| Age | Commit message (Collapse) | Author |
|---|
|
commit 965c94f309be58fbcc6c8d3e4f123376c5970d79 upstream.
An ioda_pe for each VF is allocated in pnv_pci_sriov_enable() before
the pci_dev for the VF is created. We need to set the pe->pdev pointer
at some point after the pci_dev is created. Currently we do that in:
pcibios_bus_add_device()
pnv_pci_dma_dev_setup() (via phb->ops.dma_dev_setup)
/* fixup is done here */
pnv_pci_ioda_dma_dev_setup() (via pnv_phb->dma_dev_setup)
The fixup needs to be done before setting up DMA for for the VF's PE,
but there's no real reason to delay it until this point. Move the
fixup into pnv_pci_ioda_fixup_iov() so the ordering is:
pcibios_add_device()
pnv_pci_ioda_fixup_iov() (via ppc_md.pcibios_fixup_sriov)
pcibios_bus_add_device()
...
This isn't strictly required, but it's a slightly more logical place
to do the fixup and it simplifies pnv_pci_dma_dev_setup().
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-4-oohall@gmail.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3b5b9997b331e77ce967eba2c4bc80dc3134a7fe upstream.
On pseries there is a bug with adding hotplugged devices to an IOMMU
group. For a number of dumb reasons fixing that bug first requires
re-working how VFs are configured on PowerNV. For background, on
PowerNV we use the pcibios_sriov_enable() hook to do two things:
1. Create a pci_dn structure for each of the VFs, and
2. Configure the PHB's internal BARs so the MMIO range for each VF
maps to a unique PE.
Roughly speaking a PE is the hardware counterpart to a Linux IOMMU
group since all the devices in a PE share the same IOMMU table. A PE
also defines the set of devices that should be isolated in response to
a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all
MMIO and DMA traffic to and from devicein the PE is blocked by the
root complex until the PE is recovered by the OS.
The requirement to block MMIO causes a giant headache because the P8
PHB generally uses a fixed mapping between MMIO addresses and PEs. As
a result we need to delay configuring the IOMMU groups for device
until after MMIO resources are assigned. For physical devices (i.e.
non-VFs) the PE assignment is done in pcibios_setup_bridge() which is
called immediately after the MMIO resources for downstream
devices (and the bridge's windows) are assigned. For VFs the setup is
more complicated because:
a) pcibios_setup_bridge() is not called again when VFs are activated, and
b) The pci_dev for VFs are created by generic code which runs after
pcibios_sriov_enable() is called.
The work around for this is a two step process:
1. A fixup in pcibios_add_device() is used to initialised the cached
pe_number in pci_dn, then
2. A bus notifier then adds the device to the IOMMU group for the PE
specified in pci_dn->pe_number.
A side effect fixing the pseries bug mentioned in the first paragraph
is moving the fixup out of pcibios_add_device() and into
pcibios_bus_add_device(), which is called much later. This results in
step 2. failing because pci_dn->pe_number won't be initialised when
the bus notifier is run.
We can fix this by removing the need for the fixup. The PE for a VF is
known before the VF is even scanned so we can initialise
pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately,
moving the initialisation causes two problems:
1. We trip the WARN_ON() in the current fixup code, and
2. The EEH core clears pdn->pe_number when recovering a VF and
relies on the fixup to correctly re-set it.
The only justification for either of these is a comment in
eeh_rmv_device() suggesting that pdn->pe_number *must* be set to
IODA_INVALID_PE in order for the VF to be scanned. However, this
comment appears to have no basis in reality. Both bugs can be fixed by
just deleting the code.
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191028085424.12006-1-oohall@gmail.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 9d72dcef891030545f39ad386a30cf91df517fb2 upstream.
On PowerNV the PCIe topology is (currently) managed by the powernv platform
code in Linux in cooperation with the platform firmware. Linux's native
PCIe port service drivers operate independently of both and this can cause
problems.
The main issue is that the portbus driver will conflict with the platform
specific hotplug driver (pnv_php) over ownership of the MSI used to notify
the host when a hotplug event occurs. The portbus driver claims this MSI on
behalf of the individual port services because the same interrupt is used
for hotplug events, PMEs (on root ports), and link bandwidth change
notifications. The portbus driver will always claim the interrupt even if
the individual port service drivers, such as pciehp, are compiled out.
The second, bigger, problem is that the hotplug port service driver
fundamentally does not work on PowerNV. The platform assumes that all
PCI devices have a corresponding arch-specific handle derived from the DT
node for the device (pci_dn) and without one the platform will not allow
a PCI device to be enabled. This problem is largely due to historical
baggage, but it can't be resolved without significant re-factoring of the
platform PCI support.
We can fix these problems in the interim by setting the
"pcie_ports_disabled" flag during platform initialisation. The flag
indicates the platform owns the PCIe ports which stops the portbus driver
from being registered.
This does have the side effect of disabling all port services drivers
that is: AER, PME, BW notifications, hotplug, and DPC. However, this is
not a huge disadvantage on PowerNV since these services are either unused
or handled through other means.
Fixes: 66725152fb9f ("PCI/hotplug: PowerPC PowerNV PCI hotplug driver")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191118065553.30362-1-oohall@gmail.com
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The compound IOMMU group rework moved iommu_register_group() together
in pnv_pci_ioda_setup_iommu_api() (which is a part of
ppc_md.pcibios_fixup). As the result, pnv_ioda_setup_bus_iommu_group()
does not create groups any more, it only adds devices to groups.
This works fine for boot time devices. However IOMMU groups for
SRIOV's VFs were added by pnv_ioda_setup_bus_iommu_group() so this got
broken: pnv_tce_iommu_bus_notifier() expects a group to be registered
for VF and it is not.
This adds missing group registration and adds a NULL pointer check
into the bus notifier so we won't crash if there is no group, although
it is not expected to happen now because of the change above.
Example oops seen prior to this patch:
$ echo 1 > /sys/bus/pci/devices/0000\:01\:00.0/sriov_numvfs
Unable to handle kernel paging request for data at address 0x00000030
Faulting instruction address: 0xc0000000004a6018
Oops: Kernel access of bad area, sig: 11 [#1]
LE SMP NR_CPUS=2048 NUMA PowerNV
CPU: 46 PID: 7006 Comm: bash Not tainted 4.15-ish
NIP: c0000000004a6018 LR: c0000000004a6014 CTR: 0000000000000000
REGS: c000008fc876b400 TRAP: 0300 Not tainted (4.15-ish)
MSR: 900000000280b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE>
CFAR: c000000000d0be20 DAR: 0000000000000030 DSISR: 40000000 SOFTE: 1
...
NIP sysfs_do_create_link_sd.isra.0+0x68/0x150
LR sysfs_do_create_link_sd.isra.0+0x64/0x150
Call Trace:
pci_dev_type+0x0/0x30 (unreliable)
iommu_group_add_device+0x8c/0x600
iommu_add_device+0xe8/0x180
pnv_tce_iommu_bus_notifier+0xb0/0xf0
notifier_call_chain+0x9c/0x110
blocking_notifier_call_chain+0x64/0xa0
device_add+0x524/0x7d0
pci_device_add+0x248/0x450
pci_iov_add_virtfn+0x294/0x3e0
pci_enable_sriov+0x43c/0x580
mlx5_core_sriov_configure+0x15c/0x2f0 [mlx5_core]
sriov_numvfs_store+0x180/0x240
dev_attr_store+0x3c/0x60
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1ac/0x240
__vfs_write+0x3c/0x70
vfs_write+0xd8/0x220
SyS_write+0x6c/0x110
system_call+0x58/0x6c
Fixes: 0bd971676e68 ("powerpc/powernv/npu: Add compound IOMMU groups")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reported-by: Santwana Samantray <santwana.samantray@in.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The powernv platform registers IOMMU groups and adds devices to them
from the pci_controller_ops::setup_bridge() hook except one case when
virtual functions (SRIOV VFs) are added from a bus notifier.
The pseries platform registers IOMMU groups from
the pci_controller_ops::dma_bus_setup() hook and adds devices from
the pci_controller_ops::dma_dev_setup() hook. The very same bus notifier
used for powernv does not add devices for pseries though as
__of_scan_bus() adds devices first, then it does the bus/dev DMA setup.
Both platforms use iommu_add_device() which takes a device and expects
it to have a valid IOMMU table struct with an iommu_table_group pointer
which in turn points the iommu_group struct (which represents
an IOMMU group). Although the helper seems easy to use, it relies on
some pre-existing device configuration and associated data structures
which it does not really need.
This simplifies iommu_add_device() to take the table_group pointer
directly. Pseries already has a table_group pointer handy and the bus
notified is not used anyway. For powernv, this copies the existing bus
notifier, makes it work for powernv only which means an easy way of
getting to the table_group pointer. This was tested on VFs but should
also support physical PCI hotplug.
Since iommu_add_device() receives the table_group pointer directly,
pseries does not do TCE cache invalidation (the hypervisor does) nor
allow multiple groups per a VFIO container (in other words sharing
an IOMMU table between partitionable endpoints), this removes
iommu_table_group_link from pseries.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
CONFIG_PCI_MSI was made mandatory by commit a311e738b6d8
("powerpc/powernv: Make PCI non-optional") so the #ifdef
checks around CONFIG_PCI_MSI here can be removed entirely.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
opal_pci_eeh_freeze_status
The current implementation of the OPAL_PCI_EEH_FREEZE_STATUS call in
skiboot's NPU driver does not touch the pci_error_type parameter so
it might have garbage but the powernv code analyzes it nevertheless.
This initializes pcierr and fstate to zero in all call sites.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Right now we have allocation code in pci-ioda.c and traversing code in
pci.c, let's keep them toghether. However both files are big enough
already so let's move this business to a new file.
While we at it, move the code which links IOMMU table groups to
IOMMU tables as it is not specific to any PNV PHB model.
These puts exported symbols from the new file together.
This fixes several warnings from checkpatch.pl like this:
"WARNING: Prefer 'unsigned int' to bare use of 'unsigned'".
As this is almost cut-n-paste, there should be no behavioral change.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
P9 supports PCI tunneled operations (atomics and as_notify). This
patch adds support for tunneled operations on powernv, with a new
API, to be called by device drivers:
pnv_pci_enable_tunnel()
Enable tunnel operations, tell driver the 16-bit ASN indication
used by kernel.
pnv_pci_disable_tunnel()
Disable tunnel operations.
pnv_pci_set_tunnel_bar()
Tell kernel the Tunnel BAR Response address used by driver.
This function uses two new OPAL calls, as the PBCQ Tunnel BAR
register is configured by skiboot.
pnv_pci_get_as_notify_info()
Return the ASN info of the thread to be woken up.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The NPU was already abstracted by opal as a virtual PHB for nvlink,
but it helps to be able to differentiate between a nvlink or opencapi
PHB, as it's not completely transparent to linux. In particular, PE
assignment differs and we'll also need the information in later
patches.
So rename existing PNV_PHB_NPU type to PNV_PHB_NPU_NVLINK and add a
new type PNV_PHB_NPU_OCAPI.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
P9 has support for PCI peer-to-peer, enabling a device to write in the
MMIO space of another device directly, without interrupting the CPU.
This patch adds support for it on powernv, by adding a new API to be
called by drivers. The pnv_pci_set_p2p(...) call configures an
'initiator', i.e the device which will issue the MMIO operation, and a
'target', i.e. the device on the receiving side.
P9 really only supports MMIO stores for the time being but that's
expected to change in the future, so the API allows to define both
load and store operations.
/* PCI p2p descriptor */
#define OPAL_PCI_P2P_ENABLE 0x1
#define OPAL_PCI_P2P_LOAD 0x2
#define OPAL_PCI_P2P_STORE 0x4
int pnv_pci_set_p2p(struct pci_dev *initiator, struct pci_dev *target,
u64 desc)
It uses a new OPAL call, as the configuration magic is done on the
PHBs by skiboot.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
[mpe: Drop unrelated OPAL calls, s/uint64_t/u64/, minor formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
As with P7IOC and PHB3, add kernel-side support for decoding and printing
diagnostic data for PHB4.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Diagnostic data for PHBs currently works by allocated a fixed-sized buffer.
This is simple, but either wastes memory (though only a few kilobytes) or
in the case of PHB4 isn't enough to fit the whole data blob.
For machines that don't describe the diagnostic data size in the device
tree, use the hardcoded buffer size as before. For those that do, only
allocate exactly what's needed.
In the special case of P7IOC (which has two types of diag data), the larger
should be specified in the device tree.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Dumping the PE State Tables (PEST) can be highly verbose if a number of PEs
are affected, especially in the case where the whole PHB is frozen and 512
lines get printed. Check for duplicates when dumping the PEST to reduce
useless output.
For example:
PE[0f8] A/B: 9700002600000000 80000080d00000f8
PE[0f9] A/B: 8000000000000000 0000000000000000
PE[..0fe] A/B: as above
PE[0ff] A/B: 8440002b00000000 0000000000000000
instead of:
PE[0f8] A/B: 9700002600000000 80000080d00000f8
PE[0f9] A/B: 8000000000000000 0000000000000000
PE[0fa] A/B: 8000000000000000 0000000000000000
PE[0fb] A/B: 8000000000000000 0000000000000000
PE[0fc] A/B: 8000000000000000 0000000000000000
PE[0fd] A/B: 8000000000000000 0000000000000000
PE[0fe] A/B: 8000000000000000 0000000000000000
PE[0ff] A/B: 8440002b00000000 0000000000000000
and you can imagine how much worse it can get for 512 PEs.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pnv_pci_table_alloc() ignores possible failure from kzalloc_node(),
this adds a check. There are 2 callers of pnv_pci_table_alloc(),
one already checks for tbl!=NULL, this adds WARN_ON() to the other path
which only happens during boot time in IODA1 and not expected to fail.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Merge the topic branch we were sharing with kvm-ppc, Paul has also
merged it.
|
|
So far iommu_table obejcts were only used in virtual mode and had
a single owner. We are going to change this by implementing in-kernel
acceleration of DMA mapping requests. The proposed acceleration
will handle requests in real mode and KVM will keep references to tables.
This adds a kref to iommu_table and defines new helpers to update it.
This replaces iommu_free_table() with iommu_tce_table_put() and makes
iommu_free_table() static. iommu_tce_table_get() is not used in this patch
but it will be in the following patch.
Since this touches prototypes, this also removes @node_name parameter as
it has never been really useful on powernv and carrying it for
the pseries platform code to iommu_free_table() seems to be quite
useless as well.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The iommu_table_ops callbacks are declared CPU endian as they take and
return "unsigned long"; underlying hardware tables are big-endian.
However get() was missing be64_to_cpu(), this adds the missing conversion.
The only caller of this is crash dump at arch/powerpc/kernel/iommu.c,
iommu_table_clear() which only compares TCE to zero so this change
should not cause behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add detection of NPU2 PHBs. NPU2/NVLink2 has a different register
layout for the TCE kill register therefore TCE invalidation should be
done via the OPAL call rather than using the register directly as it
is for PHB3 and NVLink1. This changes TCE invalidation to use the OPAL
call in the case of a NPU2 PHB model.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This fixes the warnings reported from sparse:
pci.c:312:33: warning: restricted __be64 degrades to integer
pci.c:313:33: warning: restricted __be64 degrades to integer
Fixes: cee72d5bb489 ("powerpc/powernv: Display diag data on p7ioc EEH errors")
Cc: stable@vger.kernel.org # v3.3+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
NO_IRQ has been == 0 on powerpc for just over ten years (since commit
0ebfff1491ef ("[POWERPC] Add new interrupt mapping core and change
platforms to use it")). It's also 0 on most other arches.
Although it's fairly harmless, every now and then it causes confusion
when a driver is built on powerpc and another arch which doesn't define
NO_IRQ. There's at least 6 definitions of NO_IRQ in drivers/, at least
some of which are to work around that problem.
So we'd like to remove it. This is fairly trivial in the arch code, we
just convert:
if (irq == NO_IRQ) to if (!irq)
if (irq != NO_IRQ) to if (irq)
irq = NO_IRQ; to irq = 0;
return NO_IRQ; to return 0;
And a few other odd cases as well.
At least for now we keep the #define NO_IRQ, because there is driver
code that uses NO_IRQ and the fixes to remove those will go via other
trees.
Note we also change some occurrences in PPC sound drivers, drivers/ps3,
and drivers/macintosh.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The iommu_table_ops::exchange() callback writes new TCE to the table and
returns old value and permission mask. The old TCE value is correctly
converted from BE to CPU endian; however permission mask was calculated
from BE value and therefore always returned DMA_NONE which could cause
memory leak on LE systems using VFIO SPAPR TCE IOMMU v1 driver.
This fixes pnv_tce_xchg() to have @oldtce a CPU endian.
Fixes: 05c6cfb9dce0 ("powerpc/iommu/powernv: Release replaced TCE")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We instanciate them as IODA2. We also change the MSI EOI hack
to only kick on PHB3 since it will not be needed on any new
implementation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This exports 4 functions, which base on the corresponding OPAL
APIs to get/set PCI slot status. Those functions are going to
be used by PowerNV PCI hotplug driver:
pnv_pci_get_device_tree() opal_get_device_tree()
pnv_pci_get_presence_state() opal_pci_get_presence_state()
pnv_pci_get_power_state() opal_pci_get_power_state()
pnv_pci_set_power_state() opal_pci_set_power_state()
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This introduces pnv_pci_get_slot_id() to get the hotpluggable PCI
slot ID from the corresponding device node. It will be used by
hotplug driver.
Requested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pdn (struct pci_dn) instances are allocated from memblock or
bootmem when creating PCI controller (hoses) in setup_arch(). PCI
hotplug, which will be supported by proceeding patches, releases
PCI device nodes and their corresponding pdn on unplugging event.
The memory chunks for pdn instances allocated from memblock or
bootmem are hard to reused after being released.
This delays creating pdn by pci_devs_phb_init() from setup_arch()
to core_initcall() so that they are allocated from slab. The memory
consumed by pdn can be released to system without problem during
PCI unplugging time. It indicates that pci_dn is unavailable in
setup_arch() and the the fixup on pdn (like AGP's) can't be carried
out that time. We have to do that in pcibios_root_bridge_prepare()
on maple/pasemi/powermac platforms where/when the pdn is available.
pcibios_root_bridge_prepare is called from subsys_initcall() which
is executed after core_initcall() so the code flow does not change.
At the mean while, the EEH device is created when pdn is populated,
meaning pdn and EEH device have same life cycle. In turn, we needn't
call eeh_dev_init() to create EEH device explicitly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The macro defined in arch/powerpc/platforms/powernv/pci.c isn't
used by anyone. Just remove it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This changes the data type of PE number from "int" to "unsigned int"
in order to match the fact PE number is never negative:
* The number of PE to which the specified PCI device is attached.
* The PE number map for SRIOV VFs.
* The returned PE number from pnv_ioda_alloc_pe().
* The returned PE number from pnv_ioda2_pick_m64_pe().
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This renames the fields related to PE number in "struct pnv_phb"
for better reflecting of their usages as Alexey suggested. No
logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When cfg_dbg() is enabled (i.e. mapped to printk()), gcc produces
errors as the __func__ parameter is missing (pnv_pci_cfg_read() has one);
this adds the missing parameter.
cfg_dbg() is just an inferior version of pr_devel() so use the latter
instead.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Pull in our current fixes from 4.5, in particular the "Fix Multi hit
ERAT" bug is causing folks some grief when testing next.
|
|
Quite often drivers set only "write" permission assuming that this
includes "read" permission as well and this works on plenty of
platforms. However IODA2 is strict about this and produces an EEH when
"read" permission is not set and reading happens.
This adds a workaround in the IODA code to always add the "read" bit
when the "write" bit is set.
Fixes: 10b35b2b7485 ("powerpc/powernv: Do not set "read" flag if direction==DMA_NONE")
Cc: stable@vger.kernel.org # 4.2+
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When PCI bus is unplugged during full hotplug for EEH recovery,
the platform PE instance (struct pnv_ioda_pe) isn't released and
it dereferences the stale PCI bus that has been released. It leads
to kernel crash when referring to the stale PCI bus.
This fixes the issue by correcting the PE's primary bus when it's
oneline at plugging time, in pnv_pci_dma_bus_setup() which is to
be called by pcibios_fixup_bus().
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
"p5ioc2 is used by approximately 2 machines in the world, and has never
ever been a supported configuration."
The code for p5ioc2 is essentially unused and complicates what is already
a very complicated codebase. Its removal is essentially a "free win" in
the effort to simplify the powernv PCI code.
In addition, support for p5ioc2 has been dropped from skiboot. There's no
reason to keep it around in the kernel.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PCI in powernv now supports quite a bit more than p5ioc2, so remove the
outdated comment.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
NVLink is a high speed interconnect that is used in conjunction with a
PCI-E connection to create an interface between CPU and GPU that
provides very high data bandwidth. A PCI-E connection to a GPU is used
as the control path to initiate and report status of large data
transfers sent via the NVLink.
On IBM Power systems the NVLink processing unit (NPU) is similar to
the existing PHB3. This patch adds support for a new NPU PHB type. DMA
operations on the NPU are not supported as this patch sets the TCE
translation tables to be the same as the related GPU PCIe device for
each NVLink. Therefore all DMA operations are setup and controlled via
the PCIe device.
EEH is not presently supported for the NPU devices, although it may be
added in future.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This fixes a race which can result in the same virtual IRQ number
being assigned to two different MSI interrupts. The most visible
consequence of that is usually a warning and stack trace from the
sysfs code about an attempt to create a duplicate entry in sysfs.
The race happens when one CPU (say CPU 0) is disposing of an MSI
while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls
(for example) pnv_teardown_msi_irqs(), which calls
msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its
hardware IRQ number) is no longer in use. Then, before CPU 0 gets
to calling irq_dispose_mapping() to free up the virtal IRQ number,
CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an
MSI, and gets the same hardware IRQ number that CPU 0 just freed.
CPU 1 then calls irq_create_mapping() to get a virtual IRQ number,
which sees that there is currently a mapping for that hardware IRQ
number and returns the corresponding virtual IRQ number (which is
the same virtual IRQ number that CPU 0 was using). CPU 0 then
calls irq_dispose_mapping() and frees that virtual IRQ number.
Now, if another CPU comes along and calls irq_create_mapping(), it
is likely to get the virtual IRQ number that was just freed,
resulting in the same virtual IRQ number apparently being used for
two different hardware interrupts.
To fix this race, we just move the call to msi_bitmap_free_hwirqs()
to after the call to irq_dispose_mapping(). Since virq_to_hw()
doesn't work for the virtual IRQ number after irq_dispose_mapping()
has been called, we need to call it before irq_dispose_mapping() and
remember the result for the msi_bitmap_free_hwirqs() call.
The pattern of calling msi_bitmap_free_hwirqs() before
irq_dispose_mapping() appears in 5 places under arch/powerpc, and
appears to have originated in commit 05af7bd2d75e ("[POWERPC] MPIC
U3/U4 MSI backend") from 2007.
Fixes: 05af7bd2d75e ("[POWERPC] MPIC U3/U4 MSI backend")
Cc: stable@vger.kernel.org # v2.6.22+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
|
|
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit 763d2d8df1ee ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Use accessor for_each_pci_msi_entry() to access MSI device list, so we
could easily move msi_list from struct pci_dev into struct device
later.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Olof Johansson <olof@lixom.net>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Wei Yang <weiyang@linux.vnet.ibm.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Tudor Laurentiu <b10716@freescale.com>
Cc: Hongtao Jia <hongtao.jia@freescale.com>
Link: http://lkml.kernel.org/r/1436428847-8886-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
TCE tables might get too big in case of 4K IOMMU pages and DDW enabled
on huge guests (hundreds of GB of RAM) so the kernel might be unable to
allocate contiguous chunk of physical memory to store the TCE table.
To address this, POWER8 CPU (actually, IODA2) supports multi-level
TCE tables, up to 5 levels which splits the table into a tree of
smaller subtables.
This adds multi-level TCE tables support to
pnv_pci_ioda2_table_alloc_pages() and pnv_pci_ioda2_table_free_pages()
helpers.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
At the moment writing new TCE value to the IOMMU table fails with EBUSY
if there is a valid entry already. However PAPR specification allows
the guest to write new TCE value without clearing it first.
Another problem this patch is addressing is the use of pool locks for
external IOMMU users such as VFIO. The pool locks are to protect
DMA page allocator rather than entries and since the host kernel does
not control what pages are in use, there is no point in pool locks and
exchange()+put_page(oldtce) is sufficient to avoid possible races.
This adds an exchange() callback to iommu_table_ops which does the same
thing as set() plus it returns replaced TCE and DMA direction so
the caller can release the pages afterwards. The exchange() receives
a physical address unlike set() which receives linear mapping address;
and returns a physical address as the clear() does.
This implements exchange() for P5IOC2/IODA/IODA2. This adds a requirement
for a platform to have exchange() implemented in order to support VFIO.
This replaces iommu_tce_build() and iommu_clear_tce() with
a single iommu_tce_xchg().
This makes sure that TCE permission bits are not set in TCE passed to
IOMMU API as those are to be calculated by platform code from
DMA direction.
This moves SetPageDirty() to the IOMMU code to make it work for both
VFIO ioctl interface in in-kernel TCE acceleration (when it becomes
available later).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This replaces direct accesses to TCE table with a helper which
returns an TCE entry address. This does not make difference now but will
when multi-level TCE tables get introduces.
No change in behavior is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
So far one TCE table could only be used by one IOMMU group. However
IODA2 hardware allows programming the same TCE table address to
multiple PE allowing sharing tables.
This replaces a single pointer to a group in a iommu_table struct
with a linked list of groups which provides the way of invalidating
TCE cache for every PE when an actual TCE table is updated. This adds
pnv_pci_link_table_and_group() and pnv_pci_unlink_table_and_group()
helpers to manage the list. However without VFIO, it is still going
to be a single IOMMU group per iommu_table.
This changes iommu_add_device() to add a device to a first group
from the group list of a table as it is only called from the platform
init code or PCI bus notifier and at these moments there is only
one group per table.
This does not change TCE invalidation code to loop through all
attached groups in order to simplify this patch and because
it is not really needed in most cases. IODA2 is fixed in a later
patch.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pnv_pci_ioda_tce_invalidate() helper invalidates TCE cache. It is
supposed to be called on IODA1/2 and not called on p5ioc2. It receives
start and end host addresses of TCE table.
IODA2 actually needs PCI addresses to invalidate the cache. Those
can be calculated from host addresses but since we are going
to implement multi-level TCE tables, calculating PCI address from
a host address might get either tricky or ugly as TCE table remains flat
on PCI bus but not in RAM.
This moves pnv_pci_ioda_tce_invalidate() from generic pnv_tce_build/
pnt_tce_free and defines IODA1/2-specific callbacks which call generic
ones and do PHB-model-specific TCE cache invalidation. P5IOC2 keeps
using generic callbacks as before.
This changes pnv_pci_ioda2_tce_invalidate() to receives TCE index and
number of pages which are PCI addresses shifted by IOMMU page shift.
No change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds a iommu_table_ops struct and puts pointer to it into
the iommu_table struct. This moves tce_build/tce_free/tce_get/tce_flush
callbacks from ppc_md to the new struct where they really belong to.
This adds the requirement for @it_ops to be initialized before calling
iommu_init_table() to make sure that we do not leave any IOMMU table
with iommu_table_ops uninitialized. This is not a parameter of
iommu_init_table() though as there will be cases when iommu_init_table()
will not be called on TCE tables, for example - VFIO.
This does s/tce_build/set/, s/tce_free/clear/ and removes "tce_"
redundant prefixes.
This removes tce_xxx_rm handlers from ppc_md but does not add
them to iommu_table_ops as this will be done later if we decide to
support TCE hypercalls in real mode. This removes _vm callbacks as
only virtual mode is supported by now so this also removes @rm parameter.
For pSeries, this always uses tce_buildmulti_pSeriesLP/
tce_buildmulti_pSeriesLP. This changes multi callback to fall back to
tce_build_pSeriesLP/tce_free_pSeriesLP if FW_FEATURE_MULTITCE is not
present. The reason for this is we still have to support "multitce=off"
boot parameter in disable_multitce() and we do not want to walk through
all IOMMU tables in the system and replace "multi" callbacks with single
ones.
For powernv, this defines _ops per PHB type which are P5IOC2/IODA1/IODA2.
This makes the callbacks for them public. Later patches will extend
callbacks for IODA1/2.
No change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Normally a bitmap from the iommu_table is used to track what TCE entry
is in use. Since we are going to use iommu_table without its locks and
do xchg() instead, it becomes essential not to put bits which are not
implied in the direction flag as the old TCE value (more precisely -
the permission bits) will be used to decide whether to put the page or not.
This adds iommu_direction_to_tce_perm() (its counterpart is there already)
and uses it for powernv's pnv_tce_build().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
Oliver O'Halloran
Thomas Gleixner
Alexey Kardashevskiy
Philippe Bergheaud
Frederic Barrat
Russell Currey
Michael Ellerman
Alistair Popple
Gavin Shan
Krzysztof Kozlowski
Benjamin Herrenschmidt
Paul Mackerras
Linus Torvalds
Andrew Donnellan
Jiang Liu