| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit e25d1e8532c3d84f075deca1580a7d61e0f43ce6 upstream.
This patch adds the necessary PCI ID for Intel Jasper Lake
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c3f595a8119207cc0f82b3dc6ec5bbf6f3e6b135 upstream.
This patch adds the necessary PCI ID for TGP-H devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
commit 2655971ad4b34e97dd921df16bb0b08db9449df7 upstream.
dwc3_pci_resume_work() calls pm_runtime_get_sync() that increments
the reference counter. In case of failure, decrement the reference
before returning.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
commit 8d99087c2db863c5fa3a4a1f3cb82b3a493705ca upstream.
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit cb11ea56f37a36288cdd0a4799a983ee3aa437dd upstream.
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
|
|
commit 1cf084d161f40baf4aa6976bb2dcef114adbebd6 upstream.
When going in suspend, in Device mode, then resuming back leads
to the following:
unbalanced disables for USB_PWR_EN
WARNING: CPU: 0 PID: 163 at ../drivers/regulator/core.c:2590 _regulator_disable+0x104/0x180
Hardware name: Amlogic Meson G12A U200 Development Board (DT)
[...]
pc : _regulator_disable+0x104/0x180
lr : _regulator_disable+0x104/0x180
[...]
Call trace:
_regulator_disable+0x104/0x180
regulator_disable+0x40/0x78
dwc3_meson_g12a_otg_mode_set+0x84/0xb0
dwc3_meson_g12a_irq_thread+0x58/0xb8
irq_thread_fn+0x28/0x80
irq_thread+0x118/0x1b8
kthread+0xf4/0x120
ret_from_fork+0x10/0x18
This disables the regulator if enabled on suspend, and the reverse on
resume.
Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
|
|
commit 066c09593454e89bc605ffdff1c9810061f9b1e1 upstream.
Intel Merrifield provides a DR support via PMIC which has its own
extcon driver.
Add a property string to link to that driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 00e21763f2c8cab21b7befa52996d1b18bde5c42 upstream.
The check for the HWO flag in dwc3_gadget_ep_reclaim_trb_sg()
causes us to break out of the loop before we call
dwc3_gadget_ep_reclaim_completed_trb(), which is what likely
should be clearing the HWO flag.
This can cause odd behavior where we never reclaim all the trbs
in the sg list, so we never call giveback on a usb req, and that
will causes transfer stalls.
This effectively resovles the adb stalls seen on HiKey960
after userland changes started only using AIO in adbd.
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Josh Gao <jmgao@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org #4.20+
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
commit d94ea5319813658ad5861d161ae16a194c2abf88 upstream.
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d0550cd20e52558ecf6847a0f96ebd5d944c17e4 upstream.
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c9117 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 49e0590e3a60e75b493e5df879e216e5073c7663 upstream.
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590fe ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a114c4ca64bd522aec1790c7e5c60c882f699d8f upstream.
We track END_TRANSFER command completion. Don't clear transfer
started/ended flag prematurely. Otherwise, we'd run into the problem
with restarting transfer before END_TRANSFER command finishes.
Fixes: 6d8a019614f3 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7ba6b09fda5e0cb741ee56f3264665e0edc64822 upstream.
In certain circumstances, the XHCI SuperSpeed instance in park mode
can fail to recover, thus on Amlogic G12A/G12B/SM1 SoCs when there is high
load on the single XHCI SuperSpeed instance, the controller can crash like:
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
usb 2-1.1-port1: cannot reset (err = -22)
Setting the PARKMODE_DISABLE_SS bit in the DWC3_USB3_GUCTL1 mitigates
the issue. The bit is described as :
"When this bit is set to '1' all SS bus instances in park mode are disabled"
Synopsys explains:
The GUCTL1.PARKMODE_DISABLE_SS is only available in
dwc_usb3 controller running in host mode.
This should not be set for other IPs.
This can be disabled by default based on IP, but I recommend to have a
property to enable this feature for devices that need this.
CC: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2dedea035ae82c5af0595637a6eda4655532b21e upstream.
When skipping TRBs, we need to account for wrapping around the ring
buffer and not modifying some invalid TRBs. Without this fix, dwc3 won't
be able to check for available TRBs.
Cc: stable <stable@vger.kernel.org>
Fixes: 7746a8dfb3f9 ("usb: dwc3: gadget: extract dwc3_gadget_ep_skip_trbs()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
commit dad2aff3e827b112f27fa5e6f2bf87a110067c3f upstream.
If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.
At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.
Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
commit b32196e35bd7bbc8038db1aba1fbf022dc469b6a upstream.
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.
Addresses-Coverity: ("Unused value")
Fixes: 1381a5113caf ("usb: dwc3: debug: purge usage of strcat")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210095139.328711-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5ee858975b13a9b40db00f456989a689fdbb296c upstream.
The current code in dwc3_gadget_ep_reclaim_completed_trb() will
check for IOC/LST bit in the event->status and returns if
IOC/LST bit is set. This logic doesn't work if multiple TRBs
are queued per request and the IOC/LST bit is set on the last
TRB of that request.
Consider an example where a queued request has multiple queued
TRBs and IOC/LST bit is set only for the last TRB. In this case,
the core generates XferComplete/XferInProgress events only for
the last TRB (since IOC/LST are set only for the last TRB). As
per the logic in dwc3_gadget_ep_reclaim_completed_trb()
event->status is checked for IOC/LST bit and returns on the
first TRB. This leaves the remaining TRBs left unhandled.
Similarly, if the gadget function enqueues an unaligned request
with sglist already in it, it should fail the same way, since we
will append another TRB to something that already uses more than
one TRB.
To aviod this, this patch changes the code to check for IOC/LST
bits in TRB->ctrl instead.
At a practical level, this patch resolves USB transfer stalls seen
with adb on dwc3 based HiKey960 after functionfs gadget added
scatter-gather support around v4.20.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
[jstultz: forward ported to mainline, reworded commit log, reworked
to only check trb->ctrl as suggested by Felipe]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5eb5afb07853d6e90d3a2b230c825e028e948f79 upstream.
We should not be reaching into property entries and initialize them by
hand, but rather use proper initializer macros. This way we can alter
internal representation of property entries with no visible changes to
their users.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
On branch xlnx-soc, a curly brace been removed by a merge mistake
that caused a build error, add it back to fix it.
Signed-off-by: Zhang Xiao <xiao.zhang@windriver.com>
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
commit da10bcdd6f70dc9977f2cf18f4783cf78520623a upstream.
If the END_TRANSFER command hasn't completed yet, then don't send the
START_TRANSFER command. The controller may not be able to start if
that's the case. Some controller revisions depend on this. See
commit 76a638f8ac0d ("usb: dwc3: gadget: wait for End Transfer to
complete"). Let's only send START_TRANSFER command after the
END_TRANSFER command had completed.
Fixes: 3aec99154db3 ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c58d8bfc77a2c7f6ff6339b58c9fca7ae6f57e70 upstream.
While the END_TRANSFER command is sent but not completed, any request
dequeue during this time will cause the driver to issue the END_TRANSFER
command. The driver needs to submit the command only once to stop the
controller from processing further. The controller may take more time to
process the same command multiple times unnecessarily. Let's add a flag
DWC3_EP_END_TRANSFER_PENDING to check for this condition.
Fixes: 3aec99154db3 ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
|
|
commit 09ed259fac621634d51cd986aa8d65f035662658 upstream.
VBUS should be turned off when leaving the host mode.
Set GCTL_PRTCAP to device mode in teardown to de-assert DRVVBUS pin to
turn off VBUS power.
Fixes: 5f94adfeed97 ("usb: dwc3: core: refactor mode initialization to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f5ae8869095552e3396ee3e404f9586cc6a828f0 upstream.
There is one more Comet Lake PCH variant, CML-V, that has
its own PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200117093033.48616-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
|
|
commit ea0d762775e20aaff7909a3f0866ff1688b1c618 upstream.
We can only check for IN direction if the request had completed. For OUT
direction, it's perfectly fine that the host can send less than the
setup length. Let's return true fall all cases of OUT direction.
Fixes: e0c42ce590fe ("usb: dwc3: gadget: simplify IOC handling")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/ac5a3593a94fdaa3d92e6352356b5f7a01ccdc7c.1576291140.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
commit 2d7b78f59e020b07fc6338eefe286f54ee2d6773 upstream.
Clear ep0's DWC3_EP_TRANSFER_STARTED flag if the END_TRANSFER command is
completed. Otherwise, we can't start control transfer again after
END_TRANSFER.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d3abda5a98a18e524e17fd4085c9f4bd53e9ef53 upstream.
Normally the END_TRANSFER command completion handler will clear the
DWC3_EP_TRANSFER_STARTED flag. However, if the command was sent without
interrupt on completion, then the flag will not be cleared. Make sure to
clear the flag in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8c7d4b7b3d43c54c0b8c1e4adb917a151c754196 upstream.
This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.
Fixes: f38e35dd84e2 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3c3caae4cd6e122472efcf64759ff6392fb6bce2 upstream.
The original ID that was added for Comet Lake PCH was
actually for the -LP (low power) variant even though the
constant for it said CMLH. Changing that while at it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212093713.60614-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
|
|
commit d8eca64eec7103ab1fbabc0a187dbf6acfb2af93 upstream.
When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.
Fixes: fec9095bdef4 "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a7d9874c6f3fbc8d25cd9ceba35b6822612c4ebf upstream.
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a51bab592fbbef10f0e42a8aed86adfbf6a68fa7 upstream.
After many randconfig builds, one configuration caused a link
error with dwc3-meson-g12a lacking the regmap-mmio code:
drivers/usb/dwc3/dwc3-meson-g12a.o: In function `dwc3_meson_g12a_probe':
dwc3-meson-g12a.c:(.text+0x9f): undefined reference to `__devm_regmap_init_mmio_clk'
Add the select statement that we have for all other users
of that dependency.
Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
|
|
commit 9bbfceea12a8f145097a27d7c7267af25893c060 upstream.
In dwc3_pci_probe a call to platform_device_alloc allocates a device
which is correctly put in case of error except one case: when the call to
platform_device_add_properties fails it directly returns instead of
going to error handling. This commit replaces return with the goto.
Fixes: 1a7b12f69a94 ("usb: dwc3: pci: Supply device properties via driver data")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
[ Upstream commit dc1b5d9aed1794b5a1c6b0da46e372cc09974cbc ]
The required clocks needs to be enabled before the first register
access. After commit fe8abf332b8f ("usb: dwc3: support clocks and resets
for DWC3 core"), this happens when the dwc3_core_is_valid function is
called, but the mentioned commit adds that call in the wrong place,
before the clocks are enabled. So, move that call after the
clk_bulk_enable() to ensure the clocks are enabled and the reset
deasserted.
I detected this while, as experiment, I tried to move the clocks and resets
from the glue layer to the DWC3 core on a Samsung Chromebook Plus.
That was not detected before because, in most cases, the glue layer
initializes SoC-specific things and then populates the child "snps,dwc3"
with those clocks already enabled.
Fixes: b873e2d0ea1ef ("usb: dwc3: Do core validation early on probe")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
If there are no entry in request list (i.e, both pending_list and
started_list are empty) then do not issue END_TRANSFER instead set
the PENDING flag, so that the END_TRANSFER is issued when an new
entry is added into request list. This patch updates the same.
If the isocronous transfers are started before XFERNOTREADY event,
there are chances of getting BUS_EXPIRY. So, this patch updates the
code to not issue __dwc3_gadget_start_isoc() before XFERNOTREADY
event and wait for dwc3_gadget_endpoint_transfer_not_ready() to
start the isocronous transfers.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[Quanyang: original patch taken from
https://github.com/Xilinx/linux-xlnx.git xlnx_rebase_v4.19]
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
|
Bruce Ashfield
Heikki Krogerus
Aditya Pakki
Thinh Nguyen
Neil Armstrong
Andy Shevchenko
John Stultz
Pratham Pratap
Colin Ian King
Anurag Kumar Vulisha
Dmitry Torokhov
Zhang Xiao
Bin Liu
Tejas Joglekar
Felipe Balbi
Yinbo Zhu
Arnd Bergmann
Navid Emamdoost
Enric Balletbo i Serra