| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 193c2a07cfaacb9249ab0e3d34bce32490879355 ]
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 36f5d9ef26e52edff046b4b097855db89bf0cd4a ]
The driver only registers one input device, which uses the screen
parameters from the first T9 instance. The first T63 instance also uses
those parameters.
It is incorrect to send input reports from the second instances of these
objects if they are enabled: the input scaling will be wrong and the
positions will be mashed together.
This also causes problems on Android if the number of slots exceeds 32.
In the future, this could be handled by looking for enabled touch object
instances and creating an input device for each one.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 068bdb67ef74df0ad1627b7247a163e3e252ac11 ]
The automatic update mechanism will trigger an update if the
info block CRCs are different between maxtouch configuration
file (maxtouch.cfg) and chip.
The driver compared the CRCs without retrieving the chip CRC,
resulting always in a failure and firmware flashing action
triggered. Fix this issue by retrieving the chip info block
CRC before the check.
Note that this solution has the benefit that by reading the
information block and the object table into a contiguous region
of memory, we can verify the checksum at probe time. This means
we make sure that we are indeed talking to a chip that supports
object protocol correctly.
Using this patch on a kevin chromebook, the touchscreen and
touchpad drivers are able to match the CRC:
atmel_mxt_ts 3-004b: Family: 164 Variant: 14 Firmware V2.3.AA Objects: 40
atmel_mxt_ts 5-004a: Family: 164 Variant: 17 Firmware V2.0.AA Objects: 31
atmel_mxt_ts 3-004b: Resetting device
atmel_mxt_ts 5-004a: Resetting device
atmel_mxt_ts 3-004b: Config CRC 0x573E89: OK
atmel_mxt_ts 3-004b: Touchscreen size X4095Y2729
input: Atmel maXTouch Touchscreen as /devices/platform/ff130000.i2c/i2c-3/3-004b/input/input5
atmel_mxt_ts 5-004a: Config CRC 0x0AF6BA: OK
atmel_mxt_ts 5-004a: Touchscreen size X1920Y1080
input: Atmel maXTouch Touchpad as /devices/platform/ff140000.i2c/i2c-5/5-004a/input/input6
Signed-off-by: Nick Dyer <nick.dyer@shmanahar.org>
Acked-by: Benson Leung <bleung@chromium.org>
[Ezequiel: minor patch massage]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ca4d1ae9bad0f59bd6f851c39b19f5366953666 upstream.
GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp
Tested on a unit from the first production run sent to Indiegogo backers
Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f372b81101e6895252298e563d634d5e44ae81e7 upstream.
This patch adds the correct platform data information for the Caroline
Chromebook, so that the mouse button does not get stuck in pressed state
after the first click.
The Samus button keymap and platform data definition are the correct
ones for Caroline, so they have been reused here.
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Tested-by: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
[dtor: adjusted vendor spelling to match shipping firmware]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cba04cdf437d745fac85220d1d692a9ae23d7004 ]
The interrupt is requested before the device is powered on and
it's value in some cases cannot be reliable. It happens on some
devices that an interrupt is generated as soon as requested
before having the chance to disable the irq.
Set the irq flag as IRQ_NOAUTOEN before requesting it.
This patch mutes the error:
stmfts 2-0049: failed to read events: -11
received sometimes during boot time.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit faec44b6838312484d63e82286087cf2d5ebb891 ]
We should not try to do any i2c transfers before the controller is
resumed (which happens before our resume method gets called).
So we need to disable our IRQ while suspended to enforce this. The
code paths for devices with GPIOs for the int and reset pins already
disable the IRQ the through goodix_free_irq().
This commit also disables the IRQ while suspended for devices without
GPIOs for the int and reset pins.
This fixes the i2c bus sometimes getting stuck after a suspend/resume
causing the touchscreen to sometimes not work after a suspend/resume.
This has been tested on a GPD pocked device.
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://www.reddit.com/r/GPDPocket/comments/7niut2/fix_for_broken_touch_after_resume_all_linux/
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 906bf7daa0618d0ef39f4872ca42218c29a3631f upstream.
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
To make things worse, the parent node was prematurely freed, while the
child node was leaked.
Fixes: 2e57d56747e6 ("mfd: 88pm860x: Device tree support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
- a new ACPI ID for Elan touchpad found in yet another Ideapad model
- Synaptics RMI4 will allow binding to controllers reporting SMB
version 3 (note that we are not adding any new ACPI IDs to the
Synaptics PS/2 drover so unless user explicitly enables intertouch
support there is no user-visible change)
- a fixup to TSC 2004/5 touchscreen driver to mark input devices as
"direct" to help userspace identify the type of device they are
dealing with
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - RMI4 can also use SMBUS version 3
Input: tsc200x-core - set INPUT_PROP_DIRECT
Input: elan_i2c - add ELAN060C to the ACPI table
|
|
If INPUT_PROP_DIRECT is set, userspace doesn't have to fall back to old
ways of identifying touchscreen devices.
In order to identify a touchscreen device, Android for example, seems to
already depend on INPUT_PROP_DIRECT to be present in drivers. udev still
checks for either BTN_TOUCH or INPUT_PROP_DIRECT. Checking for BTN_TOUCH
however can quite easily lead to false positives; it's a code that not only
touchscreen device drivers use.
According to the documentation, touchscreen drivers should have this
property set and in order to make life easy for userspace, let's set it.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a couple of fixups to the sparse-keymap module and the Microchip
AR1021 touchscreen driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sparse-keymap - send sync event for KE_SW/KE_VSW
Input: ar1021_i2c - set INPUT_PROP_DIRECT
|
|
If INPUT_PROP_DIRECT is set, userspace doesn't have to fall back to old
ways of identifying touchscreen devices. Let's add it.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- joydev now implements a blacklist to avoid creating joystick nodes
for accelerometers found in composite devices such as PlaStation
controllers
- assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-psu - check if CDC union descriptor is sane
Input: joydev - blacklist ds3/ds4/udraw motion sensors
Input: allow matching device IDs on property bits
Input: factor out and export input_device_id matching code
Input: goodix - poll the 'buffer status' bit before reading data
Input: axp20x-pek - fix module not auto-loading for axp221 pek
Input: tca8418 - enable interrupt after it has been requested
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Input: synaptics - disable kernel tracking on SMBus devices
|
|
The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.
Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.
This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only
if necessary").
Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.
Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
add comment about typical poll time]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The commit 78bcac7b2ae1e ("Input: add support for the STMicroelectronics
FingerTip touchscreen) used the 'touchscreen_parse_properties()' helper
function in order to get the value of common properties.
But, commit 78bcac7b2ae1e didn't set the capability of ABS_MT_POSITION_*
before calling touchscreen_parse_properties(). In result, the max_x and
max_y of 'struct touchscreen_properties' were not set.
Fixes: 78bcac7b2ae1e ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Cc: stable@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Step config setting for 5 wire touchscreen is incorrect for Y coordinates.
It was broken while we moved to DT. If you look close at the offending
commit bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made
configurable"), the change was:
- STEPCONFIG_XNP | STEPCONFIG_YPN;
+ ts_dev->bit_xn | ts_dev->bit_yp;
while bit_xn = STEPCONFIG_XNN and bit_yp = STEPCONFIG_YNN. Not quite the
same.
Fixes: bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[vigneshr@ti.com: Rebase to v4.14-rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"A second round of updates for the input subsystem:
- a new driver for PWM-controlled vibrators
- ucb1400 touchscreen driver had completely busted suspend/resume
handling
- we now handle "home" button found on some devices with Goodix
touchscreens
- assorted other fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Gigabyte P57 to the keyboard reset table
Input: xpad - validate USB endpoint type during probe
Input: ucb1400_ts - fix suspend and resume handling
Input: edt-ft5x06 - fix access to non-existing register
Input: elantech - make arrays debounce_packet static, reduces object code size
Input: surface3_spi - make const array header static, reduces object code size
Input: goodix - add support for capacitive home button
Input: add a driver for PWM controllable vibrators
Input: adi - make array seq static, reduces object code size
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
Instead of stopping the touchscreen we were starting it in suspend, and
disabling it in resume.
Fixes: c899afedf168 ("Input: ucb1400_ts - convert to threaded IRQ")
Reported-by: Anton Volkov <avolkov@ispras.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
reg_addr->reg_report_rate is supposed to exist in M06, not M09.
The driver is written to skip avoids access to non-existing registers
when the register address is NO_REGISTER (0xff). But
reg_addr->reg_report_rate is initialized to 0x00 by devm_kzalloc() (in
edt_ft5x06_ts_probe()) and not changed thereafter. So the checks do
not work and an access to register 0x00 is done.
Fix by setting reg_addr->reg_report_rate to NO_REGISTER.
Also fix the only place where reg_report_rate is checked against zero
instead of NO_REGISTER.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Don't populate the const array header on the stack, instead make it
static. Makes the object code smaller by over 180 bytes:
Before:
text data bss dec hex filename
6003 1536 0 7539 1d73 surface3_spi.o
After:
text data bss dec hex filename
5726 1632 0 7358 1cbe surface3_spi.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
On some x86 tablets with a Goodix touchscreen, the Windows logo on the
front is a capacitive home button. Touching this button results in a touch
with bit 4 of the first byte set, while only the lower 4 bits (0-3) are
used to indicate the number of touches.
Report a KEY_LEFTMETA press when this happens.
Note that the hardware might support more than one button, in which
case the "id" byte of coor_data would identify the button in question.
This is not implemented as we don't have access to hardware with
multiple buttons.
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Provide support for controlling reset pin. If this is not driven
correctly the device will be held in reset and will not respond.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Switch mxt_data and interrupt to resource managed allocation methods,
which cleans up the driver slightly and prepares for adding
reset GPIO support.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fixes the following sparse warning:
drivers/input/touchscreen/mxs-lradc-ts.c:33:12: warning:
symbol 'mxs_lradc_ts_irq_names' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[dtor: changed to static const char * const]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Function devm_ioremap() will return a NULL pointer on failure. However,
in function mxs_lradc_ts_probe(), its return value is checked with
IS_ERR(), which cannot detect the exceptional case.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
platform_get_resource() may fail, so we should better do a NULL check
and return error on failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core into next
This brings in devm_device_add_group() and friends so that we can create
driver-specific device attributes as managed resources.
|
|
The SUR40 labels all reported blobs as touch, token, or generic blob.
Previously, all blobs were reported as touch regardless of type, causing
lots of false positives. Present patch fixes this.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This information is unneccessary, even as debug output.
Leave commented out as documentation of the packet ID quirk.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Due to recent reverse engineering efforts, a lot more information is now
available about the internals of the SUR40. We document this in the kernel
driver for future use.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9086 624 0 9710 25ee drivers/input/touchscreen/ads7846.o
File size After adding 'const':
text data bss dec hex filename
9198 496 0 9694 25de drivers/input/touchscreen/ads7846.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9448 1008 0 10456 28d8 drivers/input/touchscreen/elants_i2c.o
File size After adding 'const':
text data bss dec hex filename
9496 944 0 10440 28c8 drivers/input/touchscreen/elants_i2c.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
7801 560 0 8361 20a9 drivers/input/touchscreen/raydium_i2c_ts.o
File size After adding 'const':
text data bss dec hex filename
7849 496 0 8345 2099 drivers/input/touchscreen/raydium_i2c_ts.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We get a harmless warning when CONFIG_RUNTIME_PM is disabled:
drivers/input/touchscreen/stmfts.c:760:12: error: 'stmfts_runtime_resume' defined but not used [-Werror=unused-function]
static int stmfts_runtime_resume(struct device *dev)
drivers/input/touchscreen/stmfts.c:748:12: error: 'stmfts_runtime_suspend' defined but not used [-Werror=unused-function]
static int stmfts_runtime_suspend(struct device *dev)
The regular PM functions are already marked as __maybe_unused, so let's
do the same for the runtime-PM as well.
Fixes: 78bcac7b2ae1 ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
Peter Rosin
Nick Dyer
Nick Dyer
Ethan Lee
Vittorio Gambaletta (VittGam)
Andi Shyti
Hans de Goede
Johan Hovold
Linus Torvalds
Martin Kepplinger
Greg Kroah-Hartman
Paul Cercueil
Chanwoo Choi
Jeff Lance
Christoph Hellwig
Dmitry Torokhov
Luca Ceresoli
Colin Ian King
Sergei A. Trusov
Sebastian Reichel
Arvind Yadav
Julia Lawall
Wei Yongjun
Pan Bian
Fabio Estevam
Florian Echtler
Arnd Bergmann