| Age | Commit message (Collapse) | Author |
|---|
|
The backport of commit afeaade90db4 "media: em28xx: make
v4l2-compliance happier by starting sequence on zero" added a
reset on em28xx_v4l2::field_count to em28xx_enable_analog_tuner()
but it should be done in em28xx_start_analog_streaming().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 910b0797fa9e8af09c44a3fa36cb310ba7a7218d ]
Fix bug by moving the i2c_unregister_device calls after deregistration
of dvb frontend.
The new style i2c drivers already destroys the frontend object at
i2c_unregister_device time.
When the dvb frontend is unregistered afterwards it leads to this oops:
[ 6058.866459] BUG: unable to handle kernel NULL pointer dereference at 00000000000001f8
[ 6058.866578] IP: dvb_frontend_stop+0x30/0xd0 [dvb_core]
[ 6058.866644] PGD 0
[ 6058.866646] P4D 0
[ 6058.866726] Oops: 0000 [#1] SMP
[ 6058.866768] Modules linked in: rc_pinnacle_pctv_hd(O) em28xx_rc(O) si2157(O) si2168(O) em28xx_dvb(O) em28xx(O) si2165(O) a8293(O) tda10071(O) tea5767(O) tuner(O) cx23885(O) tda18271(O) videobuf2_dvb(O) videobuf2_dma_sg(O) m88ds3103(O) tveeprom(O) cx2341x(O) v4l2_common(O) dvb_core(O) rc_core(O) videobuf2_memops(O) videobuf2_v4l2(O) videobuf2_core(O) videodev(O) media(O) bluetooth ecdh_generic ums_realtek uas rtl8192cu rtl_usb rtl8192c_common rtlwifi usb_storage snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic i2c_mux snd_hda_intel snd_hda_codec snd_hwdep x86_pkg_temp_thermal snd_hda_core kvm_intel kvm irqbypass [last unloaded: videobuf2_memops]
[ 6058.867497] CPU: 2 PID: 7349 Comm: kworker/2:0 Tainted: G W O 4.13.9-gentoo #1
[ 6058.867595] Hardware name: MEDION E2050 2391/H81H3-EM2, BIOS H81EM2W08.308 08/25/2014
[ 6058.867692] Workqueue: usb_hub_wq hub_event
[ 6058.867746] task: ffff88011a15e040 task.stack: ffffc90003074000
[ 6058.867825] RIP: 0010:dvb_frontend_stop+0x30/0xd0 [dvb_core]
[ 6058.867896] RSP: 0018:ffffc90003077b58 EFLAGS: 00010293
[ 6058.867964] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000010040001f
[ 6058.868056] RDX: ffff88011a15e040 RSI: ffffea000464e400 RDI: ffff88001cbe3028
[ 6058.868150] RBP: ffffc90003077b68 R08: ffff880119390380 R09: 000000010040001f
[ 6058.868241] R10: ffffc90003077b18 R11: 000000000001e200 R12: ffff88001cbe3028
[ 6058.868330] R13: ffff88001cbe68d0 R14: ffff8800cf734000 R15: ffff8800cf734098
[ 6058.868419] FS: 0000000000000000(0000) GS:ffff88011fb00000(0000) knlGS:0000000000000000
[ 6058.868511] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6058.868578] CR2: 00000000000001f8 CR3: 00000001113c5000 CR4: 00000000001406e0
[ 6058.868662] Call Trace:
[ 6058.868705] dvb_unregister_frontend+0x2a/0x80 [dvb_core]
[ 6058.868774] em28xx_dvb_fini+0x132/0x220 [em28xx_dvb]
[ 6058.868840] em28xx_close_extension+0x34/0x90 [em28xx]
[ 6058.868902] em28xx_usb_disconnect+0x4e/0x70 [em28xx]
[ 6058.868968] usb_unbind_interface+0x6d/0x260
[ 6058.869025] device_release_driver_internal+0x150/0x210
[ 6058.869094] device_release_driver+0xd/0x10
[ 6058.869150] bus_remove_device+0xe4/0x160
[ 6058.869204] device_del+0x1ce/0x2f0
[ 6058.869253] usb_disable_device+0x99/0x270
[ 6058.869306] usb_disconnect+0x8d/0x260
[ 6058.869359] hub_event+0x93d/0x1520
[ 6058.869408] ? dequeue_task_fair+0xae5/0xd20
[ 6058.869467] process_one_work+0x1d9/0x3e0
[ 6058.869522] worker_thread+0x43/0x3e0
[ 6058.869576] kthread+0x104/0x140
[ 6058.869602] ? trace_event_raw_event_workqueue_work+0x80/0x80
[ 6058.869640] ? kthread_create_on_node+0x40/0x40
[ 6058.869673] ret_from_fork+0x22/0x30
[ 6058.869698] Code: 54 49 89 fc 53 48 8b 9f 18 03 00 00 0f 1f 44 00 00 41 83 bc 24 04 05 00 00 02 74 0c 41 c7 84 24 04 05 00 00 01 00 00 00 0f ae f0 <48> 8b bb f8 01 00 00 48 85 ff 74 5c e8 df 40 f0 e0 48 8b 93 f8
[ 6058.869850] RIP: dvb_frontend_stop+0x30/0xd0 [dvb_core] RSP: ffffc90003077b58
[ 6058.869894] CR2: 00000000000001f8
[ 6058.875880] ---[ end trace 717eecf7193b3fc6 ]---
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit afeaade90db4c5dab93f326d9582be1d5954a198 upstream.
The v4l2-compliance tool complains if a video doesn't start
with a zero sequence number.
While this shouldn't cause any real problem for apps, let's
make it happier, in order to better check the v4l2-compliance
differences before and after patchsets.
This is actually an old issue. It is there since at least its
videobuf2 conversion, e. g. changeset 3829fadc461 ("[media]
em28xx: convert to videobuf2"), if VB1 wouldn't suffer from
the same issue.
Cc: stable@vger.kernel.org
Fixes: d3829fadc461 ("[media] em28xx: convert to videobuf2")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15644bfa195bd166d0a5ed76ae2d587f719c3dac upstream.
Instead of using a register value, use an AMUX name, as otherwise
VIDIOC_G_AUDIO would fail.
Cc: stable@vger.kernel.org
Fixes: 766ed64de554 ("V4L/DVB (11827): Add support for Terratec Grabster AV350")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f823ce2a1202d47110a7ef86b65839f0be8adc38 upstream.
Follow the V4L2 spec, as warned by v4l2-compliance:
warn: v4l2-test-formats.cpp(732): TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(733): This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(734): http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
Cc: stable@vger.kernel.org
Fixes: bddcf63313c6 ("V4L/DVB (9927): em28xx: use a more standard way to specify video formats")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f2a326c928cca1f5e36a3dceaf66e8c6b34e9cb8 ]
Add additional pids to driver list
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c7c7e8d7803406daa21e96d00c357de8b77b6764 ]
Hauppauge em28xx bulk devices exhibit continuity errors and corrupted
packets, when run in VMWare virtual machines. Unknown if other
manufacturers bulk models exhibit the same issue. KVM/Qemu is unaffected.
According to documentation the maximum packet multiplier for em28xx in bulk
transfer mode is 256 * 188 bytes. This changes the size of bulk transfers
to maximum supported value and have a bonus beneficial alignment.
Before:
After:
This sets up USB to expect just as many bytes as the em28xx is set to emit.
Successful usage under load afterwards natively and in both VMWare
and KVM/Qemu virtual machines.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The calculation of the left volume looks suspect, the value of
0x1f - ((val << 8) & 0x1f) is always 0x1f. The debug prior to the
assignment of value[1] prints the left volume setting using the
calculation 0x1f - (val >> 8) & 0x1f which looks correct to me.
Fix the left volume by using the correct expression as used in
the debug.
Detected by CoverityScan, CID#146140 ("Wrong operator used")
Fixes: 850d24a5a861 ("[media] em28xx-alsa: add mixer support for AC97 volume controls")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Make these const as they are only used in a copy operation.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
While committing a change on em28xx, I got a warning of a
typo there. So, fix it on em28xx and on two other media drivers
with the same typo.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There's a new version of Terratec H6 with uses USB ID
0ccd:10b2. This version is similar to the old one (with is
supported via the HTC entry), except that this one has the
eeprom on the second bus.
On this board, one side of this board is labeled with:
dvbc v2.0
The other side with:
94V-0, MO2, RK-4221 with huge digits: 1107
With those patches, the board is properly detected:
em28xx 1-1.5:1.0: New device TERRATEC TERRATCE H5 MKII @ 480 Mbps (0ccd:10b2, interface 0, class 0)
em28xx 1-1.5:1.0: Audio interface 0 found (Vendor Class)
em28xx 1-1.5:1.0: Video interface 0 found: isoc
em28xx 1-1.5:1.0: DVB interface 0 found: isoc
em28xx 1-1.5:1.0: chip ID is em2884
em28xx eeprom 00000000: 26 00 00 00 02 0b 0f e5 f5 64 01 60 09 e5 f5 64 &........d.`...d
em28xx eeprom 00000010: 09 60 03 c2 c6 22 e5 f7 b4 03 13 e5 f6 b4 87 03 .`..."..........
em28xx eeprom 00000020: 02 0a b9 e5 f6 b4 93 03 02 09 46 c2 c6 22 c2 c6 ..........F.."..
em28xx eeprom 00000030: 22 00 60 00 ef 70 08 85 3d 82 85 3c 83 93 ff ef ".`..p..=..<....
em28xx eeprom 00000040: 60 19 85 3d 82 85 3c 83 e4 93 12 07 a3 12 0a fe `..=..<.........
em28xx eeprom 00000050: 05 3d e5 3d 70 02 05 3c 1f 80 e4 22 12 0b 06 02 .=.=p..<..."....
em28xx eeprom 00000060: 07 e2 01 00 1a eb 67 95 cd 0c b2 10 f0 13 6b 03 ......g.......k.
em28xx eeprom 00000070: 98 22 6a 1c 86 12 27 57 4e 16 29 00 60 00 00 00 ."j...'WN.).`...
em28xx eeprom 00000080: 02 00 00 00 5e 00 13 00 f0 10 44 82 82 00 00 00 ....^.....D.....
em28xx eeprom 00000090: 5b 81 c0 00 00 00 20 40 20 80 02 20 10 01 00 00 [..... @ .. ....
em28xx eeprom 000000a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
em28xx eeprom 000000b0: c6 40 00 00 81 00 00 00 00 00 00 00 00 c4 00 00 .@..............
em28xx eeprom 000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1c 03 ................
em28xx eeprom 000000d0: 31 00 32 00 33 00 34 00 35 00 36 00 37 00 38 00 1.2.3.4.5.6.7.8.
em28xx eeprom 000000e0: 39 00 41 00 42 00 43 00 44 00 12 03 54 00 45 00 9.A.B.C.D...T.E.
em28xx eeprom 000000f0: 52 00 52 00 41 00 54 00 45 00 43 00 22 03 54 00 R.R.A.T.E.C.".T.
em28xx 1-1.5:1.0: eeprom 000100: ... (skipped)
em28xx 1-1.5:1.0: EEPROM ID = 26 00 00 00, EEPROM hash = 0xbcd5a8cf
em28xx 1-1.5:1.0: EEPROM info:
em28xx 1-1.5:1.0: microcode start address = 0x0004, boot configuration = 0x00
em28xx 1-1.5:1.0: I2S audio, 5 sample rates
em28xx 1-1.5:1.0: 500mA max power
em28xx 1-1.5:1.0: Table at offset 0x27, strings=0x2298, 0x1c6a, 0x1286
em28xx 1-1.5:1.0: Identified as Terratec Cinergy H6 rev. 2 (card=101)
em28xx 1-1.5:1.0: Currently, V4L2 is not supported on this model
em28xx 1-1.5:1.0: dvb set to isoc mode.
usbcore: registered new interface driver em28xx
em28xx 1-1.5:1.0: Binding audio extension
em28xx 1-1.5:1.0: em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
em28xx 1-1.5:1.0: em28xx-audio.c: Copyright (C) 2007-2016 Mauro Carvalho Chehab
em28xx 1-1.5:1.0: Endpoint 0x83 high-speed on intf 0 alt 7 interval = 8, size 196
em28xx 1-1.5:1.0: Number of URBs: 1, with 64 packets and 192 size
em28xx 1-1.5:1.0: Audio extension successfully initialized
em28xx: Registered (Em28xx Audio Extension) extension
em28xx 1-1.5:1.0: Binding DVB extension
drxk: status = 0x639260d9
drxk: detected a drx-3926k, spin A3, xtal 20.250 MHz
drxk: DRXK driver version 0.9.4300
drxk: frontend initialized.
tda18271 4-0060: creating new instance
tda18271: TDA18271HD/C2 detected @ 4-0060
dvbdev: DVB: registering new adapter (1-1.5:1.0)
em28xx 1-1.5:1.0: DVB: registering adapter 0 frontend 0 (DRXK DVB-C DVB-T)...
dvbdev: dvb_create_media_entity: media entity 'DRXK DVB-C DVB-T' registered.
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
em28xx 1-1.5:1.0: DVB extension successfully initialized
em28xx: Registered (Em28xx dvb Extension) extension
em28xx 1-1.5:1.0: Registering input extension
rc rc0: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0
Registered IR keymap rc-nec-terratec-cinergy-xs
input: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0/input0
em28xx 1-1.5:1.0: Input extension successfully initalized
em28xx: Registered (Em28xx Input Extension) extension
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
While testing support for Terratec H6 rev. 2, it was noticed
that reading from eeprom there causes a timeout error.
Apparently, this is due to the need of properly setting GPIOs.
In any case, the driver doesn't really require eeprom reading
to succeed, as this is currently used only for debug.
So, Ignore such errors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
- avoid duplicate debugging messages in em28xx_read_reg_req_len()
- do not describe successful usb transfers in em28xx_read_reg_len()
as "failed"
- report errors in em28xx_write_regs_req(), too
- print the usb error numbers, too
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Adding support for SRGGB8 is as simple as adding a new entry at
struct em28xx_fmt.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
CbYCrY has been identified by looking into the tvp5150 driver and the
saa7115 datasheet.
YUV formats have been verified with em2765 + ov2640 (VAD Laplace webcam).
RGB8 formats have been verified with em2710/em2820 + mt9v011 (Silvercrest
webcam 1.3mpix).
I also did some cross-checking with these two camera devices and 0x08-0x0b
are at least 16 bits per pixel formats on em2710/em2820, too, and
0x0c-0x0f are at least 8 bits per pixel formats on em2765, too.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
With an unknown sensor, norm_maxw() and norm_maxh() return 0 as max.
height and width values, which causes a devide by zero in size_to_scale().
Of course we could use speculative default values for unknown sensors,
but the chance that the device works at this resolution without any
driver/setup is very low and therefore not worth the efforts.
Instead, just don't treat the device as camera.
A message will then be printed to the log that the device isn't supported.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
With MEDIA_SUBDRV_AUTOSELECT enabled in the kernel config, the em28xx
driver currently does't select some used subdrivers.
Fix this by adding the missing auto-selections to the Kconfig file.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The v4l2 dummy clock has been added with commit fc5d0f8a8878
("V4L2: em28xx: register a V4L2 clock source") to be able to use the ov2640
soc_camera driver.
Since commit 46796cfcd346 ("ov2640: use standard clk and enable it") it is
no longer required.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use i2c_smbus_read_word_data() instead of i2c_master_send() and
i2c_master_recv() for reading the ID of Micorn sensors.
i2c_smbus_read_word_data() assumes that byes are in little-endian,
so, it uses:
data->word = msgbuf1[0] | (msgbuf1[1] << 8);
However, Micron datasheet describes the ID as if they were read
in big-endian. So, we need to change the byte order in order to
match the ID number as described on their datasheets.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add new usbid eb1a:5051 for the Ion Video 2 PC MKII, Startech svid2usb23
and Raygo R12-41373.
Signed-off-by: Alexandre-Xavier Labonté-Lamoureux <alexandrexavier@live.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The em28xx driver still used the soc_camera.h header for the ov2640
driver. Since this driver no longer uses soc_camera, that include can
be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
It's no longer necessary to keep the i2c_client in the device struct
unmodified until a sensor is found, so reduce stack usage in
em28xx_probe_sensor_micron() and em28xx_probe_sensor_omnivision() by using
a pointer to the client instead of a local copy.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
tveeprom_hauppauge_analog() used to need the I2C adapter in
order to print debug messages. As it now uses pr_foo() facilities
since commit 6037b3ca28f4 ("[media] tveeprom: print log messages
using pr_foo()"), the first argument of the function is not
needed anymore.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Hauppauge WinTV-dualHD model 01595 is a USB 2.0 dual ATSC/QAM tuner with
the following components:
USB bridge: Empia em28274
Demodulator: 2x LG LGDT3306a at addresses 0xb2 and 0x1c
Tuner: 2x Silicon Labs si2157 at addresses 0xc0 and 0xc4
This patch enables only the first tuner.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Report the correct NEC variant.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Drop the FSF's postal address from the source code files that typically
contain mostly the license text. Of the 628 removed instances, 578 are
outdated.
The patch has been created with the following command without manual edits:
git grep -l "675 Mass Ave\|59 Temple Place\|51 Franklin St" -- \
drivers/media/ include/media|while read i; do i=$i perl -e '
open(F,"< $ENV{i}");
$a=join("", <F>);
$a =~ s/[ \t]*\*\n.*You should.*\n.*along with.*\n.*(\n.*USA.*$)?\n//m
&& $a =~ s/(^.*)Or, (point your browser to) /$1To obtain the license, $2\n$1/m;
close(F);
open(F, "> $ENV{i}");
print F $a;
close(F);'; done
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Now that we're storing usb_interface at em28xx struct,
there's no good reason to keep storing usb_device, as we can
get it from usb_interface. So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The usb_device->dev is not the right device for dev_foo() calls.
Instead, it should use usb_interface->dev.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Changing the device name, causes it to be unable to remove the
sysfs file, causing troubles if a device is removed and then
re-inserted.
[ 1010.310320] WARNING: CPU: 3 PID: 119 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x7b/0x90
[ 1010.310323] sysfs: cannot create duplicate filename '/bus/usb/devices/1-3.3'
[ 1010.310325] Modules linked in: lgdt330x em28xx_dvb dvb_core em28xx_alsa tuner_xc2028 tuner tvp5150 em28xx_v4l videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_core em28xx tveeprom v4l2_common videodev media xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter ip_tables x_tables cmac bnep cpufreq_powersave cpufreq_conservative cpufreq_userspace binfmt_misc parport_pc ppdev lp parport snd_hda_codec_hdmi iTCO_wdt snd_hda_codec_realtek iTCO_vendor_support snd_hda_codec_generic arc4 intel_rapl x86_pkg_temp_thermal iwlmvm intel_powerclamp coretemp kvm_intel mac80211 kvm i915
[ 1010.310383] irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel iwlwifi pl2303 aesni_intel btusb aes_x86_64 usbserial lrw btrtl gf128mul glue_helper btbcm ablk_helper cryptd btintel bluetooth drm_kms_helper cfg80211 drm psmouse pcspkr i2c_i801 e1000e serio_raw snd_hda_intel snd_soc_rt5640 snd_hda_codec snd_soc_rl6231 snd_soc_ssm4567 mei_me i2c_smbus rfkill snd_hda_core ptp mei snd_soc_core ehci_pci sg lpc_ich shpchp mfd_core ehci_hcd pps_core snd_hwdep i2c_algo_bit snd_compress snd_pcm sdhci_acpi snd_timer battery snd sdhci elan_i2c snd_soc_sst_acpi mmc_core fjes dw_dmac i2c_hid soundcore snd_soc_sst_match i2c_designware_platform video i2c_designware_core acpi_pad acpi_als kfifo_buf tpm_tis button industrialio tpm_tis_core tpm ext4 crc16 jbd2 fscrypto mbcache dm_mod joydev evdev hid_logitech_hidpp
[ 1010.310449] sd_mod hid_logitech_dj usbhid hid ahci libahci crc32c_intel libata xhci_pci xhci_hcd scsi_mod usbcore fan thermal
[ 1010.310464] CPU: 3 PID: 119 Comm: kworker/3:2 Not tainted 4.9.0-rc8+ #14
[ 1010.310466] Hardware name: /NUC5i7RYB, BIOS RYBDWi35.86A.0350.2015.0812.1722 08/12/2015
[ 1010.310487] Workqueue: usb_hub_wq hub_event [usbcore]
[ 1010.310490] 0000000000000000 ffffffff848f56c5 ffff8803b1f7f858 0000000000000000
[ 1010.310496] ffffffff8414f8f8 ffff88030000001f ffffed00763eff07 ffff8803b1f7f8f0
[ 1010.310501] ffff8803b3ea1e60 0000000000000001 ffffffffffffffef ffff8803b45c6840
[ 1010.310505] Call Trace:
[ 1010.310517] [<ffffffff848f56c5>] ? dump_stack+0x5c/0x77
[ 1010.310522] [<ffffffff8414f8f8>] ? __warn+0x168/0x1a0
[ 1010.310526] [<ffffffff8414f9e4>] ? warn_slowpath_fmt+0xb4/0xf0
[ 1010.310529] [<ffffffff8414f930>] ? __warn+0x1a0/0x1a0
[ 1010.310534] [<ffffffff845436c6>] ? kasan_kmalloc+0xa6/0xd0
[ 1010.310539] [<ffffffff846ec2fa>] ? kernfs_path_from_node+0x4a/0x60
[ 1010.310543] [<ffffffff846f66eb>] ? sysfs_warn_dup+0x7b/0x90
[ 1010.310547] [<ffffffff846f6f26>] ? sysfs_do_create_link_sd.isra.2+0xb6/0xd0
[ 1010.310553] [<ffffffff84cd5a08>] ? bus_add_device+0x318/0x6b0
[ 1010.310557] [<ffffffff846f8693>] ? sysfs_create_groups+0x83/0x110
[ 1010.310562] [<ffffffff84ccff87>] ? device_add+0x777/0x1350
[ 1010.310567] [<ffffffff84ccf810>] ? device_private_init+0x180/0x180
[ 1010.310583] [<ffffffffc00c0f77>] ? usb_new_device+0x707/0x1030 [usbcore]
[ 1010.310598] [<ffffffffc00c58c5>] ? hub_event+0x1d65/0x3280 [usbcore]
[ 1010.310604] [<ffffffff841eb4ab>] ? account_entity_dequeue+0x30b/0x4a0
[ 1010.310618] [<ffffffffc00c3b60>] ? hub_port_debounce+0x280/0x280 [usbcore]
[ 1010.310624] [<ffffffff8407ccd0>] ? compat_start_thread+0x80/0x80
[ 1010.310629] [<ffffffff851f5cb4>] ? __schedule+0x704/0x1770
[ 1010.310633] [<ffffffff851f55b0>] ? io_schedule_timeout+0x390/0x390
[ 1010.310638] [<ffffffff84541783>] ? cache_reap+0x173/0x200
[ 1010.310642] [<ffffffff84197bed>] ? process_one_work+0x4ed/0xe60
[ 1010.310646] [<ffffffff84198642>] ? worker_thread+0xe2/0xfd0
[ 1010.310650] [<ffffffff8421f76c>] ? __wake_up_common+0xbc/0x160
[ 1010.310654] [<ffffffff84198560>] ? process_one_work+0xe60/0xe60
[ 1010.310658] [<ffffffff841a837c>] ? kthread+0x1cc/0x220
[ 1010.310663] [<ffffffff841a81b0>] ? kthread_park+0x80/0x80
[ 1010.310667] [<ffffffff841a81b0>] ? kthread_park+0x80/0x80
[ 1010.310671] [<ffffffff841a81b0>] ? kthread_park+0x80/0x80
[ 1010.310675] [<ffffffff852016f5>] ? ret_from_fork+0x25/0x30
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
In randconfig builds that select VIDEO_EM28XX_V4L2 and
MEDIA_SUBDRV_AUTOSELECT, but not MEDIA_CAMERA_SUPPORT, we get
a Kconfig warning:
warning: (VIDEO_EM28XX_V4L2) selects VIDEO_MT9V011 which has unmet direct dependencies (MEDIA_SUPPORT && I2C && VIDEO_V4L2 && MEDIA_CAMERA_SUPPORT)
This avoids the warning by making that 'select' conditional on
MEDIA_CAMERA_SUPPORT. Alternatively we could mark EM28XX as
'depends on MEDIA_CAMERA_SUPPORT', but it does not seem to
have any real dependency on that itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Instead of using v4l_foo(), use the dev_foo() macros, as
most modern media drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Instead of using pr_foo(), use dev_foo(), with provides a
better output. As this device is a multi-interface one,
we'll set the device name to show the chipset and the driver
used.
While here, get rid of printk continuation messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There are still several places with printk's called directly.
Convert them to pr_foo() macros, except for the debug printk's,
as those are enabled via modprobe vars.
While here, realign the pr_foo() arguments to match the
recommended CodingStyle.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There's no reason to keep using em28xx-specific printk macros
here. Just use pr_foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This driver has a lot of printk continuation lines for
debugging purposes. Since commit 563873318d32
("Merge branch 'printk-cleanups"), this won't work as expected
anymore. So, let's add KERN_CONT to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Due to the 80-cols checkpatch warnings, several strings
were broken into multiple lines. This is not considered
a good practice anymore, as it makes harder to grep for
strings at the source code. So, join those continuation
lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
These i2c_algorithm structures are only stored in the alg field of an
i2c_adapter structure, which is declared as const. This declare the
structures as const as well.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.alg = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for snd_pcm_ops structures that are only stored in the ops field of a
snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
urb fails
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
urb fails
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Gcc 6.1 warns about an unused table:
drivers/media/usb/em28xx/em28xx-dvb.c:907:38: warning: 'pctv_461e_m88ds3103_config' defined but not used [-Wunused-const-variable=]
static const struct m88ds3103_config pctv_461e_m88ds3103_config = {
^~~~~~~~~~~~~~~~~~~~~~~~~~
That's a left over of patch 76b91be3d360a ('em28xx: PCTV 461e use I2C
client for demod and SEC').
Remove the dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
Ben Hutchings
Matthias Schwarzott
Mauro Carvalho Chehab
Brad Love
Greg Kroah-Hartman
Colin Ian King
Bhumika Goyal
Sean Young
Mauro Carvalho Chehab
Frank Schaefer
Alexandre-Xavier Labonté-Lamoureux
Hans Verkuil
Kevin Cheng
Andi Shyti
Sakari Ailus
Mauro Carvalho Chehab
Arnd Bergmann
Julia Lawall
Wolfram Sang