| Age | Commit message (Collapse) | Author |
|---|
|
commit 376814f5fcf1aadda501d1413d56e8af85d19a97 upstream.
If there are no supported callbacks. We'll fall back to the
nominal clocks.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1170
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 17bdb4a82fe5014c8aa5b2103c80c5729744a096 upstream.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit fde9f39ac7f1ffd799a96ffa1e06b2051f0898f1 upstream.
This patch fixes a race condition that causes a use-after-free during
amdgpu_dm_atomic_commit_tail. This can occur when 2 non-blocking commits
are requested and the second one finishes before the first. Essentially,
this bug occurs when the following sequence of events happens:
1. Non-blocking commit #1 is requested w/ a new dm_state #1 and is
deferred to the workqueue.
2. Non-blocking commit #2 is requested w/ a new dm_state #2 and is
deferred to the workqueue.
3. Commit #2 starts before commit #1, dm_state #1 is used in the
commit_tail and commit #2 completes, freeing dm_state #1.
4. Commit #1 starts after commit #2 completes, uses the freed dm_state
1 and dereferences a freelist pointer while setting the context.
Since this bug has only been spotted with fast commits, this patch fixes
the bug by clearing the dm_state instead of using the old dc_state for
fast updates. In addition, since dm_state is only used for its dc_state
and amdgpu_dm_atomic_commit_tail will retain the dc_state if none is found,
removing the dm_state should not have any consequences in fast updates.
This use-after-free bug has existed for a while now, but only caused a
noticeable issue starting from 5.7-rc1 due to 3202fa62f ("slub: relocate
freelist pointer to middle of object") moving the freelist pointer from
dm_state->base (which was unused) to dm_state->context (which is
dereferenced).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207383
Fixes: bd200d190f45 ("drm/amd/display: Don't replace the dc_state for fast updates")
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: Mazin Rezk <mnrzk@protonmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 43a562774fceba867e8eebba977d7d42f8a2eac7 upstream.
Use kfree() instead of kvfree() to free rgb_user in
calculate_user_regamma_ramp() because the memory is allocated with
kcalloc().
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6eb3cf2e06d22b2b08e6b0ab48cb9c05a8e1a107 upstream.
[Why]
Changes that are fast don't require updating DLG parameters making
this call unnecessary. Considering this is an expensive call it should
not be done on every flip.
DML touches clocks, p-state support, DLG params and a few other DC
internal flags and these aren't expected during fast. A hang has been
reported with this change when called on every flip which suggests that
modifying these fields is not recommended behavior on fast updates.
[How]
Guard the validation to only happen if update type isn't FAST.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1191
Fixes: a24eaa5c51255b ("drm/amd/display: Revalidate bandwidth before commiting DC updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 34b86b75dfc90ab3d996c224314ce51772a3b351 upstream.
Mostly a cocci-job, but it flat out refused to remove the
declaration in drivers/gpu/drm/amd/display/dc/core/dc.c so
had to do that part manually.
@swap@
identifier TEMP;
expression A,B;
@@
- TEMP = A;
- A = B;
- B = TEMP;
+ swap(A, B);
@@
type T;
identifier swap.TEMP;
@@
(
- T TEMP;
|
- T TEMP = {...};
)
... when != TEMP
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a24eaa5c51255b344d5a321f1eeb3205f2775498 upstream.
[Why]
Whenever we switch between tiled formats without also switching pixel
formats or doing anything else that recreates the DC plane state we
can run into underflow or hangs since we're not updating the
DML parameters before committing to the hardware.
[How]
If the update type is FULL then call validate_bandwidth again to update
the DML parmeters before committing the state.
This is basically just a workaround and protective measure against
update types being added DC where we could run into this issue in
the future.
We can only fully validate the state in advance before applying it to
the hardware if we recreate all the plane and stream states since
we can't modify what's currently in use.
The next step is to update DM to ensure that we're creating the plane
and stream states for whatever could potentially be a full update in
DC to pre-emptively recreate the state for DC global validation.
The workaround can stay until this has been fixed in DM.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit f7d5991b92ff824798693ddf231cf814c9d5a88b upstream.
get_cursor_position already handles the case where the cursor has
negative off-screen coordinates by not setting
dc_cursor_position.enabled.
Signed-off-by: Simon Ser <contact@emersion.fr>
Fixes: 626bf90fe03f ("drm/amd/display: add basic atomic check for cursor plane")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e6142dd511425cb827b5db869f489eb81f5f994d upstream.
[why]
During hotplug, a DP port may be connected to the sink through
passive adapter which does not support DPCD reads. Issuing reads
without checking for this condition will result in errors
[how]
Ensure the link is in aux_mode before initiating operation that result
in a DPCD read.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 626bf90fe03fa080d8df06bb0397c95c53ae8e27 upstream.
This patch adds a basic cursor check when an atomic test-only commit is
performed. The position and size of the cursor plane is checked.
This should fix user-space relying on atomic checks to assign buffers to
planes.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reported-by: Roman Gilg <subdiff@gmail.com>
References: https://github.com/emersion/libliftoff/issues/46
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 87b7ebc2e16c14d32a912f18206a4d6cc9abc3e8 upstream.
[why]
We have seen a green screen after resume from suspend in a Raven system
connected with two displays (HDMI and DP) on X based system. We noticed
that this issue is related to bad DCC metadata from user space which may
generate hangs and consequently an underflow on HUBP. After taking a
deep look at the code path we realized that after resume we try to
restore the commit with the DCC enabled framebuffer but the framebuffer
is no longer valid.
[how]
This problem was only reported on Raven based system and after suspend,
for this reason, this commit adds a new parameter on
fill_plane_dcc_attributes() to give the option of disabling DCC
programmatically. In summary, for disabling DCC we first verify if is a
Raven system and if it is in suspend; if both conditions are true we
disable DCC temporarily, otherwise, it is enabled.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1099
Co-developed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2cc450ceaae4febc1539975247d235eb06c11979 upstream.
[Why]
Pitch, DCC, rotation and mirroring can result in updates that are not
UPDATE_TYPE_FAST but UPDATE_TYPE_MED instead. DC needs dc_plane_info
and dc_plane_size to make this determination and we aren't currently
passing this into DC during atomic check.
Underflow (visible or non-visible) can occur if we don't validate this
correctly. This also will generally trigger p-state warnings, typically
via the cursor handler when locking.
[How]
Get the framebuffer tiling flags and generate the required structures
for DC in dm_determine_update_type_for_commit.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9941b8129030c9202aaf39114477a0e58c0d6ffc upstream.
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 346d8a0a3c91888a412c2735d69daa09c00f0203 upstream.
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit dec9de2ada523b344eb2428abfedf9d6cd0a0029 upstream.
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a0275dfc82c9034eefbeffd556cca6dd239d7925 upstream.
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 5ac7fd2f597b88ee81f4748ee50cab06192a8dc3 upstream.
[Why]
If we have a single MST display and we disconnect it, we dont disable that
link. This causes the old link settings to still exist
Now on a replug for MST we think its a link loss and will try to reallocate
mst payload which will fail, throwing warning below.
[ 129.374192] [drm] Failed to updateMST allocation table forpipe idx:0
[ 129.374206] ------------[ cut here ]------------
[ 129.374284] WARNING: CPU: 14 PID: 1710 at
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc_link.c:3153
dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]
[ 129.374285] Modules linked in: amdgpu(OE) amd_iommu_v2 gpu_sched ttm
drm_kms_helper drm fb_sys_fops syscopyarea sysfillrect sysimgblt
binfmt_misc nls_iso8859_1 edac_mce_amd snd_hda_codec_realtek
snd_hda_codec_generic ledtrig_audio kvm snd_hda_codec_hdmi snd_hda_intel
snd_intel_nhlt snd_hda_codec irqbypass snd_hda_core snd_hwdep snd_pcm
snd_seq_midi snd_seq_midi_event snd_rawmidi crct10dif_pclmul snd_seq
crc32_pclmul ghash_clmulni_intel snd_seq_device snd_timer snd aesni_intel
eeepc_wmi crypto_simd asus_wmi joydev cryptd sparse_keymap input_leds
soundcore video glue_helper wmi_bmof mxm_wmi k10temp ccp mac_hid
sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4
hid_generic usbhid hid igb i2c_algo_bit ahci dca i2c_piix4 libahci
gpio_amdpt wmi gpio_generic
[ 129.374318] CPU: 14 PID: 1710 Comm: kworker/14:2 Tainted: G W OE 5.4.0-rc7bhawan+ #480
[ 129.374318] Hardware name: System manufacturer System Product Name/PRIME X370-PRO, BIOS 0515 03/30/2017
[ 129.374397] Workqueue: events dm_irq_work_func [amdgpu]
[ 129.374468] RIP: 0010:dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]
[ 129.374470] Code: 52 20 e8 1c 63 ad f4 48 8b 5d d0 65 48 33 1c 25 28 00
00 00 b8 01 00 00 00 75 16 48 8d 65 d8 5b 41 5c 41 5d 41 5e 41 5f 5d c3
<0f> 0b e9 fa fe ff ff e8 ed 5b d6 f3 41 0f b6 b6 c4 02 00 00 48 c7
[ 129.374471] RSP: 0018:ffff9f9141e7fcc0 EFLAGS: 00010246
[ 129.374472] RAX: 0000000000000000 RBX: ffff91ef0762f800 RCX: 0000000000000000
[ 129.374473] RDX: 0000000000000005 RSI: ffffffffc0c4a988 RDI: 0000000000000004
[ 129.374474] RBP: ffff9f9141e7fd10 R08: 0000000000000005 R09: 0000000000000000
[ 129.374475] R10: 0000000000000002 R11: 0000000000000001 R12: ffff91eebd510c00
[ 129.374475] R13: ffff91eebd510e58 R14: ffff91ef052c01b8 R15: 0000000000000006
[ 129.374476] FS: 0000000000000000(0000) GS:ffff91ef0ef80000(0000) knlGS:0000000000000000
[ 129.374477] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 129.374478] CR2: 000055623ea01d50 CR3: 0000000408a8c000 CR4: 00000000003406e0
[ 129.374479] Call Trace:
[ 129.374550] dc_link_reallocate_mst_payload+0x12e/0x150 [amdgpu]
[ 129.374617] dc_link_handle_hpd_rx_irq+0x6d4/0x6e0 [amdgpu]
[ 129.374693] handle_hpd_rx_irq+0x77/0x310 [amdgpu]
[ 129.374768] dm_irq_work_func+0x53/0x70 [amdgpu]
[ 129.374774] process_one_work+0x1fd/0x3f0
[ 129.374776] worker_thread+0x255/0x410
[ 129.374778] kthread+0x121/0x140
[ 129.374780] ? process_one_work+0x3f0/0x3f0
[ 129.374781] ? kthread_park+0x90/0x90
[ 129.374785] ret_from_fork+0x22/0x40
[How]
when we disable MST we should clear the cur link settings (lane_count=0 is
good enough). This will cause us to not reallocate payloads earlier than
expected and not throw the warning
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2b63d0ec0daf79ba503fa8bfa25e07dc3da274f3 upstream.
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c37243579d6c881c575dcfb54cf31c9ded88f946 upstream.
We might get different numbers of clocks from powerplay depending
on what the OEM has populated.
v2: add assert for at least one level
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3eb6d7aca53d81ce888624f09cd44dc0302161e8 upstream.
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf67d ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 6f8f76444baf405bacb0591d97549a71a9aaa1ac upstream.
[why]
Upon exiting a fixed active VRR state, the state isn't cleared. This
leads to the variable VRR range to be calculated incorrectly.
[how]
Set fixed active state to false when updating vrr params
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 58fe03d6dec908a1bec07eea7e94907af5c07eec upstream.
Disabling a display on MST can potentially happen after the entire MST
topology has been removed, which means that we can't communicate with
the topology at all in this scenario. Likewise, this also means that we
can't properly update payloads on the topology and as such, it's a good
idea to ignore payload update failures when disabling displays.
Currently, amdgpu makes the mistake of halting the payload update
process when any payload update failures occur, resulting in leaving
DC's local copies of the payload tables out of date.
This ends up causing problems with hotplugging MST topologies, and
causes modesets on the second hotplug to fail like so:
[drm] Failed to updateMST allocation table forpipe idx:1
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1511 at
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:2677
update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Modules linked in: cdc_ether usbnet fuse xt_conntrack nf_conntrack
nf_defrag_ipv6 libcrc32c nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4
nft_counter nft_compat nf_tables nfnetlink tun bridge stp llc sunrpc
vfat fat wmi_bmof uvcvideo snd_hda_codec_realtek snd_hda_codec_generic
snd_hda_codec_hdmi videobuf2_vmalloc snd_hda_intel videobuf2_memops
videobuf2_v4l2 snd_intel_dspcfg videobuf2_common crct10dif_pclmul
snd_hda_codec videodev crc32_pclmul snd_hwdep snd_hda_core
ghash_clmulni_intel snd_seq mc joydev pcspkr snd_seq_device snd_pcm
sp5100_tco k10temp i2c_piix4 snd_timer thinkpad_acpi ledtrig_audio snd
wmi soundcore video i2c_scmi acpi_cpufreq ip_tables amdgpu(O)
rtsx_pci_sdmmc amd_iommu_v2 gpu_sched mmc_core i2c_algo_bit ttm
drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec drm
crc32c_intel serio_raw hid_multitouch r8152 mii nvme r8169 nvme_core
rtsx_pci pinctrl_amd
CPU: 5 PID: 1511 Comm: gnome-shell Tainted: G O 5.5.0-rc7Lyude-Test+ #4
Hardware name: LENOVO FA495SIT26/FA495SIT26, BIOS R12ET22W(0.22 ) 01/31/2019
RIP: 0010:update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Code: 28 00 00 00 75 2b 48 8d 65 e0 5b 41 5c 41 5d 41 5e 5d c3 0f b6 06
49 89 1c 24 41 88 44 24 08 0f b6 46 01 41 88 44 24 09 eb 93 <0f> 0b e9
2f ff ff ff e8 a6 82 a3 c2 66 0f 1f 44 00 00 0f 1f 44 00
RSP: 0018:ffffac428127f5b0 EFLAGS: 00010202
RAX: 0000000000000002 RBX: ffff8d1e166eee80 RCX: 0000000000000000
RDX: ffffac428127f668 RSI: ffff8d1e166eee80 RDI: ffffac428127f610
RBP: ffffac428127f640 R08: ffffffffc03d94a8 R09: 0000000000000000
R10: ffff8d1e24b02000 R11: ffffac428127f5b0 R12: ffff8d1e1b83d000
R13: ffff8d1e1bea0b08 R14: 0000000000000002 R15: 0000000000000002
FS: 00007fab23ffcd80(0000) GS:ffff8d1e28b40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f151f1711e8 CR3: 00000005997c0000 CR4: 00000000003406e0
Call Trace:
? mutex_lock+0xe/0x30
dc_link_allocate_mst_payload+0x9a/0x210 [amdgpu]
? dm_read_reg_func+0x39/0xb0 [amdgpu]
? core_link_enable_stream+0x656/0x730 [amdgpu]
core_link_enable_stream+0x656/0x730 [amdgpu]
dce110_apply_ctx_to_hw+0x58e/0x5d0 [amdgpu]
? dcn10_verify_allow_pstate_change_high+0x1d/0x280 [amdgpu]
? dcn10_wait_for_mpcc_disconnect+0x3c/0x130 [amdgpu]
dc_commit_state+0x292/0x770 [amdgpu]
? add_timer+0x101/0x1f0
? ttm_bo_put+0x1a1/0x2f0 [ttm]
amdgpu_dm_atomic_commit_tail+0xb59/0x1ff0 [amdgpu]
? amdgpu_move_blit.constprop.0+0xb8/0x1f0 [amdgpu]
? amdgpu_bo_move+0x16d/0x2b0 [amdgpu]
? ttm_bo_handle_move_mem+0x118/0x570 [ttm]
? ttm_bo_validate+0x134/0x150 [ttm]
? dm_plane_helper_prepare_fb+0x1b9/0x2a0 [amdgpu]
? _cond_resched+0x15/0x30
? wait_for_completion_timeout+0x38/0x160
? _cond_resched+0x15/0x30
? wait_for_completion_interruptible+0x33/0x190
commit_tail+0x94/0x130 [drm_kms_helper]
drm_atomic_helper_commit+0x113/0x140 [drm_kms_helper]
drm_atomic_helper_set_config+0x70/0xb0 [drm_kms_helper]
drm_mode_setcrtc+0x194/0x6a0 [drm]
? _cond_resched+0x15/0x30
? mutex_lock+0xe/0x30
? drm_mode_getcrtc+0x180/0x180 [drm]
drm_ioctl_kernel+0xaa/0xf0 [drm]
drm_ioctl+0x208/0x390 [drm]
? drm_mode_getcrtc+0x180/0x180 [drm]
amdgpu_drm_ioctl+0x49/0x80 [amdgpu]
do_vfs_ioctl+0x458/0x6d0
ksys_ioctl+0x5e/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x1b0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fab2121f87b
Code: 0f 1e fa 48 8b 05 0d 96 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff
ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01
f0 ff ff 73 01 c3 48 8b 0d dd 95 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffd045f9068 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffd045f90a0 RCX: 00007fab2121f87b
RDX: 00007ffd045f90a0 RSI: 00000000c06864a2 RDI: 000000000000000b
RBP: 00007ffd045f90a0 R08: 0000000000000000 R09: 000055dbd2985d10
R10: 000055dbd2196280 R11: 0000000000000246 R12: 00000000c06864a2
R13: 000000000000000b R14: 0000000000000000 R15: 000055dbd2196280
---[ end trace 6ea888c24d2059cd ]---
Note as well, I have only been able to reproduce this on setups with 2
MST displays.
Changes since v1:
* Don't return false when part 1 or part 2 of updating the payloads
fails, we don't want to abort at any step of the process even if
things fail
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 840c90fce6c78bc6b2c4cb9e836d70985ed32066 upstream.
For high-res (8K) or HFR (4K120) displays, using uncompressed pixel
formats like YCbCr444 would exceed the bandwidth of HDMI 2.0, so the
"interesting" modes would be disabled, leaving only low-res or low
framerate modes.
This change lowers the pixel encoding to 4:2:2 or 4:2:0 if the max TMDS
clock is exceeded. Verified that 8K30 and 4K120 are now available and
working with a Samsung Q900R over an HDMI 2.0b link from a Radeon 5700.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Thomas Anderson <thomasanderson@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a51d9f8fe756beac51ce26ef54195da00a260d13 upstream.
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit dd998291dbe92106d8c4a7581c409b356928d711 upstream.
[WHY]
During detection:
function: get_active_converter_info populates link->dpcd_caps.dongle_caps
only when dpcd_rev >= DPCD_REV_11 and DWN_STRM_PORTX_TYPE is
DOWN_STREAM_DETAILED_HDMI or DOWN_STREAM_DETAILED_DP_PLUS_PLUS.
Otherwise, it is not cleared, and stale information remains.
During mode validation:
function: dp_active_dongle_validate_timing reads
link->dpcd_caps.dongle_caps->dongle_type to determine the maximum
pixel clock to support. This information is now stale and no longer
valid.
[HOW]
dp_active_dongle_validate_timing should be using
link->dpcd_caps->dongle_type instead.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 15caeabc5787c15babad7ee444afe9c26df1c8b3 upstream.
[Why]
When the driver sends a pipe set command to the DMCU FW, it does not wait
for the command to complete. This can lead to unpredictable behavior if,
for example, the driver were to request a pipe disable to the FW via MCP,
then power down some hardware before the firmware has completed processing
the command.
[How]
Wait for the DMCU FW to finish processing set pipe commands
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c59802313e84bede954235b3a5dd0dd5325f49c5 upstream.
[Why]
Some displays rely on the SPD verticle frequency maximum value.
Must round the calculated refresh rate to the nearest integer.
[How]
Round the nominal calculated refresh rate to the nearest whole
integer.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 616f5b65f1c02d3d6ae370644670d14c57de2fd8 upstream.
[Why]
The new implementation changed the behavior to allow process setMode
to DAL when DAL returns empty mode query for unplugged display.
This will trigger additional disable_link().
When unplug HDMI from MST dock, driver will update stream->signal to
"Virtual". disable_link() will call disable_output() if the signal type
is not DP and induce other displays on MST dock show black screen.
[How]
Don't need to process disable_output() if the signal type is virtual.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit b131932215c993ea5adf8192d1de2e8d6b23048d upstream.
[Why]
DP1.2 LL CTS test failure.
[How]
The failure is caused by not verify stream link is equal
to link, only check stream and link is not null.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 946621691f9919c263b4679b77f81f06019d3636 upstream.
dm_pp_get_clock_levels_by_type needs to add the default clocks
to the powerplay case as well. This was accidently dropped.
Fixes: b3ea88fef321de ("drm/amd/powerplay: add get_clock_by_type interface for display")
Bug: https://gitlab.freedesktop.org/drm/amd/issues/906
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit bc2fde42e2418808dbfc04de1a6da91d7d31cf1a upstream.
[WHY]
i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles
The call is expected to fail in DVI-D case but pass in HDMI case
Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D
[HOW]
Retry i2c_read to ensure failed result is valid
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 8775e89fa7121535d2da738c95167b8c65aa6e90 upstream.
[why]
A display that supports DRR can never really be considered
"synchronized" with any other display because we can dynamically
enable DRR (i.e. without modeset). this will cause their
relative CRTC positions to drift and lose sync. this will disrupt
features such as MCLK switching that assume and depend on
their permanent alignment (that can only change with modeset)
[how]
check for ignore_msa in stream when considered synchronizability
this ignore_msa is basically actually implemented as "supports drr"
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 104c307147ad379617472dd91a5bcb368d72bd6d upstream.
In dcn*_create_resource_pool the allocated memory should be released if
construct pool fails.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 055e547478a11a6360c7ce05e2afc3e366968a12 upstream.
In dcn*_clock_source_create when dcn20_clk_src_construct fails allocated
clk_src needs release.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[PG: drop chunk for driver not present in v5.2.x codebase.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
[ Upstream commit b5a41620bb88efb9fb31a4fa5e652e3d5bead7d4 ]
[Description]
port spdif fix to staging:
spdif hardwired to afmt inst 1.
spdif func pointer
spdif resource allocation (reserve last audio endpoint for spdif only)
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5382701c3520b3ed66169a6e4aa6ce5df8c56e0 ]
[Why]
The vm config will be clear to 0 when system enter S4. It will
cause hubbub didn't know how to fetch data when system resume.
The flip always pending because earliest_inuse_address and
request_address are different.
[How]
Reprogram VM config when system resume
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a463b263032f7c98c5912207db43be1aa34a6438 ]
[Why]
The math on deciding on how many
"frames to insert" sometimes sent us over the max refresh rate.
Also integer overflow can occur if we have high refresh rates.
[How]
Instead of clipping the frame duration such that it doesn’t go below the min,
just remove a frame from the number of frames to insert. +
Use unsigned long long for intermediate calculations to prevent
integer overflow.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1cbcfc975164f397b449efb17f59d81a703090db ]
[Why]
When endpoint is at the boundary of a region, such as at 2^0=1
we find that the last segment has a sharp slope and some points
are clipped at the top.
[How]
If end point is 1, which is exactly at the 2^0 region boundary, we
need to program an additional region beyond this point.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 88eac241a1fc500ce5274a09ddc4bd5fc2b5adb6 ]
[Why]
Specifically to one panel,
TCON is able to accept active video signal quickly, but
the Source Driver requires 2-3 frames of extra time.
It is a Panel issue since TCON needs to take care of
all Sink requirements including Source Driver. But in
this case it does not.
Customer is asking to add fixed T7 delay as panel
workaround.
[How]
Add monitor specific patch to add T7 delay
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bb264220d9316f6bd7c1fd84b8da398c93912931 upstream.
Laptops with AMD APU doesn't restore display backlight brightness after
system resume.
This issue started when DC was introduced.
Let's use BL_CORE_SUSPENDRESUME so the backlight core calls
update_status callback after system resume to restore the backlight
level.
Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495
(Raven Ridge).
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
undefined SW FP routines
[ Upstream commit 0f0727d971f6fdf8f1077180d495ddb9928f0c8b ]
arch/x86/Makefile disables SSE and SSE2 for the whole kernel. The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2. Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines for Clang.
This was originally landed in:
commit 10117450735c ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
but reverted in:
commit 193392ed9f69 ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
due to bugreports from GCC builds. Add guards to only do so for Clang.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=109487
Link: https://github.com/ClangBuiltLinux/linux/issues/327
Suggested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bd200d190f45b62c006d1ad0a63eeffd87db7a47 upstream.
[Why]
DRM private objects have no hw_done/flip_done fencing mechanism on their
own and cannot be used to sequence commits accordingly.
When issuing commits that don't touch the same set of hardware resources
like page-flips on different CRTCs we can run into the issue below
because of this:
1. Client requests non-blocking Commit #1, has a new dc_state #1,
state is swapped, commit tail is deferred to work queue
2. Client requests non-blocking Commit #2, has a new dc_state #2,
state is swapped, commit tail is deferred to work queue
3. Commit #2 work starts, commit tail finishes,
atomic state is cleared, dc_state #1 is freed
4. Commit #1 work starts,
commit tail encounters null pointer deref on dc_state #1
In order to change the DC state as in the private object we need to
ensure that we wait for all outstanding commits to finish and that
any other pending commits must wait for the current one to finish as
well.
We do this for MEDIUM and FULL updates. But not for FAST updates, nor
would we want to since it would cause stuttering from the delays.
FAST updates that go through dm_determine_update_type_for_commit always
create a new dc_state and lock the DRM private object if there are
any changed planes.
We need the old state to validate, but we don't actually need the new
state here.
[How]
If the commit isn't a full update then the use after free can be
resolved by simply discarding the new state entirely and retaining
the existing one instead.
With this change the sequence above can be reexamined. Commit #2 will
still free Commit #1's reference, but before this happens we actually
added an additional reference as part of Commit #2.
If an update comes in during this that needs to change the dc_state
it will need to wait on Commit #1 and Commit #2 to finish. Then it'll
swap the state, finish the work in commit tail and drop the last
reference on Commit #2's dc_state.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204181
Fixes: 004b3938e637 ("drm/amd/display: Check scaling info when determing update type")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 43d10d30df156f7834fa91aecb69614fefc8bb0a upstream.
[Why]
By passing through the dm_determine_update_type_for_commit for atomic
commits that can be done asynchronously we are incurring a
performance penalty by locking access to the global private object
and holding that access until the end of the programming sequence.
This is also allocating a new large dc_state on every access in addition
to retaining all the references on each stream and plane until the end
of the programming sequence.
[How]
Shift the determination for async update before validation. Return early
if it's going to be an async update.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e16e37efb4c9eb7bcb9dab756c975040c5257e98 upstream.
[Why]
We previously allowed framebuffer swaps as async updates for cursor
planes but had to disable them due to a bug in DRM with async update
handling and incorrect ref counting. The check to block framebuffer
swaps has been added to DRM for a while now, so this check is redundant.
The real fix that allows this to properly in DRM has also finally been
merged and is getting backported into stable branches, so dropping
this now seems to be the right time to do so.
[How]
Drop the redundant check for old_fb != new_fb.
With the proper fix in DRM, this should also fix some cursor stuttering
issues with xf86-video-amdgpu since it double buffers the cursor.
IGT tests that swap framebuffers (-varying-size for example) should
also pass again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7352193a33dfc9b69ba3bf6a8caea925b96243b1 ]
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ac25e6d5b2fbf251e9fa2f4131d42c815b43867 ]
[Why]
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0905f32977268149f06e3ce6ea4bd6d374dd891f ]
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 67fd6c0d2de8e51e84ff3fa6e68bbd524f823e49 ]
[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.
[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit feb7eb522e0a7a22c1e60d386bd3c3bfa1d5e4f7 ]
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74eda776d7a4e69ec7aa1ce30a87636f14220fbb ]
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Alex Deucher
Jerry (Fangzhi) Zuo
Mazin Rezk
Denis Efremov
Nicholas Kazlauskas
Ville Syrjälä
Simon Ser
Aurabindo Pillai
Rodrigo Siqueira
Yongqiang Sun
Isabel Zhang
Mario Kleiner
Josip Pavic
Bhawanpreet Lakha
Aric Cyr
Harry Wentland
Amanda Liu
Lyude Paul
Thomas Anderson
David Galiffi
Martin Tsai
Jing Zhou
Michael Strauss
Jun Lei
Navid Emamdoost
Charlene Liu
Lewis Huang
Bayan Zabihiyan
Anthony Koo
Kai-Heng Feng
Nick Desaulniers
Tai Man
Alvin Lee
Julian Parkin
Derek Lai
Eric Yang