| Age | Commit message (Collapse) | Author |
|---|
|
native_hpte_clear() is called in real mode from two places:
- Early in boot during htab initialisation if firmware assisted dump is
active.
- Late in the kexec path.
In both contexts there is no need to disable interrupts are they are
already disabled. Furthermore, locking around the tlbie() is only required
for pre POWER5 hardware.
On POWER5 or newer hardware concurrent tlbie()s work as expected and on pre
POWER5 hardware concurrent tlbie()s could result in deadlock. This code
would only be executed at crashdump time, during which all bets are off,
concurrent tlbie()s are unlikely and taking locks is unsafe therefore the
best course of action is to simply do nothing. Concurrent tlbie()s are not
possible in the first case as secondary CPUs have not come up yet.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from
Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change
from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper
from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from
Christophe
* tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc32: memset: only use dcbz once cache is enabled
powerpc32: memcpy: only use dcbz once cache is enabled
powerpc/mm: Recompute hash value after a failed update
powerpc/boot: Specify ABI v2 when building an LE boot wrapper
cxl: Fix build failure due to -Wunused-variable behaviour change
cxl: Fix unbalanced pci_dev_get in cxl_probe
powerpc/MSI: Fix race condition in tearing down MSI interrupts
powerpc: Wire up sys_userfaultfd()
powerpc/pseries: Release DRC when configure_connector fails
cxl: abort cxl_pci_enable_device_hook() if PCI channel is offline
powerpc/powernv/pci-ioda: fix kdump with non-power-of-2 crashkernel=
powerpc/powernv/pci-ioda: fix 32-bit TCE table init in kdump kernel
|
|
If we had secondary hash flag set, we ended up modifying hash value in
the updatepp code path. Hence with a failed updatepp we will be using
a wrong hash value for the following hash insert. Fix this by
recomputing hash before insert.
Without this patch we can end up with using wrong slot number in linux
pte. That can result in us missing an hash pte update or invalidate
which can cause memory corruption or even machine check.
Fixes: 6d492ecc6489 ("powerpc/THP: Add code to handle HPTE faults for hugepages")
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
|
|
While pmem is usable as a block device or via DAX mappings to userspace
there are several usage scenarios that can not target pmem due to its
lack of struct page coverage. In preparation for "hot plugging" pmem
into the vmemmap add ZONE_DEVICE as a new zone to tag these pages
separately from the ones that are subject to standard page allocations.
Importantly "device memory" can be removed at will by userspace
unbinding the driver of the device.
Having a separate zone prevents allocation and otherwise marks these
pages that are distinct from typical uniform memory. Device memory has
different lifetime and performance characteristics than RAM. However,
since we have run out of ZONES_SHIFT bits this functionality currently
depends on sacrificing ZONE_DMA.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Jerome Glisse <j.glisse@gmail.com>
[hch: various simplifications in the arch interface]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux into next
Freescale updates from Scott:
"Highlights include 32-bit memcpy/memset optimizations, checksum
optimizations, 85xx config fragments and updates, device tree updates,
e6500 fixes for non-SMP, and misc cleanup and minor fixes."
|
|
In some situations, a NUMA guest that supports
ibm,dynamic-memory-reconfiguration node will end up having flat NUMA
distances between nodes. This is because of two problems in the
current code.
1) Different representations of associativity lists.
There is an assumption about the associativity list in
initialize_distance_lookup_table(). Associativity list has two forms:
a) [cpu,memory]@x/ibm,associativity has following
format:
<N> <N integers>
b) ibm,dynamic-reconfiguration-memory/ibm,associativity-lookup-arrays
<M> <N> <M associativity lists each having N integers>
M = the number of associativity lists
N = the number of entries per associativity list
Fix initialize_distance_lookup_table() so that it does not assume
"case a". And update the caller to skip the length field before
sending the associativity list.
2) Distance table not getting updated from drconf path.
Node distance table will not get initialized in certain cases as
ibm,dynamic-reconfiguration-memory path does not initialize the
lookup table.
Call initialize_distance_lookup_table() from drconf path with
appropriate associativity list.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The relation between CONFIG_PPC_HAS_HASH_64K and CONFIG_PPC_64K_PAGES is
painfully complicated.
But if we rearrange it enough we can see that PPC_HAS_HASH_64K
essentially depends on PPC_STD_MMU_64 && PPC_64K_PAGES.
We can then notice that PPC_HAS_HASH_64K is used in files that are only
built for PPC_STD_MMU_64, meaning it's equivalent to PPC_64K_PAGES.
So replace all uses and drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
|
|
Back in the olden days we added support for using 64K pages to map the
SPU (Synergistic Processing Unit) local store on Cell, when the main
kernel was using 4K pages.
This was useful at the time because distros were using 4K pages, but
using 64K pages on the SPUs could reduce TLB pressure there.
However these days the number of Cell users is approaching zero, and
supporting this option adds unpleasant complexity to the memory
management code.
So drop the option, CONFIG_SPU_FS_64K_LS, and all related code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
|
|
It makes no sense to put the instructions for calculating the lock
value (cpu number + 1) and the clearing of eq bit of cr1 in lbarx/stbcx
loop. And when the lock is acquired by the other thread, the current
lock value has no chance to equal with the lock value used by current
cpu. So we can skip the comparing for these two lock values in the
lbz/bne loop.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This patch adds some documentation to patch_slb_encoding() explaining
how it works.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Update change log and mention the signedness of the immediate]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The SLB code uses 'slot' and 'entry' interchangeably, change it to always
use 'entry'.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch just removes one redundant entry for one extern variable
'slb_compare_rr_to_size' from the scope. This patch does not change
any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In CoreNet systems it is not allowed to mix M and non-M mappings to the
same memory, and coherent DMA accesses are considered to be M mappings
for this purpose. Ignoring this has been observed to cause hard
lockups in non-SMP kernels on e6500.
Furthermore, e6500 implements the LRAT (logical to real address table)
which allows KVM guests to control the WIMGE bits. This means that
KVM cannot force the M bit on the way it usually does, so the guest had
better set it itself.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
map_kernel() doesn't catch all places that create kernel PTEs. In
particular, vmalloc() calls set_pte_at() directly. This causes a
crash when booting a non-SMP kernel on e6500.
Move the sync to __set_pte(), to be executed only for kernel addresses.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
__flush_dcache_icache_phys() requires the ability to access the
memory with the MMU disabled, which means that on a 32-bit system
any memory above 4 GiB is inaccessible. In particular, mpc86xx is
32-bit and can have more than 4 GiB of RAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
If we take an alignment exception which we cannot fix, the oops
currently prints:
Unable to handle kernel paging request for unknown fault
Lets print something more useful:
Unable to handle kernel paging request for unaligned access at address 0xc0000000f77bba8f
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part two from Paul Gortmaker:
"Replace module_init with appropriate alternate initcall in non
modules.
This series converts non-modular code that is using the module_init()
call to hook itself into the system to instead use one of our
alternate priority initcalls.
Unlike the previous series that used device_initcall and hence was a
runtime no-op, these commits change to one of the alternate initcalls,
because (a) we have them and (b) it seems like the right thing to do.
For example, it would seem logical to use arch_initcall for arch
specific setup code and fs_initcall for filesystem setup code.
This does mean however, that changes in the init ordering will be
taking place, and so there is a small risk that some kind of implicit
init ordering issue may lie uncovered. But I think it is still better
to give these ones sensible priorities than to just assign them all to
device_initcall in order to exactly preserve the old ordering.
Thad said, we have already made similar changes in core kernel code in
commit c96d6660dc65 ("kernel: audit/fix non-modular users of
module_init in core code") without any regressions reported, so this
type of change isn't without precedent. It has also got the same
local testing and linux-next coverage as all the other pull requests
that I'm sending for this merge window have got.
Once again, there is an unused module_exit function removal that shows
up as an outlier upon casual inspection of the diffstat"
* tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
x86: perf_event_intel_pt.c: use arch_initcall to hook in enabling
x86: perf_event_intel_bts.c: use arch_initcall to hook in enabling
mm/page_owner.c: use late_initcall to hook in enabling
lib/list_sort: use late_initcall to hook in self tests
arm: use subsys_initcall in non-modular pl320 IPC code
powerpc: don't use module_init for non-modular core hugetlb code
powerpc: use subsys_initcall for Freescale Local Bus
x86: don't use module_init for non-modular core bootflag code
netfilter: don't use module_init/exit in core IPV4 code
fs/notify: don't use module_init for non-modular inotify_user code
mm: replace module_init usages with subsys_initcall in nommu.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core / firmware changes for 4.2-rc1.
A number of small changes all over the place in the driver core, and
in the firmware subsystem. Nothing really major, full details in the
shortlog. Some of it is a bit of churn, given that the platform
driver probing changes was found to not work well, so they were
reverted.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
Revert "base/platform: Only insert MEM and IO resources"
Revert "base/platform: Continue on insert_resource() error"
Revert "of/platform: Use platform_device interface"
Revert "base/platform: Remove code duplication"
firmware: add missing kfree for work on async call
fs: sysfs: don't pass count == 0 to bin file readers
base:dd - Fix for typo in comment to function driver_deferred_probe_trigger().
base/platform: Remove code duplication
of/platform: Use platform_device interface
base/platform: Continue on insert_resource() error
base/platform: Only insert MEM and IO resources
firmware: use const for remaining firmware names
firmware: fix possible use after free on name on asynchronous request
firmware: check for file truncation on direct firmware loading
firmware: fix __getname() missing failure check
drivers: of/base: move of_init to driver_init
drivers/base: cacheinfo: fix annoying typo when DT nodes are absent
sysfs: disambiguate between "error code" and "failure" in comments
driver-core: fix build for !CONFIG_MODULES
driver-core: make __device_attach() static
...
|
|
We have confusing functions to clear pmd, pmd_clear_* and pmd_clear. Add
_huge_ to pmdp_clear functions so that we are clear that they operate on
hugepage pte.
We don't bother about other functions like pmdp_set_wrprotect,
pmdp_clear_flush_young, because they operate on PTE bits and hence
indicate they are operating on hugepage ptes
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Also move the pmd_trans_huge check to generic code.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Architectures like ppc64 [1] need to do special things while clearing pmd
before a collapse. For them this operation is largely different from a
normal hugepage pte clear. Hence add a separate function to clear pmd
before collapse. After this patch pmdp_* functions operate only on
hugepage pte, and not on regular pmd_t values pointing to page table.
[1] ppc64 needs to invalidate all the normal page pte mappings we already
have inserted in the hardware hash page table. But before doing that we
need to make sure there are no parallel hash page table insert going on.
So we need to do a kick_all_cpus_sync() before flushing the older hash
table entries. By moving this to a separate function we capture these
details and mention how it is different from a hugepage pte clear.
This patch is a cleanup and only does code movement for clarity. There
should not be any change in functionality.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently we have many duplicates in definitions of huge_pmd_unshare. In
all architectures this function just returns 0 when
CONFIG_ARCH_WANT_HUGE_PMD_SHARE is N.
This patch puts the default implementation in mm/hugetlb.c and lets these
architectures use the common code.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Rientjes <rientjes@google.com>
Cc: James Yang <James.Yang@freescale.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux into next
Freescale updates from Scott:
"Highlights include more 8xx optimizations, an e6500 hugetlb optimization,
QMan device tree nodes, t1024/t1023 support, and various fixes and
cleanup."
|
|
The hugetlbpage.o is obj-y (always built in). It will never
be modular, so using module_init as an alias for __initcall is
somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of arch_initcall (which
makes sense for arch code) will thus change this registration
from level 6-device to level 3-arch (i.e. slightly earlier).
However no observable impact of that small difference has
been observed during testing, or is expected.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
We are adding support for DMA memory pre-registration to be used in
conjunction with VFIO. The idea is that the userspace which is going to
run a guest may want to pre-register a user space memory region so
it all gets pinned once and never goes away. Having this done,
a hypervisor will not have to pin/unpin pages on every DMA map/unmap
request. This is going to help with multiple pinning of the same memory.
Another use of it is in-kernel real mode (mmu off) acceleration of
DMA requests where real time translation of guest physical to host
physical addresses is non-trivial and may fail as linux ptes may be
temporarily invalid. Also, having cached host physical addresses
(compared to just pinning at the start and then walking the page table
again on every H_PUT_TCE), we can be sure that the addresses which we put
into TCE table are the ones we already pinned.
This adds a list of memory regions to mm_context_t. Each region consists
of a header and a list of physical addresses. This adds API to:
1. register/unregister memory regions;
2. do final cleanup (which puts all pre-registered pages);
3. do userspace to physical address translation;
4. manage usage counters; multiple registration of the same memory
is allowed (once per container).
This implements 2 counters per registered memory region:
- @mapped: incremented on every DMA mapping; decremented on unmapping;
initialized to 1 when a region is just registered; once it becomes zero,
no more mappings allowe;
- @used: incremented on every "register" ioctl; decremented on
"unregister"; unregistration is allowed for DMA mapped regions unless
it is the very last reference. For the very last reference this checks
that the region is still mapped and returns -EBUSY so the userspace
gets to know that memory is still pinned and unregistration needs to
be retried; @used remains 1.
Host physical addresses are stored in vmalloc'ed array. In order to
access these in the real mode (mmu off), there is a real_vmalloc_addr()
helper. In-kernel acceleration patchset will move it from KVM to MMU code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This enables us to understand how many hash fault we are taking
when running benchmarks.
For ex:
-bash-4.2# ./perf stat -e powerpc:hash_fault -e page-faults /tmp/ebizzy.ppc64 -S 30 -P -n 1000
...
Performance counter stats for '/tmp/ebizzy.ppc64 -S 30 -P -n 1000':
1,10,04,075 powerpc:hash_fault
1,10,03,429 page-faults
30.865978991 seconds time elapsed
NOTE:
The impact of the tracepoint was not noticeable when running test. It was
within the run-time variance of the test. For ex:
without-patch:
--------------
Performance counter stats for './a.out 3000 300':
643 page-faults # 0.089 M/sec
7.236562 task-clock (msec) # 0.928 CPUs utilized
2,179,213 stalled-cycles-frontend # 0.00% frontend cycles idle
17,174,367 stalled-cycles-backend # 0.00% backend cycles idle
0 context-switches # 0.000 K/sec
0.007794658 seconds time elapsed
And with-patch:
---------------
Performance counter stats for './a.out 3000 300':
643 page-faults # 0.089 M/sec
7.233746 task-clock (msec) # 0.921 CPUs utilized
0 context-switches # 0.000 K/sec
0.007854876 seconds time elapsed
Performance counter stats for './a.out 3000 300':
643 page-faults # 0.087 M/sec
649 powerpc:hash_fault # 0.087 M/sec
7.430376 task-clock (msec) # 0.938 CPUs utilized
2,347,174 stalled-cycles-frontend # 0.00% frontend cycles idle
17,524,282 stalled-cycles-backend # 0.00% backend cycles idle
0 context-switches # 0.000 K/sec
0.007920284 seconds time elapsed
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We want the fixes in this branch as well for testing and merge
resolution.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This moves the current include file from cxl.h -> cxl-base.h. This current
include file is used only to pass information between the base driver that
needs to be built into the kernel and the cxl module.
This is to make way for a new include/misc/cxl.h which will
contain just the kernel API for other driver to use
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This fixes calculating the key bits (KP and KS) in the SLB VSID for kernel
mappings.
I'm not CCing this to stable as there are no uses of this currently.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This function can run on systems where physical addresses don't
fit in unsigned long, so make sure to use the macro that contains the
proper cast.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Some workloads take a lot of TLB misses despite using traditional
hugepages. Handle these TLB misses in the asm fastpath rather than
going through a bunch of C code. With this patch I measured around a
5x speedup in handling hugepage TLB misses.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Conflicts:
arch/sparc/include/asm/topology_64.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If both STRICT_MM_TYPECHECKS and DEBUG_PAGEALLOC are enabled, the code
in kernel_map_linear_page() is built, and so we fail with:
arch/powerpc/mm/hash_utils_64.c:1478:2:
error: incompatible type for argument 1 of 'htab_convert_pte_flags'
Fix it by using pgprot_val().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Rename topology_thread_cpumask() to topology_sibling_cpumask()
for more consistency with scheduler code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/1432645896-12588-2-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This adds an extra argument onto parse_params() to be used
as a way to make the unused callback a bit more useful and
generic by allowing the caller to pass on a data structure
of its choice. An example use case is to allow us to easily
make module parameters for every module which we will do
next.
@ parse @
identifier name, args, params, num, level_min, level_max;
identifier unknown, param, val, doing;
type s16;
@@
extern char *parse_args(const char *name,
char *args,
const struct kernel_param *params,
unsigned num,
s16 level_min,
s16 level_max,
+ void *arg,
int (*unknown)(char *param, char *val,
const char *doing
+ , void *arg
));
@ parse_mod @
identifier name, args, params, num, level_min, level_max;
identifier unknown, param, val, doing;
type s16;
@@
char *parse_args(const char *name,
char *args,
const struct kernel_param *params,
unsigned num,
s16 level_min,
s16 level_max,
+ void *arg,
int (*unknown)(char *param, char *val,
const char *doing
+ , void *arg
))
{
...
}
@ parse_args_found @
expression R, E1, E2, E3, E4, E5, E6;
identifier func;
@@
(
R =
parse_args(E1, E2, E3, E4, E5, E6,
+ NULL,
func);
|
R =
parse_args(E1, E2, E3, E4, E5, E6,
+ NULL,
&func);
|
R =
parse_args(E1, E2, E3, E4, E5, E6,
+ NULL,
NULL);
|
parse_args(E1, E2, E3, E4, E5, E6,
+ NULL,
func);
|
parse_args(E1, E2, E3, E4, E5, E6,
+ NULL,
&func);
|
parse_args(E1, E2, E3, E4, E5, E6,
+ NULL,
NULL);
)
@ parse_args_unused depends on parse_args_found @
identifier parse_args_found.func;
@@
int func(char *param, char *val, const char *unused
+ , void *arg
)
{
...
}
@ mod_unused depends on parse_args_found @
identifier parse_args_found.func;
expression A1, A2, A3;
@@
- func(A1, A2, A3);
+ func(A1, A2, A3, NULL);
Generated-by: Coccinelle SmPL
Cc: cocci@systeme.lip6.fr
Cc: Tejun Heo <tj@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Ewan Milne <emilne@redhat.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
the handler
Introduce faulthandler_disabled() and use it to check for irq context and
disabled pagefaults (via pagefault_disable()) in the pagefault handlers.
Please note that we keep the in_atomic() checks in place - to detect
whether in irq context (in which case preemption is always properly
disabled).
In contrast, preempt_disable() should never be used to disable pagefaults.
With !CONFIG_PREEMPT_COUNT, preempt_disable() doesn't modify the preempt
counter, and therefore the result of in_atomic() differs.
We validate that condition by using might_fault() checks when calling
might_sleep().
Therefore, add a comment to faulthandler_disabled(), describing why this
is needed.
faulthandler_disabled() and pagefault_disable() are defined in
linux/uaccess.h, so let's properly add that include to all relevant files.
This patch is based on a patch from Thomas Gleixner.
Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-7-git-send-email-dahi@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The existing code relies on pagefault_disable() implicitly disabling
preemption, so that no schedule will happen between kmap_atomic() and
kunmap_atomic().
Let's make this explicit, to prepare for pagefault_disable() not
touching preemption anymore.
Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-5-git-send-email-dahi@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We need to check whether pte is present in follow_huge_addr() and
properly return NULL if mapping is not present. Also use READ_ONCE
when dereferencing pte_t address.
Without this patch, we may wrongly return a zero pfn page in
follow_huge_addr().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Serialize against find_linux_pte_or_hugepte() which does lock-less
lookup in page tables with local interrupts disabled. For huge pages it
casts pmd_t to pte_t. Since the format of pte_t is different from pmd_t
we want to prevent transit from pmd pointing to page table to pmd
pointing to huge page (and back) while interrupts are disabled. We
clear pmd to possibly replace it with page table pointer in different
code paths. So make sure we wait for the parallel
find_linux_pte_or_hugepage() to finish.
Without this patch, a find_linux_pte_or_hugepte() running in parallel to
__split_huge_zero_page_pmd() or do_huge_pmd_wp_page_fallback() or
zap_huge_pmd() can run into the above issue. With
__split_huge_zero_page_pmd() and do_huge_pmd_wp_page_fallback() we clear
the hugepage pte before inserting the pmd entry with a regular pgtable
address. Such a clear need to wait for the parallel
find_linux_pte_or_hugepte() to finish.
With zap_huge_pmd(), we can run into issues, with a hugepage pte getting
zapped due to a MADV_DONTNEED while other cpu fault it in as small
pages.
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This fix the below build error
arch/powerpc/mm/hash_utils_64.c: In function ‘flush_hash_hugepage’:
arch/powerpc/mm/hash_utils_64.c:1381:1: error: label at end of compound statement
tm_abort:
^
make[1]: *** [arch/powerpc/mm/hash_utils_64.o] Error 1
Reported-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
For THP that is marked trans splitting, we return the pte.
This require the callers to handle the pmd_trans_splitting scenario,
if they care. All the current callers are either looking at pfn or
write_ok, hence we don't need to update them.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We can disable a THP split or a hugepage collapse by disabling irq.
We do send IPI to all the cpus in the early part of split/collapse,
and disabling local irq ensure we don't make progress with
split/collapse. If the THP is getting split we return NULL from
find_linux_pte_or_hugepte(). For all the current callers it should be ok.
We need to be careful if we want to use returned pte_t pointer outside
the irq disabled region. W.r.t to THP split, the pfn remains the same,
but then a hugepage collapse will result in a pfn change. There are
few steps we can take to avoid a hugepage collapse.One way is to take page
reference inside the irq disable region. Other option is to take
mmap_sem so that a parallel collapse will not happen. We can also
disable collapse by taking pmd_lock. Another method used by kvm
subsystem is to check whether we had a mmu_notifer update in between
using mmu_notifier_retry().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/scottwood/linux into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
|
|
Commit dc6c9a35b66b5 ("mm: account pmd page tables to the process")
added a counter that is incremented whenever a PMD is allocated and
decremented whenever a PMD is freed. For hugepages on PPC, common code
is used to allocated PMDs, but arch-specific code is used to free PMDs.
This results in kernel output such as "BUG: non-zero nr_pmds on freeing
mm: 1" when using hugepages.
Update the PPC hugepage PMD freeing code to decrement the count, just
as the above commit did for free_pmd_range().
Fixes: dc6c9a35b66b5 ("mm: account pmd page tables to the process")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.0.x
|
|
When an architecture fully supports randomizing the ELF load location,
a per-arch mmap_rnd() function is used to find a randomized mmap base.
In preparation for randomizing the location of ET_DYN binaries
separately from mmap, this renames and exports these functions as
arch_mmap_rnd(). Additionally introduces CONFIG_ARCH_HAS_ELF_RANDOMIZE
for describing this feature on architectures that support it
(which is a superset of ARCH_BINFMT_ELF_RANDOMIZE_PIE, since s390
already supports a separated ET_DYN ASLR from mmap ASLR without the
ARCH_BINFMT_ELF_RANDOMIZE_PIE logic).
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In preparation for splitting out ET_DYN ASLR, this refactors the use of
mmap_rnd() to be used similarly to arm and x86.
(Can mmap ASLR be safely enabled in the legacy mmap case here? Other
archs use "mm->mmap_base = TASK_UNMAPPED_BASE + random_factor".)
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have a powerpc specific global called mem_init_done which is "set on
boot once kmalloc can be called".
But that's not *quite* true. We set it at the bottom of mem_init(), and
rely on the fact that mm_init() calls kmem_cache_init() immediately
after that, and nothing is running in parallel.
So replace it with the generic and 100% correct slab_is_available().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
Cyril Bur
Linus Torvalds
Aneesh Kumar K.V
Dan Williams
Michael Ellerman
Nikunj A Dadhania
Kevin Hao
Anshuman Khandual
Scott Wood
Anton Blanchard
Zhang Zhen
Paul Gortmaker
Alexey Kardashevskiy
Greg Kroah-Hartman
Michael Neuling
Ingo Molnar
Bartosz Golaszewski
Luis R. Rodriguez
David Hildenbrand
Kees Cook