl_ssi_hw_clean(ssi); if (ssi->soc->imx) fsl_ssi_imx_clean(pdev, ssi); if (fsl_ssi_is_ac97(ssi)) { snd_soc_set_ac97_ops(NULL); mutex_destroy(&ssi->ac97_reg_lock); } return 0; } #ifdef CONFIG_PM_SLEEP static int fsl_ssi_suspend(struct device *dev) { struct fsl_ssi *ssi = dev_get_drvdata(dev); struct regmap *regs = ssi->regs; regmap_read(regs, REG_SSI_SFCSR, &ssi->regcache_sfcsr); regmap_read(regs, REG_SSI_SACNT, &ssi->regcache_sacnt); regcache_cache_only(regs, true); regcache_mark_dirty(regs); return 0; } static int fsl_ssi_resume(struct device *dev) { struct fsl_ssi *ssi = dev_get_drvdata(dev); struct regmap *regs = ssi->regs; regcache_cache_only(regs, false); regmap_update_bits(regs, REG_SSI_SFCSR, SSI_SFCSR_RFWM1_MASK | SSI_SFCSR_TFWM1_MASK | SSI_SFCSR_RFWM0_MASK | SSI_SFCSR_TFWM0_MASK, ssi->regcache_sfcsr); regmap_write(regs, REG_SSI_SACNT, ssi->regcache_sacnt); return regcache_sync(regs); } #endif /* CONFIG_PM_SLEEP */ static const struct dev_pm_ops fsl_ssi_pm = { SET_SYSTEM_SLEEP_PM_OPS(fsl_ssi_suspend, fsl_ssi_resume) }; static struct platform_driver fsl_ssi_driver = { .driver = { .name = "fsl-ssi-dai", .of_match_table = fsl_ssi_ids, .pm = &fsl_ssi_pm, }, .probe = fsl_ssi_probe, .remove = fsl_ssi_remove, }; module_platform_driver(fsl_ssi_driver); MODULE_ALIAS("platform:fsl-ssi-dai"); MODULE_AUTHOR("Timur Tabi "); MODULE_DESCRIPTION("Freescale Synchronous Serial Interface (SSI) ASoC Driver"); MODULE_LICENSE("GPL v2");