| Age | Commit message (Collapse) | Author |
|---|
|
commit d98f1cd0a3b70ea91f1dfda3ac36c3b2e1a4d5e2 upstream.
When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880
Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata7.00: BMDMA2 stat 0x50001
ata7.00: failed command: DATA SET MANAGEMENT
ata7.00: cmd 06/01:01:00:00:00/00:00:00:00:00/a0 tag 0 dma 512 out
res 51/04:01:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
ata7.00: status: { DRDY ERR }
ata7.00: error: { ABRT }
ata7.00: device reported invalid CHS sector 0
sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 8:0:0:0: [sdb] tag#0 Sense Key : Illegal Request [current] [descriptor]
sd 8:0:0:0: [sdb] tag#0 Add. Sense: Unaligned write command
sd 8:0:0:0: [sdb] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 21 95 88 00 20 00 00 00 00
blk_update_request: I/O error, dev sdb, sector 2200968
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cecd9ab80f43972c056dc068338f7bcc407b71c upstream.
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c13f99b7e945dad5273a8b7ee230f4d1f22d3354 upstream.
The virtio core uses a static ida named virtio_index_ida for
assigning index numbers to virtio devices during registration.
The ida core may allocate some internal idr cache layers and
an ida bitmap upon any ida allocation, and all these layers are
truely freed only upon the ida destruction. The virtio_index_ida
is not destroyed at present, leading to a memory leak when using
the virtio core as a module and atleast one virtio device is
registered and unregistered.
Fix this by invoking ida_destroy() in the virtio core module
exit.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d94e5a61357a04938ce14d6033b4d33a3c5fd780 upstream.
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Given the following sample LIO subtopology,
% targetcli ls /loopback/
o- loopback ................................. [1 Target]
o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
o- luns ................................... [2 LUNs]
o- lun0 ................ [iblock/ram0 (/dev/ram0)]
o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3
[3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4
the following bug can be observed in Linux 4.3 and 4.4~rc1:
% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
00000200
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 057085e522f8bf94c2e691a5b76880f68060f8ba upstream.
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3df0465db00cf4ed9f90d0bfc3b827d32b9c796 upstream.
Anytime a write operation is performed with Reliable Write flag enabled,
the eMMC device is enforced to bypass the cache and do a write to the
underling NVM device by Jedec specification; this causes a performance
penalty since write operations can't be optimized by the device cache.
In our tests, we replayed a typical mobile daily trace pattern and found
~9% overall time reduction in trace replay by using this patch. Also the
write ops within 4KB~64KB chunk size range get a 40~60% performance
improvement by using the patch (as this range of write chunks are the ones
affected by REQ_META).
This patch has been discussed in the Mobile & Embedded Linux Storage Forum
and it's the results of feedbacks from many people. We also checked with
fsdevl and f2fs mailing list developers that this change in the usage of
REQ_META is not affecting FS behavior and we got positive feedbacks.
Reporting here the feedbacks:
http://comments.gmane.org/gmane.linux.file-systems/97219
http://thread.gmane.org/gmane.linux.file-systems.f2fs/3178/focus=3183
Signed-off-by: Bruce Ford <bford@micron.com>
Signed-off-by: Luca Porzio <lporzio@micron.com>
Fixes: ce39f9d17c14 ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8cf308e1225f5f93575f03cc4dbef24516fa81c9 upstream.
Don't set the SRB_FLAGS_QUEUE_ACTION_ENABLE flag since we are not specifying
tags. Without this, the qlogic driver doesn't work properly with storvsc.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 323c4a02c631d00851d8edc4213c4d184ef83647 upstream.
This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 357ae967ad66e357f78b5cfb5ab6ca07fb4a7758 upstream.
Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39416677b95bf1ab8bbfa229ec7e511c96ad5d0c upstream.
We replace __fls() by __ffs() since we have to find a *minimum* data width that
satisfies both source and destination.
While here, rename dwc_fast_fls() to dwc_fast_ffs() which it really is.
Fixes: 4c2d56c574db (dw_dmac: introduce dwc_fast_fls())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90adf98d9530054b8e665ba5a928de4307231d84 upstream.
Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.
Fixes: b5874f33bbaf ("wm831x_power: Use genirq")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e7697ed79d0c0d5f869c87a6b3ce3d5cd1a07d6 upstream.
On some cards it takes a relatively long time for the change
to take place. Make a timeout non-fatal.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76130
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24dd2f64c5a877392925202321c7c2c46c2b0ddf upstream.
Avoids spew on resume for systems where sysfs may
fail even on init.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=106851
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9eccf24615672896dc13251410c3f2f33a14f95 upstream.
The vt8500 clocksource driver declares itself as capable to handle the
minimum delay of 4 cycles by passing the value into
clockevents_config_and_register(). The vt8500_timer_set_next_event()
requires the passed cycles value to be at least 16. The impact is that
userspace hangs in nanosleep() calls with small delay intervals.
This problem is reproducible in Linux 4.2 starting from:
c6eb3f70d448 ('hrtimer: Get rid of hrtimer softirq')
From Russell King, more detailed explanation:
"It's a speciality of the StrongARM/PXA hardware. It takes a certain
number of OSCR cycles for the value written to hit the compare registers.
So, if a very small delta is written (eg, the compare register is written
with a value of OSCR + 1), the OSCR will have incremented past this value
before it hits the underlying hardware. The result is, that you end up
waiting a very long time for the OSCR to wrap before the event fires.
So, we introduce a check in set_next_event() to detect this and return
-ETIME if the calculated delta is too small, which causes the generic
clockevents code to retry after adding the min_delta specified in
clockevents_config_and_register() to the current time value.
min_delta must be sufficient that we don't re-trip the -ETIME check - if
we do, we will return -ETIME, forward the next event time, try to set it,
return -ETIME again, and basically lock the system up. So, min_delta
must be larger than the check inside set_next_event(). A factor of two
was chosen to ensure that this situation would never occur.
The PXA code worked on PXA systems for years, and I'd suggest no one
changes this mechanism without access to a wide range of PXA systems,
otherwise they're risking breakage."
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad6afbe9578d1fa26680faf78c846bd8c00d1d6e upstream.
The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.
Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.
This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick Schaaf <netdev@bof.de>
Tested-by: Patrick Schaaf <netdev@bof.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67f1aee6f45059fd6b0f5b0ecb2c97ad0451f6b3 upstream.
The cxgb3_*_send() functions return NET_XMIT_ values, which are
positive integers values. So don't treat positive return values
as an error.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
[a pox on developers and maintainers who do not cc: stable for bug fixes like this - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d061c1caa31d4d9792cfe48a2c6b309a0e01ef46 upstream.
Thomas reports:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=05c6 ProdID=6001 Rev=00.00
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=1234567890ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3158a8d416f4e1b79dcc867d67cb50013140772c upstream.
$ lsusb:
Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option
$ usb-devices:
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 2
P: Vendor=1e0e ProdID=9001 Rev= 2.32
S: Manufacturer=SimTech, Incorporated
S: Product=SimTech, Incorporated
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
The last interface (6) is used for Android Composite ADB interface.
Serial port layout:
0: QCDM/DIAG
1: NMEA
2: AT
3: AT/PPP
4: audio
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6627ae19385283b89356a199d7f03c75ba35fb29 upstream.
Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90cfde46586d2286488d8ed636929e936c0c9ab2 upstream.
This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18d03e8c25f173f4107a40d0b8c24defb6ed69f3 upstream.
When a thin pool is being destroyed delayed work items are
cancelled using cancel_delayed_work(), which doesn't guarantee that on
return the delayed item isn't running. This can cause the work item to
requeue itself on an already destroyed workqueue. Fix this by using
cancel_delayed_work_sync() which guarantees that on return the work item
is not running anymore.
Fixes: 905e51b39a555 ("dm thin: commit outstanding data every second")
Fixes: 85ad643b7e7e5 ("dm thin: add timeout to stop out-of-data-space mode holding IO forever")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49e99fc717f624aa75ca755d6e7bc029efd3f0e9 upstream.
When you take a metadata snapshot the btree roots for the mapping and
details tree need to have their reference counts incremented so they
persist for the lifetime of the metadata snap.
The roots being incremented were those currently written in the
superblock, which could possibly be out of date if concurrent IO is
triggering new mappings, breaking of sharing, etc.
Fix this by performing a commit with the metadata lock held while taking
a metadata snapshot.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
transition
commit 172c238612ebf81cabccc86b788c9209af591f61 upstream.
A thin-pool that is in out-of-data-space (OODS) mode may transition back
to write mode -- without the admin adding more space to the thin-pool --
if/when blocks are released (either by deleting thin devices or
discarding provisioned blocks).
But as part of the thin-pool's earlier transition to out-of-data-space
mode the thin-pool may have set the 'error_if_no_space' flag to true if
the no_space_timeout expires without more space having been made
available. That implementation detail, of changing the pool's
error_if_no_space setting, needs to be reset back to the default that
the user specified when the thin-pool's table was loaded.
Otherwise we'll drop the user requested behaviour on the floor when this
out-of-data-space to write mode transition occurs.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Fixes: 2c43fd26e4 ("dm thin: fix missing out-of-data-space to write mode transition if blocks are released")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f98ca454ad373fc1b76be804fa7138ff68c1d27 upstream.
We apparantly get a hotplug irq before we've initialised
modesetting,
[drm] Loading R100 Microcode
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c125f56f>] __mutex_lock_slowpath+0x23/0x91
*pde = 00000000
Oops: 0002 [#1]
Modules linked in: radeon(+) drm_kms_helper ttm drm i2c_algo_bit backlight pcspkr psmouse evdev sr_mod input_leds led_class cdrom sg parport_pc parport floppy intel_agp intel_gtt lpc_ich acpi_cpufreq processor button mfd_core agpgart uhci_hcd ehci_hcd rng_core snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm usbcore usb_common i2c_i801 i2c_core snd_timer snd soundcore thermal_sys
CPU: 0 PID: 15 Comm: kworker/0:1 Not tainted 4.2.0-rc7-00015-gbf67402 #111
Hardware name: MicroLink /D850MV , BIOS MV85010A.86A.0067.P24.0304081124 04/08/2003
Workqueue: events radeon_hotplug_work_func [radeon]
task: f6ca5900 ti: f6d3e000 task.ti: f6d3e000
EIP: 0060:[<c125f56f>] EFLAGS: 00010282 CPU: 0
EIP is at __mutex_lock_slowpath+0x23/0x91
EAX: 00000000 EBX: f5e900fc ECX: 00000000 EDX: fffffffe
ESI: f6ca5900 EDI: f5e90100 EBP: f5e90000 ESP: f6d3ff0c
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 8005003b CR2: 00000000 CR3: 36f61000 CR4: 000006d0
Stack:
f5e90100 00000000 c103c4c1 f6d2a5a0 f5e900fc f6df394c c125f162 f8b0faca
f6d2a5a0 c138ca00 f6df394c f7395600 c1034741 00d40000 00000000 f6d2a5a0
c138ca00 f6d2a5b8 c138ca10 c1034b58 00000001 f6d40000 f6ca5900 f6d0c940
Call Trace:
[<c103c4c1>] ? dequeue_task_fair+0xa4/0xb7
[<c125f162>] ? mutex_lock+0x9/0xa
[<f8b0faca>] ? radeon_hotplug_work_func+0x17/0x57 [radeon]
[<c1034741>] ? process_one_work+0xfc/0x194
[<c1034b58>] ? worker_thread+0x18d/0x218
[<c10349cb>] ? rescuer_thread+0x1d5/0x1d5
[<c103742a>] ? kthread+0x7b/0x80
[<c12601c0>] ? ret_from_kernel_thread+0x20/0x30
[<c10373af>] ? init_completion+0x18/0x18
Code: 42 08 e8 8e a6 dd ff c3 57 56 53 83 ec 0c 8b 35 48 f7 37 c1 8b 10 4a 74 1a 89 c3 8d 78 04 8b 40 08 89 63
Reported-and-Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 627ccd20b4ad3ba836472468208e2ac4dfadbf03 upstream.
Previously, it would only scan the entire disk if it was starting from
the very start of the disk - i.e. if the previous scan got to the end.
This was broken by refill_full_stripes(), which updates last_scanned so
that refill_dirty was never triggering the searched_from_start path.
But if we change refill_dirty() to always scan the entire disk if
necessary, regardless of what last_scanned was, the code gets cleaner
and we fix that bug too.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d16ce540c94c9d366eb36fc91b7154d92d6397b upstream.
Added a safeguard in the shutdown case. At least while not being
attached it is also possible to trigger a kernel bug by writing into
writeback_running. This change adds the same check before trying to
wake up the thread for that case.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ecf0cdb2b437402110ab57546e02abfa68a716b upstream.
In bcache_init() function it forgot to unregister reboot notifier if
bcache fails to unregister a block device. This commit fixes this.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d4d8573a8451acc9f01cbea24b7e55f04a252fe upstream.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fecaee6f20ee122ad75402c53d8278f9bb142ddc upstream.
This bug can be reproduced by the following script:
#!/bin/bash
bcache_sysfs="/sys/fs/bcache"
function clear_cache()
{
if [ ! -e $bcache_sysfs ]; then
echo "no bcache sysfs"
exit
fi
cset_uuid=$(ls -l $bcache_sysfs|head -n 2|tail -n 1|awk '{print $9}')
sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/detach"
sleep 5
sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/attach"
}
for ((i=0;i<10;i++)); do
clear_cache
done
The warning messages look like below:
[ 275.948611] ------------[ cut here ]------------
[ 275.963840] WARNING: at fs/sysfs/dir.c:512 sysfs_add_one+0xb8/0xd0() (Tainted: P W
--------------- )
[ 275.979253] Hardware name: Tecal RH2285
[ 275.994106] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:09.0/0000:08:00.0/host4/target4:2:1/4:2:1:0/block/sdb/sdb1/bcache/cache'
[ 276.024105] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler
bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas
pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan]
[ 276.072643] Pid: 2765, comm: sh Tainted: P W --------------- 2.6.32 #1
[ 276.089315] Call Trace:
[ 276.105801] [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0
[ 276.122650] [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50
[ 276.139361] [<ffffffff81205c08>] ? sysfs_add_one+0xb8/0xd0
[ 276.156012] [<ffffffff8120609b>] ? sysfs_do_create_link+0x12b/0x170
[ 276.172682] [<ffffffff81206113>] ? sysfs_create_link+0x13/0x20
[ 276.189282] [<ffffffffa03bda21>] ? bcache_device_link+0xc1/0x110 [bcache]
[ 276.205993] [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache]
[ 276.222794] [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache]
[ 276.239680] [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110
[ 276.256594] [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170
[ 276.273364] [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0
[ 276.290133] [<ffffffff811890b1>] ? sys_write+0x51/0x90
[ 276.306368] [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b
[ 276.322301] ---[ end trace 9f5d4fcdd0c3edfb ]---
[ 276.338241] ------------[ cut here ]------------
[ 276.354109] WARNING: at /home/wenqing.lz/bcache/bcache/super.c:720
bcache_device_link+0xdf/0x110 [bcache]() (Tainted: P W --------------- )
[ 276.386017] Hardware name: Tecal RH2285
[ 276.401430] Couldn't create device <-> cache set symlinks
[ 276.401759] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler
bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas
pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan]
[ 276.465477] Pid: 2765, comm: sh Tainted: P W --------------- 2.6.32 #1
[ 276.482169] Call Trace:
[ 276.498610] [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0
[ 276.515405] [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50
[ 276.532059] [<ffffffffa03bda3f>] ? bcache_device_link+0xdf/0x110 [bcache]
[ 276.548808] [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache]
[ 276.565569] [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache]
[ 276.582418] [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110
[ 276.599341] [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170
[ 276.616142] [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0
[ 276.632607] [<ffffffff811890b1>] ? sys_write+0x51/0x90
[ 276.648671] [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b
[ 276.664756] ---[ end trace 9f5d4fcdd0c3edfc ]---
We forget to clear BCACHE_DEV_UNLINK_DONE flag in bcache_device_attach()
function when we attach a backing device first time. After detaching this
backing device, this flag will be true and sysfs_remove_link() isn't called in
bcache_device_unlink(). Then when we attach this backing device again,
sysfs_create_link() will return EEXIST error in bcache_device_link().
So the fix is trival and we clear this flag in bcache_device_link().
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5f1e5adf956e3ba82d204c7c141a75da9fa449a upstream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ef9ccbfcb90cf84bdba320a571b18b05c41101b upstream.
Subject : [PATCH v2] bcache: fix a livelock in btree lock
Date : Wed, 25 Feb 2015 20:32:09 +0800 (02/25/2015 04:32:09 AM)
This commit tries to fix a livelock in bcache. This livelock might
happen when we causes a huge number of cache misses simultaneously.
When we get a cache miss, bcache will execute the following path.
->cached_dev_make_request()
->cached_dev_read()
->cached_lookup()
->bch->btree_map_keys()
->btree_root() <------------------------
->bch_btree_map_keys_recurse() |
->cache_lookup_fn() |
->cached_dev_cache_miss() |
->bch_btree_insert_check_key() -|
[If btree->seq is not equal to seq + 1, we should return
EINTR and traverse btree again.]
In bch_btree_insert_check_key() function we first need to check upgrade
flag (op->lock == -1), and when this flag is true we need to release
read btree->lock and try to take write btree->lock. During taking and
releasing this write lock, btree->seq will be monotone increased in
order to prevent other threads modify this in cache miss (see btree.h:74).
But if there are some cache misses caused by some requested, we could
meet a livelock because btree->seq is always changed by others. Thus no
one can make progress.
This commit will try to take write btree->lock if it encounters a race
when we traverse btree. Although it sacrifice the scalability but we
can ensure that only one can modify the btree.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Joshua Schmid <jschmid@suse.com>
Tested-by: Eric Wheeler <bcache@linux.ewheeler.net>
Cc: Joshua Schmid <jschmid@suse.com>
Cc: Zhu Yanhai <zhu.yanhai@gmail.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28fb4cb7fa6f63dc2fbdb5f2564dcbead8e3eee0 upstream.
Due to a missing initialization there was no way to map fbdev memory.
Thus for example using the Xserver with the fbdev driver failed.
This fix adds initialization for fix.smem_start and fix.smem_len
in the fb_info structure, which fixes this problem.
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Egbert Eich <eich@suse.de>
[pulled from SuSE tree by me - airlied]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1d353ad3d5835b16724653b33c05124e1b5acf1 upstream.
"count" is controlled by the user and it can be negative. Let's prevent
that by making it unsigned. You have to have CAP_SYS_RAWIO to call this
function so the bug is not as serious as it could be.
Fixes: 5369c02d951a ('intel_scu_ipc: Utility driver for intel scu ipc')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c82171167adb8e4ac77b91a42cd49fb211a81a0 upstream.
xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.
When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fda3bec12d0979aae3f02ee645913d66fbc8a26e upstream.
This is a 32-bit register. Apparently harmless on real hardware, but
causing justified warnings in simulation.
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd0d0d4de582a6a61c032332c91f4f4cb2bab569 upstream.
Without i8042.nomux=1 the Elantech touch pad is not working at all on
a Fujitsu Lifebook U745. This patch does not seem necessary for all
U745 (maybe because of different BIOS versions?). However, it was
verified that the patch does not break those (see opensuse bug 883192:
https://bugzilla.opensuse.org/show_bug.cgi?id=883192).
Signed-off-by: Aurélien Francillon <aurelien@francillon.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6544a1df11c48c8413071aac3316792e4678fbfb upstream.
When using a protocol v2 or v3 hardware, elantech uses the function
elantech_report_semi_mt_data() to report data. This devices are rather
creepy because if num_finger is 3, (x2,y2) is (0,0). Yes, only one valid
touch is reported.
Anyway, userspace (libinput) is now confused by these (0,0) touches,
and detect them as palm, and rejects them.
Commit 3c0213d17a09 ("Input: elantech - fix semi-mt protocol for v3 HW")
was sufficient enough for xf86-input-synaptics and libinput before it has
palm rejection. Now we need to actually tell libinput that this device is
a semi-mt one and it should not rely on the actual values of the 2 touches.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60603950f836ef4e88daddf61a273b91e671db2d upstream.
Another Lifebook machine that needs the same quirk as other similar
models to make the driver working.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=883192
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97a249e98a72d6b79fb7350a8dd56b147e9d5bdb upstream.
Without this change, the name entity for mcp4725 is missing in
/sys/bus/iio/devices/iio\:device*/name
With this change, name is reported correctly
Signed-off-by: Yong Li <sdliyong@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d590faf9e8f8509a0a0aa79c38e87fcc6b913248 upstream.
The SPI tx and rx buffers are both supposed to be scan_bytes amount of
bytes large and a common allocation is used to allocate both buffers. This
puts the beginning of the tx buffer scan_bytes bytes after the rx buffer.
The initialization of the tx buffer pointer is done adding scan_bytes to
the beginning of the rx buffer, but since the rx buffer is of type __be16
this will actually add two times as much and the tx buffer ends up pointing
after the allocated buffer.
Fix this by using scan_count, which is scan_bytes / 2, instead of
scan_bytes when initializing the tx buffer pointer.
Fixes: aacff892cbd5 ("staging:iio:adis: Preallocate transfer message")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 231bfe53c57e89857753c940192acba933cba56c upstream.
WARN_ON() only takes a condition argument. I have changed these to
WARN() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5dcbe97bedd6ba4b0f574a96cc2e293d26f3d857 upstream.
The ad5629/ad5669 are the I2C variant of the ad5628/ad5668, which has a SPI
interface. They are mostly identical with the exception that the shift
factor is different. Currently the driver does not take care of this
difference which leads to incorrect DAC output values.
Fix this by introducing a custom channel spec for the ad5629/ad5669 with
the correct shift factor.
Fixes: commit 6a17a0768f77 ("iio:dac:ad5064: Add support for the ad5629r and ad5669r")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03fe472ef33b7f31fbd11d300dbb3fdab9c00fd4 upstream.
i2c_master_send() returns the number of bytes transferred on success while
the ad5064 driver expects that the write() callback returns 0 on success.
Fix that by translating any non negative return value of i2c_master_send()
to 0.
Fixes: commit 6a17a0768f77 ("iio:dac:ad5064: Add support for the ad5629r and ad5669r")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01bb70ae0b98d266fa3e860482c7ce22fa482a6e upstream.
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
root@devkit3250:~# cat /sys/bus/iio/devices/iio\:device0/in_voltage0_raw
------------[ cut here ]------------
WARNING: CPU: 0 PID: 724 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in: sc16is7xx snd_soc_uda1380
CPU: 0 PID: 724 Comm: cat Not tainted 4.3.0-rc2+ #198
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_read_raw+0x38/0x80)
[<>] (lpc32xx_read_raw) from [<>] (iio_read_channel_info+0x70/0x94)
[<>] (iio_read_channel_info) from [<>] (dev_attr_show+0x28/0x4c)
[<>] (dev_attr_show) from [<>] (sysfs_kf_seq_show+0x8c/0xf0)
[<>] (sysfs_kf_seq_show) from [<>] (kernfs_seq_show+0x2c/0x30)
[<>] (kernfs_seq_show) from [<>] (seq_read+0x1c8/0x440)
[<>] (seq_read) from [<>] (kernfs_fop_read+0x38/0x170)
[<>] (kernfs_fop_read) from [<>] (do_readv_writev+0x16c/0x238)
[<>] (do_readv_writev) from [<>] (vfs_readv+0x50/0x58)
[<>] (vfs_readv) from [<>] (default_file_splice_read+0x1a4/0x308)
[<>] (default_file_splice_read) from [<>] (do_splice_to+0x78/0x84)
[<>] (do_splice_to) from [<>] (splice_direct_to_actor+0xc8/0x1cc)
[<>] (splice_direct_to_actor) from [<>] (do_splice_direct+0xa0/0xb8)
[<>] (do_splice_direct) from [<>] (do_sendfile+0x1a8/0x30c)
[<>] (do_sendfile) from [<>] (SyS_sendfile64+0x104/0x10c)
[<>] (SyS_sendfile64) from [<>] (ret_fast_syscall+0x0/0x38)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 785171fd6cd7dcd7ada5a733b6a2d44ec566c3a0 upstream.
While the datasheet for the AD7785 lists 0xXB as the product ID the actual
product ID is 0xX3.
Fix the product ID otherwise the driver will reject the device due to non
matching IDs.
Fixes: e786cc26dcc5 ("staging:iio:ad7793: Implement stricter id checking")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90a88d6ef88edcfc4f644dddc7eef4ea41bccf8b upstream.
This softlockup is currently happening:
[ 444.088002] NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [kworker/1:1:29]
[ 444.088002] Modules linked in: lpfc(-) qla2x00tgt(O) qla2xxx_scst(O) scst_vdisk(O) scsi_transport_fc libcrc32c scst(O) dlm configfs nfsd lockd grace nfs_acl auth_rpcgss sunrpc ed
d snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device dm_mod iTCO_wdt snd_hda_codec_realtek snd_hda_codec_generic gpio_ich iTCO_vendor_support ppdev snd_hda_intel snd_hda_codec snd_hda
_core snd_hwdep tg3 snd_pcm snd_timer libphy lpc_ich parport_pc ptp acpi_cpufreq snd pps_core fjes parport i2c_i801 ehci_pci tpm_tis tpm sr_mod cdrom soundcore floppy hwmon sg 8250_
fintek pcspkr i915 drm_kms_helper uhci_hcd ehci_hcd drm fb_sys_fops sysimgblt sysfillrect syscopyarea i2c_algo_bit usbcore button video usb_common fan ata_generic ata_piix libata th
ermal
[ 444.088002] CPU: 1 PID: 29 Comm: kworker/1:1 Tainted: G O 4.4.0-rc5-2.g1e923a3-default #1
[ 444.088002] Hardware name: FUJITSU SIEMENS ESPRIMO E /D2164-A1, BIOS 5.00 R1.10.2164.A1 05/08/2006
[ 444.088002] Workqueue: fc_wq_4 fc_rport_final_delete [scsi_transport_fc]
[ 444.088002] task: f6266ec0 ti: f6268000 task.ti: f6268000
[ 444.088002] EIP: 0060:[<c07e7044>] EFLAGS: 00000286 CPU: 1
[ 444.088002] EIP is at _raw_spin_unlock_irqrestore+0x14/0x20
[ 444.088002] EAX: 00000286 EBX: f20d3800 ECX: 00000002 EDX: 00000286
[ 444.088002] ESI: f50ba800 EDI: f2146848 EBP: f6269ec8 ESP: f6269ec8
[ 444.088002] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 444.088002] CR0: 8005003b CR2: 08f96600 CR3: 363ae000 CR4: 000006d0
[ 444.088002] Stack:
[ 444.088002] f6269eec c066b0f7 00000286 f2146848 f50ba808 f50ba800 f50ba800 f2146a90
[ 444.088002] f2146848 f6269f08 f8f0a4ed f3141000 f2146800 f2146a90 f619fa00 00000040
[ 444.088002] f6269f40 c026cb25 00000001 166c6392 00000061 f6757140 f6136340 00000004
[ 444.088002] Call Trace:
[ 444.088002] [<c066b0f7>] scsi_remove_target+0x167/0x1c0
[ 444.088002] [<f8f0a4ed>] fc_rport_final_delete+0x9d/0x1e0 [scsi_transport_fc]
[ 444.088002] [<c026cb25>] process_one_work+0x155/0x3e0
[ 444.088002] [<c026cde7>] worker_thread+0x37/0x490
[ 444.088002] [<c027214b>] kthread+0x9b/0xb0
[ 444.088002] [<c07e72c1>] ret_from_kernel_thread+0x21/0x40
What appears to be happening is that something has pinned the target
so it can't go into STARGET_DEL via final release and the loop in
scsi_remove_target spins endlessly until that happens.
The fix for this soft lockup is to not keep looping over a device that
we've called remove on but which hasn't gone into DEL state. This
patch will retain a simplistic memory of the last target and not keep
looping over it.
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82c43310508eb19eb41fe7862e89afeb74030b84 upstream.
I have a Marvell 88SE9230 SATA Controller that has some sort of
integrated console SCSI device attached to one of the ports.
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata14.00: ATAPI: MARVELL VIRTUALL, 1.09, max UDMA/66
ata14.00: configured for UDMA/66
scsi 13:0:0:0: Processor Marvell Console 1.01 PQ: 0 ANSI: 5
Sending it VPD INQUIRY command seem to always fail with following error:
ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata14.00: irq_stat 0x40000001
ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 2 dma 16640 in
Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation)
ata14: hard resetting link
This has been minor annoyance (only error printed on dmesg) until commit
09e2b0b14690 ("scsi: rescan VPD attributes") added call to scsi_attach_vpd()
in scsi_rescan_device(). The commit causes the system to splat out
following errors continuously without ever reaching the UI:
ata14.00: configured for UDMA/66
ata14: EH complete
ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata14.00: irq_stat 0x40000001
ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 6 dma 16640 in
Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation)
ata14: hard resetting link
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata14.00: configured for UDMA/66
ata14: EH complete
ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata14.00: irq_stat 0x40000001
ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 7 dma 16640 in
Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation)
Without in-depth understanding of SCSI layer and the Marvell controller,
I suspect this happens because when the link goes down (because of an
error) we schedule scsi_rescan_device() which again fails to read VPD
data... ad infinitum.
Since VPD data cannot be read from the device anyway we prevent the SCSI
layer from even trying by blacklisting the device. This gets away the
error and the system starts up normally.
[mkp: Widened the match to all revisions of this device]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2d06d4fe0f2cc2df9b17fefec96e6e1a1271d91 upstream.
If MODE SELECT returns with sense '05/91/36' (command lock violation)
it should always be retried without counting the number of retries.
During an HBA upgrade or similar circumstances one might see a flood
of MODE SELECT command from various HBAs, which will easily trigger
the sense code and exceed the retry count.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 461c7fa126794157484dca48e88effa4963e3af3 upstream.
Reduced testcase:
#include <fcntl.h>
#include <unistd.h>
#include <sys/mman.h>
#include <numaif.h>
#define SIZE 0x2000
int main()
{
int fd;
void *p;
fd = open("/dev/sg0", O_RDWR);
p = mmap(NULL, SIZE, PROT_EXEC, MAP_PRIVATE | MAP_LOCKED, fd, 0);
mbind(p, SIZE, 0, NULL, 0, MPOL_MF_MOVE);
return 0;
}
We shouldn't try to migrate pages in sg VMA as we don't have a way to
update Sg_scatter_hold::pages accordingly from mm core.
Let's mark the VMA as VM_IO to indicate to mm core that the VMA is not
migratable.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Shiraz Hashim <shashim@codeaurora.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: syzkaller <syzkaller@googlegroups.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13b4389143413a1f18127c07f72c74cad5b563e8 upstream.
Runtime suspend during driver probe and removal can cause problems.
The driver's runtime_suspend or runtime_resume callbacks may invoked
before the driver has finished binding to the device or after the
driver has unbound from the device.
This problem shows up with the sd and sr drivers, and can cause disk
or CD/DVD drives to become unusable as a result. The fix is simple.
The drivers store a pointer to the scsi_disk or scsi_cd structure as
their private device data when probing is finished, so we simply have
to be sure to clear the private data during removal and test it during
runtime suspend/resume.
This fixes <https://bugs.debian.org/801925>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Paul Menzel <paul.menzel@giantmonkey.de>
Reported-by: Erich Schubert <erich@debian.org>
Reported-by: Alexandre Rossi <alexandre.rossi@gmail.com>
Tested-by: Paul Menzel <paul.menzel@giantmonkey.de>
Tested-by: Erich Schubert <erich@debian.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Mikulas Patocka
Mirza Krak
Suman Anna
Jan Engelhardt
Nicholas Bellinger
Luca Porzio
K. Y. Srinivasan
sumit.saxena@avagotech.com
Andy Shevchenko
Valentin Rothberg
Alex Deucher
Roman Volkov
Manish Chopra
Hariprasad S
Bjørn Mork
Andrey Skvortsov
Ken Lin
Gerhard Uttenthaler
Nikolay Borisov
Joe Thornber
Mike Snitzer
Dave Airlie
Kent Overstreet
Stefan Bader
Zheng Liu
Al Viro
Kent Overstreet
Zheng Liu
Egbert Eich
Dan Carpenter
Mathias Nyman
CQ Tang
Aurélien Francillon
Benjamin Tissoires
Takashi Iwai
Yong Li
Lars-Peter Clausen
Michael Hennerich
Vladimir Zapolskiy
James Bottomley
Mika Westerberg
Hannes Reinecke
Kirill A. Shutemov
Alan Stern