| Age | Commit message (Collapse) | Author |
|---|
|
While reviewing the DPAA2 work, it has become apparent that we need
better documentation about which members of the phylink link state
structure are valid in the mac_config call. Improve this
documentation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A detail for mac_config() had been missed in the documentation for the
method - it is expected that the method will update the MAC to the
settings, rather than completely reprogram the MAC on each call.
Update the documentation for this method for this detail.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide phylink_init_eee() to allow MAC drivers to initialise PHY EEE
from within the ethtool set_eee() method.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper for MAC drivers to use in their validate callback to deal
with 2500BaseX vs 1000BaseX modes, where the hardware supports both
but it is not possible to automatically select between them.
This helper defaults to 1000BaseX, as that is the 802.3 standard, and
will allow users to select 2500BaseX either by forcing the speed if
AN is disabled, or by changing the advertising mask if AN is enabled.
Disabling AN is not recommended as it is only the speed that we're
interested in controlling, not the duplex or pause mode parameters.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink_get_fixed_state() currently consults an optional "link_gpio"
GPIO descriptor, expand this mechanism to allow specifying a custom
callback. This is necessary to support out of band link notifcation
(e.g: from an interrupt within a MMIO register).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to let subsystems like DSA fully utilize PHYLINK, we need to be able
to communicate phy_device::flags from of_phy_{connect,attach} even when using
PHYLINK APIs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert phylink to fwnode, switching phylink_create() from taking a
device_node to taking a fwnode_handle. This will allow other firmware
systems to take advantage of sfp/phylink support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add kernel-doc documentation for phylink kernel APIs, and link it into
the networking kapi documentation under "Network device support".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink_init_eee() serves no purpose, remove it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the handling of SGMII and 802.3z is now the same, combine the
MLO_AN_xxx constants into a single MLO_AN_INBAND, and use the PHY
interface mode to distinguish between Cisco SGMII and 802.3z.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for reading module EEPROMs through phylink.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Russell King - ARM Linux admin
Russell King
Florian Fainelli
Russell King