| Age | Commit message (Collapse) | Author |
|---|
|
In case we fail to enable p2pmem on the current namespace, disable the
backing store device before exiting.
Cc: Stephen Bates <sbates@raithlin.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
There are two mistakes for building bvec from sg list for file
backed ns:
- use request data length to compute number of io vector, this way
doesn't consider sg->offset, and the result may be smaller than required
io vectors
- bvec->bv_len isn't capped by sg->length
This patch fixes this issue by building bvec from sg directly, given
the whole IO stack is ready for multi-page bvec.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Fixes: 3a85a5de29ea ("nvme-loop: add a NVMe loopback host driver")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When undergoing state transitions I/O might be requeued, hence
we should always call nvme_mpath_set_live() to schedule requeue_work
whenever the nvme device is live, independent on whether the
old state was live or not.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Gargi Srinivas <sring@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
nvme_tcp_end_request just takes the status value and the converts
it to little endian as well as shifting for the phase bit.
Fixes: 43ce38a6d823 ("nvme-tcp: support C2HData with SUCCESS flag")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
|
|
A C2HData PDU with the SUCCESS flag set indicates that the I/O was
completed by the controller successfully and means that a subsequent
completion response capsule PDU will be ommitted.
If we see this flag, fisrt we check that LAST_PDU flag is set as well,
and then we complete the request when the data transfer (and data digest
verification if its on) is done.
While we're at it, reuse a bit of code with nvme_fail_request.
Reported-by: Steve Blightman <steve.blightman@oracle.com>
Suggested-by: Oliver Smith-Denny <osmithde@cisco.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Oliver Smith-Denny <osmithde@cisco.com>
Tested-by: Oliver Smith-Denny <osmithde@cisco.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
NVMe DSM is a pure hint, so if the underlying device / file system
does not support discard-like operations we should not fail the
operation but rather return success.
Fixes: 3b031d15995f ("nvmet: add error log support for bdev backend")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Tested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a gendisk argument to nvme_config_write_zeroes so that the call to
nvme_update_disk_info for the multipath device node updates the
proper request_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Tested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a gendisk argument to nvme_config_discard so that the call to
nvme_update_disk_info for the multipath device node updates the
proper request_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Tested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Just opencode the two function calls in the caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Tested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Qemu started out with a broken implementation of Write Zeroes written
by yours truly. Disable Write Zeroes on qemu for now, eventually
we need to go back and make all the qemu quirks version specific,
but that is left for another time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The FC-NVME spec, when finally approved, modified the disconnect LS
such that the only scope available is the association.
Rework the Disconnect LS processing to be in accordance with the
change.
Signed-off-by: Nigel Kirkland <nigel.kirkland@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There are two changes:
1) The logic in the __nvmet_fc_free_assoc() routine is bad. It uses
"safe" routines assuming pointers will come back valid. However, the
intervening next structure being linked can be removed from the list and
the resulting safe pointers are bad, resulting in NULL ptrs being hit.
Correct by scheduling a work element to perform the association delete,
which can be done while under lock.
2) Prior patch that added the work element scheduling left a possible
reference on the object if the work element couldn't be scheduled.
Correct by doing the put on a failing schedule_work() call.
Signed-off-by: Nigel Kirkland <nigel.kirkland@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If:
- A successful connect has occurred with an io queue count greater than
zero and namespaces detected and running.
- An error or something occurs which causes a termination of the prior
association and then starts a reconnect,
- The reconnect then creates a new controller, but for whatever reason,
nvme_set_queue_count() results in io queue count set to zero. This
will skip io queue and tag set changes.
- But... the controller will transition to live, calling
nvme_start_ctrl, which calls nvme_start_queues(), which then releases
I/Os into the transport which then sends them to the driver.
As there are no queues, things eventually hit the driver looking for a
handle, which was cleared when the original controller was reset, and it
can't proceed. Worst case, things progress, but everything fails.
In the failing scenario, the nvme_set_features(NVME_FEAT_NUM_QUEUES)
command actually failed with a NVME_SC_INTERNAL error. For some reason,
although nvme_set_queue_count() saw the error and set io queue count to
zero, it doesn't return a failure status to the transport, which allows
the transport to continue using the controller.
Fix the problem by simply rejecting the new association if at least 1
I/O queue can't be created. The association reject will fail the
reconnect attempt and fall into the reconnect retry policy.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A recent change added a numa_node field to the nvme controller
and has the transport assign the node using dev_to_node().
However, fcloop registers with a NULL device struct, so the
dev_to_node() call oops.
Revise the assignment to assign no node when device struct is null.
Fixes: 103e515efa89b ("nvme: add a numa_node field to struct nvme_ctrl")
Reported-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
[hch: small coding style fixup]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
For some nvme command, when issued by the nvme core layer, there
is an internal buffer which can cause blk_rq_payload_bytes() to
return a non-zero value yet there is no actual/real command payload
and sg list. An example is the WRITE ZEROES command.
To address this, when making choices on whether to dma map an sgl,
use blk_rq_nr_phys_segments() instead of blk_rq_payload_bytes().
When there is a sgl, blk_rq_payload_bytes() will return the amount
of data to be transferred by the sgl.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
After commit 4d43d395fe (workqueue: Try to catch flush_work() without
INIT_WORK()), it can cause warning when delete nvme-loop device, trace
like:
[ 76.601272] Call Trace:
[ 76.601646] ? del_timer+0x72/0xa0
[ 76.602156] __cancel_work_timer+0x1ae/0x270
[ 76.602791] cancel_work_sync+0x14/0x20
[ 76.603407] nvmet_ctrl_free+0x1b7/0x2f0 [nvmet]
[ 76.604091] ? free_percpu+0x168/0x300
[ 76.604652] nvmet_sq_destroy+0x106/0x240 [nvmet]
[ 76.605346] nvme_loop_destroy_admin_queue+0x30/0x60 [nvme_loop]
[ 76.606220] nvme_loop_shutdown_ctrl+0xc3/0xf0 [nvme_loop]
[ 76.607026] nvme_loop_delete_ctrl_host+0x19/0x30 [nvme_loop]
[ 76.607871] nvme_do_delete_ctrl+0x75/0xb0
[ 76.608477] nvme_sysfs_delete+0x7d/0xc0
[ 76.609057] dev_attr_store+0x24/0x40
[ 76.609603] sysfs_kf_write+0x4c/0x60
[ 76.610144] kernfs_fop_write+0x19a/0x260
[ 76.610742] __vfs_write+0x1c/0x60
[ 76.611246] vfs_write+0xfa/0x280
[ 76.611739] ksys_write+0x6e/0x120
[ 76.612238] __x64_sys_write+0x1e/0x30
[ 76.612787] do_syscall_64+0xbf/0x3a0
[ 76.613329] entry_SYSCALL_64_after_hwframe+0x44/0xa9
We fix it by moving fatal_err_work init to nvmet_alloc_ctrl(), which may
more reasonable.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
After commit a686ed75c0fb ("nvme: introduce a helper function for
controller deletion), nvme_delete_ctrl_sync no longer use flush_work.
Update comment, accordingly.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In case nvme_alloc_ns fails after we initialize ns_head but before we
add the ns to the controller namespaces list we need to explicitly put
the ns_head reference because when we teardown the controller we
won't find it, causing us to leak a dangling subsystem eventually.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The field is defined to be a 24 byte array, we don't need to multiply
the sizeof() that field by the number of dwords it covers.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A write or flush IO passthrough command is expected to change the
logical block content, so don't warn on these as no additional handling
is necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This will print get-feature cmd in more informative way. For example,
run "nvme get-feature /dev/nvme0 -n 1 -f 0x9 -c 10" will trace:
nvme-3907 [008] .... 1763.635054: nvme_setup_cmd: nvme0: qid=0, cmdid=6, nsid=1, flags=0x0, meta=0x0, cmd=(nvme_admin_get_features fid=0x9 sel=0x0 cdw11=0xa)
<idle>-0 [001] d.h. 1763.635112: nvme_sq: nvme0: qid=0, head=27, tail=27
<idle>-0 [008] ..s. 1763.635121: nvme_complete_rq: nvme0: qid=0, cmdid=6, res=10, retries=0, flags=0x2, status=0
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The interrupt departement delivers this time:
- New infrastructure to manage NMIs on platforms which have a sane
NMI delivery, i.e. identifiable NMI vectors instead of a single
lump.
- Simplification of the interrupt affinity management so drivers
don't have to implement ugly loops around the PCI/MSI enablement.
- Speedup for interrupt statistics in /proc/stat
- Provide a function to retrieve the default irq domain
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- The usual small fixes, improvements and cleanups all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
irqchip/imx-irqsteer: Add multi output interrupts support
irqchip/imx-irqsteer: Change to use reg_num instead of irq_group
dt-bindings: irq: imx-irqsteer: Add multi output interrupts support
dt-binding: irq: imx-irqsteer: Use irq number instead of group number
irqchip/brcmstb-l2: Use _irqsave locking variants in non-interrupt code
irqchip/gicv3-its: Use NUMA aware memory allocation for ITS tables
irqdomain: Allow the default irq domain to be retrieved
irqchip/sifive-plic: Implement irq_set_affinity() for SMP host
irqchip/sifive-plic: Differentiate between PLIC handler and context
irqchip/sifive-plic: Add warning in plic_init() if handler already present
irqchip/sifive-plic: Pre-compute context hart base and enable base
PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
genirq/affinity: Remove the leftovers of the original set support
nvme-pci: Simplify interrupt allocation
genirq/affinity: Add new callback for (re)calculating interrupt sets
genirq/affinity: Store interrupt sets size in struct irq_affinity
genirq/affinity: Code consolidation
irqchip/irq-sifive-plic: Check and continue in case of an invalid cpuid.
irqchip/i8259: Fix shutdown order by moving syscore_ops registration
dt-bindings: interrupt-controller: loongson ls1x intc
...
|
|
Use blk_rq_nr_phys_segments() instead of blk_rq_payload_bytes() to check
if a command contains data to be mapped. This fixes the case where
a struct request contains LBAs, but it has no payload, such as
Write Zeroes support.
Fixes: 6e02318eaea5 ("nvme: add support for the Write Zeroes command")
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
nvme_alloc_ns() might fail, so we should be returning an error code.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Rework nvme_delete_ctrl_sync() such that it does not have to wait for
queued work. This patch avoids that test nvme/008 triggers the following
complaint:
WARNING: possible circular locking dependency detected
5.0.0-rc6-dbg+ #10 Not tainted
------------------------------------------------------
nvme/7918 is trying to acquire lock:
000000009a1a7b69 ((work_completion)(&ctrl->delete_work)){+.+.}, at: __flush_work+0x379/0x410
but task is already holding lock:
00000000ef5a45b4 (kn->count#389){++++}, at: kernfs_remove_self+0x196/0x210
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (kn->count#389){++++}:
lock_acquire+0xc5/0x1e0
__kernfs_remove+0x42a/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x68/0xb0
device_del+0x24d/0x570
cdev_device_del+0x1a/0x50
nvme_delete_ctrl_work+0xbd/0xe0
process_one_work+0x4f1/0xa40
worker_thread+0x67/0x5b0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
-> #0 ((work_completion)(&ctrl->delete_work)){+.+.}:
__lock_acquire+0x1323/0x17b0
lock_acquire+0xc5/0x1e0
__flush_work+0x399/0x410
flush_work+0x10/0x20
nvme_delete_ctrl_sync+0x65/0x70
nvme_sysfs_delete+0x4f/0x60
dev_attr_store+0x3e/0x50
sysfs_kf_write+0x87/0xa0
kernfs_fop_write+0x186/0x240
__vfs_write+0xd7/0x430
vfs_write+0xfa/0x260
ksys_write+0xab/0x130
__x64_sys_write+0x43/0x50
do_syscall_64+0x71/0x210
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(kn->count#389);
lock((work_completion)(&ctrl->delete_work));
lock(kn->count#389);
lock((work_completion)(&ctrl->delete_work));
*** DEADLOCK ***
3 locks held by nvme/7918:
#0: 00000000e2223b44 (sb_writers#6){.+.+}, at: vfs_write+0x1eb/0x260
#1: 000000003404976f (&of->mutex){+.+.}, at: kernfs_fop_write+0x128/0x240
#2: 00000000ef5a45b4 (kn->count#389){++++}, at: kernfs_remove_self+0x196/0x210
stack backtrace:
CPU: 4 PID: 7918 Comm: nvme Not tainted 5.0.0-rc6-dbg+ #10
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
dump_stack+0x86/0xca
print_circular_bug.isra.36.cold.54+0x173/0x1d5
check_prev_add.constprop.45+0x996/0x1110
__lock_acquire+0x1323/0x17b0
lock_acquire+0xc5/0x1e0
__flush_work+0x399/0x410
flush_work+0x10/0x20
nvme_delete_ctrl_sync+0x65/0x70
nvme_sysfs_delete+0x4f/0x60
dev_attr_store+0x3e/0x50
sysfs_kf_write+0x87/0xa0
kernfs_fop_write+0x186/0x240
__vfs_write+0xd7/0x430
vfs_write+0xfa/0x260
ksys_write+0xab/0x130
__x64_sys_write+0x43/0x50
do_syscall_64+0x71/0x210
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch does not change any functionality but makes the next patch
in this series easier to read.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Since nvme_delete_ctrl_sync() is not called from any other kernel module,
unexport it.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch avoids that the compiler complains about 'ret' being set
but not being used when building with W=1.
Fixes: 3b6592f70ad7 ("nvme: utilize two queue maps, one for reads and one for writes") # v5.0-rc1
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch avoids that the kernel-doc tool reports a warning when
building with W=1.
Fixes: 26c682274e0a ("nvme-fabrics: allow nvmf_connect_io_queue to poll") # v5.0-rc1
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch avoids that smatch complains about inconsistent indentation.
Fixes: a07b4970f464 ("nvmet: add a generic NVMe target") # v4.10
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Implement a simple round-robin I/O policy for multipathing. Path
selection is done in two rounds, first iterating across all optimized
paths, and if that doesn't return any valid paths, iterate over all
optimized and non-optimized paths. If no paths are found, use the
existing algorithm. Also add a sysfs attribute 'iopolicy' to switch
between the current NUMA-aware I/O policy and the 'round-robin' I/O
policy.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The NVME PCI driver contains a tedious mechanism for interrupt
allocation, which is necessary to adjust the number and size of interrupt
sets to the maximum available number of interrupts which depends on the
underlying PCI capabilities and the available CPU resources.
It works around the former short comings of the PCI and core interrupt
allocation mechanims in combination with interrupt sets.
The PCI interrupt allocation function allows to provide a maximum and a
minimum number of interrupts to be allocated and tries to allocate as
many as possible. This worked without driver interaction as long as there
was only a single set of interrupts to handle.
With the addition of support for multiple interrupt sets in the generic
affinity spreading logic, which is invoked from the PCI interrupt
allocation, the adaptive loop in the PCI interrupt allocation did not
work for multiple interrupt sets. The reason is that depending on the
total number of interrupts which the PCI allocation adaptive loop tries
to allocate in each step, the number and the size of the interrupt sets
need to be adapted as well. Due to the way the interrupt sets support was
implemented there was no way for the PCI interrupt allocation code or the
core affinity spreading mechanism to invoke a driver specific function
for adapting the interrupt sets configuration.
As a consequence the driver had to implement another adaptive loop around
the PCI interrupt allocation function and calling that with maximum and
minimum interrupts set to the same value. This ensured that the
allocation either succeeded or immediately failed without any attempt to
adjust the number of interrupts in the PCI code.
The core code now allows drivers to provide a callback to recalculate the
number and the size of interrupt sets during PCI interrupt allocation,
which in turn allows the PCI interrupt allocation function to be called
in the same way as with a single set of interrupts. The PCI code handles
the adaptive loop and the interrupt affinity spreading mechanism invokes
the driver callback to adapt the interrupt set configuration to the
current loop value. This replaces the adaptive loop in the driver
completely.
Implement the NVME specific callback which adjusts the interrupt sets
configuration and remove the adaptive allocation loop.
[ tglx: Simplify the callback further and restore the dropped adjustment of
number of sets ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.602546658@linutronix.de
|
|
The interrupt affinity spreading mechanism supports to spread out
affinities for one or more interrupt sets. A interrupt set contains one
or more interrupts. Each set is mapped to a specific functionality of a
device, e.g. general I/O queues and read I/O queus of multiqueue block
devices.
The number of interrupts per set is defined by the driver. It depends on
the total number of available interrupts for the device, which is
determined by the PCI capabilites and the availability of underlying CPU
resources, and the number of queues which the device provides and the
driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via
a pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a
loop in the driver to determine the maximum number of interrupts which
are provided by the PCI capabilities and the underlying CPU resources.
This loop would have to be replicated in every driver which wants to
utilize this mechanism. That's unwanted code duplication and error
prone.
In order to move this into generic facilities it is required to have a
mechanism, which allows the recalculation of the interrupt sets and
their size, in the core code. As the core code does not have any
knowledge about the underlying device, a driver specific callback will
be added to struct affinity_desc, which will be invoked by the core
code. The callback will get the number of available interupts as an
argument, so the driver can calculate the corresponding number and size
of interrupt sets.
To support this, two modifications for the handling of struct irq_affinity
are required:
1) The (optional) interrupt sets size information is contained in a
separate array of integers and struct irq_affinity contains a
pointer to it.
This is cumbersome and as the maximum number of interrupt sets is small,
there is no reason to have separate storage. Moving the size array into
struct affinity_desc avoids indirections and makes the code simpler.
2) At the moment the struct irq_affinity pointer which is handed in from
the driver and passed through to several core functions is marked
'const'.
With the upcoming callback to recalculate the number and size of
interrupt sets, it's necessary to remove the 'const'
qualifier. Otherwise the callback would not be able to update the data.
Implement #1 and store the interrupt sets size in 'struct irq_affinity'.
No functional change.
[ tglx: Fixed the memcpy() size so it won't copy beyond the size of the
source. Fixed the kernel doc comments for struct irq_affinity and
de-'This patch'-ed the changelog ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.423723127@linutronix.de
|
|
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
|
|
The reset work holds a mutex to prevent races with removal modifying the
same resources, but was unlocking only on success. Unlock on failure
too.
Fixes: 5c959d73dba64 ("nvme-pci: fix rapid add remove sequence")
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
A surprise removal may fail to tear down request queues if it is racing
with the initial asynchronous probe. If that happens, the remove path
won't see the queue resources to tear down, and the controller reset
path may create a new request queue on a removed device, but will not
be able to make forward progress, deadlocking the pci removal.
Protect setting up non-blocking resources from a shutdown by holding the
same mutex, and transition to the CONNECTING state after these resources
are initialized so the probe path may see the dead controller state
before dispatching new IO.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202081
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If a controller supports the NS Change Notification, the namespace
scan_work is automatically triggered after attaching a new namespace.
Occasionally the namespace scan_work may append the new namespace to the
list before the admin command effects handling is completed. The effects
handling unfreezes namespaces, but if it unfreezes the newly attached
namespace, its request_queue freeze depth will be off and we'll hit the
warning in blk_mq_unfreeze_queue().
On the next namespace add, we will fail to freeze that queue due to the
previous bad accounting and deadlock waiting for frozen.
Fix that by preventing scan work from altering the namespace list while
command effects handling needs to pair freeze with unfreeze.
Reported-by: Wen Xiong <wenxiong@us.ibm.com>
Tested-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
Max Gurtovoy
Ming Lei
Martin George
Christoph Hellwig
Linus Torvalds
Sagi Grimberg
James Smart
Yufen Yu
Keith Busch
Chaitanya Kulkarni
Hannes Reinecke
Bart Van Assche
Jens Axboe