| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 74325bf0104573c6dfce42837139aeef3f34be76 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 92696286f3bb37ba50e4bd8d1beb24afb759a799 ]
phydev->dev_flags is entirely dependent on the PHY device driver which
is going to be used, setting the internal GENET PHY revision in those
bits only makes sense when drivers/net/phy/bcm7xxx.c is the PHY driver
being used.
Fixes: 487320c54143 ("net: bcmgenet: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit efb86fede98cdc70b674692ff617b1162f642c49 ]
The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and
became 6 for GENET v4 and above, account for that difference.
Fixes: aa09677cba42 ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d397dbe606120a1ea1b11b0020c3f7a3852da5ac ]
Use the new of_get_compatible_child() helper to lookup the mdio child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
Fixes: aa09677cba42 ("net: bcmgenet: add MDIO routines")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 64bd9c8135751b561f27edaaffe93d07093f81af ]
On GENETv5, there is a hardware issue which prevents the GENET hardware
from generating a link UP interrupt when the link is operating at
10Mbits/sec. Since we do not have any way to configure the link
detection logic, fallback to polling in that case.
Fixes: 421380856d9c ("net: bcmgenet: add support for the GENETv5 hardware")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c3c397c1f16c51601a3fac4fe0c63ad8aa85a904 ]
When using the fixed PHY with GENET (e.g. MOCA) the PHY link
status can be determined from the internal link status captured
by the MAC. This allows the PHY state machine to use the correct
link state with the fixed PHY even if MAC link event interrupts
are missed when the net device is opened.
Fixes: 8d88c6ebb34c ("net: bcmgenet: enable MoCA link state change detection")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 28b45910ccda ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.
Fixes: 28b45910ccda ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcmgenet_mii_init() has an error path which is strictly identical to the
unwinding that bcmgenet_mii_exit() does, so have bcmgenet_mii_init()
utilize bcmgenet_mii_exit() for that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have fully migrated to the mdio-bcm-unimac driver, drop the
legacy MDIO bus code which did duplicate a fair amount of code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the GENET driver to register an UniMAC MDIO bus controller for
the GENET internal MDIO bus, update the platform data code to attach the
PHY to the correct MDIO bus controller.
The Device Tree portion of the code is mostly left unmodified since the
lookup/binding is done via phandles and Device Tree nodes which are much
more flexible in locating and binding PHYs to their respective MDIO bus
controllers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a6108b ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a6a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds support for the GENETv5 implementation.
The GENETv5 reports a major version of 6 instead of 5 so compensate
for this when verifying the configuration of the driver. Also the
EPHY revision is now contained in the MDIO registers of the PHY so
the EPHY revision of 0 in GENET_VER_FMT is expected for GENETv5.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Note that we're still leaking any fixed-link PHY registered in the
non-OF probe path.
Fixes: 9abf0c2b717a ("net: bcmgenet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by of_phy_find_device() when
initialising MOCA PHYs.
Fixes: 6ac9de5f6563 ("net: bcmgenet: Register link_update callback for
all MoCA PHYs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 62469c76007e ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:
PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)
This was previously fixed by commit 5dbebbb44a6a ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.
Without commit 62469c76007e we would have the following scenario after
an ifconfig down then up sequence:
- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
initialized *before* we get to initialize the UniMAC, this is
critical to ensure the PHY is in a correct state, priv->phydev is
valid, this code executes fine
- second time from bcmgenet_mii_probe(), through the normal
phy_init_hw() call (which arguably could be optimized out)
Everything is fine in that case. With commit 62469c76007e, we would have
the following scenario to happen after an ifconfig down then up
sequence:
- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
NULL
- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
bcmgenet_power_up() to initialize the internal PHY, the NULL check
becomes true, so we do not reset the PHY, yet we keep going on and
initialize the UniMAC, causing MAC activity to occur
- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
too late, the PHY is botched, and causes the above bogus pings/packets
transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By the time we execute bcmgenet_mii_probe(), the MDIO bus structure has
long been allocated and registered. Overirring the PHY interrupt using
the MDIO bus structure has no chance to work anymore, because
of_mdiobus_register() has call phy_device_create() for use, which copied
the MDIO bus address's irq for the PHY into the PHY device "irq" member.
Since we do have a proper reference to a PHY device in
bcmgenet_mii_probe(), just assign the desired IRQ value here.
Fixes: aa09677cba42 ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EPHY on GENET v1->v3 is extremely finicky, and will show occasional
failures based on the timing and reset sequence, ranging from duplicate
packets, to extremely high latencies.
Perform an additional software reset, and re-configuration to make sure it is
in a consistent and working state.
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8d88c6ebb34c ("net: bcmgenet: enable MoCA link state change
detection") added a fixed PHY link_update callback for MoCA PHYs when
registered using platform_data exclusively, this change is also
applicable to systems using Device Tree as their primary configuration
interface.
In order for this to work, move the link_update assignment into
bcmgenet_moca_phy_setup() where we know for sure that we are running on
a MoCA GENET instance, and do not override phydev->link since this is:
- properly taken care of by the PHY library by getting the link UP/DOWN
interrupts
- this now runs everytime we call bcmgenet_open(), so we need to
preserve whatever we detected before we went administratively DOWN and
then UP
- we need to make sure that MoCA PHYs start with a link DOWN during
probe in order to force a link transition to occur
To avoid a forward declaration, move bcmgenet_fixed_phy_link_update()
above its caller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have reworked the way we perform the PHY initialization, we
no longer need to differentiate between init time vs. non-init time
calls, just use a dev_info_once() print to print the PHY type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently doing a full PHY initialization and even starting the
pHY state machine during bcmgenet_mii_init() which is executed in the
driver's probe function. This is convenient to determine whether we can
attach to a proper PHY device but comes at the expense of spending up to
10ms per MDIO transactions (to reach the waitqueue timeout), which slows
things down.
This also creates a sitaution where we end-up attaching twice to the
PHY, which is not quite correct either.
Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update
its error path accordingly.
Avoid printing the message "attached PHY at address 1 [...]" every time
we bring up/down the interface and remove this print since it duplicates
what the PHY driver already does for us.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our internal GPHY might be powered off before we attempt scanning the
MDIO bus and bind a driver to it. The way we are currently determining
whether a PHY is internal or not is done *after* we have successfully
matched its driver. If the PHY is powered down, it will not respond to
the MDIO bus, so we will not be able to bind a driver to it.
Our Device Tree for GENET interfaces specifies a "phy-mode" value:
"internal" which tells if this internal uses an internal PHY or not.
If of_get_phy_mode() fails to parse the 'phy-mode' property, do an
additional manual lookup, and if we find "internal" set the
corresponding internal variable accordingly.
Replace all uses of phy_is_internal() with a check against
priv->internal_phy to avoid having to rely on whether or not
priv->phydev is set correctly.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently issuing multiple PHY resets during a suspend/resume,
first during bcmgenet_power_up() which does a hardware reset, then a
software reset by calling bcmgenet_mii_reset(). This is both unnecessary
and can take as long as 10ms per MDIO transactions while we re-apply
workarounds because we do not yet have MDIO interrupts enabled.
phy_resume() takes care of re-apply our workarounds in case we need any,
and bcmgenet_power_up() does a PHY hardware reset, all of this is more
than enough to guarantee that the PHY operates correctly.
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.
Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().
Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Ethernet PHYs/switches such as Broadcom's BCM53125 have a hardware
bug which makes them not release the MDIO line during turn-around time.
This gets flagged by the GENET MDIO controller as a read failure, and we
fail the read transaction.
Check the MDIO bus phy_ignore_ta_mask bitmask for the PHY we are reading
from and if it is listed in this bitmask, ignore the read failure and
proceed with returning the data we read out of the controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RGMII block is currently only powered on when using RGMII or
RGMII_NO_ID, which is not correct when using the GENET interface in MII
or Reverse MII modes. We always need to power on the RGMII interface for
this block to properly work, regardless of the MII mode in which we
operate.
Fixes: aa09677cba423 ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.
Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.
The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
register.
5. When the fixed PHY link status register is being read, the new
function bcmgenet_fixed_phy_link_update() gets called. It copies
the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
hardware link state.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the GPHY power down sequence by setting all power down bits, putting
the GPHY in reset, and finally cutting the 25Mhz reference clock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were missing a number of extra steps and delays to power-up the GPHY, update
the sequence to reflect the proper procedure here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for implementing the power down GPHY sequence, rename
bcmgenet_ephy_power_up to illustrate that it is not EPHY specific but
PHY agnostic, and add an "enable" argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify bcmgenet driver so that it can be used on Broadcom 7xxx
MIPS-based STB platforms without a device tree.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes: b6e978e50444 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793fa4 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes: b6e978e50444 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcmgenet_mii_setup() is called from the PHY state machine every 1-2 seconds
when the PHYs are in PHY_POLL mode.
Improve bcmgenet_mii_setup() so that it touches the MAC registers only when
the link is up and there was a change to link, speed, duplex, or pause status.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The integrated BCM7xxx PHY contains no useful revision information in
its MII_PHYSID2 bits 3:0, that information is instead contained in the
GENET hardware block.
We already read the GENET 32-bit revision register, so store the
integrated PHY revision in the driver private structure, and then
communicate this revision value to the PHY driver by overriding the
phy_flags value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have removed the need for the PHY_BRCM_100MBPS_WAR flag, we
can remove it from the GENET driver and the broadcom shared header file.
The PHY driver checks the PHY supported bitmask instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we bring the interface down, phy_stop() will schedule the PHY state
machine to call our link adjustment callback. By the time we do so, we
may have clock gated off the GENET hardware block, and this will cause
bus errors to happen in bcmgenet_mii_setup():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
Fixes: 240524089d7a ("net: bcmgenet: only update UMAC_CMD if something changed")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the fixed phy setup make sure to not overwrite a valid value of
phy_dn (that is holding a reference to a phy-handle) and also acquire a
reference to the MAC node to consistently return with the phy_dn pointer
holding a reference.
Also add the corresponding of_node_put in the error path and the remove
function.
Fixes: 9abf0c2b717a ("net: bcmgenet: use the new fixed PHY helpers")
Fixes: aa09677cba42 ("net: bcmgenet: add MDIO routines")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were two places that used kzalloc() with a multiplied sizeof(),
replace these with kcalloc as recommended by checkpatch.pl.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
checkpatch.pl flagged a lot of "CHECK: Alignment should match open
parenthesis" checks, fix all of them to make the driver neater. While
at it fix some obvious typos and re-arrange some of the lines to avoid
going over 80 columns.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a smaller GPLv2 header and remove all the boilerplate code as well
as the FSF mail address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Yang Yingliang
Florian Fainelli
Johan Hovold
Doug Berger
David S. Miller
Philippe Reynes
Andrew Lunn
Petri Gynther
Uwe Kleine-König