| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
|
|
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Reported-by: Baptiste Covolato <baptiste@arista.com>
Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix an issue where the driver wrongly detected ipv6 neighbour updates
from the NFP as corrupt. Add a reserved field on the kernel side so
it is similar to the ipv4 version of the struct and has space for the
extra bytes from the card.
Fixes: 9ea9bfa12240 ("nfp: flower: support ipv6 tunnel keep-alive messages from fw")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VALIDATE_MASK(eth_mask->h_source) is checked twice in a row in
bcmgenet_validate_flow(). Add VALIDATE_MASK(eth_mask->h_dest)
instead.
Fixes: 3e370952287c ("net: bcmgenet: add support for ethtool rxnfc flows")
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for a new port mode that is a backplane connection without
support for auto negotiation.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
In RMII link mode it's required to set bit 15 IFCTL_A in MAC_SL MAC_CONTROL
register to enable support for 100Mbit link speed.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When multiple adapters are present in the system, pci hot-removing second
adapter leads to the following warning as both the adapters registered
thermal zone device with same thermal zone name/type.
Therefore, use unique thermal zone name during thermal zone device
initialization. Also mark thermal zone dev NULL once unregistered.
[ 414.370143] ------------[ cut here ]------------
[ 414.370944] sysfs group 'power' not found for kobject 'hwmon0'
[ 414.371747] WARNING: CPU: 9 PID: 2661 at fs/sysfs/group.c:281
sysfs_remove_group+0x76/0x80
[ 414.382550] CPU: 9 PID: 2661 Comm: bash Not tainted 5.8.0-rc6+ #33
[ 414.383593] Hardware name: Supermicro X10SRA-F/X10SRA-F, BIOS 2.0a 06/23/2016
[ 414.384669] RIP: 0010:sysfs_remove_group+0x76/0x80
[ 414.385738] Code: 48 89 df 5b 5d 41 5c e9 d8 b5 ff ff 48 89 df e8 60 b0 ff ff
eb cb 49 8b 14 24 48 8b 75 00 48 c7 c7 90 ae 13 bb e8 6a 27 d0 ff <0f> 0b 5b 5d
41 5c c3 0f 1f 00 0f 1f 44 00 00 48 85 f6 74 31 41 54
[ 414.388404] RSP: 0018:ffffa22bc080fcb0 EFLAGS: 00010286
[ 414.389638] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 414.390829] RDX: 0000000000000001 RSI: ffff8ee2de3e9510 RDI: ffff8ee2de3e9510
[ 414.392064] RBP: ffffffffbaef2ee0 R08: 0000000000000000 R09: 0000000000000000
[ 414.393224] R10: 0000000000000000 R11: 000000002b30006c R12: ffff8ee260720008
[ 414.394388] R13: ffff8ee25e0a40e8 R14: ffffa22bc080ff08 R15: ffff8ee2c3be5020
[ 414.395661] FS: 00007fd2a7171740(0000) GS:ffff8ee2de200000(0000)
knlGS:0000000000000000
[ 414.396825] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 414.398011] CR2: 00007f178ffe5020 CR3: 000000084c5cc003 CR4: 00000000003606e0
[ 414.399172] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 414.400352] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 414.401473] Call Trace:
[ 414.402685] device_del+0x89/0x400
[ 414.403819] device_unregister+0x16/0x60
[ 414.405024] hwmon_device_unregister+0x44/0xa0
[ 414.406112] thermal_remove_hwmon_sysfs+0x196/0x200
[ 414.407256] thermal_zone_device_unregister+0x1b5/0x1f0
[ 414.408415] cxgb4_thermal_remove+0x3c/0x4f [cxgb4]
[ 414.409668] remove_one+0x212/0x290 [cxgb4]
[ 414.410875] pci_device_remove+0x36/0xb0
[ 414.412004] device_release_driver_internal+0xe2/0x1c0
[ 414.413276] pci_stop_bus_device+0x64/0x90
[ 414.414433] pci_stop_and_remove_bus_device_locked+0x16/0x30
[ 414.415609] remove_store+0x75/0x90
[ 414.416790] kernfs_fop_write+0x114/0x1b0
[ 414.417930] vfs_write+0xcf/0x210
[ 414.419059] ksys_write+0xa7/0xe0
[ 414.420120] do_syscall_64+0x4c/0xa0
[ 414.421278] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 414.422335] RIP: 0033:0x7fd2a686afd0
[ 414.423396] Code: Bad RIP value.
[ 414.424549] RSP: 002b:00007fffc1446148 EFLAGS: 00000246 ORIG_RAX:
0000000000000001
[ 414.425638] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd2a686afd0
[ 414.426830] RDX: 0000000000000002 RSI: 00007fd2a7196000 RDI: 0000000000000001
[ 414.427927] RBP: 00007fd2a7196000 R08: 000000000000000a R09: 00007fd2a7171740
[ 414.428923] R10: 00007fd2a7171740 R11: 0000000000000246 R12: 00007fd2a6b43400
[ 414.430082] R13: 0000000000000002 R14: 0000000000000001 R15: 0000000000000000
[ 414.431027] irq event stamp: 76300
[ 414.435678] ---[ end trace 13865acb4d5ab00f ]---
Fixes: b18719157762 ("cxgb4: Add thermal zone support")
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take the tx accounting out of the work_done calculation to
prevent a possible duplicate napi_schedule call when under
high Tx stress but low Rx traffic.
Fixes: b14e4e95f9ec ("ionic: tx separate servicing")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a bunch of issues in cpsw_ndo_vlan_rx_kill_vid()
- pm_runtime_get_sync() returns non zero value. This results in
non zero value return to caller which will be interpreted as error.
So overwrite ret with zero.
- If VID matches with port VLAN VID, then set error code.
- Currently when VLAN interface is deleted, all of the VLAN mc addresses
are removed from ALE table, however the return values from ale function
calls are not checked. These functions can return error code -ENOENT.
But that shouldn't happen in a normal case. So add error print to
catch the situations so that these can be investigated and addressed.
return zero in these cases as these are not real error case, but only
serve to catch ALE table update related issues and help address the
same in the driver.
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Netpoll can try to poll napi as soon as napi_enable() is called.
It crashes trying to access a doorbell which is still NULL:
BUG: kernel NULL pointer dereference, address: 0000000000000000
CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S 5.9.0-rc1-00469-g5fd99b5d9950-dirty #26
RIP: 0010:bnxt_poll+0x121/0x1c0
Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02
41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a
netpoll_poll_dev+0xbd/0x1a0
__netpoll_send_skb+0x1b2/0x210
netpoll_send_udp+0x2c9/0x406
write_ext_msg+0x1d7/0x1f0
console_unlock+0x23c/0x520
vprintk_emit+0xe0/0x1d0
printk+0x58/0x6f
x86_vector_activate.cold+0xf/0x46
__irq_domain_activate_irq+0x50/0x80
__irq_domain_activate_irq+0x32/0x80
__irq_domain_activate_irq+0x32/0x80
irq_domain_activate_irq+0x25/0x40
__setup_irq+0x2d2/0x700
request_threaded_irq+0xfb/0x160
__bnxt_open_nic+0x3b1/0x750
bnxt_open_nic+0x19/0x30
ethtool_set_channels+0x1ac/0x220
dev_ethtool+0x11ba/0x2240
dev_ioctl+0x1cf/0x390
sock_do_ioctl+0x95/0x130
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when skb->encapsulation is 0, skb->ip_summed is CHECKSUM_PARTIAL
and it is udp packet, which has a dest port as the IANA assigned.
the hardware is expected to do the checksum offload, but the
hardware will not do the checksum offload when udp dest port is
6081.
This patch fixes it by doing the checksum in software.
Reported-by: Li Bing <libing@winhong.com>
Signed-off-by: Yi Li <yili@winhong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent changes to support user-defined RSS map assume that RX
rings are always reserved and the default RSS map is set after the
RX rings are successfully reserved. If the firmware spec is older
than 1.6.1, no ring reservations are required and the default RSS
map is not setup at all. In another scenario where the fw Resource
Manager is older, RX rings are not reserved and we also end up with
no valid RSS map.
Fix both issues in bnxt_need_reserve_rings(). In both scenarios
described above, we don't need to reserve RX rings so we need to
call this new function bnxt_check_rss_map_no_rmgr() to setup the
default RSS map when needed.
Without valid RSS map, the NIC won't receive packets properly.
Fixes: 1667cbf6a4eb ("bnxt_en: Add logical RSS indirection table structure.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no VF rings available during probe when the device is configured
using the Minimal-Static reservation strategy. In this case, the RSS
indirection table can only be initialized later, during bnxt_open_nic().
However, this was not happening because the rings will already have been
reserved via bnxt_init_dflt_ring_mode(), causing bnxt_need_reserve_rings()
to return false in bnxt_reserve_rings() and bypass the RSS table init.
Solve this by pushing the call to bnxt_set_dflt_rss_indir_tbl() into
__bnxt_reserve_rings(), which is common to both paths and is called
whenever ring configuration is changed. After doing this, the RSS table
init that must be called from bnxt_init_one() happens implicitly via
bnxt_set_default_rings(), necessitating doing the allocation earlier in
order to avoid a null pointer dereference.
Fixes: bd3191b5d87d ("bnxt_en: Implement ethtool -X to set indirection table.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9bb ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled. In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count. As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only. This causes ethtool -S to
display extra counters with no counter names.
Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.
Fixes: 125592fbf467 ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd2d ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the time of do_rest, ibmvnic tries to re-initalize the tx_pools
and rx_pools to avoid re-allocating the long term buffer. However
there is a window inside do_reset that the tx_pools and
rx_pools were freed before re-initialized making it possible to deference
null pointers.
This patch fix this issue by always check the tx_pool
and rx_pool are not NULL after ibmvnic_login. If so, re-allocating
the pools. This will avoid getting into calling reset_tx/rx_pools with
NULL adapter tx_pools/rx_pools pointer. Also add null pointer check in
reset_tx_pools and reset_rx_pools to safe handle NULL pointer case.
Signed-off-by: Mingming Cao <mmc@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: 15180eca569b ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
check_fcs() was returning bool as 0/1, which was a sign that the sense
of the function was unclear: false was good, which doesn't really match
a name like 'check_$thing'. So rename it to ef100_has_fcs_error(), and
use proper booleans in the return statements.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.
Fixes: 1bddd96cba03d ("net: arc_emac: support the phy reset for emac driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8eb6 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aaf1b ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Pull networking fixes from David Miller:
"Nothing earth shattering here, lots of small fixes (f.e. missing RCU
protection, bad ref counting, missing memset(), etc.) all over the
place:
1) Use get_file_rcu() in task_file iterator, from Yonghong Song.
2) There are two ways to set remote source MAC addresses in macvlan
driver, but only one of which validates things properly. Fix this.
From Alvin Šipraga.
3) Missing of_node_put() in gianfar probing, from Sumera
Priyadarsini.
4) Preserve device wanted feature bits across multiple netlink
ethtool requests, from Maxim Mikityanskiy.
5) Fix rcu_sched stall in task and task_file bpf iterators, from
Yonghong Song.
6) Avoid reset after device destroy in ena driver, from Shay
Agroskin.
7) Missing memset() in netlink policy export reallocation path, from
Johannes Berg.
8) Fix info leak in __smc_diag_dump(), from Peilin Ye.
9) Decapsulate ECN properly for ipv6 in ipv4 tunnels, from Mark
Tomlinson.
10) Fix number of data stream negotiation in SCTP, from David Laight.
11) Fix double free in connection tracker action module, from Alaa
Hleihel.
12) Don't allow empty NHA_GROUP attributes, from Nikolay Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
net: nexthop: don't allow empty NHA_GROUP
bpf: Fix two typos in uapi/linux/bpf.h
net: dsa: b53: check for timeout
tipc: call rcu_read_lock() in tipc_aead_encrypt_done()
net/sched: act_ct: Fix skb double-free in tcf_ct_handle_fragments() error flow
net: sctp: Fix negotiation of the number of data streams.
dt-bindings: net: renesas, ether: Improve schema validation
gre6: Fix reception with IP6_TNL_F_RCV_DSCP_COPY
hv_netvsc: Fix the queue_mapping in netvsc_vf_xmit()
hv_netvsc: Remove "unlikely" from netvsc_select_queue
bpf: selftests: global_funcs: Check err_str before strstr
bpf: xdp: Fix XDP mode when no mode flags specified
selftests/bpf: Remove test_align leftovers
tools/resolve_btfids: Fix sections with wrong alignment
net/smc: Prevent kernel-infoleak in __smc_diag_dump()
sfc: fix build warnings on 32-bit
net: phy: mscc: Fix a couple of spelling mistakes "spcified" -> "specified"
libbpf: Fix map index used in error message
net: gemini: Fix missing free_netdev() in error path of gemini_ethernet_port_probe()
net: atlantic: Use readx_poll_timeout() for large timeout
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"23 fixes in 5 drivers (qla2xxx, ufs, scsi_debug, fcoe, zfcp). The bulk
of the changes are in qla2xxx and ufs and all are mostly small and
definitely don't impact the core"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
Revert "scsi: qla2xxx: Disable T10-DIF feature with FC-NVMe during probe"
Revert "scsi: qla2xxx: Fix crash on qla2x00_mailbox_command"
scsi: qla2xxx: Fix null pointer access during disconnect from subsystem
scsi: qla2xxx: Check if FW supports MQ before enabling
scsi: qla2xxx: Fix WARN_ON in qla_nvme_register_hba
scsi: qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime
scsi: qla2xxx: Reduce noisy debug message
scsi: qla2xxx: Fix login timeout
scsi: qla2xxx: Indicate correct supported speeds for Mezz card
scsi: qla2xxx: Flush I/O on zone disable
scsi: qla2xxx: Flush all sessions on zone disable
scsi: qla2xxx: Use MBX_TOV_SECONDS for mailbox command timeout values
scsi: scsi_debug: Fix scp is NULL errors
scsi: zfcp: Fix use-after-free in request timeout handlers
scsi: ufs: No need to send Abort Task if the task in DB was cleared
scsi: ufs: Clean up completed request without interrupt notification
scsi: ufs: Improve interrupt handling for shared interrupts
scsi: ufs: Fix interrupt error message for shared interrupts
scsi: ufs-pci: Add quirk for broken auto-hibernate for Intel EHL
scsi: ufs-mediatek: Fix incorrect time to wait link status
...
|
|
Truncation of DMA_BIT_MASK to 32-bit dma_addr_t is semantically safe,
but the compiler was warning because it was happening implicitly.
Insert explicit casts to suppress the warnings.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gemini_ethernet_port_probe()
Replace alloc_etherdev_mq with devm_alloc_etherdev_mqs. In this way,
when probe fails, netdev can be freed automatically.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit
8dcf2ad39fdb2 ("net: atlantic: add hwmon getter for MAC temperature")
implemented a read callback with an udelay(10000U). This fails to
compile on ARM because the delay is >1ms. I doubt that it is needed to
spin for 10ms even if possible on x86.
>From looking at the code, the context appears to be preemptible so using
usleep() should work and avoid busy spinning.
Use readx_poll_timeout() in the poll loop.
Fixes: 8dcf2ad39fdb2 ("net: atlantic: add hwmon getter for MAC temperature")
Cc: Mark Starovoytov <mstarovoitov@marvell.com>
Cc: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most statistics in ena driver are incremented, meaning that a stat's
value is a sum of all increases done to it since driver/queue
initialization.
This patch makes all statistics this way, effectively making missed_tx
statistic incremental.
Also added a comment regarding rx_drops and tx_drops to make it
clearer how these counters are calculated.
Fixes: 11095fdb712b ("net: ena: add statistics for missed tx packets")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ena_del_napi_in_range() function unregisters the napi handler for
rings in a given range.
This function had the following WARN_ON macro:
WARN_ON(ENA_IS_XDP_INDEX(adapter, i) &&
adapter->ena_napi[i].xdp_ring);
This macro prints the call stack if the expression inside of it is
true [1], but the expression inside of it is the wanted situation.
The expression checks whether the ring has an XDP queue and its index
corresponds to a XDP one.
This patch changes the expression to
!ENA_IS_XDP_INDEX(adapter, i) && adapter->ena_napi[i].xdp_ring
which indicates an unwanted situation.
Also, change the structure of the function. The napi handler is
unregistered for all rings, and so there's no need to check whether the
index is an XDP index or not. By removing this check the code becomes
much more readable.
Fixes: 548c4940b9f1 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset work is scheduled by the timer routine whenever it
detects that a device reset is required (e.g. when a keep_alive signal
is missing).
When releasing device resources in ena_destroy_device() the driver
cancels the scheduling of the timer routine without destroying the reset
work explicitly.
This creates the following bug:
The driver is suspended and the ena_suspend() function is called
-> This function calls ena_destroy_device() to free the net device
resources
-> The driver waits for the timer routine to finish
its execution and then cancels it, thus preventing from it
to be called again.
If, in its final execution, the timer routine schedules a reset,
the reset routine might be called afterwards,and a redundant call to
ena_restore_device() would be made.
By changing the reset routine we allow it to read the device's state
accurately.
This is achieved by checking whether ENA_FLAG_TRIGGER_RESET flag is set
before resetting the device and making both the destruction function and
the flag check are under rtnl lock.
The ENA_FLAG_TRIGGER_RESET is cleared at the end of the destruction
routine. Also surround the flag check with 'likely' because
we expect that the reset routine would be called only when
ENA_FLAG_TRIGGER_RESET flag is set.
The destruction of the timer and reset services in __ena_shutoff() have to
stay, even though the timer routine is destroyed in ena_destroy_device().
This is to avoid a case in which the reset routine is scheduled after
free_netdev() in __ena_shutoff(), which would create an access to freed
memory in adapter->flags.
Fixes: 8c5c7abdeb2d ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even after Tx queues are marked stopped, there exists a
small window where the current packet in the normal Tx
path is still being sent out and loopback selftest ends
up corrupting the same Tx ring. So, ensure selftest takes
the Tx lock to synchronize access the Tx ring.
Fixes: 7235ffae3d2c ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Work request used for sending loopback packet needs to add
the firmware work request only once. So, fix by using
correct structure size.
Fixes: 7235ffae3d2c ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If efx_nic_init_interrupt fails, or was never run (e.g. due to an earlier
failure in ef100_net_open), freeing irqs in efx_nic_fini_interrupt is not
needed and will cause error messages and stack traces.
So instead, only do this if efx_nic_init_interrupt successfully completed,
as indicated by the new efx->irqs_hooked flag.
Fixes: 965b549f3c20 ("sfc_ef100: implement ndo_open/close and EVQ probing")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an ef100_net_open() fails, ef100_net_stop() may be called without
channel->rps_flow_id having been written; thus it may hold the address
freed by a previous ef100_net_stop()'s call to efx_remove_filters().
This then causes a double-free when efx_remove_filters() is called
again, leading to a panic.
To prevent this, after freeing it, overwrite it with NULL.
Fixes: a9dc3d5612ce ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When downing and upping the ef100 filter table, we need to take a write
lock on efx->filter_sem, not just a read lock, because we may kfree()
the table pointers.
Without this, resets cause a WARN_ON from efx_rwsem_assert_write_locked().
Fixes: a9dc3d5612ce ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Actually hook up the .rx_buf_hash_valid method in EF100's nic_type.
Fixes: 068885434ccb ("sfc: check hash is valid before using it")
Reported-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ixgbe_fcoe_ddp_setup() can be called from the main I/O path and is called
with a spin_lock held, so we have to use GFP_ATOMIC allocation instead of
GFP_KERNEL.
Link: https://lore.kernel.org/r/1596831813-9839-1-git-send-email-michael.christie@oracle.com
cc: Hannes Reinecke <hare@suse.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/8390/axnet_cs.c:907: warning: Function parameter or member 'txqueue' not described in 'axnet_tx_timeout'
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Shannon Nelson <snelson@pensando.io>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: William Lee <william@asix.com.tw>
Cc: "A. Hinds --" <dahinds@users.sourceforge.net>
Cc: reached at <becker@scyld.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Bruce Ashfield
Linus Torvalds
Michael Chan
Louis Peens
Dan Carpenter
Denis Efremov
Shyam Sundar S K
Shung-Hsi Yu
Grygorii Strashko
Potnuri Bharat Teja
Shannon Nelson
Murali Karicheri
Jakub Kicinski
Yi Li
Edwin Peer
Vasundhara Volam
Pavan Chebbi
Mingming Cao
Edward Cree
Dinghao Liu
Yuusuke Ashizuka
Gustavo A. R. Silva
Wang Hai
Sebastian Andrzej Siewior
Shay Agroskin
Sumera Priyadarsini
Ganji Aravind
Mike Christie
Xu Wang
Lee Jones