aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2019-09-16net/mlx5: Avoid reloading already removed devicesAlaa Hleihel
commit dd80857bf388abd0c64dd3aa4fbf7d407deba819 upstream. Prior to reloading a device we must first verify that it was not already removed. Otherwise, the attempt to remove the device will do nothing, and in that case we will end up proceeding with adding an new device that no one was expecting to remove, leaving behind used resources such as EQs that causes a failure to destroy comp EQs and syndrome (0x30f433). Fix that by making sure that we try to remove and add a device (based on a protocol) only if the device is already added. Fixes: c5447c70594b ("net/mlx5: E-Switch, Reload IB interface when switching devlink modes") Signed-off-by: Alaa Hleihel <alaa@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16mlxsw: spectrum: Prevent force of 56GAmit Cohen
commit 275e928f19117d22f6d26dee94548baf4041b773 upstream. Force of 56G is not supported by hardware in Ethernet devices. This configuration fails with a bad parameter error from firmware. Add check of this case. Instead of trying to set 56G with autoneg off, return a meaningful error. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Amit Cohen <amitc@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: sh_eth: fix mdio access in sh_eth_close() for R-Car Gen2 and RZ/A1 SoCsYoshihiro Shimoda
commit 315ca92dd863fecbffc0bb52ae0ac11e0398726a upstream. The sh_eth_close() resets the MAC and then calls phy_stop() so that mdio read access result is incorrect without any error according to kernel trace like below: ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff According to the hardware manual, the RMII mode should be set to 1 before operation the Ethernet MAC. However, the previous code was not set to 1 after the driver issued the soft_reset in sh_eth_dev_exit() so that the mdio read access result seemed incorrect. To fix the issue, this patch adds a condition and set the RMII mode register in sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs. Note that when I have tried to move the sh_eth_dev_exit() calling after phy_stop() on sh_eth_close(), but it gets worse (kernel panic happened and it seems that a register is accessed while the clock is off). Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: aquantia: fix LRO with FCS errorDmitry Bogdanov
commit eaeb3b7494ba9159323814a8ce8af06a9277d99b upstream. Driver stops producing skbs on ring if a packet with FCS error was coalesced into LRO session. Ring gets hang forever. Thats a logical error in driver processing descriptors: When rx_stat indicates MAC Error, next pointer and eop flags are not filled. This confuses driver so it waits for descriptor 0 to be filled by HW. Solution is fill next pointer and eop flag even for packets with FCS error. Fixes: bab6de8fd180b ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: aquantia: tx clean budget logic errorIgor Russkikh
commit 31bafc49a7736989e4c2d9f7280002c66536e590 upstream. In case no other traffic happening on the ring, full tx cleanup may not be completed. That may cause socket buffer to overflow and tx traffic to stuck until next activity on the ring happens. This is due to logic error in budget variable decrementor. Variable is compared with zero, and then post decremented, causing it to become MAX_INT. Solution is remove decrementor from the `for` statement and rewrite it in a clear way. Fixes: b647d3980948e ("net: aquantia: Add tx clean budget and valid budget handling logic") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: tulip: de4x5: Drop redundant MODULE_DEVICE_TABLE()Kees Cook
commit 3e66b7cc50ef921121babc91487e1fb98af1ba6e upstream. Building with Clang reports the redundant use of MODULE_DEVICE_TABLE(): drivers/net/ethernet/dec/tulip/de4x5.c:2110:1: error: redefinition of '__mod_eisa__de4x5_eisa_ids_device_table' MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids); ^ ./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE' extern typeof(name) __mod_##type##__##name##_device_table \ ^ <scratch space>:90:1: note: expanded from here __mod_eisa__de4x5_eisa_ids_device_table ^ drivers/net/ethernet/dec/tulip/de4x5.c:2100:1: note: previous definition is here MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids); ^ ./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE' extern typeof(name) __mod_##type##__##name##_device_table \ ^ <scratch space>:85:1: note: expanded from here __mod_eisa__de4x5_eisa_ids_device_table ^ This drops the one further from the table definition to match the common use of MODULE_DEVICE_TABLE(). Fixes: 07563c711fbc ("EISA bus MODALIAS attributes support") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: stmmac: update rx tail pointer register to fix rx dma hang issue.Biao Huang
commit 4523a5611526709ec9b4e2574f1bb7818212651e upstream. Currently we will not update the receive descriptor tail pointer in stmmac_rx_refill. Rx dma will think no available descriptors and stop once received packets exceed DMA_RX_SIZE, so that the rx only test will fail. Update the receive tail pointer in stmmac_rx_refill to add more descriptors to the rx channel, so packets can be received continually Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx") Signed-off-by: Biao Huang <biao.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: mvpp2: prs: Use the correct helpers when removing all VID filtersMaxime Chevallier
commit 6b7a3430c163455cf8a514d636bda52b04654972 upstream. When removing all VID filters, the mvpp2_prs_vid_entry_remove would be called with the TCAM id incorrectly used as a VID, causing the wrong TCAM entries to be invalidated. Fix this by directly invalidating entries in the VID range. Fixes: 56beda3db602 ("net: mvpp2: Add hardware offloading for VLAN filtering") Suggested-by: Yuri Chipchev <yuric@marvell.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: mvpp2: prs: Fix parser range for VID filteringMaxime Chevallier
commit 46b0090a6636cf34c0e856f15dd03e15ba4cdda6 upstream. VID filtering is implemented in the Header Parser, with one range of 11 vids being assigned for each no-loopback port. Make sure we use the per-port range when looking for existing entries in the Parser. Since we used a global range instead of a per-port one, this causes VIDs to be removed from the whitelist from all ports of the same PPv2 instance. Fixes: 56beda3db602 ("net: mvpp2: Add hardware offloading for VLAN filtering") Suggested-by: Yuri Chipchev <yuric@marvell.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16be2net: Fix number of Rx queues used for flow hashingIvan Vecera
commit 718f4a2537089ea41903bf357071306163bc7c04 upstream. Number of Rx queues used for flow hashing returned by the driver is incorrect and this bug prevents user to use the last Rx queue in indirection table. Let's say we have a NIC with 6 combined queues: [root@sm-03 ~]# ethtool -l enp4s0f0 Channel parameters for enp4s0f0: Pre-set maximums: RX: 5 TX: 5 Other: 0 Combined: 6 Current hardware settings: RX: 0 TX: 0 Other: 0 Combined: 6 Default indirection table maps all (6) queues equally but the driver reports only 5 rings available. [root@sm-03 ~]# ethtool -x enp4s0f0 RX flow hash indirection table for enp4s0f0 with 5 RX ring(s): 0: 0 1 2 3 4 5 0 1 8: 2 3 4 5 0 1 2 3 16: 4 5 0 1 2 3 4 5 24: 0 1 2 3 4 5 0 1 ... Now change indirection table somehow: [root@sm-03 ~]# ethtool -X enp4s0f0 weight 1 1 [root@sm-03 ~]# ethtool -x enp4s0f0 RX flow hash indirection table for enp4s0f0 with 6 RX ring(s): 0: 0 0 0 0 0 0 0 0 ... 64: 1 1 1 1 1 1 1 1 ... Now it is not possible to change mapping back to equal (default) state: [root@sm-03 ~]# ethtool -X enp4s0f0 equal 6 Cannot set RX flow hash configuration: Invalid argument Fixes: 594ad54a2c3b ("be2net: Add support for setting and getting rx flow hash options") Reported-by: Tianhao <tizhao@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16ice: Add missing case in print_link_msg for printing flow controlBrett Creeley
commit 203a068ac9e2722e4d118116acaa3a5586f9468a upstream. Currently we aren't checking for the ICE_FC_NONE case for the current flow control mode. This is causing "Unknown" to be printed for the current flow control method if flow control is disabled. Fix this by adding the case for ICE_FC_NONE to print "None". Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16net: hns3: return 0 and print warning when hit duplicate MACPeng Li
commit 72110b567479f0282489a9b3747e76d8c67d75f5 upstream. When set 2 same MAC to different function of one port, IMP will return error as the later one may modify the origin one. This will cause bond fail for 2 VFs of one port. Driver just print warning and return 0 with this patch, so if set same MAC address, it will return 0 but do not really configure HW. Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-16i40e: Queues are reserved despite "Invalid argument" errorAdam Ludkiewicz
commit 3e957b377bf4262aec2dd424f28ece94e36814d4 upstream. Added a new local variable in the i40e_setup_tc function named old_queue_pairs so num_queue_pairs can be restored to the correct value in case configuring queue channels fails. Additionally, moved the exit label in the i40e_setup_tc function so the if (need_reset) block can be executed. Also, fixed data packing in the i40e_setup_tc function. Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net: mvpp2: Use strscpy to handle stat stringsMaxime Chevallier
commit d37acd5aa99c57505b64913e0e2624ec3daed8c5 upstream. Use a safe strscpy call to copy the ethtool stat strings into the relevant buffers, instead of a memcpy that will be accessing out-of-bound data. Fixes: 118d6298f6f0 ("net: mvpp2: add ethtool GOP statistics") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages queryErez Alfasi
commit 135dd9594f127c8a82d141c3c8430e9e2143216a upstream. Querying EEPROM high pages data for SFP module is currently not supported by our driver but is still tried, resulting in invalid FW queries. Set the EEPROM ethtool data length to 256 for SFP module to limit the reading for page 0 only and prevent invalid FW queries. Fixes: 7202da8b7f71 ("ethtool, net/mlx4_en: Cable info, get_module_info/eeprom ethtool support") Signed-off-by: Erez Alfasi <ereza@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net/mlx5e: Disable rxhash when CQE compress is enabledSaeed Mahameed
commit c0194e2d0ef0e5ce5e21a35640d23a706827ae28 upstream. When CQE compression is enabled (Multi-host systems), compressed CQEs might arrive to the driver rx, compressed CQEs don't have a valid hash offload and the driver already reports a hash value of 0 and invalid hash type on the skb for compressed CQEs, but this is not good enough. On a congested PCIe, where CQE compression will kick in aggressively, gro will deliver lots of out of order packets due to the invalid hash and this might cause a serious performance drop. The only valid solution, is to disable rxhash offload at all when CQE compression is favorable (Multi-host systems). Fixes: 7219ab34f184 ("net/mlx5e: CQE compression") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net/mlx5: Allocate root ns memory using kzalloc to match kfreeParav Pandit
commit 25fa506b70cadb580c1e9cbd836d6417276d4bcd upstream. root ns is yet another fs core node which is freed using kfree() by tree_put_node(). Rest of the other fs core objects are also allocated using kmalloc variants. However, root ns memory is allocated using kvzalloc(). Hence allocate root ns memory using kzalloc(). Fixes: 2530236303d9e ("net/mlx5_core: Flow steering tree initialization") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net/mlx5: Avoid double free in fs init error unwinding pathParav Pandit
commit 9414277a5df3669c67e818708c0f881597e0118e upstream. In below code flow, for ingress acl table root ns memory leads to double free. mlx5_init_fs init_ingress_acls_root_ns() init_ingress_acl_root_ns kfree(steering->esw_ingress_root_ns); /* steering->esw_ingress_root_ns is not marked NULL */ mlx5_cleanup_fs cleanup_ingress_acls_root_ns steering->esw_ingress_root_ns non NULL check passes. kfree(steering->esw_ingress_root_ns); /* double free */ Similar issue exist for other tables. Hence zero out the pointers to not process the table again. Fixes: 9b93ab981e3bf ("net/mlx5: Separate ingress/egress namespaces for each vport") Fixes: 40c3eebb49e51 ("net/mlx5: Add support in RDMA RX steering") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net: stmmac: fix reset gpio free missingJisheng Zhang
commit 49ce881c0d4c4a7a35358d9dccd5f26d0e56fc61 upstream. Commit 984203ceff27 ("net: stmmac: mdio: remove reset gpio free") removed the reset gpio free, when the driver is unbinded or rmmod, we miss the gpio free. This patch uses managed API to request the reset gpio, so that the gpio could be freed properly. Fixes: 984203ceff27 ("net: stmmac: mdio: remove reset gpio free") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue valueAntoine Tenart
commit 21808437214637952b61beaba6034d97880fbeb3 upstream. MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but the current code is passing the global tx queue offset, so it ends up writing to unknown registers (between 0x8280 and 0x82fc, which seemed to be unused by the hardware). This fixes the issue by using the logical queue id instead. Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net: mvneta: Fix err code path of probeJisheng Zhang
commit d484e06e25ebb937d841dac02ac1fe76ec7d4ddd upstream. Fix below issues in err code path of probe: 1. we don't need to unregister_netdev() because the netdev isn't registered. 2. when register_netdev() fails, we also need to destroy bm pool for HWBM case. Fixes: dc35a10f68d3 ("net: mvneta: bm: add support for hardware buffer management") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12net: fec: fix the clk mismatch in failed_reset pathAndy Duan
commit ce8d24f9a5965a58c588f9342689702a1024433c upstream. Fix the clk mismatch in the error path "failed_reset" because below error path will disable clk_ahb and clk_ipg directly, it should use pm_runtime_put_noidle() instead of pm_runtime_put() to avoid to call runtime resume callback. Reported-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Tested-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-09-12cxgb4: offload VLAN flows regardless of VLAN ethtypeRaju Rangoju
commit b5730061d1056abf317caea823b94d6e12b5b4f6 upstream. VLAN flows never get offloaded unless ivlan_vld is set in filter spec. It's not compulsory for vlan_ethtype to be set. So, always enable ivlan_vld bit for offloading VLAN flows regardless of vlan_ethtype is set or not. Fixes: ad9af3e09c (cxgb4: add tc flower match support for vlan) Signed-off-by: Raju Rangoju <rajur@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-17igb: Exclude device from suspend direct complete optimizationKai-Heng Feng
commit 5b6e13216be29ced7350d9c354a1af8fe0ad9a3e upstream. igb sets different WoL settings in system suspend callback and runtime suspend callback. The suspend direct complete optimization leaves igb in runtime suspended state with wrong WoL setting during system suspend. To fix this, we need to disable suspend direct complete optimization to let igb always use suspend callback to set correct WoL during system suspend. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-17e1000e: Disable runtime PM on CNP+Kai-Heng Feng
commit 459d69c407f9ba122f12216555c3012284dc9fd7 upstream. There are some new e1000e devices can only be woken up from D3 one time, by plugging Ethernet cable. Subsequent cable plugging does set PME bit correctly, but it still doesn't get woken up. Since e1000e connects to the root complex directly, we rely on ACPI to wake it up. In this case, the GPE from _PRW only works once and stops working after that. Though it appears to be a platform bug, e1000e maintainers confirmed that I219 does not support D3. So disable runtime PM on CNP+ chips. We may need to disable earlier generations if this bug also hit older platforms. Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-17cxgb3/l2t: Fix undefined behaviourGustavo A. R. Silva
commit 76497732932f15e7323dc805e8ea8dc11bb587cf upstream. The use of zero-sized array causes undefined behaviour when it is not the last member in a structure. As it happens to be in this case. Also, the current code makes use of a language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as this one is a flexible array member, introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last. Which is beneficial to cultivate a high-quality code. Fixes: e48f129c2f20 ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-17i40e: don't allow changes to HW VLAN stripping on active port VLANsNicholas Nunley
commit bfb0ebed53857cfc57f11c63fa3689940d71c1c8 upstream. Modifying the VLAN stripping options when a port VLAN is configured will break traffic for the VSI, and conceptually doesn't make sense, so don't allow this. Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-17i40e: Able to add up to 16 MAC filters on an untrusted VFAdam Ludkiewicz
commit 06b6e2a2333eb3581567a7ac43ca465ef45f4daa upstream. This patch fixes the problem with the driver being able to add only 7 multicast MAC address filters instead of 16. The problem is fixed by changing the maximum number of MAC address filters to 16+1+1 (two extra are needed because the driver uses 1 for unicast MAC address and 1 for broadcast). Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-02net: ena: gcc 8: fix compilation warningSameeh Jubran
commit f913308879bc6ae437ce64d878c7b05643ddea44 upstream. GCC 8 contains a number of new warnings as well as enhancements to existing checkers. The warning - Wstringop-truncation - warns for calls to bounded string manipulation functions such as strncat, strncpy, and stpncpy that may either truncate the copied string or leave the destination unchanged. In our case the destination string length (32 bytes) is much shorter than the source string (64 bytes) which causes this warning to show up. In general the destination has to be at least a byte larger than the length of the source string with strncpy for this warning not to showup. This can be easily fixed by using strlcpy instead which already does the truncation to the string. Documentation for this function can be found here: https://elixir.bootlin.com/linux/latest/source/lib/string.c#L141 Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-02cxgb4: Fix error path in cxgb4_init_moduleYueHaibing
commit a3147770bea76c8dbad73eca3a24c2118da5e719 upstream. BUG: unable to handle kernel paging request at ffffffffa016a270 PGD 3270067 P4D 3270067 PUD 3271063 PMD 230bbd067 PTE 0 Oops: 0000 [#1 CPU: 0 PID: 6134 Comm: modprobe Not tainted 5.1.0+ #33 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014 RIP: 0010:atomic_notifier_chain_register+0x24/0x60 Code: 1f 80 00 00 00 00 55 48 89 e5 41 54 49 89 f4 53 48 89 fb e8 ae b4 38 01 48 8b 53 38 48 8d 4b 38 48 85 d2 74 20 45 8b 44 24 10 <44> 3b 42 10 7e 08 eb 13 44 39 42 10 7c 0d 48 8d 4a 08 48 8b 52 08 RSP: 0018:ffffc90000e2bc60 EFLAGS: 00010086 RAX: 0000000000000292 RBX: ffffffff83467240 RCX: ffffffff83467278 RDX: ffffffffa016a260 RSI: ffffffff83752140 RDI: ffffffff83467240 RBP: ffffc90000e2bc70 R08: 0000000000000000 R09: 0000000000000001 R10: 0000000000000000 R11: 00000000014fa61f R12: ffffffffa01c8260 R13: ffff888231091e00 R14: 0000000000000000 R15: ffffc90000e2be78 FS: 00007fbd8d7cd540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffa016a270 CR3: 000000022c7e3000 CR4: 00000000000006f0 Call Trace: register_inet6addr_notifier+0x13/0x20 cxgb4_init_module+0x6c/0x1000 [cxgb4 ? 0xffffffffa01d7000 do_one_initcall+0x6c/0x3cc ? do_init_module+0x22/0x1f1 ? rcu_read_lock_sched_held+0x97/0xb0 ? kmem_cache_alloc_trace+0x325/0x3b0 do_init_module+0x5b/0x1f1 load_module+0x1db1/0x2690 ? m_show+0x1d0/0x1d0 __do_sys_finit_module+0xc5/0xd0 __x64_sys_finit_module+0x15/0x20 do_syscall_64+0x6b/0x1d0 entry_SYSCALL_64_after_hwframe+0x49/0xbe If pci_register_driver fails, register inet6addr_notifier is pointless. This patch fix the error path in cxgb4_init_module. Fixes: b5a02f503caa ("cxgb4 : Update ipv6 address handling api") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-02net/mlx5: Imply MLXFW in mlx5_coreSaeed Mahameed
commit bad861f31bb15a99becef31aab59640eaeb247e2 upstream. mlxfw can be compiled as external module while mlx5_core can be builtin, in such case mlx5 will act like mlxfw is disabled. Since mlxfw is just a service library for mlx* drivers, imply it in mlx5_core to make it always reachable if it was enabled. Fixes: 3ffaabecd1a1 ("net/mlx5e: Support the flash device ethtool callback") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-02nfp: flower: add rcu locks when accessing netdev for tunnelsPieter Jansen van Vuuren
commit cb07d915bf278a7a3938b983bbcb4921366b5eff upstream. Add rcu locks when accessing netdev when processing route request and tunnel keep alive messages received from hardware. Fixes: 8e6a9046b66a ("nfp: flower vxlan neighbour offload") Fixes: 856f5b135758 ("nfp: flower vxlan neighbour keep-alive") Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-08-02net/mlx4_core: Change the error print to info printYunjian Wang
commit 00f9fec48157f3734e52130a119846e67a12314b upstream. The error print within mlx4_flow_steer_promisc_add() should be a info print. Fixes: 592e49dda812 ('net/mlx4: Implement promiscuous mode with device managed flow-steering') Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30net: ucc_geth - fix Oops when changing number of buffers in the ringChristophe Leroy
commit ee0df19305d9fabd9479b785918966f6e25b733b upstream. When changing the number of buffers in the RX ring while the interface is running, the following Oops is encountered due to the new number of buffers being taken into account immediately while their allocation is done when opening the device only. [ 69.882706] Unable to handle kernel paging request for data at address 0xf0000100 [ 69.890172] Faulting instruction address: 0xc033e164 [ 69.895122] Oops: Kernel access of bad area, sig: 11 [#1] [ 69.900494] BE PREEMPT CMPCPRO [ 69.907120] CPU: 0 PID: 0 Comm: swapper Not tainted 4.14.115-00006-g179ade8ce3-dirty #269 [ 69.915956] task: c0684310 task.stack: c06da000 [ 69.920470] NIP: c033e164 LR: c02e44d0 CTR: c02e41fc [ 69.925504] REGS: dfff1e20 TRAP: 0300 Not tainted (4.14.115-00006-g179ade8ce3-dirty) [ 69.934161] MSR: 00009032 <EE,ME,IR,DR,RI> CR: 22004428 XER: 20000000 [ 69.940869] DAR: f0000100 DSISR: 20000000 [ 69.940869] GPR00: c0352d70 dfff1ed0 c0684310 f00000a4 00000040 dfff1f68 00000000 0000001f [ 69.940869] GPR08: df53f410 1cc00040 00000021 c0781640 42004424 100c82b6 f00000a4 df53f5b0 [ 69.940869] GPR16: df53f6c0 c05daf84 00000040 00000000 00000040 c0782be4 00000000 00000001 [ 69.940869] GPR24: 00000000 df53f400 000001b0 df53f410 df53f000 0000003f df708220 1cc00044 [ 69.978348] NIP [c033e164] skb_put+0x0/0x5c [ 69.982528] LR [c02e44d0] ucc_geth_poll+0x2d4/0x3f8 [ 69.987384] Call Trace: [ 69.989830] [dfff1ed0] [c02e4554] ucc_geth_poll+0x358/0x3f8 (unreliable) [ 69.996522] [dfff1f20] [c0352d70] net_rx_action+0x248/0x30c [ 70.002099] [dfff1f80] [c04e93e4] __do_softirq+0xfc/0x310 [ 70.007492] [dfff1fe0] [c0021124] irq_exit+0xd0/0xd4 [ 70.012458] [dfff1ff0] [c000e7e0] call_do_irq+0x24/0x3c [ 70.017683] [c06dbe80] [c0006bac] do_IRQ+0x64/0xc4 [ 70.022474] [c06dbea0] [c001097c] ret_from_except+0x0/0x14 [ 70.027964] --- interrupt: 501 at rcu_idle_exit+0x84/0x90 [ 70.027964] LR = rcu_idle_exit+0x74/0x90 [ 70.037585] [c06dbf60] [20000000] 0x20000000 (unreliable) [ 70.042984] [c06dbf80] [c004bb0c] do_idle+0xb4/0x11c [ 70.047945] [c06dbfa0] [c004bd14] cpu_startup_entry+0x18/0x1c [ 70.053682] [c06dbfb0] [c05fb034] start_kernel+0x370/0x384 [ 70.059153] [c06dbff0] [00003438] 0x3438 [ 70.063062] Instruction dump: [ 70.066023] 38a00000 38800000 90010014 4bfff015 80010014 7c0803a6 3123ffff 7c691910 [ 70.073767] 38210010 4e800020 38600000 4e800020 <80e3005c> 80c30098 3107ffff 7d083910 [ 70.081690] ---[ end trace be7ccd9c1e1a9f12 ]--- This patch forbids the modification of the number of buffers in the ring while the interface is running. Fixes: ac421852b3a0 ("ucc_geth: add ethtool support") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30net: seeq: fix crash caused by not set dev.parentThomas Bogendoerfer
commit 5afcd14cfc7fed1bcc8abcee2cef82732772bfc2 upstream. The old MIPS implementation of dma_cache_sync() didn't use the dev argument, but commit c9eb6172c328 ("dma-mapping: turn dma_cache_sync into a dma_map_ops method") changed that, so we now need to set dev.parent. Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30net: macb: Change interrupt and napi enable order in openHarini Katakam
commit 0504453139ef5a593c9587e1e851febee859c7d8 upstream. Current order in open: -> Enable interrupts (macb_init_hw) -> Enable NAPI -> Start PHY Sequence of RX handling: -> RX interrupt occurs -> Interrupt is cleared and interrupt bits disabled in handler -> NAPI is scheduled -> In NAPI, RX budget is processed and RX interrupts are re-enabled With the above, on QEMU or fixed link setups (where PHY state doesn't matter), there's a chance macb RX interrupt occurs before NAPI is enabled. This will result in NAPI being scheduled before it is enabled. Fix this macb open by changing the order. Fixes: ae1f2a56d273 ("net: macb: Added support for many RX queues") Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30net: ethernet: stmmac: dwmac-sun8i: enable support of unicast filteringCorentin Labbe
commit d4c26eb6e721683a0f93e346ce55bc8dc3cbb175 upstream. When adding more MAC addresses to a dwmac-sun8i interface, the device goes directly in promiscuous mode. This is due to IFF_UNICAST_FLT missing flag. So since the hardware support unicast filtering, let's add IFF_UNICAST_FLT. Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30dpaa_eth: fix SG frame cleanupLaurentiu Tudor
commit 17170e6570c082717c142733d9a638bcd20551f8 upstream. Fix issue with the entry indexing in the sg frame cleanup code being off-by-1. This problem showed up when doing some basic iperf tests and manifested in traffic coming to a halt. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Acked-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw workqueueIdo Schimmel
commit b442fed1b724af0de087912a5718ddde1b87acbb upstream. The workqueue is used to periodically update the networking stack about activity / statistics of various objects such as neighbours and TC actions. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. Fixes: 3d5479e92087 ("mlxsw: core: Remove deprecated create_workqueue") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw ordered workqueueIdo Schimmel
commit 4af0699782e2cc7d0d89db9eb6f8844dd3df82dc upstream. The ordered workqueue is used to offload various objects such as routes and neighbours in the order they are notified. It should not be called as part of memory reclaim path, so remove the WQ_MEM_RECLAIM flag. This can also result in a warning [1], if a worker tries to flush a non-WQ_MEM_RECLAIM workqueue. [1] [97703.542861] workqueue: WQ_MEM_RECLAIM mlxsw_core_ordered:mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] is flushing !WQ_MEM_RECLAIM events:rht_deferred_worker [97703.542884] WARNING: CPU: 1 PID: 32492 at kernel/workqueue.c:2605 check_flush_dependency+0xb5/0x130 ... [97703.542988] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 [97703.543049] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] [97703.543061] RIP: 0010:check_flush_dependency+0xb5/0x130 ... [97703.543071] RSP: 0018:ffffb3f08137bc00 EFLAGS: 00010086 [97703.543076] RAX: 0000000000000000 RBX: ffff96e07740ae00 RCX: 0000000000000000 [97703.543080] RDX: 0000000000000094 RSI: ffffffff82dc1934 RDI: 0000000000000046 [97703.543084] RBP: ffffb3f08137bc20 R08: ffffffff82dc18a0 R09: 00000000000225c0 [97703.543087] R10: 0000000000000000 R11: 0000000000007eec R12: ffffffff816e4ee0 [97703.543091] R13: ffff96e06f6a5c00 R14: ffff96e077ba7700 R15: ffffffff812ab0c0 [97703.543097] FS: 0000000000000000(0000) GS:ffff96e077a80000(0000) knlGS:0000000000000000 [97703.543101] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [97703.543104] CR2: 00007f8cd135b280 CR3: 00000001e860e003 CR4: 00000000003606e0 [97703.543109] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [97703.543112] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [97703.543115] Call Trace: [97703.543129] __flush_work+0xbd/0x1e0 [97703.543137] ? __cancel_work_timer+0x136/0x1b0 [97703.543145] ? pwq_dec_nr_in_flight+0x49/0xa0 [97703.543154] __cancel_work_timer+0x136/0x1b0 [97703.543175] ? mlxsw_reg_trans_bulk_wait+0x145/0x400 [mlxsw_core] [97703.543184] cancel_work_sync+0x10/0x20 [97703.543191] rhashtable_free_and_destroy+0x23/0x140 [97703.543198] rhashtable_destroy+0xd/0x10 [97703.543254] mlxsw_sp_fib_destroy+0xb1/0xf0 [mlxsw_spectrum] [97703.543310] mlxsw_sp_vr_put+0xa8/0xc0 [mlxsw_spectrum] [97703.543364] mlxsw_sp_fib_node_put+0xbf/0x140 [mlxsw_spectrum] [97703.543418] ? mlxsw_sp_fib6_entry_destroy+0xe8/0x110 [mlxsw_spectrum] [97703.543475] mlxsw_sp_router_fib6_event_work+0x6cd/0x7f0 [mlxsw_spectrum] [97703.543484] process_one_work+0x1fd/0x400 [97703.543493] worker_thread+0x34/0x410 [97703.543500] kthread+0x121/0x140 [97703.543507] ? process_one_work+0x400/0x400 [97703.543512] ? kthread_park+0x90/0x90 [97703.543523] ret_from_fork+0x35/0x40 Fixes: a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB offload") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Semion Lisyansky <semionl@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30mlxsw: core: Do not use WQ_MEM_RECLAIM for EMAD workqueueIdo Schimmel
commit a8c133b06183c529c51cd0d54eb57d6b7078370c upstream. The EMAD workqueue is used to handle retransmission of EMAD packets that contain configuration data for the device's firmware. Given the workers need to allocate these packets and that the code is not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM flag. Fixes: d965465b60ba ("mlxsw: core: Fix possible deadlock") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30mlxsw: spectrum_switchdev: Add MDB entries in prepare phaseIdo Schimmel
commit d4d0e40977ac450f32f2db5e4d8e23c9d2578899 upstream. The driver cannot guarantee in the prepare phase that it will be able to write an MDB entry to the device. In case the driver returned success during the prepare phase, but then failed to add the entry in the commit phase, a WARNING [1] will be generated by the switchdev core. Fix this by doing the work in the prepare phase instead. [1] [ 358.544486] swp12s0: Commit of object (id=2) failed. [ 358.550061] WARNING: CPU: 0 PID: 30 at net/switchdev/switchdev.c:281 switchdev_port_obj_add_now+0x9b/0xe0 [ 358.560754] CPU: 0 PID: 30 Comm: kworker/0:1 Not tainted 5.0.0-custom-13382-gf2449babf221 #1350 [ 358.570472] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016 [ 358.580582] Workqueue: events switchdev_deferred_process_work [ 358.587001] RIP: 0010:switchdev_port_obj_add_now+0x9b/0xe0 ... [ 358.614109] RSP: 0018:ffffa6b900d6fe18 EFLAGS: 00010286 [ 358.619943] RAX: 0000000000000000 RBX: ffff8b00797ff000 RCX: 0000000000000000 [ 358.627912] RDX: ffff8b00b7a1d4c0 RSI: ffff8b00b7a152e8 RDI: ffff8b00b7a152e8 [ 358.635881] RBP: ffff8b005c3f5bc0 R08: 000000000000022b R09: 0000000000000000 [ 358.643850] R10: 0000000000000000 R11: ffffa6b900d6fcc8 R12: 0000000000000000 [ 358.651819] R13: dead000000000100 R14: ffff8b00b65a23c0 R15: 0ffff8b00b7a2200 [ 358.659790] FS: 0000000000000000(0000) GS:ffff8b00b7a00000(0000) knlGS:0000000000000000 [ 358.668820] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 358.675228] CR2: 00007f00aad90de0 CR3: 00000001ca80d000 CR4: 00000000001006f0 [ 358.683188] Call Trace: [ 358.685918] switchdev_port_obj_add_deferred+0x13/0x60 [ 358.691655] switchdev_deferred_process+0x6b/0xf0 [ 358.696907] switchdev_deferred_process_work+0xa/0x10 [ 358.702548] process_one_work+0x1f5/0x3f0 [ 358.707022] worker_thread+0x28/0x3c0 [ 358.711099] ? process_one_work+0x3f0/0x3f0 [ 358.715768] kthread+0x10d/0x130 [ 358.719369] ? __kthread_create_on_node+0x180/0x180 [ 358.724815] ret_from_fork+0x35/0x40 Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Kushnarov <alexanderk@mellanox.com> Tested-by: Alex Kushnarov <alexanderk@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30net: fec: manage ahb clock in runtime pmAndy Duan
commit d7c3a206e6338e4ccdf030719dec028e26a521d5 upstream. Some SOC like i.MX6SX clock have some limits: - ahb clock should be disabled before ipg. - ahb and ipg clocks are required for MAC MII bus. So, move the ahb clock to runtime management together with ipg clock. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30ocelot: Don't sleep in atomic context (irqs_disabled())Claudiu Manoil
commit a8fd48b50deaa20808bbf0f6685f6f1acba6a64c upstream. Preemption disabled at: [<ffff000008cabd54>] dev_set_rx_mode+0x1c/0x38 Call trace: [<ffff00000808a5c0>] dump_backtrace+0x0/0x3d0 [<ffff00000808a9a4>] show_stack+0x14/0x20 [<ffff000008e6c0c0>] dump_stack+0xac/0xe4 [<ffff0000080fe76c>] ___might_sleep+0x164/0x238 [<ffff0000080fe890>] __might_sleep+0x50/0x88 [<ffff0000082261e4>] kmem_cache_alloc+0x17c/0x1d0 [<ffff000000ea0ae8>] ocelot_set_rx_mode+0x108/0x188 [mscc_ocelot_common] [<ffff000008cabcf0>] __dev_set_rx_mode+0x58/0xa0 [<ffff000008cabd5c>] dev_set_rx_mode+0x24/0x38 Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30qede: fix write to free'd pointer error and double free of ptpColin Ian King
commit 1dc2b3d65523780ed1972d446c76e62e13f3e8f5 upstream. The err2 error return path calls qede_ptp_disable that cleans up on an error and frees ptp. After this, the free'd ptp is dereferenced when ptp->clock is set to NULL and the code falls-through to error path err1 that frees ptp again. Fix this by calling qede_ptp_disable and exiting via an error return path that does not set ptp->clock or kfree ptp. Addresses-Coverity: ("Write to pointer after free") Fixes: 035744975aec ("qede: Add support for PTP resource locking.") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-30vxge: fix return of a free'd memblock on a failed dma mappingColin Ian King
commit 0a2c34f18c94b596562bf3d019fceab998b8b584 upstream. Currently if a pci dma mapping failure is detected a free'd memblock address is returned rather than a NULL (that indicates an error). Fix this by ensuring NULL is returned on this error case. Addresses-Coverity: ("Use after free") Fixes: 528f727279ae ("vxge: code cleanup and reorganization") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-23libcxgb: fix incorrect ppmax calculationVarun Prakash
commit cc5a726c79158bd307150e8d4176ec79b52001ea upstream. BITS_TO_LONGS() uses DIV_ROUND_UP() because of this ppmax value can be greater than available per cpu page pods. This patch removes BITS_TO_LONGS() to fix this issue. Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-23net: hns: fix unsigned comparison to less than zeroColin Ian King
commit ea401685a20b5d631957f024bda86e1f6118eb20 upstream. Currently mskid is unsigned and hence comparisons with negative error return values are always false. Fix this by making mskid an int. Fixes: f058e46855dc ("net: hns: fix ICMP6 neighbor solicitation messages discard problem") Addresses-Coverity: ("Operands don't affect result") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-23net: hns: Fix WARNING when remove HNS driver with SMMU enabledYonglong Liu
commit 8601a99d7c0256b7a7fdd1ab14cf6c1f1dfcadc6 upstream. When enable SMMU, remove HNS driver will cause a WARNING: [ 141.924177] WARNING: CPU: 36 PID: 2708 at drivers/iommu/dma-iommu.c:443 __iommu_dma_unmap+0xc0/0xc8 [ 141.954673] Modules linked in: hns_enet_drv(-) [ 141.963615] CPU: 36 PID: 2708 Comm: rmmod Tainted: G W 5.0.0-rc1-28723-gb729c57de95c-dirty #32 [ 141.983593] Hardware name: Huawei D05/D05, BIOS Hisilicon D05 UEFI Nemo 1.8 RC0 08/31/2017 [ 142.000244] pstate: 60000005 (nZCv daif -PAN -UAO) [ 142.009886] pc : __iommu_dma_unmap+0xc0/0xc8 [ 142.018476] lr : __iommu_dma_unmap+0xc0/0xc8 [ 142.027066] sp : ffff000013533b90 [ 142.033728] x29: ffff000013533b90 x28: ffff8013e6983600 [ 142.044420] x27: 0000000000000000 x26: 0000000000000000 [ 142.055113] x25: 0000000056000000 x24: 0000000000000015 [ 142.065806] x23: 0000000000000028 x22: ffff8013e66eee68 [ 142.076499] x21: ffff8013db919800 x20: 0000ffffefbff000 [ 142.087192] x19: 0000000000001000 x18: 0000000000000007 [ 142.097885] x17: 000000000000000e x16: 0000000000000001 [ 142.108578] x15: 0000000000000019 x14: 363139343a70616d [ 142.119270] x13: 6e75656761705f67 x12: 0000000000000000 [ 142.129963] x11: 00000000ffffffff x10: 0000000000000006 [ 142.140656] x9 : 1346c1aa88093500 x8 : ffff0000114de4e0 [ 142.151349] x7 : 6662666578303d72 x6 : ffff0000105ffec8 [ 142.162042] x5 : 0000000000000000 x4 : 0000000000000000 [ 142.172734] x3 : 00000000ffffffff x2 : ffff0000114de500 [ 142.183427] x1 : 0000000000000000 x0 : 0000000000000035 [ 142.194120] Call trace: [ 142.199030] __iommu_dma_unmap+0xc0/0xc8 [ 142.206920] iommu_dma_unmap_page+0x20/0x28 [ 142.215335] __iommu_unmap_page+0x40/0x60 [ 142.223399] hnae_unmap_buffer+0x110/0x134 [ 142.231639] hnae_free_desc+0x6c/0x10c [ 142.239177] hnae_fini_ring+0x14/0x34 [ 142.246540] hnae_fini_queue+0x2c/0x40 [ 142.254080] hnae_put_handle+0x38/0xcc [ 142.261619] hns_nic_dev_remove+0x54/0xfc [hns_enet_drv] [ 142.272312] platform_drv_remove+0x24/0x64 [ 142.280552] device_release_driver_internal+0x17c/0x20c [ 142.291070] driver_detach+0x4c/0x90 [ 142.298259] bus_remove_driver+0x5c/0xd8 [ 142.306148] driver_unregister+0x2c/0x54 [ 142.314037] platform_driver_unregister+0x10/0x18 [ 142.323505] hns_nic_dev_driver_exit+0x14/0xf0c [hns_enet_drv] [ 142.335248] __arm64_sys_delete_module+0x214/0x25c [ 142.344891] el0_svc_common+0xb0/0x10c [ 142.352430] el0_svc_handler+0x24/0x80 [ 142.359968] el0_svc+0x8/0x7c0 [ 142.366104] ---[ end trace 60ad1cd58e63c407 ]--- The tx ring buffer map when xmit and unmap when xmit done. So in hnae_init_ring() did not map tx ring buffer, but in hnae_fini_ring() have a unmap operation for tx ring buffer, which is already unmapped when xmit done, than cause this WARNING. The hnae_alloc_buffers() is called in hnae_init_ring(), so the hnae_free_buffers() should be in hnae_fini_ring(), not in hnae_free_desc(). In hnae_fini_ring(), adds a check is_rx_ring() as in hnae_init_ring(). When the ring buffer is tx ring, adds a piece of code to ensure that the tx ring is unmap. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2019-05-23net: hns: fix ICMP6 neighbor solicitation messages discard problemYonglong Liu
commit f058e46855dcbc28edb2ed4736f38a71fd19cadb upstream. ICMP6 neighbor solicitation messages will be discard by the Hip06 chips, because of not setting forwarding pool. Enable promisc mode has the same problem. This patch fix the wrong forwarding table configs for the multicast vague matching when enable promisc mode, and add forwarding pool for the forwarding table. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
generated by cgit 1.2.3-korg (git 2.39.0) at 2024-06-03 06:52:12 +0000