| Age | Commit message (Collapse) | Author |
|---|
|
Put EXPORT_SYMBOLS directly under the exported function.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Minor style fix, following a general code style in the kernel.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Change occurances of list_for_each into list_for_each_entry where
applicable.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Just for cleaning up, introduce a new function get_sample_rate_v2()
for replacing two identical calls in set_sample_rate_v2().
No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Back-merge for cleaning up usb-audio code the recent commit modified,
and further UAC2 autoclock patches.
|
|
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Merge back for-linus branch for the badness table adjustment for VIA codecs
* for-linus:
ALSA: hda - Fix DAC assignment for independent HP
ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader
ALSA: hda - Fix typo in checking IEC958 emphasis bit
ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
ALSA: snd-usb: mixer: propagate errors up the call chain
ALSA: usb: Parse UAC2 extension unit like for UAC1
ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver
|
|
Creation of individual mixer controls may fail, but that shouldn't cause
the entire mixer creation to fail. Even worse, if the mixer creation
fails, that will error out the entire device probing.
All the functions called by parse_audio_unit() should return -EINVAL if
they find descriptors that are unsupported or believed to be malformed,
so we can safely handle this error code as a non-fatal condition in
snd_usb_mixer_controls().
That fixes a long standing bug which is commonly worked around by
adding quirks which make the driver ignore entire interfaces. Some of
them might now be unnecessary.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Rodolfo Thomazelli <pe.soberbo@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In check_input_term() and parse_audio_feature_unit(), propagate the
error value that has been returned by a failing function instead of
-EINVAL. That helps cleaning up the error pathes in the mixer.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
UAC2_EXTENSION_UNIT_V2 differs from UAC1_EXTENSION_UNIT, but can be handled in
the same way when parsing the unit. Otherwise parse_audio_unit() fails when it
sees an extension unit on a UAC2 device.
UAC2_EXTENSION_UNIT_V2 is outside the range allocated by UAC1.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Back-merged for refactoring beep stuff.
|
|
"Playback Design" products need a 50ms delay after setting the USB
interface.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
UAC2 compliant audio devices may announce the capability to transport
raw audio data on their endpoints. Catch this and handle it as
'special' stream on the ALSA side.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This field may use up to 32 bits, so it should be handled as unsigned
int.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The maxpacksize field is given in some quirks, but it gets ignored (in
favour of wMaxPacketSize from the first endpoint.) This patch favours
the one in the quirk.
Digidesign Mbox and Mbox 2 are the only affected quirks and the devices
are assumed to be working without this patch. So for safety against the
values in the quirk being incorrect, remove them.
The datainterval is also ignored but there are not currently any quirks
which choose to override this.
Cc: Damien Zammit <damien@zamaudio.com>
Cc: Chris J Arges <christopherarges@gmail.com>
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The hardware also has a PCM capture device which is not implemented in
this patch.
It may be possible to generalise this to Saffire 6 USB support and some
of the other Focusrite interfaces, but as I don't have access to these
devices we should wait until capture support is working first.
Capture support is not implemented because the code assumes the endpoint
to have its own interface (instead, it shares the interface with playback)
and some thought will be needed to lift this limitation.
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The NuForce UDH-100 numbers its interfaces incorrectly, which makes the
interface associations come out wrong, which results in the driver
erroring out with the message "Audio class v2 interfaces need an
interface association".
Work around this by searching for the interface association descriptor
also in some other place where it might have ended up.
Reported-and-tested-by: Dave Helstroom <helstroom@google.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix three smatch warnings recently introduced:
sound/usb/caiaq/device.c:166 usb_ep1_command_reply_dispatch() warn:
variable dereferenced before check 'cdev' (see line 163)
sound/usb/caiaq/device.c:517 snd_disconnect() warn: variable
dereferenced before check 'card' (see line 514)
sound/usb/caiaq/input.c:510 snd_usb_caiaq_ep4_reply_dispatch() warn:
variable dereferenced before check 'cdev' (see line 506)
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Get rid of the proprietary functions log() and debug() and use the
generic dev_*() approach. A macro is needed to cast a cdev to a struct
device *.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is needed in order to make the device namespace cleaner, and will
help when moving this driver over to dev_*() logging.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
bootresponse in snd_usb_mbox2_boot_quirk is only 12 (decimal) u8's
long, but i9s passed to snd_usb_ctl_msg as it would be 0x12 (hexa)
long. Fix that by having proper size of the array, i.e. 0x12.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Adds quirks and mixer support for the M-Audio Fast Track C600 USB
audio interface. This device is very similar to the C400 - the C600
simply has some more inputs and outputs, so the existing C400 support
is extended to support this device as well.
Signed-off-by: Matt Gruskin <matthew.gruskin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Merge pending fixes that haven't pulled into 3.8.
|
|
into for-linus
|
|
The quirk for the Roland/Cakewalk A-PRO keyboards accidentally used the
wrong interface number, which prevented the driver from attaching to the
device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.37+ <stable@vger.kernel.org>
|
|
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It looks like MODULE_SUPPORTED_DEVICES() is not implemented yet, but
still, having the entries in the list consistently separated by commas
and with balanced parenthesis won't hurt.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit 23caaf19b11e (ALSA: usb-mixer: Add support for Audio Class v2.0)
forgot to adjust the length check for UAC 2.0 feature unit descriptors.
This would make the code abort on encountering a feature unit without
per-channel controls, and thus prevented the driver to work with any
device having such a unit, such as the RME Babyface or Fireface UCX.
Reported-by: Florian Hanisch <fhanisch@uni-potsdam.de>
Tested-by: Matthew Robbetts <wingfeathera@gmail.com>
Tested-by: Michael Beer <beerml@sigma6audio.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: 2.6.35+ <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Because currently snd_printd() and snd_printdd() macros are expanded
to empty when CONFIG_SND_DEBUG=n, a compile warning like below
appears sometimes, and we had to covert it by ugly ifdefs:
sound/pci/hda/patch_sigmatel.c: In function ‘stac92hd71bxx_fixup_hp’:
sound/pci/hda/patch_sigmatel.c:2434:24: warning: unused variable ‘spec’ [-Wunused-variable]
For "fixing" these issues better, this patch replaces snd_printd() and
snd_printdd() definitions with empty inline functions instead of
macros. This should have the same effect but shut up warnings like
above.
But since we had already put ifdefs, changing to inline functions
would trigger compile errors. So, such ifdefs is removed in this
patch.
In addition, snd_pci_quirk name field is defined only when
CONFIG_SND_DEBUG_VERBOSE is set, and the reference to it in
snd_printdd() argument triggers the build errors, too. For avoiding
these errors, introduce a new macro snd_pci_quirk_name() that is
defined no matter how the debug option is set.
Reported-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a preliminary merge before the upcoming merge of generic parser
branch.
|
|
Add names of the clock sources for the M-Audio Fast Track
C400.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Attain constant real-world latency by skipping 16 data packets.
The number of packets to be skipped was found by trial and error.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Taking another look at the C400 descriptors, I see now that there is
a clock selector (0x80) for this device.
Right now, the clock source points to the internal clock (0x81), which
is also valid. When the external clock source (0x82) is selected in the
mixer, and the rates mismatch (if it's free-running it is fixed to
48KHz), xruns will occur.
Set the clock ID to the clock selector unit (0x81), which then
allows the validation code to function correctly.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A patch in the 3.2 kernel caused regression with hotplugging the
M-Audio Fast track pro, or sound after suspend. I don't have the
device so I haven't done a full analysis, but it seems userspace
(both udev and pulseaudio) got confused when a card was created,
immediately destroyed, and then created again.
However, at least one person in the bug report (martin djfun)
reports that this patch resolves the issue for him. It also leaves
a message in the log:
"snd-usb-audio: probe of 1-1.1:1.1 failed with error -5" which is
a bit misleading. It is better than non-working audio, but maybe
there's a more elegant solution?
BugLink: https://bugs.launchpad.net/bugs/1095315
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit [0d9741c0: ALSA: usb-audio: sync ep init fix for
audioformat mismatch] introduced the correction of parameters to be
set for sync EP. But since the new code assumes that the sync EP is
always paired with the data EP of another direction, it triggers Oops
when a device only with a single direction is used.
This patch adds a proper check of sync EP type and the presence of the
paired substream for avoiding the crash.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixes the following sparse warning:
sound/usb/mixer_quirks.c:1209:23: warning:
symbol 'ebox44_table' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch is based on 3.8-rc1. It fixes two things:
1) A kernel panic caused by incorrect allocation of a u8 variable
"bootresponse".
2) A noisy dmesg (urb status -32) caused by broken pipe to an
invalid midi endpoint.
It is also a little cleaner because there is no need for a new
QUIRK_MIDI type as suggested by kernel developers, since the device
follows exactly the MIDIMAN protocol.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Support the Creative BT-D1 Bluetooth USB audio device. Before this
patch, Linux had trouble finding the correct USB descriptors and bailed
out with these messages:
no or invalid class specific endpoint descriptor
Now it still prints these messages on hotplug:
snd-usb-audio: probe of ...:1.0 failed with error -5
snd-usb-audio: probe of ...:1.2 failed with error -5
snd-usb-audio: probe of ...:1.3 failed with error -5
But the device works correctly, including the HID support.
The patch is diff'ed against 3.8-rc1 but should apply to older kernels
as well.
Signed-off-by: Alexander Schremmer <alex@alexanderweb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Enable delay report on capture path. The delay is reset when an
URB is retired and increment at each call to .pointer based
on frame counter changes. The precision of the delay
information is limited to 1ms as in the playback case.
This reverts commit 3f94fad09538ec988919ec3f371841182df71d04.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains overall only driver-specific fixes. Slightly
large LOC are seen in usb-audio driver for a couple of new device
quirks and cs42l71 ASoC driver for enhanced features. The others are
a few small (regression) fixes HD-audio, and yet other small / trival
ASoC fixes."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Support for Digidesign Mbox 2 USB sound card:
ALSA: HDA: Fix sound resume hang
ALSA: hda - bug fix for invalid connection list of Haswell HDMI codec pins
ALSA: hda - Fix the wrong pincaps set in ALC861VD dallas/hp fixup
ALSA: hda - Set codec->single_adc_amp flag for Realtek codecs
ASoC: atmel-ssc: change disable to disable in dts node
ASoC: Prevent pop_wait overwrite
ALSA: usb-audio: ignore-quirk for HP Wireless Audio
ALSA: hda - Always turn on pins for HDMI/DP
ALSA: hda - Fix pin configuration of HP Pavilion dv7
ASoC: core: Fix splitting of log messages
ASoC: cs42l73: Change VSPIN/VSPOUT to VSPINOUT
ASoC: cs42l73: Add DAPM events for power down.
ASoC: cs42l73: Add DMIC's as DAPM inputs.
ASoC: sigmadsp: Fix endianness conversion issue
ASoC: tpa6130a2: Use devm_* APIs
|
|
This patch is the result of a lot of trial and error, since there are no specs
available for the device.
Full duplex support is provided, i.e. playback and recording in stereo.
The format is hardcoded at 48000Hz @ 24 bit, which is the maximum that the
device supports. Also, MIDI in and MIDI out both work.
Users will notice that the S/PDIF light also flashes when playback or recording
is active. I believe this means that S/PDIF input/output is simultaneously
activated with the analogue i/o during use.
But this particular functionality remains untested.
Note that this particular version of the patch is so far untested on the
physical hardware because I have not compiled a full kernel with the changes.
However, extensive testing has been done by many users of the hardware
who believe other versions of my patch have worked since circa 2009.
[Modified to make a function static by tiwai]
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
As Joe Cooper <swelljoe@gmail.com> reported, "On most HP Envy laptops
the snd-usb-audio module causes the system to become unresponsive and
Gnome Shell 3 to crash.".
See also:
http://mailman.alsa-project.org/pipermail/alsa-devel/2012-December/057729.html
Add a quirk to ignore this device (for now) to solve the instability
issue and allow other USB audio devices to be used.
Reported-by: Joe Cooper <swelljoe@gmail.com>
Tested-by: Isaac Smith <hunternet93@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
|
|
The only required change is to extend the existing Xonar U1
mixer quirks to the U3, which seems to be controlled the same
way.
Signed-off-by: Denis Washington <denisw@online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The patch below prevents the 6fire usb driver going into panic state
when stopping playing. On some systems the urb in handler
(usb6fire_pcm_in_urb_handler) is being called while urbs are being
killed off, this causes the driver to set panic state and can result in
the kernel warning 'URB %p submitted while active'.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit 947d299686aa9cc8aecf749d54e8475c6e498956 , "ALSA: snd-usb:
properly initialize the sync endpoint", while correcting the
initialization of the sync endpoint when opening just the data
endpoint, prevents devices that has a sync endpoint, with a channel
number different than that of the data endpoint, from functioning.
Due to a different channel and period bytes count, attempting to
initialize the sync endpoint will fail at the usb host driver.
For example, when using xhci:
cannot submit urb 0, error -90: internal error
With this patch, if a sync endpoint has multiple audioformats, a
matching audioformat is preferred. An audioformat must be found
with at least one channel and support the requested sample rate
and PCM format, otherwise the stream will not be opened.
If the number of channels differ between the selected audioformat
and the requested format, adjust the period bytes count accordingly.
It is safe to perform the calculation on the basis of the channel
count, since the requested PCM audio format and the rate must be
supported by the selected audioformat.
Cc: Jeffrey Barish <jeff_barish@earthlink.net>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit [88a8516a: ALSA: usbaudio: implement USB autosuspend] added
the support of autopm for USB MIDI output, but it didn't take the MIDI
input into account.
This patch adds the following for fixing the autopm:
- Manage the URB start at the first MIDI input stream open, instead of
the time of instance creation
- Move autopm code to the common substream_open()
- Make snd_usbmidi_input_start/_stop() more robust and add the running
state check
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a similar protection against the disconnection race and the
invalid use of usb instance after disconnection, as well as we've done
for the USB audio PCM.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51201
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
Eldad Zack
Takashi Iwai
Torstein Hegge
Daniel Mack
Mark Hills
Clemens Ladisch
Jiri Slaby
Matt Gruskin
Antonio Ospite
David Henningsson
Sachin Kamat
Damien Zammit
Alexander Schremmer
Pierre-Louis Bossart
Linus Torvalds
Denis Washington
Jurgen Kramer
Bill Pemberton