| Age | Commit message (Collapse) | Author |
|---|
|
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
|
|
Commit f9b9faf6d94dd29eab8c128905c7d091f955481d "drm: flip-work: change
drm_flip_work_init prototype" changed the drm_flip_work_init prototype
to a void function, which makes 'ret' an unused variable.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://people.freedesktop.org/~tagr/linux into drm-next
drm: Sanitize DRM_IOCTL_MODE_CREATE_DUMB input
Some drivers erroneously treat the .pitch and .size fields of struct
drm_mode_create_dumb as inputs. While the include/uapi/drm/drm_mode.h
header has a comment denoting them as outputs, that seemingly wasn't
enough to make drivers use them properly.
The result is that some userspace doesn't explicitly zero out those
fields, assuming that the kernel won't use them. That causes problems
since the data within the structure might be uninitialized, so bogus
data may end up confusing drivers (ridiculously large values for the
pitch, ...).
This series attempts to improve the situation by fixing all drivers to
not use the output fields. Furthermore to spare new drivers this bad
surprise, the DRM core now zeros out these fields prior to handing the
data structure to the driver.
Lessons learned from this are that future IOCTLs should be properly
documented (in the DRM DocBook for example) and should be rigorously
defined. To prevent misuse like this, userspace should be required to
zero out all output fields. The kernel should check for this and fail
if that's not the case.
* tag 'drm/gem-cma/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux:
drm/cma: Remove call to drm_gem_free_mmap_offset()
drm: Sanitize DRM_IOCTL_MODE_CREATE_DUMB input
drm/rcar: gem: dumb: pitch is an output
drm/omap: gem: dumb: pitch is an output
drm/cma: Introduce drm_gem_cma_dumb_create_internal()
drm/doc: Add GEM/CMA helpers to kerneldoc
drm/doc: mm: Fix indentation
drm/gem: Fix a few kerneldoc typos
|
|
Now that we're using lists instead of kfifo to store drm flip-work tasks
we do not need the size parameter passed to drm_flip_work_init function
anymore.
Moreover this function cannot fail anymore, we can thus remove the return
code.
Modify drm_flip_work_init users to take account of these changes.
[airlied: fixed two unused variable warnings]
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When creating a dumb buffer object using the DRM_IOCTL_MODE_CREATE_DUMB
IOCTL, only the width, height, bpp and flags fields are inputs. The
caller is not guaranteed to zero out or set handle, pitch and size.
Drivers must not treat these values as possible inputs, otherwise they
may use uninitialized memory during the computation of the framebuffer
size.
The OMAP driver uses the pitch field passed in by userspace as a minimum
and only override it if the driver-computed pitch is larger than what
userspace provided. To prevent this from causing overallocation, fix the
minimum pitch to 0 to enforce the driver-computed pitch.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
v2: Don't forget git add, noticed by David.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
|
|
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
|
|
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Regular randconfig nightly testing has detected problems with omapdrm.
omapdrm fails to build when the kernel is built to support 64-bit DMA
addresses and/or 64-bit physical addresses due to an assumption about
the width of these types.
Use %pad to print DMA addresses, rather than %x or %Zx (which is even
more wrong than %x). Avoid passing a uint32_t pointer into a function
which expects dma_addr_t pointer.
drivers/gpu/drm/omapdrm/omap_plane.c: In function 'omap_plane_pre_apply':
drivers/gpu/drm/omapdrm/omap_plane.c:145:2: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_plane.c:145:2: error: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Werror=format]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_plane.o] Error 1
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_get_paddr':
drivers/gpu/drm/omapdrm/omap_gem.c:794:4: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_describe':
drivers/gpu/drm/omapdrm/omap_gem.c:991:4: error: format '%Zx' expects argument of type 'size_t', but argument 7 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_init':
drivers/gpu/drm/omapdrm/omap_gem.c:1470:4: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Werror=format]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_gem.o] Error 1
drivers/gpu/drm/omapdrm/omap_dmm_tiler.c: In function 'dmm_txn_append':
drivers/gpu/drm/omapdrm/omap_dmm_tiler.c:226:2: error: passing argument 3 of 'alloc_dma' from incompatible pointer type [-Werror]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_dmm_tiler.o] Error 1
make[5]: Target `__build' not remade because of errors.
make[4]: *** [drivers/gpu/drm/omapdrm] Error 2
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Use the new drm_mode_create_rotation_property() in omapdrm.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make drm_property_create_bitmask() a bit more generic by allowing the
caller to specify which bits are in fact supported. This allows multiple
callers to use the same enum list, but still create different versions
of the same property with different list of supported bits.
v2: Populate values[] array as non-sparse
Make supported_bits 64bit
Fix up omapdrm call site (Rob)
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The rotation property stuff should be standardized among all drivers.
Move the bits to drm_crtc.h from omap_drv.h.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This allows reservation objects to be used in dma-buf. it's required
for implementing polling support on the fences that belong to a dma-buf.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com> #drivers/media/v4l2-core/
Acked-by: Thomas Hellstrom <thellstrom@vmware.com> #drivers/gpu/drm/ttm
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> #drivers/gpu/drm/armada/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm-next
* 'drm-next' of git://people.freedesktop.org/~dvdhrm/linux:
drm/omap: remove null test before kfree
drm/bochs: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN
drm/ttm: recognize ARM arch in ioprot handler
drm: enable render-nodes by default
drm/ttm: remove declaration of ttm_tt_cache_flush
drm/gem: remove misleading gfp parameter to get_pages()
drm/omap: use __GFP_DMA32 for shmem-backed gem
drm/i915: use shmem helpers if possible
Conflicts:
drivers/gpu/drm/drm_stub.c
|
|
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: David Airlie <airlied@linux.ie>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
|
|
drm_gem_get_pages() currently allows passing a 'gfp' parameter that is
passed to shmem combined with mapping_gfp_mask(). Given that the default
mapping_gfp_mask() is GFP_HIGHUSER, it is _very_ unlikely that anyone will
ever make use of that parameter. In fact, all drivers currently pass
redundant flags or 0.
This patch removes the 'gfp' parameter. The only reason to keep it is to
remove flags like __GFP_WAIT. But in its current form, it can only be used
to add flags. So to remove __GFP_WAIT, you'd have to drop it from the
mapping_gfp_mask, which again is stupid as this mask is used by shmem-core
for other allocations, too.
If any driver ever requires that parameter, we can introduce a new helper
that takes the raw 'gfp' parameter. The caller'd be responsible to combine
it with mapping_gfp_mask() in a suitable way. The current
drm_gem_get_pages() helper would then simply use mapping_gfp_mask() and
call the new helper. This is what shmem_read_mapping_pages{_gfp,} does
right now.
Moreover, the gfp-zone flag-usage is not obvious: If you pass a modified
zone, shmem core will WARN() or even BUG(). In other words, the following
must be true for 'gfp' passed to shmem_read_mapping_pages_gfp():
gfp_zone(mapping_gfp_mask(mapping)) == gfp_zone(gfp)
Add a comment to drm_gem_read_pages() explaining that constraint.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
|
|
OMAP requires bo-pages to be in the DMA32 zone. Explicitly request this by
setting __GFP_DMA32 as mapping-gfp-mask during shmem initialization. This
drops HIGHMEM from the gfp-mask and uses DMA32 instead. shmem-core takes
care to relocate pages during swap-in in case they have been loaded into
the wrong zone.
It is _not_ possible to pass __GFP_DMA32 to shmem_read_mapping_page_gfp()
as the page might have already been swapped-in at that time. The zone-mask
must be set during initialization and be kept constant for now.
Remove the now superfluous TODO in omap_gem.c.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
|
|
Make the omapdrm driver use the new HDMI ops when possible.
omapdrm will call set_hdmi_mode (when available) to tell the encoder
driver whether the monitor is a DVI or HDMI monitor, and if it's an HDMI
monitor, omapdrm will call set_hdmi_infoframe to to set the AVI
infoframe.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
|
|
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
With the recent primary-plane changes for drm, the primary plane's
framebuffer needs to be ref counted the same way as for
non-primary-planes. This was not done by the omapdrm driver, which
caused the ref count to drop to 0 too early, causing problems.
This patch moves the fb unref and ref from omap_plane_update to
omap_plane_mode_set. This way the fb refs are updated for both primary
and non-primary cases, as omap_plane_update calls omap_plane_mode_set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The vblank_cb callback and the page_flip ioctl can occur together in different
CPU contexts. vblank_cb uses takes tje drm device's event_lock spinlock when
sending the vblank event and updating omap_crtc->event and omap_crtc->od_fb.
Use the same spinlock in page_flip, to make sure the above omap_crtc parameters
are configured sequentially.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omap_crtc->old_fb is used to check whether the previous page flip has completed
or not. However, it's never initialized to anything, so it's always NULL. This
results in the check to always succeed, and the page_flip to proceed.
Initialize old_fb to the fb that we intend to flip to through page_flip, and
therefore prevent a future page flip to proceed if the last one didn't
complete.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The channel_names list didn't have a string populated for LCD3 manager, this
results in a crash when the display's output is connected to LCD3. Add an entry
for LCD3.
Reported-by: Somnath Mukherjee <somnath@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
A waiter of the type OMAP_GEM_READ should wait for a buffer to be completely
written, and only then proceed with reading it. A similar logic applies for
waiters with OMAP_GEM_WRITE flag.
Currently the function is_waiting() waits on the read_complete/read_target
counts in the sync object.
This should be the other way round, as a reader should wait for users who are
'writing' to this buffer, and vice versa.
Make readers of the buffer(OMAP_GEM_READ) wait on the write counters, and
writers to the buffer(OMAP_GEM_WRITE) wait on the read counters in is_waiting()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In omap_gem_op_async(), if a waiter is not added to the wait list, it needs to
be free'd in the function itself.
Make sure we free the waiter for this case.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Patch dfe96ddcfa22b44100814b9435770f6ff1309d37 (omapdrm: simplify locking in
the fb debugfs file) removed taking locks when using omapdrm's debugfs
to dump fb objects.
However, in omap_gem_describe we give a WARN is the lock has not been
taken, so that WARN is now seen every time omapdrm debugfs is used.
So, presuming the removal of locks is ok, we can also remove the WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
All the planes, including primary planes, are now destroyed by the drm
framework. Thus we no longer need the explicit call to plane->destroy
from the crtc's destroy function.
This patch removes the call, thus fixing the crash caused by double
freeing the plane.
remove omap_crtc->plane->funcs->destroy(omap_crtc->plane)
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Print a warning when the user tries to rotate a non-TILER framebuffer.
Also set the rotation to 0, to avoid constant flood of the warnings in
case of page flipping.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omap_fbdev_create() takes a reference to the fb's gem object with
omap_gem_get_paddr(). However, it never releases it with
omap_gem_put_paddr().
This patch adds the missing omap_gem_put_paddr() to omap_fbdev_free().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Plane rotation with omapdrm is currently broken.
It seems omap_plane_mode_set() expects width and height in screen
coordinates, so pass it like that.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
At the moment the omap_crtc_pre_apply() handles the enabling, disabling
and configuring of encoders and panels separately from the CRTC (i.e.
the overlay manager).
However, this doesn't work correctly. The encoder driver has to be in
control of its video input (i.e. the crtc) for correct operation.
This problem causes bugs with (at least) HDMI: the HDMI encoder supplies
pixel clock for DISPC, and DISPC supplies video stream for HDMI. The
current code first enables the HDMI encoder, and CRTC after that.
However, the encoder expects the video stream to start during the
encoder's enable, and if it doesn't, there will be sync lost errors.
The encoder enables its video source by calling src->enable(), and this
call goes to omapdrm (omap_crtc_enable), but omapdrm doesn't do anything
in that function. Similarly for disable, which goes to
omap_crtc_disable().
This patch moves the code to setup and enable/disable the crtc to
omap_crtc_enable. and omap_crtc_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
When an encoder is no longer connected to a crtc, the driver will leave
the encoder enabled.
This patch adds code to track the encoder used for a crtc, and when the
encoder changes, the old one is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
At module unload, omap_fbdev_free() gets called which releases the
framebuffers. However, the framebuffers are still used by crtcs, and
will be released only later at vsync. The driver doesn't wait for this,
and goes on to release the rest of the resources, which often
causes a crash.
This patchs adds a omap_crtc_flush() function which waits until the crtc
has finished with its apply queue and page flips.
The function utilizes a simple polling while-loop, as the performance is
not an issue here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
At the moment the DMM driver is never unregistered, even if it's
registered in the omapdrm module's init function. This means we'll get
errors when reloading the omapdrm module.
Fix this by unregistering the DMM driver properly, and also change the
module init to fail if DMM driver cannot be registered, simplifying the
unregister path as we don't need to keep the state whether we registered
the DMM driver or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
When unloading omapdrm driver, the omapdrm platform device is
uninitialized last, after the displays have been disconnected omap_crtc
callbacks have been removed. As the omapdrm pdev uninitialization needs
the features uninitialized in earlier steps, a crash is guaranteed.
This patch fixes the uninitialize order so that the omapdrm pdev is
removed first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
At the moment it's quite easy to get the following errors when the HDMI
output is enabled or disabled:
[drm:omap_crtc_error_irq] *ERROR* tv: errors: 00008000
The reason for the errors is that the omapdrm driver doesn't properly
handle the sync-lost irqs that happen when enabling the DIGIT crtc,
which is used for HDMI and analog TV. The driver does disable the
sync-lost irq properly, but it fails to wait until the output has been
fully enabled (i.e. the first vsync), so the sync-lost errors are still
seen occasionally.
This patch makes the omapdrm act the same way as the omapfb does:
- When enabling a display, we'll wait for the first vsync.
- When disabling a display, we'll wait for framedone if available, or
odd and even vsyncs.
These changes make sure the output is fully enabled or disabled at the
end of the function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Sanjay Singh Rawat <sanjay.rawat@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- drm:
Generic display port aux features, primary plane support, drm
master management fixes, logging cleanups, enforced locking checks
(instead of docs), documentation improvements, minor number
handling cleanup, pseudofs for shared inodes.
- ttm:
add ability to allocate from both ends
- i915:
broadwell features, power domain and runtime pm, per-process
address space infrastructure (not enabled)
- msm:
power management, hdmi audio support
- nouveau:
ongoing GPU fault recovery, initial maxwell support, random fixes
- exynos:
refactored driver to clean up a lot of abstraction, DP support
moved into drm, LVDS bridge support added, parallel panel support
- gma500:
SGX MMU support, SGX irq handling, asle irq work fixes
- radeon:
video engine bringup, ring handling fixes, use dp aux helpers
- vmwgfx:
add rendernode support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (849 commits)
DRM: armada: fix corruption while loading cursors
drm/dp_helper: don't return EPROTO for defers (v2)
drm/bridge: export ptn3460_init function
drm/exynos: remove MODULE_DEVICE_TABLE definitions
ARM: dts: exynos4412-trats2: enable exynos/fimd node
ARM: dts: exynos4210-trats: enable exynos/fimd node
ARM: dts: exynos4412-trats2: add panel node
ARM: dts: exynos4210-trats: add panel node
ARM: dts: exynos4: add MIPI DSI Master node
drm/panel: add S6E8AA0 driver
ARM: dts: exynos4210-universal_c210: add proper panel node
drm/panel: add ld9040 driver
panel/ld9040: add DT bindings
panel/s6e8aa0: add DT bindings
drm/exynos: add DSIM driver
exynos/dsim: add DT bindings
drm/exynos: disallow fbdev initialization if no device is connected
drm/mipi_dsi: create dsi devices only for nodes with reg property
drm/mipi_dsi: add flags to DSI messages
Skip intel_crt_init for Dell XPS 8700
...
|
|
drm-next
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/omap: Don't dereference list head when the connectors list is empty
drm/msm/mdp: add timeout for irq wait
drm/msm: validate flags, etc
drm/msm: use componentised device support
drm/msm: add chip-id param
drm/msm: crank down gpu when inactive
drm/msm: spin helper
drm/msm: add hang_debug module param
drm/msm: hdmi audio support
|
|
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
|
|
The connectors list iterator returns the list head when the list is
empty. Fix it by returning NULL in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
DRM drivers share a common address_space across all character-devices of a
single DRM device. This allows simple buffer eviction and mapping-control.
However, DRM core currently waits for the first ->open() on any char-dev
to mark the underlying inode as backing inode of the device. This delayed
initialization causes ugly conditions all over the place:
if (dev->dev_mapping)
do_sth();
To avoid delayed initialization and to stop reusing the inode of the
char-dev, we allocate an anonymous inode for each DRM device and reset
filp->f_mapping to it on ->open().
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
|
Linus Torvalds
Boris BREZILLON
Dave Airlie
Thierry Reding
Daniel Vetter
Wolfram Sang
David Herrmann
Russell King
Ville Syrjälä
Maarten Lankhorst
Fabian Frederick
Tomi Valkeinen
Thomas Wood
Rob Clark
Archit Taneja
Subhajit Paul
Grazvydas Ignotas
Matt Roper
Laurent Pinchart