| Age | Commit message (Collapse) | Author |
|---|
|
Antonio Quartulli says:
====================
pull request [net]: batman-adv 20140721
here you have two fixes that we have been testing for quite some time
(this is why they arrived a bit late in the rc cycle).
Patch 1) ensures that BLA packets get dropped and not forwarded to the
mesh even if they reach batman-adv within QinQ frames. Forwarding them
into the mesh means messing up with the TT database of other nodes which
can generate all kind of unexpected behaviours during route computation.
Patch 2) avoids a couple of race conditions triggered upon fast VLAN
deletion-addition. Such race conditions are pretty dangerous because
they not only create inconsistencies in the TT database of the nodes
in the network, but such scenario is also unrecoverable (unless
nodes are rebooted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a benign buffer overflow in ip_options_compile spotted by
AddressSanitizer[1] :
Its benign because we always can access one extra byte in skb->head
(because header is followed by struct skb_shared_info), and in this case
this byte is not even used.
[28504.910798] ==================================================================
[28504.912046] AddressSanitizer: heap-buffer-overflow in ip_options_compile
[28504.913170] Read of size 1 by thread T15843:
[28504.914026] [<ffffffff81802f91>] ip_options_compile+0x121/0x9c0
[28504.915394] [<ffffffff81804a0d>] ip_options_get_from_user+0xad/0x120
[28504.916843] [<ffffffff8180dedf>] do_ip_setsockopt.isra.15+0x8df/0x1630
[28504.918175] [<ffffffff8180ec60>] ip_setsockopt+0x30/0xa0
[28504.919490] [<ffffffff8181e59b>] tcp_setsockopt+0x5b/0x90
[28504.920835] [<ffffffff8177462f>] sock_common_setsockopt+0x5f/0x70
[28504.922208] [<ffffffff817729c2>] SyS_setsockopt+0xa2/0x140
[28504.923459] [<ffffffff818cfb69>] system_call_fastpath+0x16/0x1b
[28504.924722]
[28504.925106] Allocated by thread T15843:
[28504.925815] [<ffffffff81804995>] ip_options_get_from_user+0x35/0x120
[28504.926884] [<ffffffff8180dedf>] do_ip_setsockopt.isra.15+0x8df/0x1630
[28504.927975] [<ffffffff8180ec60>] ip_setsockopt+0x30/0xa0
[28504.929175] [<ffffffff8181e59b>] tcp_setsockopt+0x5b/0x90
[28504.930400] [<ffffffff8177462f>] sock_common_setsockopt+0x5f/0x70
[28504.931677] [<ffffffff817729c2>] SyS_setsockopt+0xa2/0x140
[28504.932851] [<ffffffff818cfb69>] system_call_fastpath+0x16/0x1b
[28504.934018]
[28504.934377] The buggy address ffff880026382828 is located 0 bytes to the right
[28504.934377] of 40-byte region [ffff880026382800, ffff880026382828)
[28504.937144]
[28504.937474] Memory state around the buggy address:
[28504.938430] ffff880026382300: ........ rrrrrrrr rrrrrrrr rrrrrrrr
[28504.939884] ffff880026382400: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28504.941294] ffff880026382500: .....rrr rrrrrrrr rrrrrrrr rrrrrrrr
[28504.942504] ffff880026382600: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28504.943483] ffff880026382700: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28504.944511] >ffff880026382800: .....rrr rrrrrrrr rrrrrrrr rrrrrrrr
[28504.945573] ^
[28504.946277] ffff880026382900: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28505.094949] ffff880026382a00: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28505.096114] ffff880026382b00: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28505.097116] ffff880026382c00: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28505.098472] ffff880026382d00: ffffffff rrrrrrrr rrrrrrrr rrrrrrrr
[28505.099804] Legend:
[28505.100269] f - 8 freed bytes
[28505.100884] r - 8 redzone bytes
[28505.101649] . - 8 allocated bytes
[28505.102406] x=1..7 - x allocated bytes + (8-x) redzone bytes
[28505.103637] ==================================================================
[1] https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerForKernel
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a VLAN interface (on top of batX) is removed and
re-added within a short timeframe TT does not have enough
time to properly cleanup. This creates an internal TT state
mismatch as the newly created softif_vlan will be
initialized from scratch with a TT client count of zero
(even if TT entries for this VLAN still exist). The
resulting TT messages are bogus due to the counter / tt
client listing mismatch, thus creating inconsistencies on
every node in the network
To fix this issue destroy_vlan() has to not free the VLAN
object immediately but it has to be kept alive until all the
TT entries for this VLAN have been removed. destroy_vlan()
still removes the sysfs folder so that the user has the
feeling that everything went fine.
If the same VLAN is re-added before the old object is free'd,
then the latter is resurrected and re-used.
Implement such behaviour by increasing the reference counter
of a softif_vlan object every time a new local TT entry for
such VLAN is created and remove the object from the list
only when all the TT entries have been destroyed.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Since bridge loop avoidance only supports untagged or simple 802.1q
tagged VLAN claim frames, claim frames with stacked VLAN headers (QinQ)
should be detected and dropped. Transporting the over the mesh may cause
problems on the receivers, or create bogus entries in the local tt
tables.
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
*_result[len] is parsed as *(_result[len]) which is not at all what we
want to touch here.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 84a7c0b1db1c ("dns_resolver: assure that dns_query() result is null-terminated")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When kernel generates a handle for a u32 filter, it tries to start
from the max in the bucket. So when we have a filter with the max (fff)
handle, it will cause kernel always generates the same handle for new
filters. This can be shown by the following command:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 parent ffff: protocol ip pref 770 handle 800::fff u32 match ip protocol 1 0xff
tc filter add dev eth0 parent ffff: protocol ip pref 770 u32 match ip protocol 1 0xff
...
we will get some u32 filters with same handle:
# tc filter show dev eth0 parent ffff:
filter protocol ip pref 770 u32
filter protocol ip pref 770 u32 fh 800: ht divisor 1
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
filter protocol ip pref 770 u32 fh 800::fff order 4095 key ht 800 bkt 0
match 00010000/00ff0000 at 8
handles should be unique. This patch fixes it by looking up a bitmap,
so that can guarantee the handle is as unique as possible. For compatibility,
we still start from 0x800.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/nf_tables fixes
The following patchset contains nf_tables fixes, they are:
1) Fix wrong transaction handling when the table flags are not
modified.
2) Fix missing rcu read_lock section in the netlink dump path, which
is not protected by the nfnl_lock.
3) Set NLM_F_DUMP_INTR in the netlink dump path to indicate
interferences with updates.
4) Fix 64 bits chain counters when they are retrieved from a 32 bits
arch, from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed a bug that was introduced by my GRE-GRO patch
(bf5a755f5e9186406bbf50f4087100af5bd68e40 net-gre-gro: Add GRE
support to the GRO stack) that breaks the forwarding path
because various GSO related fields were not set. The bug will
cause on the egress path either the GSO code to fail, or a
GRE-TSO capable (NETIF_F_GSO_GRE) NICs to choke. The following
fix has been tested for both cases.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Bluetooth pairing fixes from Johan Hedberg.
2) ieee80211_send_auth() doesn't allocate enough tail room for the SKB,
from Max Stepanov.
3) New iwlwifi chip IDs, from Oren Givon.
4) bnx2x driver reads wrong PCI config space MSI register, from Yijing
Wang.
5) IPV6 MLD Query validation isn't strong enough, from Hangbin Liu.
6) Fix double SKB free in openvswitch, from Andy Zhou.
7) Fix sk_dst_set() being racey with UDP sockets, leading to strange
crashes, from Eric Dumazet.
8) Interpret the NAPI budget correctly in the new systemport driver,
from Florian Fainelli.
9) VLAN code frees percpu stats in the wrong place, leading to crashes
in the get stats handler. From Eric Dumazet.
10) TCP sockets doing a repair can crash with a divide by zero, because
we invoke tcp_push() with an MSS value of zero. Just skip that part
of the sendmsg paths in repair mode. From Christoph Paasch.
11) IRQ affinity bug fixes in mlx4 driver from Amir Vadai.
12) Don't ignore path MTU icmp messages with a zero mtu, machines out
there still spit them out, and all of our per-protocol handlers for
PMTU can cope with it just fine. From Edward Allcutt.
13) Some NETDEV_CHANGE notifier invocations were not passing in the
correct kind of cookie as the argument, from Loic Prylli.
14) Fix crashes in long multicast/broadcast reassembly, from Jon Paul
Maloy.
15) ip_tunnel_lookup() doesn't interpret wildcard keys correctly, fix
from Dmitry Popov.
16) Fix skb->sk assigned without taking a reference to 'sk' in
appletalk, from Andrey Utkin.
17) Fix some info leaks in ULP event signalling to userspace in SCTP,
from Daniel Borkmann.
18) Fix deadlocks in HSO driver, from Olivier Sobrie.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
hso: fix deadlock when receiving bursts of data
hso: remove unused workqueue
net: ppp: don't call sk_chk_filter twice
mlx4: mark napi id for gro_skb
bonding: fix ad_select module param check
net: pppoe: use correct channel MTU when using Multilink PPP
neigh: sysctl - simplify address calculation of gc_* variables
net: sctp: fix information leaks in ulpevent layer
MAINTAINERS: update r8169 maintainer
net: bcmgenet: fix RGMII_MODE_EN bit
tipc: clear 'next'-pointer of message fragments before reassembly
r8152: fix r8152_csum_workaround function
be2net: set EQ DB clear-intr bit in be_open()
GRE: enable offloads for GRE
farsync: fix invalid memory accesses in fst_add_one() and fst_init_card()
igb: do a reset on SR-IOV re-init if device is down
igb: Workaround for i210 Errata 25: Slow System Clock
usbnet: smsc95xx: add reset_resume function with reset operation
dp83640: Always decode received status frames
r8169: disable L23
...
|
|
The l2tp [get|set]sockopt() code has fallen back to the UDP functions
for socket option levels != SOL_PPPOL2TP since day one, but that has
never actually worked, since the l2tp socket isn't an inet socket.
As David Miller points out:
"If we wanted this to work, it'd have to look up the tunnel and then
use tunnel->sk, but I wonder how useful that would be"
Since this can never have worked so nobody could possibly have depended
on that functionality, just remove the broken code and return -EINVAL.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: James Chapman <jchapman@katalix.com>
Acked-by: David Miller <davem@davemloft.net>
Cc: Phil Turnbull <phil.turnbull@oracle.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code in neigh_sysctl_register() relies on a specific layout of
struct neigh_table, namely that the 'gc_*' variables are directly
following the 'parms' member in a specific order. The code, though,
expresses this in the most ugly way.
Get rid of the ugly casts and use the 'tbl' pointer to get a handle to
the table. This way we can refer to the 'gc_*' variables directly.
Similarly seen in the grsecurity patch, written by Brad Spengler.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While working on some other SCTP code, I noticed that some
structures shared with user space are leaking uninitialized
stack or heap buffer. In particular, struct sctp_sndrcvinfo
has a 2 bytes hole between .sinfo_flags and .sinfo_ppid that
remains unfilled by us in sctp_ulpevent_read_sndrcvinfo() when
putting this into cmsg. But also struct sctp_remote_error
contains a 2 bytes hole that we don't fill but place into a skb
through skb_copy_expand() via sctp_ulpevent_make_remote_error().
Both structures are defined by the IETF in RFC6458:
* Section 5.3.2. SCTP Header Information Structure:
The sctp_sndrcvinfo structure is defined below:
struct sctp_sndrcvinfo {
uint16_t sinfo_stream;
uint16_t sinfo_ssn;
uint16_t sinfo_flags;
<-- 2 bytes hole -->
uint32_t sinfo_ppid;
uint32_t sinfo_context;
uint32_t sinfo_timetolive;
uint32_t sinfo_tsn;
uint32_t sinfo_cumtsn;
sctp_assoc_t sinfo_assoc_id;
};
* 6.1.3. SCTP_REMOTE_ERROR:
A remote peer may send an Operation Error message to its peer.
This message indicates a variety of error conditions on an
association. The entire ERROR chunk as it appears on the wire
is included in an SCTP_REMOTE_ERROR event. Please refer to the
SCTP specification [RFC4960] and any extensions for a list of
possible error formats. An SCTP error notification has the
following format:
struct sctp_remote_error {
uint16_t sre_type;
uint16_t sre_flags;
uint32_t sre_length;
uint16_t sre_error;
<-- 2 bytes hole -->
sctp_assoc_t sre_assoc_id;
uint8_t sre_data[];
};
Fix this by setting both to 0 before filling them out. We also
have other structures shared between user and kernel space in
SCTP that contains holes (e.g. struct sctp_paddrthlds), but we
copy that buffer over from user space first and thus don't need
to care about it in that cases.
While at it, we can also remove lengthy comments copied from
the draft, instead, we update the comment with the correct RFC
number where one can look it up.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use generic u64_stats_sync infrastructure to get proper 64bit stats,
even on 32bit arches, at no extra cost for 64bit arches.
Without this fix, 32bit arches can have some wrong counters at the time
the carry is propagated into upper word.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
An updater may interfer with the dumping of any of the object lists.
Fix this by using a per-net generation counter and use the
nl_dump_check_consistent() interface so the NLM_F_DUMP_INTR flag is set
to notify userspace that it has to restart the dump since an updater
has interfered.
This patch also replaces the existing consistency checking code in the
rule dumping path since it is broken. Basically, the value that the
dump callback returns is not propagated to userspace via
netlink_dump_start().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The dump operation through netlink is not protected by the nfnl_lock.
Thus, a reader process can be dumping any of the existing object
lists while another process can be updating the list content.
This patch resolves this situation by protecting all the object
lists with RCU in the netlink dump path which is the reader side.
The updater path is already protected via nfnl_lock, so use list
manipulation RCU-safe operations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If the 'next' pointer of the last fragment buffer in a message is not
zeroed before reassembly, we risk ending up with a corrupt message,
since the reassembly function itself isn't doing this.
Currently, when a buffer is retrieved from the deferred queue of the
broadcast link, the next pointer is not cleared, with the result as
described above.
This commit corrects this, and thereby fixes a bug that may occur when
long broadcast messages are transmitted across dual interfaces. The bug
has been present since 40ba3cdf542a469aaa9083fa041656e59b109b90 ("tipc:
message reassembly using fragment chain")
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To get offloads to work with Generic Routing Encapsulation (GRE), the
outer transport header has to be reset after skb_push is done. This
patch has the support for this fix and hence GRE offloading.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netlink_dump() returns a negative errno value on error. Until now,
netlink_recvmsg() directly recorded that negative value in sk->sk_err, but
that's wrong since sk_err takes positive errno values. (This manifests as
userspace receiving a positive return value from the recv() system call,
falsely indicating success.) This bug was introduced in the commit that
started checking the netlink_dump() return value, commit b44d211 (netlink:
handle errors from netlink_dump()).
Multithreaded Netlink dumps are one way to trigger this behavior in
practice, as described in the commit message for the userspace workaround
posted here:
http://openvswitch.org/pipermail/dev/2014-June/042339.html
This commit also fixes the same bug in netlink_poll(), introduced in commit
cd1df525d (netlink: add flow control for memory mapped I/O).
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting just skb->sk without taking its reference and setting a
destructor is invalid. However, in the places where this was done, skb
is used in a way not requiring skb->sk setting. So dropping the setting
of skb->sk.
Thanks to Eric Dumazet <eric.dumazet@gmail.com> for correct solution.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79441
Reported-by: Ed Martin <edman007@edman007.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes 3 similar bugs where incoming packets might be routed into
wrong non-wildcard tunnels:
1) Consider the following setup:
ip address add 1.1.1.1/24 dev eth0
ip address add 1.1.1.2/24 dev eth0
ip tunnel add ipip1 remote 2.2.2.2 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets from 2.2.2.2 were routed into ipip1 even if it has dst =
1.1.1.2. Moreover even if there was wildcard tunnel like
ip tunnel add ipip0 remote 2.2.2.2 local any mode ipip dev eth0
but it was created before explicit one (with local 1.1.1.1), incoming ipip
packets with src = 2.2.2.2 and dst = 1.1.1.2 were still routed into ipip1.
Same issue existed with all tunnels that use ip_tunnel_lookup (gre, vti)
2) ip address add 1.1.1.1/24 dev eth0
ip tunnel add ipip1 remote 2.2.146.85 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets with dst = 1.1.1.1 were routed into ipip1, no matter what
src address is. Any remote ip address which has ip_tunnel_hash = 0 raised this
issue, 2.2.146.85 is just an example, there are more than 4 million of them.
And again, wildcard tunnel like
ip tunnel add ipip0 remote any local 1.1.1.1 mode ipip dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
Gre & vti tunnels had the same issue.
3) ip address add 1.1.1.1/24 dev eth0
ip tunnel add gre1 remote 2.2.146.84 local 1.1.1.1 key 1 mode gre dev eth0
ip link set gre1 up
Any incoming gre packet with key = 1 were routed into gre1, no matter what
src/dst addresses are. Any remote ip address which has ip_tunnel_hash = 0 raised
the issue, 2.2.146.84 is just an example, there are more than 4 million of them.
Wildcard tunnel like
ip tunnel add gre2 remote any local any key 1 mode gre dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
All this stuff happened because while looking for a wildcard tunnel we didn't
check that matched tunnel is a wildcard one. Fixed.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 37e22164a8a3c39bdad45aa463b1e69a1fdf4110 ("tipc: rename and
move message reassembly function") reassembly of long broadcast messages
has been broken. This is because we test for a non-NULL return value
of the *buf parameter as criteria for succesful reassembly. However, this
parameter is left defined even after reception of the first fragment,
when reassebly is still incomplete. This leads to a kernel crash as soon
as a the first fragment of a long broadcast message is received.
We fix this with this commit, by implementing a stricter behavior of the
function and its return values.
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The undo code assumes that, upon entering loss recovery, TCP
1) always retransmit something
2) the retransmission never fails locally (e.g., qdisc drop)
so undo_marker is set in tcp_enter_recovery() and undo_retrans is
incremented only when tcp_retransmit_skb() is successful.
When the assumption is broken because TCP's cwnd is too small to
retransmit or the retransmit fails locally. The next (DUP)ACK
would incorrectly revert the cwnd and the congestion state in
tcp_try_undo_dsack() or tcp_may_undo(). Subsequent (DUP)ACKs
may enter the recovery state. The sender repeatedly enter and
(incorrectly) exit recovery states if the retransmits continue to
fail locally while receiving (DUP)ACKs.
The fix is to initialize undo_retrans to -1 and start counting on
the first retransmission. Always increment undo_retrans even if the
retransmissions fail locally because they couldn't cause DSACKs to
undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The problem was triggered by these steps:
1) create socket, bind and then setsockopt for add mc group.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("192.168.1.2");
setsockopt(sockfd, IPPROTO_IP, IP_ADD_MEMBERSHIP, &mreq, sizeof(mreq));
2) drop the mc group for this socket.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("0.0.0.0");
setsockopt(sockfd, IPPROTO_IP, IP_DROP_MEMBERSHIP, &mreq, sizeof(mreq));
3) and then drop the socket, I found the mc group was still used by the dev:
netstat -g
Interface RefCnt Group
--------------- ------ ---------------------
eth2 1 255.0.0.37
Normally even though the IP_DROP_MEMBERSHIP return error, the mc group still need
to be released for the netdev when drop the socket, but this process was broken when
route default is NULL, the reason is that:
The ip_mc_leave_group() will choose the in_dev by the imr_interface.s_addr, if input addr
is NULL, the default route dev will be chosen, then the ifindex is got from the dev,
then polling the inet->mc_list and return -ENODEV, but if the default route dev is NULL,
the in_dev and ifIndex is both NULL, when polling the inet->mc_list, the mc group will be
released from the mc_list, but the dev didn't dec the refcnt for this mc group, so
when dropping the socket, the mc_list is NULL and the dev still keep this group.
v1->v2: According Hideaki's suggestion, we should align with IPv6 (RFC3493) and BSDs,
so I add the checking for the in_dev before polling the mc_list, make sure when
we remove the mc group, dec the refcnt to the real dev which was using the mc address.
The problem would never happened again.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A bug was introduced in NETDEV_CHANGE notifier sequence causing the
arp table to be sometimes spuriously cleared (including manual arp
entries marked permanent), upon network link carrier changes.
The changed argument for the notifier was applied only to a single
caller of NETDEV_CHANGE, missing among others netdev_state_change().
So upon net_carrier events induced by the network, which are
triggering a call to netdev_state_change(), arp_netdev_event() would
decide whether to clear or not arp cache based on random/junk stack
values (a kind of read buffer overflow).
Fixes: be9efd365328 ("net: pass changed flags along with NETDEV_CHANGE event")
Fixes: 6c8b4e3ff81b ("arp: flush arp cache on IFF_NOARP change")
Signed-off-by: Loic Prylli <loicp@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pshelar/openvswitch
Pravin B Shelar says:
====================
Open vSwitch
A set of fixes for net.
First bug is related flow-table management. Second one is in sample
action. Third is related flow stats and last one add gre-err handler for ovs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In process_backlog the input_pkt_queue is only checked once for new
packets and quota is artificially reduced to reflect precisely the
number of packets on the input_pkt_queue so that the loop exits
appropriately.
This patches changes the behavior to be more straightforward and
less convoluted. Packets are processed until either the quota
is met or there are no more packets to process.
This patch seems to provide a small, but noticeable performance
improvement. The performance improvement is a result of staying
in the process_backlog loop longer which can reduce number of IPI's.
Performance data using super_netperf TCP_RR with 200 flows:
Before fix:
88.06% CPU utilization
125/190/309 90/95/99% latencies
1.46808e+06 tps
1145382 intrs.sec.
With fix:
87.73% CPU utilization
122/183/296 90/95/99% latencies
1.4921e+06 tps
1021674.30 intrs./sec.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some older router implementations still send Fragmentation Needed
errors with the Next-Hop MTU field set to zero. This is explicitly
described as an eventuality that hosts must deal with by the
standard (RFC 1191) since older standards specified that those
bits must be zero.
Linux had a generic (for all of IPv4) implementation of the algorithm
described in the RFC for searching a list of MTU plateaus for a good
value. Commit 46517008e116 ("ipv4: Kill ip_rt_frag_needed().")
removed this as part of the changes to remove the routing cache.
Subsequently any Fragmentation Needed packet with a zero Next-Hop
MTU has been discarded without being passed to the per-protocol
handlers or notifying userspace for raw sockets.
When there is a router which does not implement RFC 1191 on an
MTU limited path then this results in stalled connections since
large packets are discarded and the local protocols are not
notified so they never attempt to lower the pMTU.
One example I have seen is an OpenBSD router terminating IPSec
tunnels. It's worth pointing out that this case is distinct from
the BSD 4.2 bug which incorrectly calculated the Next-Hop MTU
since the commit in question dismissed that as a valid concern.
All of the per-protocols handlers implement the simple approach from
RFC 1191 of immediately falling back to the minimum value. Although
this is sub-optimal it is vastly preferable to connections hanging
indefinitely.
Remove the Next-Hop MTU != 0 check and allow such packets
to follow the normal path.
Fixes: 46517008e116 ("ipv4: Kill ip_rt_frag_needed().")
Signed-off-by: Edward Allcutt <edward.allcutt@openmarket.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When in repair-mode and TCP_RECV_QUEUE is set, we end up calling
tcp_push with mss_now being 0. If data is in the send-queue and
tcp_set_skb_tso_segs gets called, we crash because it will divide by
mss_now:
[ 347.151939] divide error: 0000 [#1] SMP
[ 347.152907] Modules linked in:
[ 347.152907] CPU: 1 PID: 1123 Comm: packetdrill Not tainted 3.16.0-rc2 #4
[ 347.152907] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 347.152907] task: f5b88540 ti: f3c82000 task.ti: f3c82000
[ 347.152907] EIP: 0060:[<c1601359>] EFLAGS: 00210246 CPU: 1
[ 347.152907] EIP is at tcp_set_skb_tso_segs+0x49/0xa0
[ 347.152907] EAX: 00000b67 EBX: f5acd080 ECX: 00000000 EDX: 00000000
[ 347.152907] ESI: f5a28f40 EDI: f3c88f00 EBP: f3c83d10 ESP: f3c83d00
[ 347.152907] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 347.152907] CR0: 80050033 CR2: 083158b0 CR3: 35146000 CR4: 000006b0
[ 347.152907] Stack:
[ 347.152907] c167f9d9 f5acd080 000005b4 00000002 f3c83d20 c16013e6 f3c88f00 f5acd080
[ 347.152907] f3c83da0 c1603b5a f3c83d38 c10a0188 00000000 00000000 f3c83d84 c10acc85
[ 347.152907] c1ad5ec0 00000000 00000000 c1ad679c 010003e0 00000000 00000000 f3c88fc8
[ 347.152907] Call Trace:
[ 347.152907] [<c167f9d9>] ? apic_timer_interrupt+0x2d/0x34
[ 347.152907] [<c16013e6>] tcp_init_tso_segs+0x36/0x50
[ 347.152907] [<c1603b5a>] tcp_write_xmit+0x7a/0xbf0
[ 347.152907] [<c10a0188>] ? up+0x28/0x40
[ 347.152907] [<c10acc85>] ? console_unlock+0x295/0x480
[ 347.152907] [<c10ad24f>] ? vprintk_emit+0x1ef/0x4b0
[ 347.152907] [<c1605716>] __tcp_push_pending_frames+0x36/0xd0
[ 347.152907] [<c15f4860>] tcp_push+0xf0/0x120
[ 347.152907] [<c15f7641>] tcp_sendmsg+0xf1/0xbf0
[ 347.152907] [<c116d920>] ? kmem_cache_free+0xf0/0x120
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c114f0f0>] ? do_wp_page+0x3e0/0x850
[ 347.152907] [<c161c36a>] inet_sendmsg+0x4a/0xb0
[ 347.152907] [<c1150269>] ? handle_mm_fault+0x709/0xfb0
[ 347.152907] [<c15a006b>] sock_aio_write+0xbb/0xd0
[ 347.152907] [<c1180b79>] do_sync_write+0x69/0xa0
[ 347.152907] [<c1181023>] vfs_write+0x123/0x160
[ 347.152907] [<c1181d55>] SyS_write+0x55/0xb0
[ 347.152907] [<c167f0d8>] sysenter_do_call+0x12/0x28
This can easily be reproduced with the following packetdrill-script (the
"magic" with netem, sk_pacing and limit_output_bytes is done to prevent
the kernel from pushing all segments, because hitting the limit without
doing this is not so easy with packetdrill):
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1460>
+0 > S. 0:0(0) ack 1 <mss 1460>
+0.1 < . 1:1(0) ack 1 win 65000
+0 accept(3, ..., ...) = 4
// This forces that not all segments of the snd-queue will be pushed
+0 `tc qdisc add dev tun0 root netem delay 10ms`
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=2`
+0 setsockopt(4, SOL_SOCKET, 47, [2], 4) = 0
+0 write(4,...,10000) = 10000
+0 write(4,...,10000) = 10000
// Set tcp-repair stuff, particularly TCP_RECV_QUEUE
+0 setsockopt(4, SOL_TCP, 19, [1], 4) = 0
+0 setsockopt(4, SOL_TCP, 20, [1], 4) = 0
// This now will make the write push the remaining segments
+0 setsockopt(4, SOL_SOCKET, 47, [20000], 4) = 0
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=130000`
// Now we will crash
+0 write(4,...,1000) = 1000
This happens since ec3423257508 (tcp: fix retransmission in repair
mode). Prior to that, the call to tcp_push was prevented by a check for
tp->repair.
The patch fixes it, by adding the new goto-label out_nopush. When exiting
tcp_sendmsg and a push is not required, which is the case for tp->repair,
we go to this label.
When repairing and calling send() with TCP_RECV_QUEUE, the data is
actually put in the receive-queue. So, no push is required because no
data has been added to the send-queue.
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Fixes: ec3423257508 (tcp: fix retransmission in repair mode)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Madalin-Cristian reported crashs happening after a recent commit
(5a4ae5f6e7d4 "vlan: unnecessary to check if vlan_pcpu_stats is NULL")
-----------------------------------------------------------------------
root@p5040ds:~# vconfig add eth8 1
root@p5040ds:~# vconfig rem eth8.1
Unable to handle kernel paging request for data at address 0x2bc88028
Faulting instruction address: 0xc058e950
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=8 CoreNet Generic
Modules linked in:
CPU: 3 PID: 2167 Comm: vconfig Tainted: G W 3.16.0-rc3-00346-g65e85bf #2
task: e7264d90 ti: e2c2c000 task.ti: e2c2c000
NIP: c058e950 LR: c058ea30 CTR: c058e900
REGS: e2c2db20 TRAP: 0300 Tainted: G W (3.16.0-rc3-00346-g65e85bf)
MSR: 00029002 <CE,EE,ME> CR: 48000428 XER: 20000000
DEAR: 2bc88028 ESR: 00000000
GPR00: c047299c e2c2dbd0 e7264d90 00000000 2bc88000 00000000 ffffffff 00000000
GPR08: 0000000f 00000000 000000ff 00000000 28000422 10121928 10100000 10100000
GPR16: 10100000 00000000 c07c5968 00000000 00000000 00000000 e2c2dc48 e7838000
GPR24: c07c5bac c07c58a8 e77290cc c07b0000 00000000 c05de6c0 e7838000 e2c2dc48
NIP [c058e950] vlan_dev_get_stats64+0x50/0x170
LR [c058ea30] vlan_dev_get_stats64+0x130/0x170
Call Trace:
[e2c2dbd0] [ffffffea] 0xffffffea (unreliable)
[e2c2dc20] [c047299c] dev_get_stats+0x4c/0x140
[e2c2dc40] [c0488ca8] rtnl_fill_ifinfo+0x3d8/0x960
[e2c2dd70] [c0489f4c] rtmsg_ifinfo+0x6c/0x110
[e2c2dd90] [c04731d4] rollback_registered_many+0x344/0x3b0
[e2c2ddd0] [c047332c] rollback_registered+0x2c/0x50
[e2c2ddf0] [c0476058] unregister_netdevice_queue+0x78/0xf0
[e2c2de00] [c058d800] unregister_vlan_dev+0xc0/0x160
[e2c2de20] [c058e360] vlan_ioctl_handler+0x1c0/0x550
[e2c2de90] [c045d11c] sock_ioctl+0x28c/0x2f0
[e2c2deb0] [c010d070] do_vfs_ioctl+0x90/0x7b0
[e2c2df20] [c010d7d0] SyS_ioctl+0x40/0x80
[e2c2df40] [c000f924] ret_from_syscall+0x0/0x3c
Fix this problem by freeing percpu stats from dev->destructor() instead
of ndo_uninit()
Reported-by: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Fixes: 5a4ae5f6e7d4 ("vlan: unnecessary to check if vlan_pcpu_stats is NULL")
Cc: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-06-27
Please pull the following batch of fixes for the 3.16 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Eliad for a time calculation, a fix from Max for
head/tailroom when sending authentication packets, a revert that Felix
requested since the patch in question broke regulatory and a fix from
myself for an issue with a new command that we advertised in the wrong
place."
For the bluetooth bits, Gustavo says:
"A few fixes for 3.16. This pull request contains a NULL dereference fix,
and some security/pairing fixes."
For the iwlwifi bits, Emmanuel says:
"I have here a fix from Eliad for scheduled scan: it fixes a firmware
assertion. Arik reverts a patch I made that didn't take into account
that 3160 doesn't have UAPSD and hence, we can't assume that all
newer firmwares support the feature. Here too, the visible effect
is a firmware assertion. Along with that, we have a few fixes and
additions to the device list."
For the ath10k bits, Kalle says:
"Bartosz fixed an issue where we were not able to create 8 vdevs when
using DFS. Michal removed a false warning which was just confusing
people."
On top of that...
Arend van Spriel fixes a 'divide by zero' regression in brcmfmac.
Amitkumar Karwar corrects a transmit timeout in mwifiex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have two different ways to handle changes to sk->sk_dst
First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()
Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.
These ways are not inter changeable for a given socket type.
ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.
Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5dfb296b ("udp: ipv4: do not use
sk_dst_lock from softirq context")
In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 9cb3a50c5f63e ("ipv4: Invalidate the socket cached route on pmtu events if possible")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to the race condition in userspace, there is chance that two
overlapping megaflows could be installed in datapath. And this
causes userspace unable to delete the less inclusive megaflow flow
even after it timeout, since the flow_del logic will stop at the
first match of masked flow.
This commit fixes the bug by making the kernel flow_del and flow_get
logic check all masks in that case.
Introduced by 03f0d916a (openvswitch: Mega flow implementation).
Signed-off-by: Alex Wang <alexw@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Skip transaction handling for table updates with no changes in
the flags. This fixes a crash when passing the table flag with all
bits unset.
Reported-by: Ana Rey <anarey@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Flow statistics need to take into account the TCP flags from the packet
currently being processed (in 'key'), not the TCP flags matched by the
flow found in the kernel flow table (in 'flow').
This bug made the Open vSwitch userspace fin_timeout action have no effect
in many cases.
This bug is introduced by commit 88d73f6c411ac2f0578 (openvswitch: Use
TCP flags in the flow key for stats.)
Reported-by: Len Gao <leng@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
kernel crash
When use gre vport, openvswitch register a gre_cisco_protocol but
does not supply a err_handler with it. The gre_cisco_err() in
net/ipv4/gre_demux.c expect err_handler be provided with the
gre_cisco_protocol implementation, and call ->err_handler() without
existence check, cause the kernel crash.
This patch provide a err_handler to fix this bug.
This bug introduced by commit aa310701e787087d (openvswitch: Add gre
tunnel support.)
Signed-off-by: Wei Zhang <asuka.com@163.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
When sample action returns with an error, the skb has already been
freed. This patch fix a bug to make sure we don't free it again.
This bug introduced by commit ccb1352e76cff05 (net: Add Open vSwitch
kernel components.)
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time around. The highlights include:
- iscsi-target CHAP authentication fixes to enforce explicit key
values (Tejas Vaykole + rahul.rane)
- fix a long-standing OOPs in target-core when a alua configfs
attribute is accessed after port symlink has been removed.
(Sebastian Herbszt)
- fix a v3.10.y iscsi-target regression causing the login reject
status class/detail to be ignored (Christoph Vu-Brugier)
- fix a v3.10.y iscsi-target regression to avoid rejecting an
existing ITT during Data-Out when data-direction is wrong (Santosh
Kulkarni + Arshad Hussain)
- fix a iscsi-target related shutdown deadlock on UP kernels (Mikulas
Patocka)
- fix a v3.16-rc1 build issue with vhost-scsi + !CONFIG_NET (MST)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: fix iscsit_del_np deadlock on unload
iovec: move memcpy_from/toiovecend to lib/iovec.c
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
iscsi-target: Explicily clear login response PDU in exception path
target: Fix left-over se_lun->lun_sep pointer OOPs
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
|
|
ERROR: "memcpy_fromiovecend" [drivers/vhost/vhost_scsi.ko] undefined!
commit 9f977ef7b671f6169eca78bf40f230fe84b7c7e5
vhost-scsi: Include prot_bytes into expected data transfer length
in target-pending makes drivers/vhost/scsi.c call memcpy_fromiovecend().
This function is not available when CONFIG_NET is not enabled.
socket.h already includes uio.h, so no callers need updating.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Based on RFC3810 6.2, we also need to check the hop limit and router alert
option besides source address.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MIB counters for rcvbuferrors in UDP to help diagnose problems.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix crash in ipvs tot_stats estimator, from Julian Anastasov.
2) Fix OOPS in nf_nat on netns removal, from Florian Westphal.
3) Really really really fix locking issues in slip and slcan tty write
wakeups, from Tyler Hall.
4) Fix checksum offloading in fec driver, from Fugang Duan.
5) Off by one in BPF instruction limit test, from Kees Cook.
6) Need to clear all TSO capability flags when doing software TSO in
tg3 driver, from Prashant Sreedharan.
7) Fix memory leak in vlan_reorder_header() error path, from Li
RongQing.
8) Fix various bugs in xen-netfront and xen-netback multiqueue support,
from David Vrabel and Wei Liu.
9) Fix deadlock in cxgb4 driver, from Li RongQing.
10) Prevent double free of no-cache DST entries, from Eric Dumazet.
11) Bad csum_start handling in skb_segment() leads to crashes when
forwarding, from Tom Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: fix setting csum_start in skb_segment()
ipv4: fix dst race in sk_dst_get()
net: filter: Use kcalloc/kmalloc_array to allocate arrays
trivial: net: filter: Change kerneldoc parameter order
trivial: net: filter: Fix typo in comment
net: allwinner: emac: Add missing free_irq
cxgb4: use dev_port to identify ports
xen-netback: bookkeep number of active queues in our own module
tg3: Change nvram command timeout value to 50ms
cxgb4: Not need to hold the adap_rcu_lock lock when read adap_rcu_list
be2net: fix qnq mode detection on VFs
of: mdio: fixup of_phy_register_fixed_link parsing of new bindings
at86rf230: fix irq setup
net: phy: at803x: fix coccinelle warnings
net/mlx4_core: Fix the error flow when probing with invalid VF configuration
tulip: Poll link status more frequently for Comet chips
net: huawei_cdc_ncm: increase command buffer size
drivers: net: cpsw: fix dual EMAC stall when connected to same switch
xen-netfront: recreate queues correctly when reconnecting
xen-netfront: fix oops when disconnected from backend
...
|
|
Dave Jones reported that a crash is occurring in
csum_partial
tcp_gso_segment
inet_gso_segment
? update_dl_migration
skb_mac_gso_segment
__skb_gso_segment
dev_hard_start_xmit
sch_direct_xmit
__dev_queue_xmit
? dev_hard_start_xmit
dev_queue_xmit
ip_finish_output
? ip_output
ip_output
ip_forward_finish
ip_forward
ip_rcv_finish
ip_rcv
__netif_receive_skb_core
? __netif_receive_skb_core
? trace_hardirqs_on
__netif_receive_skb
netif_receive_skb_internal
napi_gro_complete
? napi_gro_complete
dev_gro_receive
? dev_gro_receive
napi_gro_receive
It looks like a likely culprit is that SKB_GSO_CB()->csum_start is
not set correctly when doing non-scatter gather. We are using
offset as opposed to doffset.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 7e2b10c1e52ca ("net: Support for multiple checksums with gso")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.
In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.
DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.
Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kcalloc/kmalloc_array to make it clear we're allocating arrays. No
integer overflow can actually happen here, since len/flen is guaranteed
to be less than BPF_MAXINSNS (4096). However, this changed makes sure
we're not going to get one if BPF_MAXINSNS were ever increased.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the order of the parameters to sk_unattached_filter_create() in
the kerneldoc to reflect the order they appear in the actual function.
This fix is only cosmetic, in the generated doc they still appear in the
correct order without the fix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
|
|
|
|
Fix nfs4_negotiate_security to create an rpc_clnt used to test each SECINFO
returned pseudoflavor. Check credential creation (and gss_context creation)
which is important for RPC_AUTH_GSS pseudoflavors which can fail for multiple
reasons including mis-configuration.
Don't call nfs4_negotiate in nfs4_submount as it was just called by
nfs4_proc_lookup_mountpoint (nfs4_proc_lookup_common)
Signed-off-by: Andy Adamson <andros@netapp.com>
[Trond: fix corrupt return value from nfs_find_best_sec()]
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
David S. Miller
Eric Dumazet
Antonio Quartulli
Simon Wunderlich
Ben Hutchings
Cong Wang
Jerry Chu
Linus Torvalds
Sasha Levin
Mathias Krause
Daniel Borkmann
Pablo Neira Ayuso
Jon Paul Maloy
Amritha Nambiar
Ben Pfaff
Andrey Utkin
Dmitry Popov
Yuchung Cheng
dingtianhong
Loic Prylli
Tom Herbert
Edward Allcutt
Christoph Paasch
Alex Wang
Wei Zhang
Andy Zhou
Michael S. Tsirkin
John W. Linville
Hangbin Liu
James M Leddy
Tobias Klauser
Andy Adamson