Age | Commit message (Collapse) | Author |
|
commit 03cd45d2e219301880cabc357e3cf478a500080f upstream.
The driver does not populate .reg_read callback for the non-active NVMem
because the file is supposed to be write-only. However, it turns out
NVMem subsystem does not yet support this and expects that the .reg_read
callback is provided. If user reads the binary attribute it triggers
NULL pointer dereference like this one:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
Call Trace:
bin_attr_nvmem_read+0x64/0x80
kernfs_fop_read+0xa7/0x180
vfs_read+0xbd/0x170
ksys_read+0x5a/0xd0
do_syscall_64+0x43/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this in the driver by providing .reg_read callback that always
returns an error.
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Fixes: e6b245ccd524 ("thunderbolt: Add support for host and device NVM firmware upgrade")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200213095604.1074-1-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7a7ebfa85f4fac349f3ab219538c44efe18b0cf6 upstream.
On zang's Dell XPS 13 9370 after Thunderbolt NVM firmware upgrade the
Thunderbolt controller did not come back as expected. Only after the
system was rebooted it became available again. It is not entirely clear
what happened but I suspect the new NVM firmware image authentication
failed for some reason. Regardless of this the router needs to be power
cycled if NVM authentication fails in order to get it fully functional
again.
This modifies the driver to issue a power cycle in case the NVM
authentication fails immediately when dma_port_flash_update_auth()
returns. We also need to call tb_switch_set_uuid() earlier to be able to
fetch possible NVM authentication failure when DMA port is added.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205457
Reported-by: zang <dump@tzib.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6f6709734274aef75058356e029d5e8f86d0d53b upstream.
When lockdep is enabled, plugging Thunderbolt dock on Dominik's laptop
triggers following splat:
======================================================
WARNING: possible circular locking dependency detected
5.3.0-rc6+ #1 Tainted: G T
------------------------------------------------------
pool-/usr/lib/b/1258 is trying to acquire lock:
000000005ab0ad43 (pci_rescan_remove_lock){+.+.}, at: authorized_store+0xe8/0x210
but task is already holding lock:
00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&tb->lock){+.+.}:
__mutex_lock+0xac/0x9a0
tb_domain_add+0x2d/0x130
nhi_probe+0x1dd/0x330
pci_device_probe+0xd2/0x150
really_probe+0xee/0x280
driver_probe_device+0x50/0xc0
bus_for_each_drv+0x84/0xd0
__device_attach+0xe4/0x150
pci_bus_add_device+0x4e/0x70
pci_bus_add_devices+0x2e/0x66
pci_bus_add_devices+0x59/0x66
pci_bus_add_devices+0x59/0x66
enable_slot+0x344/0x450
acpiphp_check_bridge.part.0+0x119/0x150
acpiphp_hotplug_notify+0xaa/0x140
acpi_device_hotplug+0xa2/0x3f0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x234/0x580
worker_thread+0x50/0x3b0
kthread+0x10a/0x140
ret_from_fork+0x3a/0x50
-> #0 (pci_rescan_remove_lock){+.+.}:
__lock_acquire+0xe54/0x1ac0
lock_acquire+0xb8/0x1b0
__mutex_lock+0xac/0x9a0
authorized_store+0xe8/0x210
kernfs_fop_write+0x125/0x1b0
vfs_write+0xc2/0x1d0
ksys_write+0x6c/0xf0
do_syscall_64+0x50/0x180
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&tb->lock);
lock(pci_rescan_remove_lock);
lock(&tb->lock);
lock(pci_rescan_remove_lock);
*** DEADLOCK ***
5 locks held by pool-/usr/lib/b/1258:
#0: 000000003df1a1ad (&f->f_pos_lock){+.+.}, at: __fdget_pos+0x4d/0x60
#1: 0000000095a40b02 (sb_writers#6){.+.+}, at: vfs_write+0x185/0x1d0
#2: 0000000017a7d714 (&of->mutex){+.+.}, at: kernfs_fop_write+0xf2/0x1b0
#3: 000000004f262981 (kn->count#208){.+.+}, at: kernfs_fop_write+0xfa/0x1b0
#4: 00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210
stack backtrace:
CPU: 0 PID: 1258 Comm: pool-/usr/lib/b Tainted: G T 5.3.0-rc6+ #1
On an system using ACPI hotplug the host router gets hotplugged first and then
the firmware starts sending notifications about connected devices so the above
scenario should not happen in reality. However, after taking a second
look at commit a03e828915c0 ("thunderbolt: Serialize PCIe tunnel
creation with PCI rescan") that introduced the locking, I don't think it
is actually correct. It may have cured the symptom but probably the real
root cause was somewhere closer to PCI stack and possibly is already
fixed with recent kernels. I also tried to reproduce the original issue
with the commit reverted but could not.
So to keep lockdep happy and the code bit less complex drop calls to
pci_lock_rescan_remove()/pci_unlock_rescan_remove() in
tb_switch_set_authorized() effectively reverting a03e828915c0.
Link: https://lkml.org/lkml/2019/8/30/513
Fixes: a03e828915c0 ("thunderbolt: Serialize PCIe tunnel creation with PCI rescan")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit fd5c46b754d4799afda8dcdd6851e0390aa4961a upstream.
When we discover existing DP tunnels the code checks whether DP IN
adapter port is enabled by calling tb_dp_port_is_enabled() before it
continues the discovery process. On Light Ridge (gen 1) controller
reading only the first dword of the DP IN config space causes subsequent
access to the same DP IN port path config space to fail or return
invalid data as can be seen in the below splat:
thunderbolt 0000:07:00.0: CFG_ERROR(0:d): Invalid config space or offset
Call Trace:
tb_cfg_read+0xb9/0xd0
__tb_path_deactivate_hop+0x98/0x210
tb_path_activate+0x228/0x7d0
tb_tunnel_restart+0x95/0x200
tb_handle_hotplug+0x30e/0x630
process_one_work+0x1b4/0x340
worker_thread+0x44/0x3d0
kthread+0xeb/0x120
? process_one_work+0x340/0x340
? kthread_park+0xa0/0xa0
ret_from_fork+0x1f/0x30
If both DP In adapter config dwords are read in one go the issue does
not reproduce. This is likely firmware bug but we can work it around by
always reading the two dwords in one go. There should be no harm for
other controllers either so can do it unconditionally.
Link: https://lkml.org/lkml/2019/8/28/160
Reported-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 943795219d3cb9f8ce6ce51cad3ffe1f61e95c6b upstream.
The register access should be using 32-bit reads/writes according to the
datasheet. With the previous generation hardware 16-bit writes have been
working but starting with ICL this is not the case anymore so fix
producer/consumer register update to use correct width register address.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ce19f91eae43e39d5a1da55344756ab5a3c7e8d1 upstream.
PCIe tunnel path indices got mixed up when we added support for tunnels
between switches that are not adjacent. This did not affect the
functionality as it is just an index but fix it now nevertheless to make
the code easier to understand.
Reported-by: Rajmohan Mani <rajmohan.mani@intel.com>
Fixes: 8c7acaaf020f ("thunderbolt: Extend tunnel creation to more than 2 adjacent switches")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
When starting ICM firmware on Apple systems we need to perform CIO reset
as part of the flow. However, it turns out that the reset register has
changed to another location in Titan Ridge.
Fix this by introducing ->cio_reset() callback with corresponding
implementations for Alpine and Titan Ridge.
Fixes: c4630d6ae6e3 ("thunderbolt: Start firmware on Titan Ridge Apple systems")
Reported-by: Peter Bowen <pzb@amazon.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When a device is authorized from userspace by writing to authorized
attribute we first take the domain lock and then runtime resume the
device in question. There are two issues with this.
First is that the device connected notifications are blocked during this
time which means we get them only after the authorization operation is
complete. Because of this the authorization needed flag from the
firmware notification is not reflecting the real authorization status
anymore. So what happens is that the "authorized" keeps returning 0 even
if the device was already authorized properly.
Second issue is that each time the controller is runtime resumed the
connection_id field of device connected notification may be different
than in the previous resume. We need to use the latest connection_id
otherwise the firmware rejects the authorization command.
Fix these by moving runtime resume operations to happen before the
domain lock is taken, and waiting for the updated device connected
notification from the firmware before we allow runtime resume of a
device to complete.
While there add missing locking to tb_switch_nvm_read().
Fixes: 09f11b6c99fe ("thunderbolt: Take domain lock in switch sysfs attribute callbacks")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc update part 2 from Greg KH:
"Here is the "real" big set of char/misc driver patches for 5.2-rc1
Loads of different driver subsystem stuff in here, all over the places:
- thunderbolt driver updates
- habanalabs driver updates
- nvmem driver updates
- extcon driver updates
- intel_th driver updates
- mei driver updates
- coresight driver updates
- soundwire driver cleanups and updates
- fastrpc driver updates
- other minor driver updates
- chardev minor fixups
Feels like this tree is getting to be a dumping ground of "small
driver subsystems" these days. Which is fine with me, if it makes
things easier for those subsystem maintainers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.2-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
intel_th: msu: Add current window tracking
intel_th: msu: Add a sysfs attribute to trigger window switch
intel_th: msu: Correct the block wrap detection
intel_th: Add switch triggering support
intel_th: gth: Factor out trace start/stop
intel_th: msu: Factor out pipeline draining
intel_th: msu: Switch over to scatterlist
intel_th: msu: Replace open-coded list_{first,last,next}_entry variants
intel_th: Only report useful IRQs to subdevices
intel_th: msu: Start handling IRQs
intel_th: pci: Use MSI interrupt signalling
intel_th: Communicate IRQ via resource
intel_th: Add "rtit" source device
intel_th: Skip subdevices if their MMIO is missing
intel_th: Rework resource passing between glue layers and core
intel_th: SPDX-ify the documentation
intel_th: msu: Fix single mode with IOMMU
coresight: funnel: Support static funnel
dt-bindings: arm: coresight: Unify funnel DT binding
coresight: replicator: Add new device id for static replicator
...
|
|
Clang warns:
drivers/thunderbolt/tunnel.c:504:17: warning: implicit truncation from
'int' to bit-field changes value from 5 to -3
[-Wbitfield-constant-conversion]
path->priority = 5;
^ ~
1 warning generated.
The priority member in struct tb_path is only ever assigned a positive
number:
$ rg -n priority drivers/thunderbolt/path.c
drivers/thunderbolt/tunnel.c:99: path->priority = 3;
drivers/thunderbolt/tunnel.c:308: path->priority = 2;
drivers/thunderbolt/tunnel.c:323: path->priority = 1;
drivers/thunderbolt/tunnel.c:504: path->priority = 5;
Furthermore, that value is only assigned to an unsigned integer in
tb_path_activate (the priority member in struct tb_regs_hop).
Fixes: 44242d6c9703 ("thunderbolt: Add support for DMA tunnels")
Link: https://github.com/ClangBuiltLinux/linux/issues/454
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The flags field in 'struct shash_desc' never actually does anything.
The only ostensibly supported flag is CRYPTO_TFM_REQ_MAY_SLEEP.
However, no shash algorithm ever sleeps, making this flag a no-op.
With this being the case, inevitably some users who can't sleep wrongly
pass MAY_SLEEP. These would all need to be fixed if any shash algorithm
actually started sleeping. For example, the shash_ahash_*() functions,
which wrap a shash algorithm with the ahash API, pass through MAY_SLEEP
from the ahash API to the shash API. However, the shash functions are
called under kmap_atomic(), so actually they're assumed to never sleep.
Even if it turns out that some users do need preemption points while
hashing large buffers, we could easily provide a helper function
crypto_shash_update_large() which divides the data into smaller chunks
and calls crypto_shash_update() and cond_resched() for each chunk. It's
not necessary to have a flag in 'struct shash_desc', nor is it necessary
to make individual shash algorithms aware of this at all.
Therefore, remove shash_desc::flags, and document that the
crypto_shash_*() functions can be called from any context.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Titan Ridge flow to start the firmware is the same as Alpine Ridge so we
can do the same on Titan Ridge based Apple systems.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
While tb_dump_hop() prints out necessary information it is in format
that is quite hard to read from the logs especially when one needs to
follow the path to see that the setup is correct.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Now that the driver can handle every possible tunnel types there is no
point to log everything as info level so turn these to happen at debug
level instead.
While at it remove duplicated tunnel activation log message
(tb_tunnel_activate() calls tb_tunnel_restart() which print the same
message) and add one missing '\n' termination.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The printing macros do not modify the passed object so make them
const. While there make tb_route() to take const parameter as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Two domains (hosts) can be connected through a Thunderbolt cable and in
that case they can start software services such as networking over the
high-speed DMA paths. Now that we have all the basic building blocks in
place to create DMA tunnels over the Thunderbolt fabric we can add this
support to the software connection manager as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In order to detect possible connections to other domains we need to be
able to find out why tb_switch_alloc() fails so make it return ERR_PTR()
instead. This allows the caller to differentiate between errors such as
-ENOMEM which comes from the kernel and for instance -EIO which comes
from the hardware when trying to access the possible switch.
Convert all the current call sites to handle this properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In addition to PCIe and Display Port tunnels it is also possible to
create tunnels that forward DMA traffic from the host interface adapter
(NHI) to a NULL port that is connected to another domain through a
Thunderbolt cable. These tunnels can be used to carry software messages
such as networking packets.
To support this we introduce another tunnel type (TB_TUNNEL_DMA) that
supports paths from NHI to NULL port and back.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently ICM has been handling XDomain UUID exchange so there was no
need to have it in the driver yet. However, since now we are going to
add the same capabilities to the software connection manager it needs to
be handled properly.
For this reason modify the driver XDomain protocol handling so that if
the remote domain UUID is not filled in the core will query it first and
only then start the normal property exchange flow.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We run all XDomain requests during discovery in tb->wq and since it only
runs one work at the time it means that sending back reply to the other
domain may be delayed too much depending whether there is an active
XDomain discovery request running.
To make sure we can send reply to the other domain as soon as possible
run tb_xdp_handle_request() in system workqueue instead. Since the
device can be hot-removed in the middle we need to make sure the domain
structure is still around when the function is run so increase reference
count before we schedule the reply work.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Now that we have capability to discover existing tunnels during driver
load there is no point tearing down tunnels when the driver gets
unloaded. Instead we can just leave them running. If user disconnects
devices while there is no Thunderbolt driver loaded, tunneled protocol
hotplug happens and is handled by the corresponding driver (pciehp in
case of PCIe tunnel, GFX driver in case of DP tunnel).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
NFC (non flow control) credits is actually 20-bit field so update
tb_port_add_nfc_credits() to handle this properly. This allows us to set
NFC credits for Display Port path in subsequent patches.
Also make sure the function does not update the hardware if the
underlying switch is already unplugged.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We will be needing these routines to find Display Port adapters as well
so modify them to take port type as the second parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The only way to expand Thunderbolt topology is through the NULL adapter
ports (typically ports 1, 2, 3 and 4). There is no point handling
Thunderbolt hotplug events on any other port.
Add a helper function (tb_port_is_null()) that can be used to determine
if the port is NULL port, and use it in software connection manager code
when hotplug event is handled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently the software connection manager (tb.c) has only supported
creating a single PCIe tunnel, no PCIe device daisy chaining has been
supported so far. This updates the software connection manager so that
it now can create PCIe tunnels for full chain of six devices.
Because PCIe allows DMA and opens possibility for DMA attacks we change
security level to "user" meaning that PCIe tunneling requires that the
userspace authorizes the devices first. This makes it possible to block
PCIe tunneling completely while still allowing other types of tunnels to
be automatically created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In Apple Macs the boot firmware (EFI) connects all devices automatically
when the system is started, before it hands over to the OS. Instead of
ignoring we discover all those PCIe tunnels and record them using our
internal structures, just like we do when a device is connected after
the OS is already up.
By doing this we can properly tear down tunnels when devices are
disconnected. Also this allows us to resume the existing tunnels after
system suspend/resume cycle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
State of the connected devices and tunnel configuration is not known
during resume. For example some paths may not be complete anymore if the
user has unplugged the related devices. So instead of marking all paths
as inactive we go ahead and deactivate them explicitly before we restart
them.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Now that we can allocate hop IDs per port on a path, we can take
advantage of this and create tunnels covering longer paths than just
between two adjacent switches. PCIe actually does not need this as it
is typically a daisy chain between two adjacent switches but this way we
do not need to hard-code creation of the tunnel.
While there add name to struct tb_path to make debugging easier, and
update kernel-doc comments.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We need to be able to walk from one port to another when we are creating
paths where there are multiple switches between two ports. For this
reason introduce a new function tb_next_port_on_path().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
|
|
Currently the driver only assigns remote port for the primary port if in
case of dual link. This makes things such as walking from one port to
another more complex than necessary because the code needs to change
from secondary to primary port if the path that is established is
created using secondary links.
In order to always assign both remote pointers we need to prevent the
scanning code from following the secondary link. Failing to do that
might cause problems as the same switch may be enumerated twice (or
removed in case of unplug). Handle that properly by introducing a new
function tb_port_has_remote() that returns true only for the primary
port. We also update tb_is_upstream_port() to support both dual link
ports, make it take const port pointer and move it below
tb_upstream_port() to keep similar functions close.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Each port has a separate path configuration space that is used for
finding the next hop (switch) in the path. HopID is an index to this
configuration space. HopIDs 0 - 7 are reserved by the protocol.
In order to get next available HopID for each direction we provide two
pairs of helper functions that can be used to allocate and release
HopIDs for a given port.
While there remove obsolete TODO comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.
We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In order to tunnel non-PCIe traffic as well rename tunnel_pci.[ch] to
tunnel.[ch] to reflect this fact. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The adapter specific capability either is there or not if the port does
not hold an adapter. Instead of always finding it on-demand we read the
offset just once when the port is initialized.
While there we update the struct port documentation to follow kernel-doc
format.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We need to wait until all buffers have been drained before the path can
be considered disabled. Do this for every hop in a path.
This adds another bit field to struct tb_regs_hop even if we are trying
to get rid of them but we can clean them up another day.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Thunderbolt 2 devices and beyond link controller needs to be notified
when a switch is going to be suspended by setting bit 31 in LC_SX_CTRL
register. Add this functionality to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Thunderbolt 2 devices and beyond need to have additional bits set in
link controller specific registers. This includes two bits in LC_SX_CTRL
that tell the link controller which lane is connected and whether it is
upstream facing or not.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We will be adding more link controller functionality in subsequent
patches and it does not make sense to keep all that in switch.c, so
separate LC functionality into its own file.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Light Ridge has an issue where reading the next capability pointer
location in port config space the read data is not cleared. It is fine
to read capabilities each after another so only thing we need to do is
to make sure we issue dummy read after tb_port_find_cap() is finished to
avoid the issue in next read.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Light Ridge and Eagle Ridge both need to have TMU access enabled before
port space can be fully accessed so make sure it happens on those. This
allows us to get rid of the offset quirk in tb_port_find_cap().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Maximum depth in Thunderbolt topology is 6 so make sure it is not
possible to allocate switches that exceed the depth limit.
While at it update tb_switch_alloc() to use upper/lower_32_bits()
following tb_switch_alloc_safe_mode().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
switch_lock was introduced because it allowed serialization of device
authorization requests from userspace without need to take the big
domain lock (tb->lock). This was fine because device authorization with
ICM is just one command that is sent to the firmware. Now that we start
to handle all tunneling in the driver switch_lock is not enough because
we need to walk over the topology to establish paths.
For this reason drop switch_lock from the driver completely in favour of
big domain lock.
There is one complication, though. If userspace is waiting for the lock
in tb_switch_set_authorized(), it keeps the device_del() from removing
the sysfs attribute because it waits for active users to release the
attribute first which leads into following splat:
INFO: task kworker/u8:3:73 blocked for more than 61 seconds.
Tainted: G W 5.1.0-rc1+ #244
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u8:3 D12976 73 2 0x80000000
Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt]
Call Trace:
? __schedule+0x2e5/0x740
? _raw_spin_lock_irqsave+0x12/0x40
? prepare_to_wait_event+0xc5/0x160
schedule+0x2d/0x80
__kernfs_remove.part.17+0x183/0x1f0
? finish_wait+0x80/0x80
kernfs_remove_by_name_ns+0x4a/0x90
remove_files.isra.1+0x2b/0x60
sysfs_remove_group+0x38/0x80
sysfs_remove_groups+0x24/0x40
device_remove_attrs+0x3d/0x70
device_del+0x14c/0x360
device_unregister+0x15/0x50
tb_switch_remove+0x9e/0x1d0 [thunderbolt]
tb_handle_hotplug+0x119/0x5a0 [thunderbolt]
? process_one_work+0x1b7/0x420
process_one_work+0x1b7/0x420
worker_thread+0x37/0x380
? _raw_spin_unlock_irqrestore+0xf/0x30
? process_one_work+0x420/0x420
kthread+0x118/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x35/0x40
We deal this by following what network stack did for some of their
attributes and use mutex_trylock() with restart_syscall(). This makes
userspace release the attribute allowing sysfs attribute removal to
progress before the write is restarted and eventually fail when the
attribute is removed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
If switch is already disconnected there is no point sending it commands
and waiting for timeout. Instead in that case return error immediately.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
tb_switch_find_by_route() does the same already so use it instead and
remove duplicated get_switch_at_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
|
|
This field is not used anywhere so remove it.
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
uuid in add_switch is allocted via kmemdup which can fail. The patch
logs the error and cleans up the allocated memory for switch.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
No check is enforced for the return value of kzalloc,
which may lead to NULL-pointer dereference.
The patch fixes this issue.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|