| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 4c5681fcc684c762b09435de3e82ffeee7769d21 ]
What we read back from the register is going to be capped at 32-bits,
and cpufreq_freq_table.frequency is an unsigned int. Avoid any possible
value truncation by using the appropriate return value.
Fixes: de322e085995 ("cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 22a26cc6a51ef73dcfeb64c50513903f6b2d53d8 ]
There is a logical error in brcm_avs_is_firmware_loaded() whereby if the
firmware returns -EINVAL, we will be reporting this as an error. The
comment is correct, the code was not.
Fixes: de322e085995 ("cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 46770be0cf94149ca48be87719bda1d951066644 ]
The cpufreq core heavily depends on the availability of the struct
device for CPUs and if they aren't available at the time cpufreq driver
is registered, we will never succeed in making cpufreq work.
This happens due to following sequence of events:
- cpufreq_register_driver()
- subsys_interface_register()
- return 0; //successful registration of driver
... at a later point of time
- register_cpu();
- device_register();
- bus_probe_device();
- sif->add_dev();
- cpufreq_add_dev();
- get_cpu_device(); //FAILS
- per_cpu(cpu_sys_devices, num) = &cpu->dev; //used by get_cpu_device()
- return 0; //CPU registered successfully
Because the per-cpu variable cpu_sys_devices is set only after the CPU
device is regsitered, cpufreq will never be able to get it when
cpufreq_add_dev() is called.
This patch avoids this failure by making sure device structure of at
least CPU0 is available when the cpufreq driver is registered, else
return -EPROBE_DEFER.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit db0d32d84031188443e25edbd50a71a6e7ac5d1d upstream.
The following build warning occurred on powerpc 64-bit builds:
drivers/cpufreq/powernv-cpufreq.c: In function 'init_chip_info':
drivers/cpufreq/powernv-cpufreq.c:1070:1: warning: the frame size of
1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This is with a cross-compiler based on gcc 8.1.0, which I got from:
https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/8.1.0/
The warning is due to putting 1024 bytes on the stack:
unsigned int chip[256];
...and it's also undesirable to have a hard limit on the number of
CPUs here.
Fix both problems by dynamically allocating based on num_possible_cpus,
as recommended by Michael Ellerman.
Fixes: 053819e0bf840 ("cpufreq: powernv: Handle throttling due to Pmax capping at chip level")
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6e8df07268c1f75dd9215536e2ce4587b70f977 upstream.
Add NULL checks to show() and store() in cpufreq.c to avoid attempts
to invoke a NULL callback.
Though some interfaces of cpufreq are set as read-only, users can
still get write permission using chmod which can lead to a kernel
crash, as follows:
chmod +w /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
echo 1 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
This bug was found in linux 4.19.
Signed-off-by: Kai Shen <shenkai8@huawei.com>
Reported-by: Feilong Lin <linfeilong@huawei.com>
Reviewed-by: Feilong Lin <linfeilong@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 703cbaa601ff3fb554d1246c336ba727cc083ea0 upstream.
cpufreq_resume can be called even without preceding cpufreq_suspend.
This can happen in following scenario:
suspend_devices_and_enter
--> dpm_suspend_start
--> dpm_prepare
--> device_prepare : this function errors out
--> dpm_suspend: this is skipped due to dpm_prepare failure
this means cpufreq_suspend is skipped over
--> goto Recover_platform, due to previous error
--> goto Resume_devices
--> dpm_resume_end
--> dpm_resume
--> cpufreq_resume
In case schedutil is used as frequency governor, cpufreq_resume will
eventually call sugov_start, which does following:
memset(sg_cpu, 0, sizeof(*sg_cpu));
....
This effectively erases function pointer for frequency update, causing
crash later on. The function pointer would have been set correctly if
subsequent cpufreq_add_update_util_hook runs successfully, but that
function returns earlier because cpufreq_suspend was not called:
if (WARN_ON(per_cpu(cpufreq_update_util_data, cpu)))
return;
The fix is to check cpufreq_suspended first, if it's false, that means
cpufreq_suspend was not called in the first place, so do not resume
cpufreq.
Signed-off-by: Bo Yan <byan@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Dropped printing a message ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 248aefdcc3a7e0cfbd014946b4dead63e750e71b upstream
call of_node_put to release the refcount of np.
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65650b35133ff20f0c9ef0abd5c3c66dbce3ae57 upstream.
It is incorrect to set the cpufreq syscore shutdown callback pointer
to cpufreq_suspend(), because that function cannot be run in the
syscore stage of system shutdown for two reasons: (a) it may attempt
to carry out actions depending on devices that have already been shut
down at that point and (b) the RCU synchronization carried out by it
may not be able to make progress then.
The latter issue has been present since commit 45975c7d21a1 ("rcu:
Define RCU-sched API in terms of RCU for Tree RCU PREEMPT builds"),
but the former one has been there since commit 90de2a4aa9f3 ("cpufreq:
suspend cpufreq governors on shutdown") regardless.
Fix that by dropping cpufreq_syscore_ops altogether and making
device_shutdown() call cpufreq_suspend() directly before shutting
down devices, which is along the lines of what system-wide power
management does.
Fixes: 45975c7d21a1 ("rcu: Define RCU-sched API in terms of RCU for Tree RCU PREEMPT builds")
Fixes: 90de2a4aa9f3 ("cpufreq: suspend cpufreq governors on shutdown")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e0a12445d1cb186d875410d093a00d215bec6a89 ]
The cpu variable is still being used in the of_get_property() call
after the of_node_put() call, which may result in use-after-free.
Fixes: a9acc26b75f6 ("cpufreq/pasemi: fix possible object reference leak")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c468966f05ac9c17bb5948275283d34e6fe0660 ]
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/kirkwood-cpufreq.c:127:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function.
./drivers/cpufreq/kirkwood-cpufreq.c:133:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 118, but without a corresponding object release within this function.
and also do some cleanup:
- of_node_put(np);
- np = NULL;
...
of_node_put(np);
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d10dc28a9ea6e8c02e825dab28699f3c72b02d9 ]
The call to of_find_node_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a9acc26b75f652f697e02a9febe2ab0da648a571 ]
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 233298032803f2802fe99892d0de4ab653bfece4 ]
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9a4f26cc98d81b67ecc23b890c28e2df324e29f3 ]
Currently the error return path from kobject_init_and_add() is not
followed by a call to kobject_put() - which means we are leaking
the kobject.
Fix it by adding a call to kobject_put() in the error path of
kobject_init_and_add().
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tobin C. Harding <tobin@kernel.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/20190430001144.24890-1-tobin@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f2c4db1bd80720cd8cb2a5aa220d9bc9f374f04e upstream
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1222d527f314c86a3b59a522115d62facc5a7965 ]
There is some rare cases where CPB (and possibly IDA) are missing on
processors.
This is the case fixed by commit f7f3dc00f612 ("x86/cpu/AMD: Fix
erratum 1076 (CPB bit)") and following.
In such context, the boost status isn't reported by
/sys/devices/system/cpu/cpufreq/boost.
This commit is about printing a message to report that the CPU
doesn't expose the boost capabilities.
This message could help debugging platforms hit by this phenomena.
Signed-off-by: Erwan Velu <e.velu@criteo.com>
[ rjw: Change the message text somewhat ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9505b98ccddc454008ca7efff90044e3e857c827 upstream.
pxa_cpufreq_init_voltages() is marked __init but usually inlined into
the non-__init pxa_cpufreq_init() function. When building with clang,
it can stay as a standalone function in a discarded section, and produce
this warning:
WARNING: vmlinux.o(.text+0x616a00): Section mismatch in reference from the function pxa_cpufreq_init() to the function .init.text:pxa_cpufreq_init_voltages()
The function pxa_cpufreq_init() references
the function __init pxa_cpufreq_init_voltages().
This is often because pxa_cpufreq_init lacks a __init
annotation or the annotation of pxa_cpufreq_init_voltages is wrong.
Fixes: 50e77fcd790e ("ARM: pxa: remove __init from cpufreq_driver->init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 446fae2bb5395f3028d8e3aae1508737e5a72ea1 upstream.
of_cpu_device_node_get() will increase the refcount of device_node,
it is necessary to call of_node_put() at the end to release the
refcount.
Fixes: 9eb15dbbfa1a2 ("cpufreq: Add cpufreq driver for Tegra124")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 625c85a62cb7d3c79f6e16de3cfa972033658250 upstream.
The cpufreq_global_kobject is created using kobject_create_and_add()
helper, which assigns the kobj_type as dynamic_kobj_ktype and show/store
routines are set to kobj_attr_show() and kobj_attr_store().
These routines pass struct kobj_attribute as an argument to the
show/store callbacks. But all the cpufreq files created using the
cpufreq_global_kobject expect the argument to be of type struct
attribute. Things work fine currently as no one accesses the "attr"
argument. We may not see issues even if the argument is used, as struct
kobj_attribute has struct attribute as its first element and so they
will both get same address.
But this is logically incorrect and we should rather use struct
kobj_attribute instead of struct global_attr in the cpufreq core and
drivers and the show/store callbacks should take struct kobj_attribute
as argument instead.
This bug is caught using CFI CLANG builds in android kernel which
catches mismatch in function prototypes for such callbacks.
Reported-by: Donghee Han <dh.han@samsung.com>
Reported-by: Sangkyu Kim <skwith.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2f66196208c98b3d1b4294edffb2c5a8197be899 ]
cpuinfo_cur_freq gets current CPU frequency as detected by hardware
while scaling_cur_freq last known CPU frequency. Some platforms may not
allow checking the CPU frequency of an offline CPU or the associated
resources may have been released via cpufreq_exit when the CPU gets
offlined, in which case the policy would have been invalidated already.
If we attempt to get current frequency from the hardware, it may result
in hang or crash.
For example on Juno, I see:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000188
[0000000000000188] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 5 PID: 4202 Comm: cat Not tainted 4.20.0-08251-ga0f2c0318a15-dirty #87
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : scmi_cpufreq_get_rate+0x34/0xb0
lr : scmi_cpufreq_get_rate+0x34/0xb0
Call trace:
scmi_cpufreq_get_rate+0x34/0xb0
__cpufreq_get+0x34/0xc0
show_cpuinfo_cur_freq+0x24/0x78
show+0x40/0x60
sysfs_kf_seq_show+0xc0/0x148
kernfs_seq_show+0x44/0x50
seq_read+0xd4/0x480
kernfs_fop_read+0x15c/0x208
__vfs_read+0x60/0x188
vfs_read+0x94/0x150
ksys_read+0x6c/0xd8
__arm64_sys_read+0x24/0x30
el0_svc_common+0x78/0x100
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
---[ end trace 3d1024e58f77f6b2 ]---
So fix the issue by checking if the policy is invalid early in
__cpufreq_get before attempting to get the current frequency.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ef28a04d1ccf718eee069b72132ce4aa1e52ab9 ]
Add return value check for voltage scale when ARM clock
rate change fail.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 51c99dd2c06b234575661fa1e0a1dea6c3ef566f ]
We can not call dev_pm_opp_of_cpumask_remove_table() freely anymore
since the latest OPP core updates as that uses reference counting to
free resources. There are cases where no static OPPs are added (using
DT) for a platform and trying to remove the OPP table may end up
decrementing refcount which is already zero and hence generating
warnings.
Lets track if we were able to add static OPPs or not and then only
remove the table based on that. Some reshuffling of code is also done to
do that.
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da5e79bc70b84971d2b3a55fb252e34e51d81d48 upstream.
If the policy limits change between invocations of cs_dbs_update(),
the requested frequency value stored in dbs_info may not be updated
and the function may use a stale value of it next time. Moreover, if
idle periods are takem into account by cs_dbs_update(), the requested
frequency value stored in dbs_info may be below the min policy limit,
which is incorrect.
To fix these problems, always update the requested frequency value
in dbs_info along with the local copy of it when the previous
requested frequency is beyond the policy limits and avoid decreasing
the requested frequency below the min policy limit when taking
idle periods into account.
Fixes: abb6627910a1 (cpufreq: conservative: Fix next frequency selection)
Fixes: 00bfe05889e9 (cpufreq: conservative: Decrease frequency faster for deferred updates)
Reported-by: Waldemar Rymarkiewicz <waldemarx.rymarkiewicz@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Waldemar Rymarkiewicz <waldemarx.rymarkiewicz@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a3eb51e30b9ac66fe1b75877627a7e4aaeca24a upstream.
If cppc_cpufreq.ko is deleted at the same time that tuned-adm is
changing profiles, there is a small chance that a race can occur
between cpufreq_dbs_governor_exit() and cpufreq_dbs_governor_limits()
resulting in a system failure when the latter tries to use
policy->governor_data that has been freed by the former.
This patch uses gov_dbs_data_mutex to synchronize access.
Fixes: e788892ba3cc (cpufreq: governor: Get rid of governor events)
Signed-off-by: Henry Willard <henry.willard@oracle.com>
[ rjw: Subject, minor white space adjustment ]
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95d6c0857e54b788982746071130d822a795026b upstream.
Currently, intel_pstate doesn't register if _PSS is not present on
HP Proliant systems, because it expects the firmware to take over
CPU performance scaling in that case. However, if ACPI PCCH is
present, the firmware expects the kernel to use it for CPU
performance scaling and the pcc-cpufreq driver is loaded for that.
Unfortunately, the firmware interface used by that driver is not
scalable for fundamental reasons, so pcc-cpufreq is way suboptimal
on systems with more than just a few CPUs. In fact, it is better to
avoid using it at all.
For this reason, modify intel_pstate to look for ACPI PCCH if _PSS
is not present and register if it is there. Also prevent the
pcc-cpufreq driver from trying to initialize itself if intel_pstate
has been registered already.
Fixes: fbbcdc0744da (intel_pstate: skip the driver if ACPI has power mgmt option)
Reported-by: Andreas Herrmann <aherrmann@suse.com>
Reviewed-by: Andreas Herrmann <aherrmann@suse.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Andreas Herrmann <aherrmann@suse.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4f3388afd488ed15368fa7413b8bd6d1f98bb1d upstream.
Add support to specify platform specific transition_delay_us instead
of using the transition delay derived from PCC.
With commit 3d41386d556d (cpufreq: CPPC: Use transition_delay_us
depending transition_latency) we are setting transition_delay_us
directly and not applying the LATENCY_MULTIPLIER. Because of that,
on Qualcomm Centriq we can end up with a very high rate of frequency
change requests when using the schedutil governor (default
rate_limit_us=10 compared to an earlier value of 10000).
The PCC subspace describes the rate at which the platform can accept
commands on the CPPC's PCC channel. This includes read and write
command on the PCC channel that can be used for reasons other than
frequency transitions. Moreover the same PCC subspace can be used by
multiple freq domains and deriving transition_delay_us from it as we
do now can be sub-optimal.
Moreover if a platform does not use PCC for desired_perf register then
there is no way to compute the transition latency or the delay_us.
CPPC does not have a standard defined mechanism to get the transition
rate or the latency at the moment.
Given the above limitations, it is simpler to have a platform specific
transition_delay_us and rely on PCC derived value only if a platform
specific value is not available.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Fixes: 3d41386d556d (cpufreq: CPPC: Use transition_delay_us depending transition_latency)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff7c9917143b3a6cf2fa61212a32d67cf259bf9c upstream.
When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
= max_state * policy->max / max_freq;
= 43 * (4000000/4500000) = 38 (3.8GHz)
= 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.
This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7592019634f8473f0b0973ce79297183077bdbc2 upstream.
According to current code implementation, detecting the long
idle period is done by checking if the interval between two
adjacent utilization update handlers is long enough. Although
this mechanism can detect if the idle period is long enough
(no utilization hooks invoked during idle period), it might
not cover a corner case: if the task has occupied the CPU
for too long which causes no context switches during that
period, then no utilization handler will be launched until this
high prio task is scheduled out. As a result, the idle_periods
field might be calculated incorrectly because it regards the
100% load as 0% and makes the conservative governor who uses
this field confusing.
Change the detection to compare the idle_time with sampling_rate
directly.
Reported-by: Artem S. Tashkinov <t.artem@mailcity.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7d1f119c48f64bebf0fa1e326af577c6152fe30 upstream.
If the policy limits are updated via cpufreq_update_policy() and
subsequently via sysfs, the limits stored in user_policy may be
set incorrectly.
For example, if both min and max are set via sysfs to the maximum
available frequency, user_policy.min and user_policy.max will also
be the maximum. If a policy notifier triggered by
cpufreq_update_policy() lowers both the min and the max at this
point, that change is not reflected by the user_policy limits, so
if the max is updated again via sysfs to the same lower value,
then user_policy.max will be lower than user_policy.min which
shouldn't happen. In particular, if one of the policy CPUs is
then taken offline and back online, cpufreq_set_policy() will
fail for it due to a failing limits check.
To prevent that from happening, initialize the min and max fields
of the new_policy object to the ones stored in user_policy that
were previously set via sysfs.
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b24b6478e65f140610ab1ffaadc7bc6bf0be8aad ]
Ideally the de-allocation of resources should happen in the exact
opposite order in which they were allocated. It helps maintain the code
in long term, even if nothing really breaks with incorrect ordering.
That wasn't followed in cpufreq_online() and it has some
inconsistencies. For example, the symlinks were created from within
the locked region while they are removed only after putting the locks.
Also ->exit() should have been called only after the symlinks are
removed and the lock is dropped, as that was the case when ->init()
was first called.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 55b55abc17f238c61921360e61dde90dd9a326d1 ]
Kmemleak reported the below leak. When cppc_cpufreq_init went into
failure path, the cpu mask is not freed. After fix, this report is
gone. And to avaoid potential NULL pointer reference, check the cpu
value first.
unreferenced object 0xffff800fd5ea4880 (size 128):
comm "swapper/0", pid 1, jiffies 4294939510 (age 668.680s)
hex dump (first 32 bytes):
00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 .... ...........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffff0000082c4ae4>] __kmalloc_node+0x278/0x634
[<ffff0000088f4a74>] alloc_cpumask_var_node+0x28/0x60
[<ffff0000088f4af0>] zalloc_cpumask_var+0x14/0x1c
[<ffff000008d20254>] cppc_cpufreq_init+0xd0/0x19c
[<ffff000008083828>] do_one_initcall+0xec/0x15c
[<ffff000008cd1018>] kernel_init_freeable+0x1f4/0x2a4
[<ffff0000089099b0>] kernel_init+0x18/0x10c
[<ffff000008084d50>] ret_from_fork+0x10/0x18
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8913315e9459b146e5888ab5138e10daa061b885 ]
When multiple CPUs are related in one cpufreq policy, the first online
CPU will be chosen by default to handle cpufreq operations. Let's take
cpu0 and cpu1 as an example.
When cpu0 is offline, policy->cpu will be shifted to cpu1. cpu1's perf
capabilities should be initialized. Otherwise, perf capabilities are 0s
and speed change can not take effect.
This patch copies perf capabilities of the first online CPU to other
shared CPUs when policy shared type is CPUFREQ_SHARED_TYPE_ANY.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c0f7f5b6c69107ca92909512533e70258ee19188 upstream.
gpstate_timer_handler() uses synchronous smp_call to set the pstate
on the requested core. This causes the below hard lockup:
smp_call_function_single+0x110/0x180 (unreliable)
smp_call_function_any+0x180/0x250
gpstate_timer_handler+0x1e8/0x580
call_timer_fn+0x50/0x1c0
expire_timers+0x138/0x1f0
run_timer_softirq+0x1e8/0x270
__do_softirq+0x158/0x3e4
irq_exit+0xe8/0x120
timer_interrupt+0x9c/0xe0
decrementer_common+0x114/0x120
-- interrupt: 901 at doorbell_global_ipi+0x34/0x50
LR = arch_send_call_function_ipi_mask+0x120/0x130
arch_send_call_function_ipi_mask+0x4c/0x130
smp_call_function_many+0x340/0x450
pmdp_invalidate+0x98/0xe0
change_huge_pmd+0xe0/0x270
change_protection_range+0xb88/0xe40
mprotect_fixup+0x140/0x340
SyS_mprotect+0x1b4/0x350
system_call+0x58/0x6c
One way to avoid this is removing the smp-call. We can ensure that the
timer always runs on one of the policy-cpus. If the timer gets
migrated to a cpu outside the policy then re-queue it back on the
policy->cpus. This way we can get rid of the smp-call which was being
used to set the pstate on the policy->cpus.
Fixes: 7bc54b652f13 ("timers, cpufreq/powernv: Initialize the gpstate timer as pinned")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Nicholas Piggin <npiggin@gmail.com>
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 70f6bf2a3b7e40c3f802b0ea837762a8bc6c1430 ]
When maxcpus=1 is in the kernel command line, the BP is responsible
for re-enabling the HWP - because currently only the APs invoke
intel_pstate_hwp_enable() during their online process - which might
put the system into unstable state after resume.
Fix this by enabling the HWP explicitly on BP during resume.
Reported-by: Doug Smythies <dsmythies@telus.net>
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Yu Chen <yu.c.chen@intel.com>
[ rjw: Subject/changelog, minor modifications ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d41386d556db9f720e00de3e11e45f39cb5071c upstream.
With commit e948bc8fbee0 (cpufreq: Cap the default transition delay
value to 10 ms) the cpufreq was not honouring the delay passed via
ACPI (PCCT). Due to which on ARM based platforms using CPPC the
cpufreq governor tries to change the frequency of CPUs faster than
expected.
This leads to continuous error messages like the following.
" ACPI CPPC: PCC check channel failed. Status=0 "
Earlier (without above commit) the default transition delay was
taken form the value passed from PCCT. Use the same value provided
by PCCT to set the transition_delay_us.
Fixes: e948bc8fbee0 (cpufreq: Cap the default transition delay value to 10 ms)
Signed-off-by: George Cherian <george.cherian@cavium.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ee1f4a7dafa997816ff3de96155c6f3edc21c1e6 ]
On POWERNV platform, the fields for pstates in the Power Management
Status Register (PMSR) and the Power Management Control Register
(PMCR) are 8-bits wide. On POWER8 the pstates are negatively numbered
while on POWER9 they are positively numbered.
The device-tree exports pstates as 32-bit entries. The device-tree
implementation sign-extends the 8-bit pstate values to obtain the
corresponding 32-bit entry.
Eg: On POWER8, a pstate value 0x82 [-126] is represented in the
device-tree as 0xfffffff82 while on POWER9, the same value 0x82 [130]
is represented in the device-tree as 0x00000082.
The powernv-cpufreq driver implementation represents pstates using the
integer type. In multiple places in the driver, the code interprets
the pstates extracted from the PMSR as a signed byte and assigns it to
a integer variable to get the sign-extention.
On POWER9 platforms which have greater than 128 pstates, this results
in the driver performing incorrect sign-extention, and thereby
treating a legitimate pstate (say 130) as an invalid pstates (since it
is interpreted as -126).
This patch fixes the issue by implementing a helper function to
extract Pstates from PMSR register, and correctly sign-extend it to be
consistent with the values provided by the device-tree.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 0049457bfde661cf47410eaacad65845c9a2bb45 which was
commit a8b149d32b663c1a4105273295184b78f53d33cf upstream.
The backport was not correct, so just drop it entirely.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1d0d064307cbfd8546841f6e9d94d02c55e45e1e ]
The commit e948bc8fbee0 ("cpufreq: Cap the default transition delay
value to 10 ms") caused a regression on EPIA-M min-ITX computer where
shutdown or reboot hangs occasionally with a print message like:
longhaul: Warning: Timeout while waiting for idle PCI bus
cpufreq: __target_index: Failed to change cpu frequency: -16
This probably happens because the cpufreq governor tries to change the
frequency of the CPU faster than allowed by the hardware.
Before the above commit, the default transition delay was set to 200 ms
for a transition_latency of 200000 ns. Lets revert back to that
transition delay value to fix it. Note that several other transition
delay values were tested like 20 ms and 30 ms and none of them have
resolved system hang issue completely.
Fixes: e948bc8fbee0 (cpufreq: Cap the default transition delay value to 10 ms)
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a8b149d32b663c1a4105273295184b78f53d33cf ]
It is possible to remove a cpufreq governor module after
cpufreq_parse_governor() has returned success in
store_scaling_governor() and before cpufreq_set_policy()
acquires a reference to it, because the governor list is
not protected during that period and nothing prevents the
governor from being unregistered then.
Prevent that from happening by acquiring an extra reference
to the governor module temporarily in cpufreq_parse_governor(),
under cpufreq_governor_mutex, and dropping it in
store_scaling_governor(), when cpufreq_set_policy() returns.
Note that the second cpufreq_parse_governor() call site is fine,
because it only cares about the policy member of new_policy.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0373ca74831b0f93cd4cdbf7ad3aec3c33a479a5 upstream.
commit a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b399151cb48db30ad1e0e93dd40d68c6d007b637 upstream.
x86_mask is a confusing name which is hard to associate with the
processor's stepping.
Additionally, correct an indent issue in lib/cpu.c.
Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com>
[ Updated it to more recent kernels. ]
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1514771530-70829-1-git-send-email-qianyue.zj@alibaba-inc.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3fa4680b860bf48b437d6a2c039789c4abe202ae upstream.
Some OpenPOWER boxes can have same pstate values for nominal and
pmin pstates. In these boxes the current code will not initialize
'powernv_pstate_info.min' variable and result in erroneous CPU
frequency reporting. This patch fixes this problem.
Fixes: 09ca4c9b5958 (cpufreq: powernv: Replacing pstate_id with frequency table index)
Reported-by: Alvin Wang <wangat@tw.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6066998cbd2b1012a8d5bc9a2957cfd0ad53150e upstream.
mediatek projects will use mediate-cpufreq.c as cpufreq driver,
instead of using cpufreq_dt.c
Add mediatek related projects into cpufreq-dt blacklist
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0d307935fefa6389eb726c6362351c162c949101 ]
The MIPS loongson cpufreq drivers don't build unless configured for the
correct machine type, due to dependency on machine specific architecture
headers and symbols in machine specific platform code.
More specifically loongson1-cpufreq.c uses RST_CPU_EN and RST_CPU,
neither of which is defined in asm/mach-loongson32/regs-clk.h unless
CONFIG_LOONGSON1_LS1B=y, and loongson2_cpufreq.c references
loongson2_clockmod_table[], which is only defined in
arch/mips/loongson64/lemote-2f/clock.c, i.e. when
CONFIG_LEMOTE_MACH2F=y.
Add these dependencies to Kconfig to avoid randconfig / allyesconfig
build failures (e.g. when based on BMIPS which also has a cpufreq
driver).
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56026645e2b6f11ede34a5e6ab69d3eb56f9c8fc upstream.
After commit aa7519af450d (cpufreq: Use transition_delay_us for legacy
governors as well) the sampling_rate field of struct dbs_data may be
less than the tick period which causes dbs_update() to produce
incorrect results, so make the code ensure that the value of that
field will always be sufficiently large.
Fixes: aa7519af450d (cpufreq: Use transition_delay_us for legacy governors as well)
Reported-by: Andy Tang <andy.tang@nxp.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Andy Tang <andy.tang@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ti-cpufreq and cpufreq-dt-platdev drivers are registering platform-device
with same name "cpufreq-dt" using platform_device_register_*() routines.
This is leading to build warnings appended below.
Providing hardware information to OPP framework along with the platform-
device creation should be done by ti-cpufreq driver before cpufreq-dt
driver comes into place.
This patch add's TI am33xx, am43 and dra7 platforms (which use opp-v2
property) to the blacklist of devices in cpufreq-dt-platform driver to
avoid creating platform-device twice and remove build warnings.
[ 2.370167] ------------[ cut here ]------------
[ 2.375087] WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x58/0x78
[ 2.383112] sysfs: cannot create duplicate filename '/devices/platform/cpufreq-dt'
[ 2.391219] Modules linked in:
[ 2.394506] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.13.0-next-20170912 #1
[ 2.402006] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 2.408437] [<c0110a28>] (unwind_backtrace) from [<c010ca84>] (show_stack+0x10/0x14)
[ 2.416568] [<c010ca84>] (show_stack) from [<c0827d64>] (dump_stack+0xac/0xe0)
[ 2.424165] [<c0827d64>] (dump_stack) from [<c0137470>] (__warn+0xd8/0x104)
[ 2.431488] [<c0137470>] (__warn) from [<c01374d0>] (warn_slowpath_fmt+0x34/0x44)
[ 2.439351] [<c01374d0>] (warn_slowpath_fmt) from [<c03459d0>] (sysfs_warn_dup+0x58/0x78)
[ 2.447938] [<c03459d0>] (sysfs_warn_dup) from [<c0345ab8>] (sysfs_create_dir_ns+0x80/0x98)
[ 2.456719] [<c0345ab8>] (sysfs_create_dir_ns) from [<c082c554>] (kobject_add_internal+0x9c/0x2d4)
[ 2.466124] [<c082c554>] (kobject_add_internal) from [<c082c7d8>] (kobject_add+0x4c/0x9c)
[ 2.474712] [<c082c7d8>] (kobject_add) from [<c05803e4>] (device_add+0xcc/0x57c)
[ 2.482489] [<c05803e4>] (device_add) from [<c0584b74>] (platform_device_add+0x100/0x220)
[ 2.491085] [<c0584b74>] (platform_device_add) from [<c05855a8>] (platform_device_register_full+0xf4/0x118)
[ 2.501305] [<c05855a8>] (platform_device_register_full) from [<c067023c>] (ti_cpufreq_init+0x150/0x22c)
[ 2.511253] [<c067023c>] (ti_cpufreq_init) from [<c0101df4>] (do_one_initcall+0x3c/0x170)
[ 2.519838] [<c0101df4>] (do_one_initcall) from [<c0c00eb4>] (kernel_init_freeable+0x1fc/0x2c4)
[ 2.528974] [<c0c00eb4>] (kernel_init_freeable) from [<c083bcac>] (kernel_init+0x8/0x110)
[ 2.537565] [<c083bcac>] (kernel_init) from [<c0107d18>] (ret_from_fork+0x14/0x3c)
[ 2.545981] ---[ end trace 2fc00e213c13ab20 ]---
[ 2.551051] ------------[ cut here ]------------
[ 2.555931] WARNING: CPU: 0 PID: 1 at lib/kobject.c:240 kobject_add_internal+0x254/0x2d4
[ 2.564578] kobject_add_internal failed for cpufreq-dt with -EEXIST, don't try to register
things with the same name in the same directory.
[ 2.577977] Modules linked in:
[ 2.581261] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.13.0-next-20170912 #1
[ 2.590013] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 2.596437] [<c0110a28>] (unwind_backtrace) from [<c010ca84>] (show_stack+0x10/0x14)
[ 2.604573] [<c010ca84>] (show_stack) from [<c0827d64>] (dump_stack+0xac/0xe0)
[ 2.612172] [<c0827d64>] (dump_stack) from [<c0137470>] (__warn+0xd8/0x104)
[ 2.619494] [<c0137470>] (__warn) from [<c01374d0>] (warn_slowpath_fmt+0x34/0x44)
[ 2.627362] [<c01374d0>] (warn_slowpath_fmt) from [<c082c70c>] (kobject_add_internal+0x254/0x2d4)
[ 2.636666] [<c082c70c>] (kobject_add_internal) from [<c082c7d8>] (kobject_add+0x4c/0x9c)
[ 2.645255] [<c082c7d8>] (kobject_add) from [<c05803e4>] (device_add+0xcc/0x57c)
[ 2.653027] [<c05803e4>] (device_add) from [<c0584b74>] (platform_device_add+0x100/0x220)
[ 2.661615] [<c0584b74>] (platform_device_add) from [<c05855a8>] (platform_device_register_full+0xf4/0x118)
[ 2.671833] [<c05855a8>] (platform_device_register_full) from [<c067023c>] (ti_cpufreq_init+0x150/0x22c)
[ 2.681779] [<c067023c>] (ti_cpufreq_init) from [<c0101df4>] (do_one_initcall+0x3c/0x170)
[ 2.690377] [<c0101df4>] (do_one_initcall) from [<c0c00eb4>] (kernel_init_freeable+0x1fc/0x2c4)
[ 2.699510] [<c0c00eb4>] (kernel_init_freeable) from [<c083bcac>] (kernel_init+0x8/0x110)
[ 2.708106] [<c083bcac>] (kernel_init) from [<c0107d18>] (ret_from_fork+0x14/0x3c)
[ 2.716217] ---[ end trace 2fc00e213c13ab21 ]---
Fixes: edeec420de24 (cpufreq: dt-cpufreq: platdev Automatically create device with OPP v2)
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rather than letting the ti-cpufreq driver match against 'ti,am4372'
machine compatible during probe let's match against 'ti,am43' so that we
can support both 'ti,am4372' and 'ti,am438x' platforms which both match
to this compatible.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit edeec420de24 (cpufreq: dt-platdev: Automatically create cpufreq
device with OPP v2) missed adding few platforms to the blacklist which
create the cpufreq-dt device from their own drivers, after some
dependencies are sorted out.
And for those platforms, both the platform specific driver and the
cpufreq-dt-platdev driver try to create the cpufreq-dt device now.
Fix that by including those platforms in the blacklist. This doesn't include
the TI platforms, for which there is a separate patch.
Fixes: edeec420de24 (cpufreq: dt-cpufreq: platdev Automatically create device with OPP v2)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
Florian Fainelli
Viresh Kumar
John Hubbard
Kai Shen
Bo Yan
Zumeng Chen
Rafael J. Wysocki
Wen Yang
Peter Zijlstra
Erwan Velu
Arnd Bergmann
Yangtao Li
Sudeep Holla
Anson Huang
Henry Willard
Prashanth Prakash
Srinivas Pandruvada
Chen Yu
Tao Wang
Chunyu Hu
Shunyong Yang
Shilpasri G Bhat
George Cherian
Gautham R. Shenoy
Greg Kroah-Hartman
Jia Zhang
Andrew-sh Cheng
James Hogan
Suniel Mahesh
Dave Gerlach
Christoph Hellwig