| Age | Commit message (Collapse) | Author |
|---|
|
commit a73d2e30b46787d478275db36c19222020e29dc5 upstream.
The AS3722_GPIO_INV bit will always be blindly overwritten by
as3722_pinctrl_gpio_set_direction() and will be ignored when
setting the value of the GPIO in as3722_gpio_set() since the
enable_gpio_invert flag is never set. This will cause an
initially inverted GPIO to toggle when requested as an output,
which could be problematic if, for example, the GPIO controls
a critical regulator.
Instead of setting up the enable_gpio_invert flag, just leave
the invert bit alone and check it before setting the GPIO value.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
|
|
commit 655dada6277991 causes kernel panic, this patch fixes it.
[ 1.197816] [ffffffee] *pgd=0d7fd821, *pte=00000000, *ppte=00000000
[ 1.204070] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 1.209447] Modules linked in:
[ 1.212490] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.0-rc1 #3
[ 1.218737] task: cd03c000 ti: cd040000 task.ti: cd040000
[ 1.224127] PC is at gpiod_lock_as_irq+0xc/0x64
[ 1.228634] LR is at sirfsoc_gpio_irq_startup+0x18/0x44
[ 1.233842] pc : [<c01d3990>] lr : [<c01d1c38>] psr: a0000193
[ 1.233842] sp : cd041d30 ip : 00000000 fp : 00000000
[ 1.245296] r10: 00000000 r9 : cd023db4 r8 : 60000113
[ 1.250505] r7 : 0000003e r6 : cd023dd4 r5 : c06bfa54 r4 : cd023d80
[ 1.257014] r3 : 00000020 r2 : 00000000 r1 : ffffffea r0 : ffffffea
[ 1.263526] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 1.270903] Control: 10c53c7d Table: 00004059 DAC: 00000015
[ 1.276631] Process swapper/0 (pid: 1, stack limit = 0xcd040240)
[ 1.282620] Stack: (0xcd041d30 to 0xcd042000)
[ 1.286963] 1d20: cd023d80 c01d1c38 c01d1c20 cd023d80
[ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c
[ 1.286963] 1d20: cd023d80 c01d1c38 c01d1c20 cd023d80
[ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c
[ 1.295124] 1d40: 00000001 c0068438 cd023d80 ccb6d880 cd023dd4 c0067044 0000718e c006719c
[ 1.303283] 1d60: 00000800 00000083 ccb6d880 cd023d80 c02b41d8 00000083 0000003e ccb7c410
[ 1.311442] 1d80: 00000000 c00671dc 00000083 0000003e c02b41d8 cd3dd5c0 0000003e ccb7c634
[ 1.319601] 1da0: cd040030 c00672a8 cd3dd5c0 ccb7c410 ccb6d340 ccb7c410 ccb6d340 cd3dd400
[ 1.327760] 1dc0: cd3dd410 c02b4434 ccb7c410 c01265a8 00000001 cd3dd410 c0687108 00000000
[ 1.335919] 1de0: c0687108 00000000 00000000 c0240170 c0240158 cd3dd410 c06c30d0 c023e8bc
[ 1.344079] 1e00: c023e9d4 00000000 cd3dd410 c023e9d4 c0682150 c023cf88 cd003e98 cd2d50c4
[ 1.352238] 1e20: cd3dd410 cd3dd444 c06822f0 c023e768 cd3dd418 cd3dd410 c06822f0 c023de14
[ 1.360397] 1e40: cd3dd418 00000000 cd3dd410 c023c398 cd041e78 cd041ea8 cd3dd400 cd3dd410
[ 1.368556] 1e60: 00000083 00000000 cd3dd400 cd3dd410 00000083 000000c8 c04e00c8 c023fee8
[ 1.376715] 1e80: 00000000 cd041ea8 cd3dd400 00000001 00000083 c024048c c0435ef8 c0434dec
[ 1.384874] 1ea0: c068da58 c04c6d04 c0682150 c0435ef8 ffffffff 00000000 00000000 c068da58
[ 1.393033] 1ec0: 00000020 00000000 00000000 00000000 c05dabb8 00000007 c068d640 c068d640
[ 1.401193] 1ee0: c04c247c c04c249c 00000000 c00088e8 cd004c00 c043bbb8 cd029180 c03812a0
[ 1.409352] 1f00: 00000000 00000000 60000113 c0673728 60000113 c0673728 00000000 00000000
[ 1.417511] 1f20: cd7fce01 c0390a54 00000065 c003a81c c049e8bc 00000007 cd7fce0e 00000007
[ 1.425670] 1f40: 00000000 c05dabb8 00000007 c068d640 c068d640 c04c050c c04e00c8 00000065
[ 1.433829] 1f60: c04e00c0 c04c0c54 00000007 00000007 c04c050c c037d8fc cd03c000 c004322c
[ 1.441988] 1f80: c0662b40 0000d640 c03737c0 00000000 00000000 00000000 00000000 00000000
[ 1.450147] 1fa0: 00000000 c03737cc 00000000 c000e478 00000000 00000000 00000000 00000000
[ 1.458307] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.466467] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 0002d481 05014092
[ 1.474640] [<c01d3990>] (gpiod_lock_as_irq) from [<c01d1c38>] (sirfsoc_gpio_irq_startup+0x18/0x44)
[ 1.483661] [<c01d1c38>] (sirfsoc_gpio_irq_startup) from [<c0068438>] (irq_startup+0x34/0x6c)
[ 1.492163] [<c0068438>] (irq_startup) from [<c0067044>] (__setup_irq+0x450/0x4b8)
[ 1.499714] [<c0067044>] (__setup_irq) from [<c00671dc>] (request_threaded_irq+0xa8/0x128)
[ 1.507960] [<c00671dc>] (request_threaded_irq) from [<c00672a8>] (request_any_context_irq+0x4c/0x7c)
[ 1.517164] [<c00672a8>] (request_any_context_irq) from [<c02b4434>] (gpio_extcon_probe+0x144/0x1d4)
[ 1.526279] [<c02b4434>] (gpio_extcon_probe) from [<c0240170>] (platform_drv_probe+0x18/0x48)
[ 1.534783] [<c0240170>] (platform_drv_probe) from [<c023e8bc>] (driver_probe_device+0x120/0x238)
[ 1.543641] [<c023e8bc>] (driver_probe_device) from [<c023cf88>] (bus_for_each_drv+0x58/0x8c)
[ 1.552143] [<c023cf88>] (bus_for_each_drv) from [<c023e768>] (device_attach+0x74/0x88)
[ 1.560126] [<c023e768>] (device_attach) from [<c023de14>] (bus_probe_device+0x84/0xa8)
[ 1.568113] [<c023de14>] (bus_probe_device) from [<c023c398>] (device_add+0x440/0x520)
[ 1.576012] [<c023c398>] (device_add) from [<c023fee8>] (platform_device_add+0xb4/0x214)
[ 1.584084] [<c023fee8>] (platform_device_add) from [<c024048c>] (platform_device_register_full+0xb8/0xdc)
[ 1.593719] [<c024048c>] (platform_device_register_full) from [<c04c6d04>] (sirfsoc_init_late+0xec/0xf4)
[ 1.603185] [<c04c6d04>] (sirfsoc_init_late) from [<c04c249c>] (init_machine_late+0x20/0x28)
[ 1.611603] [<c04c249c>] (init_machine_late) from [<c00088e8>] (do_one_initcall+0xf8/0x144)
[ 1.619934] [<c00088e8>] (do_one_initcall) from [<c04c0c54>] (kernel_init_freeable+0x13c/0x1dc)
[ 1.628620] [<c04c0c54>] (kernel_init_freeable) from [<c03737cc>] (kernel_init+0xc/0x118)
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix the SD1_CLK handling for r8a7791. Without this patch
it is impossible to request all pins needed for SDHI1 on
the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Modular builds of pinctrl-msm break due to handle_bad_irq being
unexported for module use. For now, make PINCTRL_MSM 'bool'.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixing setting the interrupt type for eints >= 8.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On tha Allwinner A20 SoC, the external interrupts on the pin controller
device are connected to the GIC. Without chained_irq_{enter, exit},
external GPIO interrupts, such as used by mmc core card detect, cause
the system to hang.
This issue was first encountered during my attempt to get out-of-band
interrupts for WiFi on the Cubietruck working. With David's new series
of sunci-mci using mmc slot-gpio for (GPIO interrupt based) card
detection, removing the SD card also causes my Cubietruck to hang. This
problem should extend to all Allwinner A20 based boards.
With this fix, the system no longer hangs when I remove or insert the
SD card. /proc/interrupts show that the interrupt has correctly fired.
However the system still does not detect card removal/insertion. I
believe this is another unrelated issue.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Bring the driver in line with the bcm-based dt name for pinctrl.
This is being done to keep consistency with other Broadcom mobile
SoC drivers.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
|
|
When memory allocation failed, drive should return error as ENOMEM.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit c420619 "pinctrl: pinconf: remove checks on ops->pin_config_get"
removed the check on (ops != NULL) when performing pinconf_pins_show() or
pinconf_groups_show(). As these entries are always enabled, even if
pinconf is not supported, reading will result in an oops due to NULL
ops.
Instead of checking for ops, remove the corresponding debugfs entries if
pinconf and/or pinmux are not implemented.
Tested on OMAP3 (pinctrl-single).
Cc: stable@vger.kernel.org
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We have few fedora bug reports about list corruption on pinctrl,
for example:
https://bugzilla.redhat.com/show_bug.cgi?id=1051918
Most likely corruption happen due lack of protection of pinctrl_list
when adding new nodes to it. Patch corrects that.
Fixes: 42fed7ba44e ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
according to datasheet and ac97_muxmask assignment, ac97_pins should be
corrected.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The offset for the 2bit register calculate wrong, this patch
fixes the problem. The debugfs printout for oconf, iconfa, iconfb
now shows the real values.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Due to an assumption in the VT8500 pinctrl driver, the value passed
from devicetree for 'wm,pull' was not explicitly translated before
being passed to pinconf.
Since v3.10, changes to 'enum pin_config_param', PIN_CONFIG_BIAS_PULL_(UP/DOWN)
no longer map 1-to-1 with the expected values in devicetree.
This patch adds a small translation between the devicetree values (0..2)
and the enum pin_config_param equivalent values.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The offset to ICONFB was incorrect, this patch set the correct value 0x14.
dev_dbg in function imx1_write_2bit print the wrong address and had been
moved after address calculation.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When setting the gpio irq type, use the __irq_set_handler_locked()
variant instead of the irq_set_handler() to prevent false
spinlock recursion warning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # v3.12
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
|
|
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull bulk pin control changes from Linus Walleij:
"This has been queued and tested for a while. Lots of action here,
like in the GPIO tree, embedded stuff like this is really hot now it
seems. Details in the signed tag. I'm especially happy about the
Qualcomm driver as it is used in such a huge subset of mobile handsets
out there, and these platforms in general need better upstream support
- New driver for the Qualcomm TLMM pin controller and its msm8x74
subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and GPIO
drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC" driver
and associated subdrivers as usual. It is settling down a little
bit now it seems.
- Minor fixes and incremental updates here and there as usual"
* tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sunxi: Honor GPIO output initial vaules
pinctrl: capri: add dependency on OF
ARM: bcm11351: Enable pinctrl for Broadcom Capri SoCs
ARM: pinctrl: Add Broadcom Capri pinctrl driver
pinctrl: Add pinctrl binding for Broadcom Capri SoCs
pinctrl: Add void * to pinctrl_pin_desc
pinctrl: st: Fix a typo in probe
pinctrl: Fix some typos and grammar issues in the documentation
pinctrl: sirf: lock IRQs when starting them
pinctrl: sirf: put gpio interrupt pin into input status automatically
pinctrl: sirf: use only one irq_domain for the whole device node
pinctrl: single: fix infinite loop caused by bad mask
pinctrl: single: fix pcs_disable with bits_per_mux
pinctrl: single: fix DT bindings documentation
pinctrl: as3722: Set pin to output mode for some function
pinctrl: sirf: add pin group for USP0 with only RX or TX frame sync
pinctrl: sirf: fix the pins of sdmmc5 connected with TriG
pinctrl: sirf: add lost usp1_uart_nostreamctrl group for atlas6
pinctrl: sunxi: Add Allwinner A20 clock output pin functions
pinctrl/lantiq: fix typo
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
|
|
This deletes the special AB8500 GPIO platform data passing
header and merges the few remaining contents down into the
abx500 pinctrl driver which handles the abx500 GPIO device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
All instances of this device are now coming from device tree-
enabled platforms probing without using platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some GPIO users, such as fixed-regulator, request GPIO output with
initial value of 1. This was ignored by sunxi driver.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit f6308b36c411 (ACPI: Add BayTrail SoC GPIO and LPSS
ACPI IDs), because it causes the Alan Cox' ASUS T100TA to "crash and
burn" during boot if the Baytrail pinctrl driver is compiled in.
Fixes: f6308b36c411 (ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs)
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As this driver is using pinconf_generic_dt_node_to_map_pin() it
needs to depend on OF so as not to cause build problems on
archs that do not support OF.
Cc: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Probe function had commas instead of semi-colons on some of the lines.
This patch just fixes those lines. No functional chagnes done in this
patch.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.
Also assign the gpio_chip.dev pointer to be used for error
messages.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
busses like i2c, spi and so on can parse the virq of their subnode automatically by
irq_of_parse_and_map(). for example, i2c will do that in of_i2c_register_devices().
people can put hwirq number attached to a gpio controller in dts, and drivers can
directly request the parsed virq.
for example, for an i2c client as below,
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
interrupt-parent = <&gpio>;
interrupts = <3 0>;
reg = <0x5c>;
};
in i2c client probe(), it will request_irq(client->irq, ...) without
calling gpio_direction_input().
so here when we set irq type, we also put the pin to input direction.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
in sirfsoc gpio probe(), we create 5 irq_domains for 5 gpio banks. but
in irq_create_of_mapping() of irqchip core level, irq_find_host() can
only return the 1st irq_domain attached the pinctrl dt device node as
we can see from the codes:
unsigned int irq_create_of_mapping(struct device_node *controller,
const u32 *intspec, unsigned int intsize)
{
struct irq_domain *domain;
...
domain = controller ? irq_find_host(controller) : irq_default_domain;
}
struct irq_domain *irq_find_host(struct device_node *node)
{
struct irq_domain *h, *found = NULL;
int rc;
/* We might want to match the legacy controller last since
* it might potentially be set to match all interrupts in
* the absence of a device node. This isn't a problem so far
* yet though...
*/
mutex_lock(&irq_domain_mutex);
list_for_each_entry(h, &irq_domain_list, link) {
if (h->ops->match)
rc = h->ops->match(h, node);
else
rc = (h->of_node != NULL) && (h->of_node == node);
if (rc) {
found = h;
break;
}
}
mutex_unlock(&irq_domain_mutex);
return found;
}
for sirfsoc, the 1st irq_domain attached to the device_node(controller) only
can do linear for the 1st 32 gpios. so for devices who use gpio hwirq above
32 and put the information in dt like:
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
+ interrupt-parent = <&gpio>;
+ interrupts = <34 0>;
};
we will fail to get the virq for these devices as hwirq will be bigger than
domain->revmap_data.linear.size in:
unsigned int irq_linear_revmap(struct irq_domain *domain,
irq_hw_number_t hwirq)
{
/* Check revmap bounds; complain if exceeded */
if (WARN_ON(hwirq >= domain->revmap_data.linear.size))
return 0;
return domain->revmap_data.linear.revmap[hwirq];
}
this patch drops redundant irq_domain and keep only one to fix the problem.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
commit 4e7e8017a80e1 (pinctrl: pinctrl-single:
enhance to configure multiple pins of different modules) improved
support for pinctrl-single,bits option, but also caused a regression
in parsing badly configured mask data.
If the masks in DT data are not quite right,
pcs_parse_bits_in_pinctrl_entry() can end up in an infinite loop,
trashing memory at the same time.
Add a check to verify that each loop actually removes bits from the
'mask', so that the loop can eventually end.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pcs_enable() uses vals->mask instead of pcs->fmask when bits_per_mux is
enabled. However, pcs_disable() always uses pcs->fmask.
Fix pcs_disable() to use vals->mask with bits_per_mux.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If pins are used for function output like pwm, clk32k,
power good etc then set it as output mode default.
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sdmmc5 has only 3 pins CMD, CLK, DATA which are connected with CSR
TriG RF multi-GNSS. The hardware connection is like:
DATA -- GPS_SGN
CLK -- GPS_RF_CLK
CMD -- GPS_MAG
here we drop redundant pins in sdmmc5 group.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
commit af614b2301f0e304 adds lost USP-based UART pin groups for prima2,
but missed usp1_uart_nostreamctrl group for atlas6, this patch fixes it.
this makes USP(Universal Serial Ports) port1 can work as uart without
stream ctrl.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds the clock output pin functions on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Antonios Vamporakis <ant@area128.com>
CC: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds I2C[0-4] pinmux support to R8A7791 SoC.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds VIN[0-2] pinmux support to r8a7791 SoC.
VIN1 B mirror is also added along with the primary
configuration since it's the only one that provides
access to all 24 data bits on VIN1.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This groups USB PWEN and OVC pins together on R8A7791 SoC,
the same way it's done on R8A7790, since both are needed
for a USB device.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixes a typo in the vin3_sync_mux array (s/VI2/VI3/).
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Third Round of Renesas ARM Based SoC DT Updates for v3.14
* r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCSs
- Add SSI, QSPI and MSIOF clocks in device tree
r8a7791 (R-Car M2) based Koelsch and r8a7790 (R-Car H2) based Lager boards
- Remove reference DTS
- Specify external clock frequency in DT
- Sync non-reference DTS with referene DTS
- Add clocks to DTS
* r8a7740 (R-Mobile A1) based Armadillo board
- Add gpio-keys device
- Add PWM backlight enable GPIO
- Add PWM backlight power supply
* r8a73a0 (SH-Mobile AG5), r8a7740 (R-Mobile A1) and
r8a73a4 (SH-Mobile APE6) SoCs
- Specify PFC interrupts in DT
* tag 'renesas-dt3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (72 commits)
ARM: shmobile: r8a7791: Add SSI clocks in device tree
ARM: shmobile: r8a7790: Add SSI clocks in device tree
ARM: shmobile: r8a7791: Add QSPI module clock in device tree
ARM: shmobile: r8a7790: Add QSPI module clock in device tree
ARM: shmobile: r8a7791: Add MSIOF clocks in device tree
ARM: shmobile: r8a7790: Add MSIOF clocks in device tree
ARM: shmobile: Remove Koelsch reference DTS
ARM: shmobile: Remove Lager reference DTS
ARM: shmobile: koelsch: Specify external clock frequency in DT
ARM: shmobile: lager: Specify external clock frequency in DT
ARM: shmobile: Sync Koelsch DTS with Koelsch reference DTS
ARM: shmobile: Sync Lager DTS with Lager reference DTS
ARM: shmobile: r8a7791: Add clocks
ARM: shmobile: r8a7790: Reference clocks
ARM: shmobile: r8a7790: Add clocks
ARM: shmobile: armadillo: dts: Add gpio-keys device
ARM: shmobile: sh73a0: Specify PFC interrupts in DT
ARM: shmobile: r8a7740: Specify PFC interrupts in DT
ARM: shmobile: r8a73a4: Specify PFC interrupts in DT
ARM: shmobile: armadillo: dts: Add PWM backlight enable GPIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* powercap:
powercap / RAPL: add support for ValleyView Soc
* acpi-lpss:
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
|
|
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The arrays are never modified, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Andrew Bresticker
Linus Torvalds
Barry Song
Magnus Damm
Josh Cartwright
Hans de Goede
Chen-Yu Tsai
Christian Daudt
Laxman Dewangan
Florian Vaussard
Stanislaw Gruszka
Qipan Li
Chris Ruehl
Tony Prisk
Nicolas Ferre
Linus Walleij
Rafael J. Wysocki
Sherman Yin
Srinivas Kandagatla
Tomi Valkeinen
Mallikarjun Kasoju
Mika Westerberg
Rongjun Ying
Bin Shi
Antonios Vamporakis
Valentine Barshak
Olof Johansson
Laurent Pinchart