| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit e47488b2df7f9cb405789c7f5d4c27909fc597ae ]
According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf129856 ("phy: Add file missed in previous commit.")
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 63b2ed4e10b2e6c913e1d8cdd728e7fba4115a3d ]
Regarding to IEEE 802.3-2015 standard section 2
28B.3 Priority resolution - Table 28-3 - Pause resolution
In case of Local device Pause=1 AsymDir=0, Link partner
Pause=1 AsymDir=1, Local device resolution should be enable PAUSE
transmit, disable PAUSE receive.
And in case of Local device Pause=1 AsymDir=1, Link partner
Pause=1 AsymDir=0, Local device resolution should be enable PAUSE
receive, disable PAUSE transmit.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reported-by: Shaul Ben-Mayor <shaulb@marvell.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8aace4f3eba2a3ceb431e18683ea0e1ecbade5cd ]
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2158e856f56bb762ef90f3ec244d41a519826f75 ]
sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8a17eefa235f73b60c0ca7d397d2e4f66f85f413 upstream.
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 820ee17b8d3b ("net: phy: broadcom: Add support code for reading PHY counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2b892649254fec01678c64f16427622b41fa27f4 ]
PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.
Fixes: 2a10154abcb75 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28e74a7cfd6403f0d1c0f8b10b45d6fae37b227e ]
Some SFP modules do not like reads longer than 16 bytes, so read the
EEPROM in chunks of 16 bytes at a time. This behaviour is not specified
in the SFP MSAs, which specifies:
"The serial interface uses the 2-wire serial CMOS E2PROM protocol
defined for the ATMEL AT24C01A/02/04 family of components."
and
"As long as the SFP+ receives an acknowledge, it shall serially clock
out sequential data words. The sequence is terminated when the host
responds with a NACK and a STOP instead of an acknowledge."
We must avoid breaking a read across a 16-bit quantity in the diagnostic
page, thankfully all 16-bit quantities in that page are naturally
aligned.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3d3ced2ec5d71b99d72ae6910fbdf890bc2eccf0 ]
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2f23a2a768bee7ad2ff1e9527c3f7e279e794a46 ]
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fdfdf86720a34527f777cbe0d8599bf0528fa146 ]
marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.
marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.
Fixes: 2170fef78a40 ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit c4ba68b8691e4 backported from upstream to 4.14 stable was
probably applied wrongly, and instead of calling sfp_register_socket in
sfp_probe, the socket registering code was put into sfp_remove. This is
obviously wrong.
The commit first appeared in 4.14.104. Fix it for the next 4.14 release.
Fixes: c4ba68b8691e4 ("net: sfp: do not probe SFP module before we're attached")
Cc: stable <stable@vger.kernel.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ff7b060535e87c2ae14dd8548512abfdda528fb ]
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
fixed_mdio_bus_init+0x283/0x1000 [fixed_phy]
? 0xffffffffc0e40000
? 0xffffffffc0e40000
? 0xffffffffc0e40000
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
Allocated by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
kmalloc include/linux/slab.h:545 [inline]
kzalloc include/linux/slab.h:740 [inline]
mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143
fixed_mdio_bus_init+0x163/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 3524:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kfree+0xe1/0x270 mm/slub.c:3938
device_release+0x78/0x200 drivers/base/core.c:919
kobject_cleanup lib/kobject.c:662 [inline]
kobject_release lib/kobject.c:691 [inline]
kref_put include/linux/kref.h:67 [inline]
kobject_put+0x146/0x240 lib/kobject.c:708
put_device+0x1c/0x30 drivers/base/core.c:2060
__mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382
fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8881dc824c80
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 248 bytes inside of
2048-byte region [ffff8881dc824c80, ffff8881dc825480)
The buggy address belongs to the page:
page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0
flags: 0x2fffc0000010200(slab|head)
raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800
raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 232ba3a51cc224b339c7114888ed7f0d4d95695e ]
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d25ed413d5e51644e18f66e34eec049f17a7abcb ]
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 87454b6edc1b0143fdb3d9853285477e95af74a4 upstream.
During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.
This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().
Fixes: b5bfc21af5cb ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b5bfc21af5cb3d53f9cee0ef82eaa43762a90f81 ]
When we probe a SFP module, we expect to be able to call the upstream
device's module_insert() function so that the upstream link can be
configured. However, when the upstream device is delayed, we currently
may end up probing the module before the upstream device is available,
and lose the module_insert() call.
Avoid this by holding off probing the module until the SFP bus is
properly connected to both the SFP socket driver and the upstream
driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 197f9ab7f08ce4b9ece662f747c3991b2f0fbb57 ]
Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.
With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Fixes: f411a6160bd4 ("net: phy: Add gmiitorgmii converter support")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 53bc8d2af08654659abfadfd3e98eb9922ff787c ]
During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.
Purge old skbs in decode_txts().
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
handling
[ Upstream commit e40e2a2e78664fa90ea4b9bdf4a84efce2fea9d9 ]
The current code in __mdiobus_register() doesn't properly handle
failures returned by the devm_gpiod_get_optional() call: it returns
immediately, without unregistering the device that was added by the
call to device_register() earlier in the function.
This leaves a stale device, which then causes a NULL pointer
dereference in the code that handles deferred probing:
[ 1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074
[ 1.498110] pgd = (ptrval)
[ 1.500838] [00000074] *pgd=00000000
[ 1.504432] Internal error: Oops: 17 [#1] SMP ARM
[ 1.509133] Modules linked in:
[ 1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99
[ 1.520708] Hardware name: Xilinx Zynq Platform
[ 1.525261] Workqueue: events deferred_probe_work_func
[ 1.530403] PC is at klist_next+0x10/0xfc
[ 1.534403] LR is at device_for_each_child+0x40/0x94
[ 1.539361] pc : [<c0683fbc>] lr : [<c0455d90>] psr: 200e0013
[ 1.545628] sp : ceeefe68 ip : 00000001 fp : ffffe000
[ 1.550863] r10: 00000000 r9 : c0c66790 r8 : 00000000
[ 1.556079] r7 : c0457d44 r6 : 00000000 r5 : ceeefe8c r4 : cfa2ec78
[ 1.562604] r3 : 00000064 r2 : c0457d44 r1 : ceeefe8c r0 : 00000064
[ 1.569129] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 1.576263] Control: 18c5387d Table: 0ed7804a DAC: 00000051
[ 1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval))
[ 1.588280] Stack: (0xceeefe68 to 0xceef0000)
[ 1.592630] fe60: cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790
[ 1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78
[ 1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac
[ 1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10
[ 1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c
[ 1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c
[ 1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00
[ 1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000
[ 1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4
[ 1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000
[ 1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
[ 1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94)
[ 1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[ 1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94)
[ 1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[ 1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40)
[ 1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c)
[ 1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc)
[ 1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0)
[ 1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154)
[ 1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[ 1.785689] Exception stack(0xceeeffb0 to 0xceeefff8)
[ 1.790739] ffa0: 00000000 00000000 00000000 00000000
[ 1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010)
[ 1.819844] ---[ end trace 3c2c0c8b65399ec9 ]---
The actual error that we had from devm_gpiod_get_optional() was
-EPROBE_DEFER, due to the GPIO being provided by a driver that is
probed later than the Ethernet controller driver.
To fix this, we simply add the missing device_del() invocation in the
error path.
Fixes: 69226896ad636 ("mdio_bus: Issue GPIO RESET to PHYs")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8742beb50f2db903d3b6d69ddd81d67ce9914453 ]
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d2a36971ef595069b7a600d1144c2e0881a930a1 ]
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df5a8ec64eed7fe45b556cfff503acd6429ab817 ]
Up until commit 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aeeb2e8fdefdd5d257a1446351c70cb3df540199 ]
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3bcd47726c3b744fd08781795cca905cc59a1382 ]
If CONFIG_GPIOLIB is disabled, gpiod_put() becomes a stub that produces a
warning, this helped identify that we could be attempting to release a NULL
pl->link_gpio GPIO descriptor, so guard against that.
Fixes: daab3349ad1a ("net: phy: phylink: Release link GPIO")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5df7af85ecd88e8b5f1f31d6456c3cf38a8bbdda ]
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0231b1a074c672f8c00da00a57144072890d816b ]
The Ethernet on mpc8315erdb is broken since commit b6b5e8a69118
("gianfar: Disable EEE autoneg by default"). The reason is that
even though the rtl8211b doesn't support the MMD extended registers
access, it does return some random values if we trying to access
the MMD register via indirect method. This makes it seem that the
EEE is supported by this phy device. And the subsequent writing to
the MMD registers does cause the phy malfunction. So use the dummy
stubs for the MMD register access to fix this issue.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab4e6ee578e88a659938db8fbf33720bc048d29c ]
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002 f5d1f03c f5d1f05c f5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8d0752d11312be830c33e84dfd1016e6a47c2938 ]
We're ignoring the result of the attached phy device's read_status().
Return it so we can detect errors.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 77fefa93bfebe4df44f154f2aa5938e32630d0bf ]
Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b0753408aadf32c7ece9e6b765017881e54af833 ]
mdio_mux_iproc_probe() uses platform_set_drvdata() to store md pointer
in device, whereas mdio_mux_iproc_remove() restores md pointer by
dev_get_platdata(&pdev->dev). This leads to wrong resources release.
The patch replaces getter to platform_get_drvdata.
Fixes: 98bc865a1ec8 ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit daab3349ad1a69663ccad278ed71d55974d104b4 ]
We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 215d08a85b9acf5e1fe9dbf50f1774cde333efef ]
The situation described in the comment can occur also with
PHY_IGNORE_INTERRUPT, therefore change the condition to include it.
Fixes: f555f34fdc58 ("net: phy: fix auto-negotiation stall due to unavailable interrupt")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df8ed346d4a806a6eef2db5924285e839604b3f9 ]
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b6a930fa88083b41d26ddf1cab95cbd740936c22 ]
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 733a969a7ed14fc5786bcc59c1bdda83c7ddb46e ]
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).
This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.
Fixes: 5b4e29005123 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 79fb218d97980d4fee9a64f4c8ff05289364ba25 ]
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 76327a35caabd1a932e83d6a42b967aa08584e5d ]
The datasheet specifies a 3uS pause after performing a software
reset. The default implementation of genphy_soft_reset() does not
provide this, so implement soft_reset with the needed pause.
Signed-off-by: Esben Haabendal <eha@deif.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a2c054a896b8ac794ddcfc7c92e2dc7ec4ed4ed5 ]
In 664fcf123a30e (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.
With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4414b3ed74be0e205e04e12cd83542a727d88255 ]
Some ethernet drivers (like TI CPSW) may connect and manage >1 Net PHYs per
one netdevice, as result such drivers will produce warning during system
boot and fail to connect second phy to netdevice when PHYLIB framework
will try to create sysfs link netdev->phydev for second PHY
in phy_attach_direct(), because sysfs link with the same name has been
created already for the first PHY. As result, second CPSW external
port will became unusable.
Fix it by relaxing error checking when PHYLIB framework is creating sysfs
link netdev->phydev in phy_attach_direct(), suppressing warning by using
sysfs_create_link_nowarn() and adding error message instead.
After this change links (phy->netdev and netdev->phy) creation failure is not
fatal any more and system can continue working, which fixes TI CPSW issue.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes: a3995460491d ("net: phy: Relax error checking on sysfs_create_link()")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 20b56ed9f8adfb9a7fb1c878878c54aa4ed645c1 ]
The detection of a PHY changed in commit e98a3aabf85f ("mdio_bus: don't
return NULL from mdiobus_scan()") which now causes sfp to print an
error message. Update for this change.
Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2794ffc441dde3109804085dc745e8014a4de224 ]
The EEPROM reading was trying to read from the second EEPROM address
if we requested the last byte from the SFF8079 EEPROM, which caused a
failure when the second EEPROM is not present. Discovered with a
S-RJ01 SFP module. Fix this.
Fixes: 73970055450e ("sfp: add SFP module support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9042b46eda33ef5db3cdfc9e12b3c8cabb196141 ]
Always check phy_write return values. Better to be safe than sorry
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c2c2e62df3fa30fb13fbeb7512a4eede729383b upstream.
commit f5e64032a799 ("net: phy: fix resume handling") changes the
locking semantics for phy_resume() such that the caller now needs to
hold the phy mutex. Not all call sites were adopted to this new
semantic, resulting in warnings from the added
WARN_ON(!mutex_is_locked(&phydev->lock)). Rather than change the
semantics, add a __phy_resume() and restore the old behavior of
phy_resume().
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: f5e64032a799 ("net: phy: fix resume handling")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f5e64032a799d4f54decc7eb6aafcdffb67f9ad9 ]
When a PHY has the BMCR_PDOWN bit set, it may decide to ignore writes
to other registers, or reset the registers to power-on defaults.
Micrel PHYs do this for their interrupt registers.
The current structure of phylib tries to enable interrupts before
resuming (and releasing) the BMCR_PDOWN bit. This fails, causing
Micrel PHYs to stop working after a suspend/resume sequence if they
are using interrupts.
Fix this by ensuring that the PHY driver resume methods do not take
the phydev->lock mutex themselves, but the callers of phy_resume()
take that lock. This then allows us to move the call to phy_resume()
before we enable interrupts in phy_start().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 08f5138512180a479ce6b9d23b825c9f4cd3be77 ]
This condition wasn't adjusted when PHY_IGNORE_INTERRUPT (-2) was added
long ago. In case of PHY_IGNORE_INTERRUPT the MAC interrupt indicates
also PHY state changes and we should do what the symbol says.
Fixes: 84a527a41f38 ("net: phylib: fix interrupts re-enablement in phy_start")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 56c0290202ab94a2f2780c449395d4ae8495fab4 ]
If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9feb ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ab14436065c8066c265540312742390d6d07ddd2 ]
There are several error paths in xgene_mdio_probe(),
where clk is left undisabled. The patch fixes them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2012b7d6b2868c532f22d9172c8b24611637eb48 ]
Ensure that we tell the MAC to take the link down when phylink_stop()
is called, and that this completes prior to phylink_stop() returns.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit acf1c02f023926b8b04672a9e81b1711ae681619 ]
The options word is a be16 quantity, so we need to test the flags
having converted the endian-ness. Convert the flag bits to be16,
which can be optimised by the compiler, rather than converting a
variable at runtime.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Peter Mamonov
Stefan Chulski
René van Dorst
Robert Hancock
Ioana Ciornei
Florian Fainelli
Max Uvarov
Russell King
Daniel Gomez
Andrew Lunn
Marek Behún
YueHaibing
Rajasingh Thavamani
Heiner Kallweit
Paul Kocialkowski
Sebastian Andrzej Siewior
Thomas Petazzoni
Kunihiko Hayashi
Martin Schiller
Antoine Tenart
Kevin Hao
Brandon Maier
Arun Parameswaran
Anton Vasilyev
Jingju Hou
Esben Haabendal
Brad Mouring
Grygorii Strashko
Jerome Brunet
Christophe JAILLET
Alexey Khoroshilov