| Age | Commit message (Collapse) | Author |
|---|
|
commit e1e047ace8cef6d143f38c7d769753f133becbe6 upstream.
Commit 2abb0d5268ae ("PM / devfreq: Lock devfreq in trans_stat_show")
revealed a missing locking while calling devfreq_update_status() function
during suspend/resume cycle.
Code analysis revealed that devfreq_set_target() function was called
without needed locks held for setting device specific suspend_freq if such
has been defined. This patch fixes that by adding the needed locking, what
fixes following kernel warning on Exynos4412-based OdroidU3 board during
system suspend:
PM: suspend entry (deep)
Filesystems sync: 0.002 seconds
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1385 at drivers/devfreq/devfreq.c:204 devfreq_update_status+0xc0/0x188
Modules linked in:
CPU: 2 PID: 1385 Comm: rtcwake Not tainted 5.4.0-rc6-next-20191111 #6848
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0112588>] (unwind_backtrace) from [<c010e070>] (show_stack+0x10/0x14)
[<c010e070>] (show_stack) from [<c0afb010>] (dump_stack+0xb4/0xe0)
[<c0afb010>] (dump_stack) from [<c01272e0>] (__warn+0xf4/0x10c)
[<c01272e0>] (__warn) from [<c01273a8>] (warn_slowpath_fmt+0xb0/0xb8)
[<c01273a8>] (warn_slowpath_fmt) from [<c07d105c>] (devfreq_update_status+0xc0/0x188)
[<c07d105c>] (devfreq_update_status) from [<c07d2d70>] (devfreq_set_target+0xb0/0x15c)
[<c07d2d70>] (devfreq_set_target) from [<c07d3598>] (devfreq_suspend+0x2c/0x64)
[<c07d3598>] (devfreq_suspend) from [<c05de0b0>] (dpm_suspend+0xa4/0x57c)
[<c05de0b0>] (dpm_suspend) from [<c05def74>] (dpm_suspend_start+0x98/0xa0)
[<c05def74>] (dpm_suspend_start) from [<c0195b58>] (suspend_devices_and_enter+0xec/0xc74)
[<c0195b58>] (suspend_devices_and_enter) from [<c0196a20>] (pm_suspend+0x340/0x410)
[<c0196a20>] (pm_suspend) from [<c019480c>] (state_store+0x6c/0xc8)
[<c019480c>] (state_store) from [<c033fc50>] (kernfs_fop_write+0x10c/0x228)
[<c033fc50>] (kernfs_fop_write) from [<c02a6d3c>] (__vfs_write+0x30/0x1d0)
[<c02a6d3c>] (__vfs_write) from [<c02a9afc>] (vfs_write+0xa4/0x180)
[<c02a9afc>] (vfs_write) from [<c02a9d58>] (ksys_write+0x60/0xd8)
[<c02a9d58>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed3d7fa8 to 0xed3d7ff0)
...
irq event stamp: 9667
hardirqs last enabled at (9679): [<c0b1e7c4>] _raw_spin_unlock_irq+0x20/0x58
hardirqs last disabled at (9698): [<c0b16a20>] __schedule+0xd8/0x818
softirqs last enabled at (9694): [<c01026fc>] __do_softirq+0x4fc/0x5fc
softirqs last disabled at (9719): [<c012fe68>] irq_exit+0x16c/0x170
---[ end trace 41ac5b57d046bdbc ]---
------------[ cut here ]------------
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 66d0e797bf095d407479c89952d42b1d96ef0a7f upstream.
This reverts commit 4585fbcb5331fc910b7e553ad3efd0dd7b320d14.
The name changing as devfreq(X) breaks some user space applications,
such as Android HAL from Unisoc and Hikey [1].
The device name will be changed unexpectly after every boot depending
on module init sequence. It will make trouble to setup some system
configuration like selinux for Android.
So we'd like to revert it back to old naming rule before any better
way being found.
[1] https://lkml.org/lkml/2018/5/8/1042
Cc: John Stultz <john.stultz@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Orson Zhai <orson.unisoc@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit eff5d31f7407fa9d31fb840106f1593399457298 upstream.
To build test, add COMPILE_TEST depedency to both ARM_RK3399_DMC_DEVFREQ
and DEVFREQ_EVENT_ROCKCHIP_DFI configuration. And ARM_RK3399_DMC_DEVFREQ
used the SMCCC interface so that add HAVE_ARM_SMCCC dependency to prevent
the build break.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2fee1a7cc6b1ce6634bb0f025be2c94a58dfa34d upstream.
The commit 4585fbcb5331 ("PM / devfreq: Modify the device name as devfreq(X) for
sysfs") changed the node name to devfreq(x). After this commit, it is not
possible to get the device name through /sys/class/devfreq/devfreq(X)/*.
Add new name attribute in order to get device name.
Cc: stable@vger.kernel.org
Fixes: 4585fbcb5331 ("PM / devfreq: Modify the device name as devfreq(X) for sysfs")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit d68adc8f85cd757bd33c8d7b2660ad6f16f7f3dc upstream.
The governor is initialized after sysfs attributes become visible so in
theory the governor field can be NULL here.
Fixes: bcf23c79c4e46 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 42a6b25e67df6ee6675e8d1eaf18065bd73328ba upstream.
Right now devfreq_dev_release will print a warning and abort the rest of
the cleanup if the devfreq instance is not part of the global
devfreq_list. But this is a valid scenario, for example it can happen if
the governor can't be found or on any other init error that happens
after device_register.
Initialize devfreq->node to an empty list head in devfreq_add_device so
that list_del becomes a safe noop inside devfreq_dev_release and we can
continue the rest of the cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e7cc792d00049c874010b398a27c3cc7bc8fef34 upstream.
The devfreq_notifier_call functions will update scaling_min_freq and
scaling_max_freq when the OPP table is updated.
If fetching the maximum frequency fails then scaling_max_freq remains
set to zero which is confusing. Set to ULONG_MAX instead so we don't
need special handling for this case in other places.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit e876e710ede23f670494331e062d643928e4142a upstream.
Notifier callbacks shouldn't return negative errno but one of the
NOTIFY_OK/DONE/BAD values.
The OPP core will ignore return values from notifiers but returning a
value that matches NOTIFY_STOP_MASK will stop the notification chain.
Fix by always returning NOTIFY_OK.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 2abb0d5268ae7b5ddf82099b1f8d5aa8414637d4 upstream.
There is no locking in this sysfs show function so stats printing can
race with a devfreq_update_status called as part of freq switching or
with initialization.
Also add an assert in devfreq_update_status to make it clear that lock
must be held by caller.
Fixes: 39688ce6facd ("PM / devfreq: account suspend/resume for stats")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 62bacb06b9f08965c4ef10e17875450490c948c0 upstream.
The kHz to Hz is incorrectly converted in a few places in the code,
this results in a wrong frequency being calculated because devfreq core
uses OPP frequencies that are given in Hz to clamp the rate, while
tegra-devfreq gives to the core value in kHz and then it also expects to
receive value in kHz from the core. In a result memory freq is always set
to a value which is close to ULONG_MAX because of the bug. Hence the EMC
frequency is always capped to the maximum and the driver doesn't do
anything useful. This patch was tested on Tegra30 and Tegra124 SoC's, EMC
frequency scaling works properly now.
Cc: <stable@vger.kernel.org> # 4.14+
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
[ Upstream commit 0465814831a926ce2f83e8f606d067d86745234e ]
The recent commit of
PM / devfreq: passive: Use non-devm notifiers
had incurred compiler warning, "unused variable 'dev'".
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c2b20e0da89c76759ee28c6824413ab2fa3bfc6 ]
Regulators should be enabled before clocks to avoid h/w hang. This
require change in exynos_bus_probe() to move exynos_bus_parse_of()
after exynos_bus_parent_parse_of() and change in error handling.
Similar change is needed in exynos_bus_exit() where clock should be
disabled before regulators.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ef7c7cce43f6ecc2b96d447e69b2900a9655f7c ]
The devfreq passive governor registers and unregisters devfreq
transition notifiers on DEVFREQ_GOV_START/GOV_STOP using devm wrappers.
If devfreq itself is registered with devm then a warning is triggered on
rmmod from devm_devfreq_unregister_notifier. Call stack looks like this:
devm_devfreq_unregister_notifier+0x30/0x40
devfreq_passive_event_handler+0x4c/0x88
devfreq_remove_device.part.8+0x6c/0x9c
devm_devfreq_dev_release+0x18/0x20
release_nodes+0x1b0/0x220
devres_release_all+0x78/0x84
device_release_driver_internal+0x100/0x1c0
driver_detach+0x4c/0x90
bus_remove_driver+0x7c/0xd0
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
imx_devfreq_platdrv_exit+0x14/0xd40 [imx_devfreq]
This happens because devres_release_all will first remove all the nodes
into a separate todo list so the nested devres_release from
devm_devfreq_unregister_notifier won't find anything.
Fix the warning by calling the non-devm APIS for frequency notification.
Using devm wrappers is not actually useful for a governor anyway: it
relies on the devfreq core to correctly match the GOV_START/GOV_STOP
notifications.
Fixes: 996133119f57 ("PM / devfreq: Add new passive governor")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7544fd7f384591038646d3cd9efb311ab4509e24 ]
A bit unexpectedly (but still documented), request_module may
return a positive value, in case of a modprobe error.
This is currently causing issues in the devfreq framework.
When a request_module exits with a positive value, we currently
return that via ERR_PTR. However, because the value is positive,
it's not a ERR_VALUE proper, and is therefore treated as a
valid struct devfreq_governor pointer, leading to a kernel oops.
Fix this by returning -EINVAL if request_module returns a positive
value.
Fixes: b53b0128052ff ("PM / devfreq: Fix static checker warning in try_then_request_governor")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch add basic tracing of the devfreq workqueue and delayed work.
It aims to capture changes of the polling intervals and device state.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
on-die termination (ODT) and auto power down parameters from kernel,
this patch adds the functionality to do this. Also, if DDR clock
frequency is lower than the on-die termination (ODT) disable frequency
this driver should disable the DDR ODT.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Some rk3399 GRF (Generic Register Files) definitions can be used for
different drivers. Move these definitions to a common include so we
don't need to duplicate these definitions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Force all Exynos buses to safe operation points before doing the system
reboot operation. There are board on which some aggressive power saving
operation points are behind the capabilities of the bootloader to properly
reset the hardware and boot the board. This way one can avoid board crash
early after reboot.
This fixes reboot issue on OdroidU3 board both with eMMC and SD boot.
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The patch 23c7b54ca1cd: "PM / devfreq: Fix devfreq_add_device() when
drivers are built as modules." leads to the following static checker
warning:
drivers/devfreq/devfreq.c:1043 governor_store()
warn: 'governor' can also be NULL
The reason is that the try_then_request_governor() function returns both
error pointers and NULL. It should just return error pointers, so fix
this by returning a ERR_PTR to the error intead of returning NULL.
Fixes: 23c7b54ca1cd ("PM / devfreq: Fix devfreq_add_device() when drivers are built as modules.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
If the new governor fails to start, switch back to old governor so that the
devfreq state is not left in some weird limbo.
[Myungjoo: assume fatal on revert failure and set df->governor to NULL]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This variable is not used after initialization, so
remove it. And in order to unify the code style,
move the location where the dev_get_drvdata is called
by the way.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The semicolon is unneeded, so remove it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The semicolon is unneeded, so remove it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Following up with complaints on inconsistent indentation from
Yangtao Li, this fixes indentation inconsistency.
In principle, this tries to put arguments aligned to the left
including the first argument except for the case where
the first argument is on the far-right side.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Yangtao Li <tiny.windzz@gmail.com>
|
|
devm_kzalloc() could fail, so insert a check of its return value. And
if it fails, returns -ENOMEM.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
'devfreq' is malloced in devfreq_add_device() and should be freed in
the error handling cases, otherwise it will cause memory leak.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch adds implementation for global suspend/resume for
devfreq framework. System suspend will next use these functions.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The patch prepares devfreq device for handling suspend/resume
functionality. The new fields will store needed information during this
process. Devfreq framework handles opp-suspend DT entry and there is no
need of modyfications in the drivers code. It uses atomic variables to
make sure no race condition affects the process.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The refactoring is needed for the new client in devfreq: suspend.
To avoid code duplication, move it to the new local function
devfreq_set_target.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
kfree has taken the null pointer into account. hence it is safe
to remove the redundant null pointer check before kfree.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
device_release() is freeing the resources before calling the device
specific release callback which is, in the case of devfreq, stopping
the governor.
It is a problem as some governors are using the device resources. e.g.
simpleondemand which is using the devfreq deferrable monitoring work. If it
is not stopped before the resources are freed, it might lead to a use after
free.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: John Einar Reitan <john.reitan@arm.com>
[cw00.choi: Fix merge conflict]
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Currently update_devfreq() is only visible to devfreq governors outside
of devfreq.c. Make it public to allow drivers that adjust devfreq policies
to cause a re-evaluation of the frequency after a policy change.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Several governors use the user space limits df->min/max_freq to adjust
the target frequency. This is not necessary, since update_devfreq()
already takes care of this. Instead the governor can request the available
min/max frequency by setting the target frequency to DEVFREQ_MIN/MAX_FREQ
and let update_devfreq() take care of any adjustments.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Commit ab8f58ad72c4 ("PM / devfreq: Set min/max_freq when adding the
devfreq device") initializes df->min/max_freq with the min/max OPP when
the device is added. Later commit f1d981eaecf8 ("PM / devfreq: Use the
available min/max frequency") adds df->scaling_min/max_freq and the
following to the frequency adjustment code:
max_freq = MIN(devfreq->scaling_max_freq, devfreq->max_freq);
With the current handling of min/max_freq this is incorrect:
Even though df->max_freq is now initialized to a value != 0 user space
can still set it to 0, in this case max_freq would be 0 instead of
df->scaling_max_freq as intended. In consequence the frequency adjustment
is not performed:
if (max_freq && freq > max_freq) {
freq = max_freq;
To fix this set df->min/max freq to the min/max OPP in max/max_freq_store,
when the user passes a value of 0. This also prevents df->max_freq from
being set below the min OPP when df->min_freq is 0, and similar for
min_freq. Since it is now guaranteed that df->min/max_freq can't be 0 the
checks for this case can be removed.
Fixes: f1d981eaecf8 ("PM / devfreq: Use the available min/max frequency")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Drop the custom MIN/MAX macros in favour of the standard min/max from
kernel.h
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
When the devfreq driver and the governor driver are built as modules,
the call to devfreq_add_device() or governor_store() fails because the
governor driver is not loaded at the time the devfreq driver loads. The
devfreq driver has a build dependency on the governor but also should
have a runtime dependency. We need to make sure that the governor driver
is loaded before the devfreq driver.
This patch fixes this bug by adding a try_then_request_governor()
function. First tries to find the governor, and then, if it is not found,
it requests the module and tries again.
Fixes: 1b5c1be2c88e (PM / devfreq: map devfreq drivers to governor using name)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
|
|
The opp table is not removed when the driver is unloaded neither when
there is an error within probe, so if the driver is reloaded the opp
core shows the following warning:
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
200000000, volt: 900000, enabled: 1. New: freq: 200000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
400000000, volt: 900000, enabled: 1. New: freq: 400000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
666000000, volt: 900000, enabled: 1. New: freq: 666000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
800000000, volt: 900000, enabled: 1. New: freq: 800000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
928000000, volt: 900000, enabled: 1. New: freq: 928000000,
volt: 900000, enabled: 1
This patch fixes the error path in the probe function and adds a .remove
function to properly cleanup the opp table on unloading.
Fixes: 5a893e31a636c (PM / devfreq: rockchip: add devfreq driver for rk3399 dmc)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Commit ab8f58ad72c4 ("PM / devfreq: Set min/max_freq when adding
the devfreq device") introduced the initialization of the user
limits min/max_freq from the lowest/highest available OPPs. Later
commit f1d981eaecf8 ("PM / devfreq: Use the available min/max
frequency") added scaling_min/max_freq, which actually represent
the frequencies of the lowest/highest available OPP. scaling_min/
max_freq are initialized with the values from min/max_freq, which
is totally correct in the context, but a bit awkward to read.
Swap the initialization and assign scaling_min/max_freq with the
OPP freqs and then the user limts min/max_freq with scaling_min/
max_freq.
Needless to say that this change is a NOP, intended to improve
readability.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Fix some spelling mistakes in error and debug messages.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
We just return -EPROBE_DEFER error code to caller and do not
print error message when try to get center logic regulator
and DMC clock defer.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
We have already wait dcf done in ATF, so don't need wait dcf irq
in kernel, besides, clear dcf irq in kernel will import competiton
between kernel and ATF, only handle dcf irq in ATF is a better way.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Never directly free @dev after calling device_register() or
device_unregister(), even if device_register() returned an error.
Always use put_device() to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
allocation in exynos_ppmu_probe()
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
Marek Szyprowski
Orson Zhai
Chanwoo Choi
Leonard Crestez
Dmitry Osipenko
MyungJoo Ham
Kamil Konieczny
Ezequiel Garcia
Thomas Gleixner
Lukasz Luba
Enric Balletbo i Serra
Saravana Kannan
Yangtao Li
Rob Herring
zhong jiang
Vincent Donnefort
Matthias Kaehlcke
Bjorn Andersson
Linus Torvalds
Lin Huang
Arvind Yadav
Markus Elfring