Age | Commit message (Collapse) | Author |
|
commit 1d63b8d66d146deaaedbe16c80de105f685ea012 upstream.
The SDMA engine used by TEMAC halts operation when it has finished
processing of the last buffer descriptor in the buffer ring.
Unfortunately, no interrupt event is generated when this happens,
so we need to setup another mechanism to make sure DMA operation is
restarted when enough buffers have been added to the ring.
Fixes: 92744989533c ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 770d9c67974c4c71af4beb786dc43162ad2a15ba upstream.
Failures caused by GFP_ATOMIC memory pressure have been observed, and
due to the missing error handling, results in kernel crash such as
[1876998.350133] kernel BUG at mm/slub.c:3952!
[1876998.350141] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[1876998.350147] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.3.0-scnxt #1
[1876998.350150] Hardware name: N/A N/A/COMe-bIP2, BIOS CCR2R920 03/01/2017
[1876998.350160] RIP: 0010:kfree+0x1ca/0x220
[1876998.350164] Code: 85 db 74 49 48 8b 95 68 01 00 00 48 31 c2 48 89 10 e9 d7 fe ff ff 49 8b 04 24 a9 00 00 01 00 75 0b 49 8b 44 24 08 a8 01 75 02 <0f> 0b 49 8b 04 24 31 f6 a9 00 00 01 00 74 06 41 0f b6 74 24
5b
[1876998.350172] RSP: 0018:ffffc900000f0df0 EFLAGS: 00010246
[1876998.350177] RAX: ffffea00027f0708 RBX: ffff888008d78000 RCX: 0000000000391372
[1876998.350181] RDX: 0000000000000000 RSI: ffffe8ffffd01400 RDI: ffff888008d78000
[1876998.350185] RBP: ffff8881185a5d00 R08: ffffc90000087dd8 R09: 000000000000280a
[1876998.350189] R10: 0000000000000002 R11: 0000000000000000 R12: ffffea0000235e00
[1876998.350193] R13: ffff8881185438a0 R14: 0000000000000000 R15: ffff888118543870
[1876998.350198] FS: 0000000000000000(0000) GS:ffff88811f300000(0000) knlGS:0000000000000000
[1876998.350203] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
s#1 Part1
[1876998.350206] CR2: 00007f8dac7b09f0 CR3: 000000011e20a006 CR4: 00000000001606e0
[1876998.350210] Call Trace:
[1876998.350215] <IRQ>
[1876998.350224] ? __netif_receive_skb_core+0x70a/0x920
[1876998.350229] kfree_skb+0x32/0xb0
[1876998.350234] __netif_receive_skb_core+0x70a/0x920
[1876998.350240] __netif_receive_skb_one_core+0x36/0x80
[1876998.350245] process_backlog+0x8b/0x150
[1876998.350250] net_rx_action+0xf7/0x340
[1876998.350255] __do_softirq+0x10f/0x353
[1876998.350262] irq_exit+0xb2/0xc0
[1876998.350265] do_IRQ+0x77/0xd0
[1876998.350271] common_interrupt+0xf/0xf
[1876998.350274] </IRQ>
In order to handle such failures more graceful, this change splits the
receive loop into one for consuming the received buffers, and one for
allocating new buffers.
When GFP_ATOMIC allocations fail, the receive will continue with the
buffers that is still there, and with the expectation that the allocations
will succeed in a later call to receive.
Fixes: 92744989533c ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d07c849cd2b97d6809430dfb7e738ad31088037a upstream.
This adds error handling to the remaining dma_map_single() calls, so that
behavior is well defined if/when we run out of DMA memory.
Fixes: 92744989533c ("net: add Xilinx ll_temac device driver")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 84823ff80f7403752b59e00bb198724100dc611c upstream.
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in temac_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
This is a port of the similar fix in axienet driver,
commit 7de44285c1f6 ("net: axienet: Fix race condition causing TX hang").
Fixes: 23ecc4bde21f ("net: ll_temac: fix checksum offload logic")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
[ Upstream commit 7de44285c1f69ccfbe8be1d6a16fcd956681fee6 ]
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
xemaclite_mdio_wait():
xemaclite_readl() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which takes care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
axienet_mdio_wait_until_ready():
axienet_ior() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which take care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes following (similar) warning reported by kbuild test robot:
In function ‘memcpy’,
inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3,
inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2:
./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’:
./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’
I've replaced the offending memcpy with ether_addr_copy, because I'm
100% sure, that of_get_mac_address can't return NULL as it returns valid
pointer or ERR_PTR encoded value, nothing else.
I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this
would make the warning disappear also, but it would be confusing to
check for impossible return value just to make a compiler happy.
I'm now changing all occurencies of memcpy to ether_addr_copy after the
of_get_mac_address call, as it's very likely, that we're going to get
similar reports from kbuild test robot in the future.
Fixes: a51645f70f63 ("net: ethernet: support of_get_mac_address new ERR_PTR error")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The channel status register value can be very helpful when debugging
SDMA problems.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:66:5: warning: symbol '_temac_ior_be' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:71:6: warning: symbol '_temac_iow_be' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:76:5: warning: symbol '_temac_ior_le' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:81:6: warning: symbol '_temac_iow_le' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:648:6: warning: symbol 'ptr_to_txbd' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:654:6: warning: symbol 'ptr_from_txbd' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "pdata->mdio_bus_id" is unsigned so this condition is always true.
This patch just removes it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy_connect() function doesn't return NULL pointers. It returns
error pointers on error, so I have updated the check.
Fixes: 8425c41d1ef7 ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: d84aec42151b ("net: ll_temac: Fix support for 64-bit platforms")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As soon as TAILDESCR_PTR is written, DMA transfers might start.
Let's ensure we are ready to receive DMA IRQ's before doing that.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use usleep_range() to avoid problems with msleep() actually sleeping
much longer than expected.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we are actually using a BD for both the skb and each frag contained in
it, the oldest TX BD would be overwritten when there was exactly one BD
less than needed.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unmap the actual buffer length, not the amount of data received, avoiding
resource exhaustion of swiotlb (seen on x86_64 platform).
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With little-endian and 64-bit support in place, the ll_temac driver can
now be used on x86 and x86_64 platforms.
And while at it, enable COMPILE_TEST also.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both TEMAC and SDMA is big-endian, so make sure that all values in SDMA
buffer descriptors (cmdac_bd) are handled as big-endian, independent of the
host endianness. With all currently supported platforms being big-endian,
this change does not make a change for any of them.
Note, when using app3 and app4 for piggybacking skb pointers there is no
need to care about endianness, as neither TEMAC nor SDMA access app3 and
app4 in TX buffer descriptors.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The use of buffer descriptor APP4 field (32-bit) for storing skb pointer
obviously does not work on 64-bit platforms.
As APP3 is also unused, we can use that to store the other half of 64-bit
pointer values.
Contrary to what is hinted at in commit message of commit 15bfe05c8d63
("net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit")
there are no other pointers stored in cdmac_bd.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a side effect, a few error cases are fixed.
If of_iomap() of sdma_regs failed, no error code was returned. Fixed to
return -ENOMEM similar to of_iomap() fail of regs.
If sysfs_create_group() or register_netdev() failed, lp->phy_node was not
released.
Finally, the order in remove function is corrected to be reverse order
of what is done in probe, i.e. calling temac_mdio_teardown() last, so we
unregister the netdev that most likely is using the mdio_bus first.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This hook only implements a minimal set of ioctl hooks to be able to access
MII regs by using phytool.
When using this simple MAC controller, it's pretty difficult to do
debugging of the PHY chip without checking MII regs.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This set adds a minimal set of ethtool hooks to the driver, which provide a
decent amount of link information via ethtool.
With this change, running `ethtool ethX` in user-space provides all the
neatly-formatted information about the link (what was negotiated, what is
advertised, etc).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
If the registration fails then mdio_unregister is called.
However at unbind the unregister ia attempted again resulting
in the below crash
[ 73.544038] kernel BUG at drivers/net/phy/mdio_bus.c:415!
[ 73.549362] Internal error: Oops - BUG: 0 [#1] SMP
[ 73.554127] Modules linked in:
[ 73.557168] CPU: 0 PID: 2249 Comm: sh Not tainted 4.14.0 #183
[ 73.562895] Hardware name: xlnx,zynqmp (DT)
[ 73.567062] task: ffffffc879e41180 task.stack: ffffff800cbe0000
[ 73.572973] PC is at mdiobus_unregister+0x84/0x88
[ 73.577656] LR is at axienet_mdio_teardown+0x18/0x30
[ 73.582601] pc : [<ffffff80085fa4cc>] lr : [<ffffff8008616858>]
pstate: 20000145
[ 73.589981] sp : ffffff800cbe3c30
[ 73.593277] x29: ffffff800cbe3c30 x28: ffffffc879e41180
[ 73.598573] x27: ffffff8008a21000 x26: 0000000000000040
[ 73.603868] x25: 0000000000000124 x24: ffffffc879efe920
[ 73.609164] x23: 0000000000000060 x22: ffffffc879e02000
[ 73.614459] x21: ffffffc879e02800 x20: ffffffc87b0b8870
[ 73.619754] x19: ffffffc879e02800 x18: 000000000000025d
[ 73.625050] x17: 0000007f9a719ad0 x16: ffffff8008195bd8
[ 73.630345] x15: 0000007f9a6b3d00 x14: 0000000000000010
[ 73.635640] x13: 74656e7265687465 x12: 0000000000000030
[ 73.640935] x11: 0000000000000030 x10: 0101010101010101
[ 73.646231] x9 : 241f394f42533300 x8 : ffffffc8799f6e98
[ 73.651526] x7 : ffffffc8799f6f18 x6 : ffffffc87b0ba318
[ 73.656822] x5 : ffffffc87b0ba498 x4 : 0000000000000000
[ 73.662117] x3 : 0000000000000000 x2 : 0000000000000008
[ 73.667412] x1 : 0000000000000004 x0 : ffffffc8799f4000
[ 73.672708] Process sh (pid: 2249, stack limit = 0xffffff800cbe0000)
Fix the same by making the bus NULL on unregister.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes below checkpatch checks-
CHECK: spaces preferred around that '*' (ctx:VxV)
CHECK: No space is necessary after a cast
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes below checkpatch warnings-
WARNING: Block comments use a trailing */ on a separate line
WARNING: Block comments use * on subsequent lines
WARNING: networking block comments don't use an empty /* line,
use /* Comment
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes below kernel-doc warnings:
Function parameter or member 'maxlen' not described in 'xemaclite_recv_data'
Function parameter or member 'address'not described in 'xemaclite_set_mac_address'
Excess function parameter 'addr' description in 'xemaclite_set_mac_address'
No description found for return value of 'xemaclite_interrupt'
No description found for return value of 'xemaclite_mdio_write'
Function parameter or member 'dev' not described in 'xemaclite_mdio_setup'
Excess function parameter 'ofdev' description in 'xemaclite_mdio_setup'
No description found for return value of 'xemaclite_open'
No description found for return value of 'xemaclite_close'
Excess function parameter 'match' description in 'xemaclite_of_probe'
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove else as it is not required with if doing a return.
It also coalesce the format onto a single line and add the
missing space after the comma. Fixes below checkpatch warning-
WARNING: else is not generally useful after a break or return
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch hardcoded function name with a reference to __func__ making
the code more maintainable. Address below checkpatch warning:
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_read',
this function's name, in a string
+ "xemaclite_mdio_read(phy_id=%i, reg=%x) == %x\n",
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_write',
this function's name, in a string
+ "xemaclite_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Errors are already reported in xemaclite_mdio_setup so avoid
reporting it again.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unused 'has_mdio' flag.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 'has_mdio' flag is not used,sequence insmod->rmmod-> insmod
leads to failure as MDIO unregister doesn't happen in .remove().
Fix it by checking MII bus pointer instead.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To ensure MDIO bus is not double freed in remove() path
assign lp->mii_bus after MDIO bus registration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
axienet_open no longer return -ENODEV when PHY cannot be connected to
since commit d7cc3163e026 ("net: axienet: Support phy-less mode of operation")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 64-bit (e.g. powerpc64/allmodconfig):
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done':
drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
^
cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer.
Note that several other fields in struct cdmac_bd are also too small to
hold physical addresses on 64-bit platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|