| Age | Commit message (Collapse) | Author |
|---|
|
commit 9db8dc6d0785225c42a37be7b44d1b07b31b8957 upstream.
Some PCI bridges implement BARs in addition to bridge windows. For
example, here's a PLX switch:
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI
Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 30, NUMA node 0
Memory at 90a00000 (32-bit, non-prefetchable) [size=256K]
Bus: primary=04, secondary=05, subordinate=0a, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: 90000000-909fffff
Prefetchable memory behind bridge: 0000380000800000-0000380000bfffff
Previously, when the kernel assigned resource addresses (with the
pci=realloc command line parameter, for example) it could clear the struct
resource corresponding to the BAR. When this happened, lspci would report
this BAR as "ignored":
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [size=256K]
This is because the kernel reports a zero start address and zero flags
in the corresponding sysfs resource file and in /proc/bus/pci/devices.
Investigation with 'lspci -x', however, shows the BIOS-assigned address
will still be programmed in the device's BAR registers.
It's clearly a bug that the kernel lost track of the BAR value, but in most
cases, this still won't result in a visible issue because nothing uses the
memory, so nothing is affected. However, when an IOMMU is in use, it will
not reserve this space in the IOVA because the kernel no longer thinks the
range is valid. (See dmar_init_reserved_ranges() for the Intel
implementation of this.)
Without the proper reserved range, a DMA mapping may allocate an IOVA that
matches a bridge BAR, which results in DMA accesses going to the BAR
instead of the intended RAM.
The problem was in pci_assign_unassigned_root_bus_resources(). When any
resource from a bridge device fails to get assigned, the code set the
resource's flags to zero. This makes sense for bridge windows, as they
will be re-enabled later, but for regular BARs, it makes the kernel
permanently lose track of the fact that they decode address space.
Change pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() so they only clear "res->flags"
for bridge *windows*, not bridge BARs.
Fixes: da7822e5ad71 ("PCI: update bridge resources to get more big ranges when allocating space (again)")
Link: https://lore.kernel.org/r/20200108213208.4612-1-logang@deltatee.com
[bhelgaas: commit log, check for pci_is_bridge()]
Reported-by: Kit Chow <kchow@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
- Cleanup PCI register definitions, typos, etc (Bjorn Helgaas)
- Remove unnecessary use of user-space types in CPER (Bjorn Helgaas)
- Cleanup setup-bus.c comments & whitespace (Nicholas Johnson)
* pci/trivial:
PCI: Cleanup setup-bus.c comments and whitespace
CPER: Remove unnecessary use of user-space types
CPER: Add UEFI spec references
PCI: Fix comment typos
PCI: Cleanup register definition width and whitespace
# Conflicts:
# drivers/pci/pci.c
# drivers/pci/setup-bus.c
|
|
Replace dev_printk(KERN_DEBUG) with dev_info(), etc to be more consistent
with other logging and avoid checkpatch warnings.
The KERN_DEBUG messages could be converted to dev_dbg(), but that depends
on CONFIG_DYNAMIC_DEBUG and DEBUG, and we want most of these messages to
*always* be in the dmesg log.
Link: https://lore.kernel.org/lkml/1555733240-19875-1-git-send-email-mohankumar718@gmail.com
Signed-off-by: Mohan Kumar <mohankumar718@gmail.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Cleanup comments, kernel-doc, coding style. No functional changes
intended; comment and whitespace changes only.
Link: https://lore.kernel.org/lkml/PS2P216MB06427E290A68CDB921FB4B2980250@PS2P216MB0642.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
[bhelgaas: tidy related things throughout the file]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The PCI configuration space header type tells us whether the device is a
bridge, a CardBus bridge, or a normal device, and defines the layout of the
rest of the header (PCI r3.0 sec 6.1, PCIe r4.0 sec 7.5.1.1.9).
When we rely on the header format, e.g., when we're dealing with bridge
windows, we should check the header type, not the class code. The class
code is loosely related to the header type, but is often incorrect and the
spec doesn't actually require it to be related to the header format.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: changelog, keep the PCI_CLASS_BRIDGE_HOST check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pci_bridge_check_ranges() determines whether a bridge supports the optional
I/O and prefetchable memory windows and sets the flag bits in the bridge
resources. This *could* be done once during enumeration except that the
resource allocation code completely clears the flag bits, e.g., in the
pci_assign_unassigned_bridge_resources() path.
The problem with pci_bridge_check_ranges() in the resource allocation path
is that we may allocate resources after devices have been claimed by
drivers, and pci_bridge_check_ranges() *changes* the window registers to
determine whether they're writable. This may break concurrent accesses to
devices behind the bridge.
Add a new pci_read_bridge_windows() to determine whether a bridge supports
the optional windows, call it once during enumeration, remember the
results, and change pci_bridge_check_ranges() so it doesn't touch the
bridge windows but sets the flag bits based on those remembered results.
Link: https://lore.kernel.org/linux-pci/1506151482-113560-1-git-send-email-wangzhou1@hisilicon.com
Link: https://lists.gnu.org/archive/html/qemu-devel/2018-12/msg02082.html
Reported-by: Yandong Xu <xuyandong2@huawei.com>
Tested-by: Yandong Xu <xuyandong2@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Ofer Hayut <ofer@lightbitslabs.com>
Cc: Roy Shterman <roys@lightbitslabs.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
|
|
Currently, a hotplug bridge will be given hpmemsize additional memory
and hpiosize additional io if available, in order to satisfy any future
hotplug allocation requirements.
These calculations don't consider the current memory/io size of the
hotplug bridge/slot, so hotplug bridges/slots which have downstream
devices will be allocated their current allocation in addition to the
hpmemsize value.
This makes for possibly undesirable results with a mix of unoccupied and
occupied slots (ex, with hpmemsize=2M):
02:03.0 PCI bridge: <-- Occupied
Memory behind bridge: d6200000-d64fffff [size=3M]
02:04.0 PCI bridge: <-- Unoccupied
Memory behind bridge: d6500000-d66fffff [size=2M]
This change considers the current allocation size when using the
hpmemsize/hpiosize parameters to make the reservations predictable for
the mix of unoccupied and occupied slots:
02:03.0 PCI bridge: <-- Occupied
Memory behind bridge: d6200000-d63fffff [size=2M]
02:04.0 PCI bridge: <-- Unoccupied
Memory behind bridge: d6400000-d65fffff [size=2M]
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If there is only a single bridge on the bus, we assign all resources to it.
Currently this is done as a part of the resource distribution loop but it
does not have to be there, and moving it outside actually improves
readability because we can then save one indent level in the loop.
While there we can add hotplug_bridges == 1 && normal_bridges == 0 to
the same block because they are dealt the same way.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
|
|
b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add PCI-specific dev_printk() wrappers and use them to simplify the code
slightly. No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: squash into one patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Per ebfdc40969f2 ("checkpatch: attempt to find unnecessary 'out of memory'
messages"), when a memory allocation fails, the memory subsystem emits
generic "out of memory" messages (see slab_out_of_memory() for some of this
logging). Therefore, additional error messages in the caller don't add
much value.
Remove messages that merely report "out of memory".
This preserves some messages that report additional information, e.g.,
allocation failures that mean we drop hotplug events.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[bhelgaas: changelog, squash patches, make similar changes to acpiphp,
cpqphp, ibmphp, keep warning when dropping hotplug event]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
* pci/resource:
PCI: Fail pci_map_rom() if the option ROM is invalid
PCI: Move pci_map_rom() error path
x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)
PCI: Add pci_resize_resource() for resizing BARs
PCI: Add resizable BAR infrastructure
PCI: Add PCI resource type mask #define
|
|
The same problem that we have with bus space applies to other resources
as well. Linux only allocates the minimal amount of resources so that
the devices currently present barely fit there. This prevents extending
the chain later on because the resource windows allocated for hotplug
downstream ports are too small.
Follow what we already did for bus number and assign all available extra
resources to hotplug-capable bridges. This makes it possible to extend the
hierarchy later.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The following pattern is often used:
list_for_each_entry(dev, &bus->devices, bus_list) {
if (pci_is_bridge(dev)) {
...
}
}
Add a for_each_pci_bridge() helper to make that code easier to write and
read by reducing indentation level. It also saves one or few lines of code
in each occurrence.
Convert PCI core parts here at the same time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: fold in http://lkml.kernel.org/r/20171013165352.25550-1-andriy.shevchenko@linux.intel.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a pci_resize_resource() interface to allow device drivers to resize
BARs of their devices.
This is useful for devices with large local storage, e.g., graphics
devices. These devices often only expose 256MB BARs initially to be
compatible with 32-bit systems.
This function only tries to reprogram the windows of the bridge directly
above the requesting device and only the BAR of the same type (usually mem,
64bit, prefetchable). This is done to avoid disturbing other drivers by
changing the BARs of their devices.
Drivers should use the following sequence to resize their BARs:
1. Disable memory decoding of the device using the PCI cfg dword.
2. Use pci_release_resource() to release all BARs which can move during the
resize, including the one you want to resize.
3. Call pci_resize_resource() for each BAR you want to resize.
4. Call pci_assign_unassigned_bus_resources() to reassign new locations
for all BARs which are not resized, but could move.
5. If everything worked as expected, enable memory decoding in the device
again using the PCI cfg dword.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a #define for the PCI resource type mask. We use this mask multiple
times in the bus setup.
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: move to setup-bus.c]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
In case that one device's alignment is greater than its size, we may
get an incorrect size and alignment for its bus's memory window in
pbus_size_mem(). Fix this case.
Signed-off-by: Yongji Xie <elohimes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove res_to_dev_res() debug message. This is printed from a lookup
function. If the message is important, it should be printed from the
caller with more context.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
|
Some PCI root bridges don't have a corresponding ACPI device.
This can be the case on some old platforms. Don't call acpi_ioapic_add()
on these bridges because they can't support ioapic hotplug.
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bhelgaas@google.com
Cc: helgaas@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1473522046-31329-1-git-send-email-rui.y.wang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
IOAPICs present during system boot aren't added to ioapic_list,
thus are unable to be hot-removed. Fix it by calling
acpi_ioapic_add() during root bus enumeration.
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: helgaas@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1471420837-31003-3-git-send-email-rui.y.wang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Highlights:
- ARM64 support for ACPI host bridges
- new drivers for Axis ARTPEC-6 and Marvell Aardvark
- new pci_alloc_irq_vectors() interface for MSI-X, MSI, legacy INTx
- pci_resource_to_user() cleanup (more to come)
Detailed summary:
Enumeration:
- Move ecam.h to linux/include/pci-ecam.h (Jayachandran C)
- Add parent device field to ECAM struct pci_config_window (Jayachandran C)
- Add generic MCFG table handling (Tomasz Nowicki)
- Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki)
- Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki)
Resource management:
- Add devm_request_pci_bus_resources() (Bjorn Helgaas)
- Unify pci_resource_to_user() declarations (Bjorn Helgaas)
- Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas)
- Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas)
- Make PCI I/O space optional on ARM32 (Bjorn Helgaas)
- Ignore write combining when mapping I/O port space (Bjorn Helgaas)
- Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas)
- Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas)
- Support I/O resources when parsing host bridge resources (Jayachandran C)
- Add helpers to request/release memory and I/O regions (Johannes Thumshirn)
- Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn)
- Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5))
- Add generic pci_bus_claim_resources() (Lorenzo Pieralisi)
- Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
- Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi)
- Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya)
- Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu)
PCI device hotplug:
- Allow additional bus numbers for hotplug bridges (Keith Busch)
- Ignore interrupts during D3cold (Lukas Wunner)
Power management:
- Enforce type casting for pci_power_t (Andy Shevchenko)
- Don't clear d3cold_allowed for PCIe ports (Mika Westerberg)
- Put PCIe ports into D3 during suspend (Mika Westerberg)
- Power on bridges before scanning new devices (Mika Westerberg)
- Runtime resume bridge before rescan (Mika Westerberg)
- Add runtime PM support for PCIe ports (Mika Westerberg)
- Remove redundant check of pcie_set_clkpm (Shawn Lin)
Virtualization:
- Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra)
- Add DMA alias quirk for Adaptec 3805 (Alex Williamson)
- Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake)
- Add ACS quirk for Solarflare SFC9220 (Edward Cree)
MSI:
- Fix PCI_MSI dependencies (Arnd Bergmann)
- Add pci_msix_desc_addr() helper (Christoph Hellwig)
- Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig)
- Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig)
- Provide sensible IRQ vector alloc/free routines (Christoph Hellwig)
- Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig)
Error Handling:
- Bind DPC to Root Ports as well as Downstream Ports (Keith Busch)
- Remove DPC tristate module option (Keith Busch)
- Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg)
Generic host bridge driver:
- Select IRQ_DOMAIN (Arnd Bergmann)
- Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
ACPI host bridge driver:
- Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki)
- Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki)
- Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki)
- Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki)
Altera host bridge driver:
- Check link status before retrain link (Ley Foon Tan)
- Poll for link up status after retraining the link (Ley Foon Tan)
Axis ARTPEC-6 host bridge driver:
- Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann)
- Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel)
- Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel)
Intel VMD host bridge driver:
- Use lock save/restore in interrupt enable path (Jon Derrick)
- Select device dma ops to override (Keith Busch)
- Initialize list item in IRQ disable (Keith Busch)
- Use x86_vector_domain as parent domain (Keith Busch)
- Separate MSI and MSI-X vector sharing (Keith Busch)
Marvell Aardvark host bridge driver:
- Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni)
- Add Aardvark PCI host controller driver (Thomas Petazzoni)
- Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni)
Microsoft Hyper-V host bridge driver:
- Fix interrupt cleanup path (Cathy Avery)
- Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
- Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
NVIDIA Tegra host bridge driver:
- Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren)
- Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren)
- Use lower-case hex consistently for register definitions (Thierry Reding)
- Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding)
- Stop setting pcibios_min_mem (Thierry Reding)
Renesas R-Car host bridge driver:
- Drop gen2 dummy I/O port region (Bjorn Helgaas)
TI DRA7xx host bridge driver:
- Fix return value in case of error (Christophe JAILLET)
Xilinx AXI host bridge driver:
- Fix return value in case of error (Christophe JAILLET)
Miscellaneous:
- Make bus_attr_resource_alignment static (Ben Dooks)
- Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks)
- MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven)
- Make host bridge drivers explicitly non-modular (Paul Gortmaker)"
* tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (125 commits)
PCI: xgene: Make explicitly non-modular
PCI: thunder-pem: Make explicitly non-modular
PCI: thunder-ecam: Make explicitly non-modular
PCI: tegra: Make explicitly non-modular
PCI: rcar-gen2: Make explicitly non-modular
PCI: rcar: Make explicitly non-modular
PCI: mvebu: Make explicitly non-modular
PCI: layerscape: Make explicitly non-modular
PCI: keystone: Make explicitly non-modular
PCI: hisi: Make explicitly non-modular
PCI: generic: Make explicitly non-modular
PCI: designware-plat: Make it explicitly non-modular
PCI: artpec6: Make explicitly non-modular
PCI: armada8k: Make explicitly non-modular
PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency
PCI: Add ACS quirk for Solarflare SFC9220
arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
PCI: aardvark: Add Aardvark PCI host controller driver
dt-bindings: add DT binding for the Aardvark PCIe controller
PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
...
|
|
All PCI resources (bridge windows and BARs) should be inserted in the
iomem_resource and ioport_resource trees so we know what space is occupied
and what is available for other devices. There's nothing arch-specific
about this, but it is currently done by arch-specific code.
Add a generic pci_bus_claim_resources() interface so we can migrate away
from the arch-specific code.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Yinghai Lu <yinghai@kernel.org>
|
|
Currently, PowerPC PowerNV platform utilizes ppc_md.pcibios_fixup(),
which is called for once after PCI probing and resource assignment
are completed, to allocate platform required resources for PCI devices:
PE#, IO and MMIO mapping, DMA address translation (TCE) table etc.
Obviously, it's not hotplug friendly.
This adds weak function pcibios_setup_bridge(), which is called by
pci_setup_bridge(). PowerPC PowerNV platform will reuse the function
to assign above platform required resources to newly plugged PCI devices
during PCI hotplug in subsequent patches.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
include/asm-generic/pci-bridge.h is now empty, so remove every #include of
it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com> (arm64)
|
|
Fix all whitespace issues (missing or needed whitespace) in all files in
drivers/pci. Code is compiled with allyesconfig before and after code
changes and objects are recorded and checked with objdiff and they are not
changed after this commit.
Signed-off-by: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The new Enhanced Allocation (EA) capability support (patches to follow)
creates resources with the IORESOURCE_PCI_FIXED set. During resource
assignment in pci_bus_assign_resources(), IORESOURCE_PCI_FIXED resources
are not given a parent. This, in turn, causes pci_enable_resources() to
fail with a "not claimed" error.
So, in __pci_bus_assign_resources(), for IORESOURCE_PCI_FIXED resources,
try to request the resource from a parent bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean O. Stalley <sean.stalley@intel.com>
|
|
The new Enhanced Allocation (EA) capability support (patches to follow)
creates resources with the IORESOURCE_PCI_FIXED set. Since these resources
cannot be relocated or resized, their alignment is not really defined, and
it is therefore not specified. This causes a problem in pbus_size_mem()
where resources with unspecified alignment are disabled.
So, in pbus_size_mem() skip IORESOURCE_PCI_FIXED resources, instead of
disabling them.
[bhelgaas: folded in "flags & IORESOURCE_PCI_FIXED" fix from David]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean O. Stalley <sean.stalley@intel.com>
|
|
In d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), we store additional alignment in realloc_head and take
this into consideration for assignment.
In __assign_resources_sorted(), we changed dev_res->res->start, then used
resource_start() (which depends on res->start), so the recomputed res->end
was completely bogus. Even if we'd had the correct size, the end would
have been off by one.
Preserve the resource size when we adjust its alignment.
[bhelgaas: changelog]
Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), it stores additional alignment in realloc_head and takes
this into consideration for assignment.
After getting the additional alignment, it reorders the head list so
resources with bigger alignment are ahead of resources with smaller
alignment. It does this by iterating over the head list and inserting
ahead of any resource with smaller alignment. This should be done for the
first occurrence, but the code currently iterates over the whole list.
Fix this by terminating the loop when we find the first smaller resource in
the head list.
[bhelgaas: changelog]
Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
|
|
Export the following symbols so they can be referenced by a PCI host bridge
driver compiled as a kernel loadable module:
pci_common_swizzle
pci_create_root_bus
pci_stop_root_bus
pci_remove_root_bus
pci_assign_unassigned_bus_resources
pci_fixup_irqs
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
When sizing and assigning resources, we divide the resources into two
lists: the requested list and the additional list. We don't consider the
alignment of additional VF(n) BAR space.
This is because the alignment required for the VF(n) BAR space is the size
of an individual VF BAR, not the size of the space for *all* VFs. But we
want additional alignment to support partitioning on PowerNV.
Consider the additional IOV BAR alignment when sizing and assigning
resources. When there is not enough system MMIO space to accomodate both
the requested list and the additional list, the PF's IOV BAR alignment will
not contribute to the bridge. When there is enough system MMIO space for
both lists, the additional alignment will contribute to the bridge.
The additional alignment is stored in the min_align of pci_dev_resource,
which is stored in the additional list by add_to_list() at the end of
pbus_size_mem(). The additional alignment is calculated in
pci_resource_alignment(). For an IOV BAR, we have arch dependent function
to get the alignment for different arch.
[bhelgaas: changelog, printk cast]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add pci_claim_bridge_resource() to claim a PCI-PCI bridge window. This is
like regular pci_claim_resource(), except that if we fail to claim the
window, we check to see if we can reduce the size of the window and try
again.
This is for scenarios like this:
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff]
pci 0000:00:01.0: bridge window [mem 0xbdf00000-0xddefffff 64bit pref]
pci 0000:01:00.0: reg 0x10: [mem 0xc0000000-0xcfffffff pref]
The 00:01.0 window is illegal: it starts before the host bridge window, so
we have to assume the [0xbdf00000-0xbfffffff] region is inaccessible. We
can make it legal by clipping it to [mem 0xc0000000-0xddefffff 64bit pref].
Previously we discarded the 00:01.0 window and tried to reassign that part
of the hierarchy from scratch. That is a problem because Linux doesn't
always assign things optimally. For example, in this case, BIOS put the
01:00.0 device in a prefetchable window below 4GB, but after 5b28541552ef,
Linux puts the prefetchable window above 4GB where the 32-bit 01:00.0
device can't use it.
Clipping the 00:01.0 window is less intrusive than completely reassigning
things and is sufficient to let us use most of the BIOS configuration. Of
course, it's possible that devices below 00:01.0 will no longer fit. If
that's the case, we'll have to reassign things. But that's a separate
problem.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
|
|
pci_setup_bridge_io(), pci_setup_bridge_mmio(), and
pci_setup_bridge_mmio_pref() program the windows of PCI-PCI bridges.
Previously they accepted a pointer to the pci_bus of the secondary bus,
then looked up the bridge leading to that bus. Pass the bridge directly,
which will make it more convenient for future callers.
No functional change.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
|
|
In 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to
64-bit resources"), we added IORESOURCE_MEM_64 to the mask in
pci_assign_unassigned_root_bus_resources(), but not to the mask in
pci_assign_unassigned_bridge_resources().
Add IORESOURCE_MEM_64 to the pci_assign_unassigned_bridge_resources() type
mask.
Fixes: 5b28541552ef ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
|
|
Increase the maximum BAR size from 8GB to 128GB.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Merge quoted strings that are broken across lines into a single entity.
The compiler merges them anyway, but checkpatch complains about it, and
merging them makes it easier to grep for strings.
No functional change.
[bhelgaas: changelog, do the same for everything under drivers/pci]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Fix various whitespace errors.
No functional change.
[bhelgaas: fix other similar problems]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
into next
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
Conflicts:
drivers/pci/pci-sysfs.c
|
|
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c9423 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
'pci/resource' into next
* dma-api:
iommu/exynos: Remove unnecessary "&" from function pointers
DMA-API: Update dma_pool_create ()and dma_pool_alloc() descriptions
DMA-API: Fix duplicated word in DMA-API-HOWTO.txt
DMA-API: Capitalize "CPU" consistently
sh/PCI: Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
DMA-API: Change dma_declare_coherent_memory() CPU address to phys_addr_t
DMA-API: Clarify physical/bus address distinction
* pci/virtualization:
PCI: Mark RTL8110SC INTx masking as broken
* pci/msi:
PCI/MSI: Remove pci_enable_msi_block()
* pci/misc:
PCI: Remove pcibios_add_platform_entries()
s390/pci: use pdev->dev.groups for attribute creation
PCI: Move Open Firmware devspec attribute to PCI common code
* pci/resource:
PCI: Add resource allocation comments
PCI: Simplify __pci_assign_resource() coding style
PCI: Change pbus_size_mem() return values to be more conventional
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources
PCI: Support BAR sizes up to 8GB
resources: Clarify sanity check message
PCI: Don't add disabled subtractive decode bus resources
PCI: Don't print anything while decoding is disabled
PCI: Don't set BAR to zero if dma_addr_t is too small
PCI: Don't convert BAR address to resource if dma_addr_t is too small
PCI: Reject BAR above 4GB if dma_addr_t is too small
PCI: Fail safely if we can't handle BARs larger than 4GB
x86/gart: Tidy messages and add bridge device info
x86/gart: Replace printk() with pr_info()
x86/PCI: Move pcibios_assign_resources() annotation to definition
x86/PCI: Mark ATI SBx00 HPET BAR as IORESOURCE_PCI_FIXED
x86/PCI: Don't try to move IORESOURCE_PCI_FIXED resources
x86/PCI: Fix Broadcom CNB20LE unintended sign extension
|
|
Add comments in the code to match the allocation strategy of 7c671426dfc3
("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources").
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pbus_size_mem() previously returned 0 for failure and 1 for success.
Change it to return -ENOSPC for failure and 0 for success.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
This patch changes the way we handle 64-bit prefetchable bridge windows to
make it more likely that we can assign space to all devices.
Previously we put all prefetchable resources in the prefetchable bridge
window. If any of those resources was 32-bit only, we restricted the
window to be below 4GB.
After this patch, we only put 64-bit prefetchable resources in a 64-bit
prefetchable window. We put all 32-bit prefetchable resources in the
non-prefetchable window, even if there are no 64-bit prefetchable
resources.
With the previous approach, if there was a 32-bit prefetchable resource
behind a bridge, we forced the bridge's prefetchable window below 4GB,
which meant that even if there was plenty of space above 4GB available, we
couldn't use it, and assignment of large 64-bit resources could fail, as
in the bugzilla below.
The new strategy is:
1) If the prefetchable window is 64 bits wide, we put only 64-bit
prefetchable resources in it. Any 32-bit prefetchable resources go in
the non-prefetchable window.
2) If the prefetchable window is 32 bits wide, we put both 32- and 64-bit
prefetchable resources in it.
3) If there is no prefetchable window, all MMIO resources go in the
non-prefetchable window.
This reduces performance for 32-bit prefetchable resources below a bridge
with a 64-bit prefetchable window. We previously assigned prefetchable
space, but now we'll assign non-prefetchable space. This is the case even
if there are no 64-bit prefetchable resources, or if they would all fit
below 4GB. In those cases, the old strategy would work and would have
better performance.
[bhelgaas: write changelog, add bugzilla link, fold in mem64_mask removal]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=74151
Tested-by: Guo Chao <yan@linux.vnet.ibm.com>
Tested-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
This is needed for some of the Xeon Phi type systems.
[bhelgaas: added Nikhil, use ARRAY_SIZE() to connect with decl, folded in
Kevin's "order < 0" fix to ARRAY_SIZE() usage]
Signed-off-by: Nikhil P Rao <nikhil.rao@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some PCI functions used to be marked __devinit. When CONFIG_HOTPLUG was
not set, these functions were discarded after boot. A few callers of these
__devinit functions were marked __ref to indicate that they could safely
call the __devinit functions even though the callers were not __devinit.
But CONFIG_HOTPLUG and __devinit are now gone, and the need for the __ref
annotations is also gone, so remove them. Relevant historical commits:
54b956b90360 Remove __dev* markings from init.h
a8e4b9c101ae PCI: add generic pci_hp_add_bridge()
0ab2b57f8db8 PCI: fix section mismatch warning in pci_scan_child_bus
451124a7cc6c PCI: fix 4x section mismatch warnings
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
* pci/resource:
PCI: Allocate 64-bit BARs above 4G when possible
PCI: Enforce bus address limits in resource allocation
PCI: Split out bridge window override of minimum allocation address
agp/ati: Use PCI_COMMAND instead of hard-coded 4
agp/intel: Use CPU physical address, not bus address, for ioremap()
agp/intel: Use pci_bus_address() to get GTTADR bus address
agp/intel: Use pci_bus_address() to get MMADR bus address
agp/intel: Support 64-bit GMADR
agp/intel: Rename gtt_bus_addr to gtt_phys_addr
drm/i915: Rename gtt_bus_addr to gtt_phys_addr
agp: Use pci_resource_start() to get CPU physical address for BAR
agp: Support 64-bit APBASE
PCI: Add pci_bus_address() to get bus address of a BAR
PCI: Convert pcibios_resource_to_bus() to take a pci_bus, not a pci_dev
PCI: Change pci_bus_region addresses to dma_addr_t
|
|
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
Logan Gunthorpe
Bjorn Helgaas
Mohan Kumar
Nicholas Johnson
Honghui Zhang
Jon Derrick
Mika Westerberg
Frederick Lawler
Markus Elfring
Andy Shevchenko
Christian König
Yongji Xie
Rui Wang
Linus Torvalds
Lorenzo Pieralisi
Gavin Shan
Bogicevic Sasa
David Daney
Yinghai Lu
Wei Yang
Ray Jui
Ryan Desfosses
Yijing Wang
Alan