| Age | Commit message (Collapse) | Author |
|---|
|
This is the 4.19.87 stable release
Signed-off-by: Bruce Ashfield <bruce.ashfield@gmail.com>
|
|
This is the 4.19.86 stable release
# gpg: Signature made Sun 24 Nov 2019 02:21:09 AM EST
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
This is the 4.19.85 stable release
# gpg: Signature made Wed 20 Nov 2019 12:47:54 PM EST
# gpg: using RSA key 647F28654894E3BD457199BE38DBBDC86092693E
# gpg: Can't check signature: No public key
|
|
commit 1d31999cf04c21709f72ceb17e65b54a401330da upstream.
adjust_lowmem_bounds() checks every memblocks in order to find the boundary
between lowmem and highmem. However some memblocks could be marked as NOMAP
so they are not used by kernel, which should be skipped while calculating
the boundary.
Signed-off-by: Chester Lin <clin@suse.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1ad9fb750a104f51851c092edd7b3553f0218428 ]
Bindings for "fixed-regulator" only explicitly support "gpio" property,
not "gpios". Fix by correcting the property name.
The enet PHYs on imx6sx-sdb needs to be explicitly reset after a power
cycle, this can be handled by the phy-reset-gpios property. Sadly this
is not handled on suspend: the fec driver turns phy-supply off but
doesn't assert phy-reset-gpios again on resume.
Since additional phy-level work is required to support powering off the
phy in suspend fix the problem by just marking the regulator as
"boot-on" "always-on" so that it's never turned off. This behavior is
equivalent to older releases.
Keep the phy-reset-gpios property on fec anyway because it is a correct
description of board design.
This issue was exposed by commit efdfeb079cc3 ("regulator: fixed:
Convert to use GPIO descriptor only") which causes the "gpios" property
to also be parsed. Before that commit the "gpios" property had no
effect, PHY reset was only handled in the the bootloader.
This fixes linux-next boot failures previously reported here:
https://lore.kernel.org/patchwork/patch/982437/#1177900
https://lore.kernel.org/patchwork/patch/994091/#1178304
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a763ecc15d0e37c3a15ff6825183061209832685 ]
OMAP5's Super-Speed USB port has a software mailbox register
that needs to be fed with VBUS and ID events from an external
VBUS/ID comparator.
Without this, Host role will not work correctly.
Fixes: 656c1a65ab55 ("ARM: dts: omap5: enable OTG role for DWC3 controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f18aef742c8fbd68e280dff0a63ba0ca6ee8ad85 ]
On at least x86 and ARM64, and as documented in the ptrace man page
a skipped system call will still cause a syscall exit ptrace stop.
Previous to this commit 32-bit ARM did not, resulting in strace
being confused when seccomp skips system calls.
This change also impacts programs that use ptrace to skip system calls.
Fixes: ad75b51459ae ("ARM: 7579/1: arch/allow a scno of -1 to not cause a SIGILL")
Signed-off-by: Timothy E Baldwin <T.E.Baldwin99@members.leeds.ac.uk>
Signed-off-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f602b4871c5f7ac01d37d8b285ca947ba7613065 ]
The offsets for the bootloader environment and its redundant partition
were inverted. Fix the addresses to match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6f270d88a0c4a11725afd8fd2001ae408733afbf ]
at91sam9x5cm comes with a 2Gb NAND flash. Fix the rootfs size to
match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit df90fc64367ffdb6f1b5c0f0c4940d44832b0174 ]
sama5d4_xplained comes with a 4Gb NAND flash. Increase the rootfs
size to match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db9fd9d13e30fc67737ac9893a82e6b095e85a64 ]
The external RTL8211E RGMII Ethernet PHY is configured via external
resistors to use the address 0x1. The 0x0 address is a broadcast address
for this family of PHYs, and should not be used explicitly.
Fixes: 8c7ba536e709 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c700289a3e84d5d3f2a95cf27732a7f7fce105b ]
The size of the register should be the size of the whole memory block,
not just the registers, that are needed.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 656c1a65ab555ee5c7cd0d6aee8ab82ca3c1795f ]
Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).
Tested on OMAP5EVM and Pyra.
Suggested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b830526f304764753fcb8b4a563a94080e982a6c ]
Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11236ef582b8d66290bb3b3710e03ca1d85d8ad8 ]
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 016add12977bcc30f77d7e48fc9a3a024cb46645 ]
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ebea2a43fdafdbce918bd7e200b709d6c33b9f3b ]
The power key is controlled solely by the EC, which only tiggeres this
gpio after wakeup.
Fixes immediately return to suspend after wake from LP1.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 503fcd8464fb6cd18073e97dec59b933930655d6 ]
Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b38f6aa4b60a1fcc41f5c469981f8f62d6070ee3 ]
Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c997fe4becdc6fcbc06e23982ceb65621e6572a ]
Fix MMC1 cmd pin pull-up causing issues on carrier boards without
external pull-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8188391c127ea34d66f37eda6755d0acb51dc600 ]
Commit 6c468f109884 ("ARM: dts: tegra: add Tegra20 NAND flash
controller node") introduced the nand-controller node. However, it got
added at the wrong spot not honoring the address order. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 564706f65cda3de52b09e51feb423a43940fe661 ]
There was a dot instead of a comma. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c5f335f61ffb838fc3cc1cec9464067663eb8c8 ]
According to Documentation/devicetree/bindings/rtc/rtc-ds1307.txt the
original compatible "maxim,ds1341" is not a valid entry.
Switch to the documented "dallas,ds1341" compatible.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 245f880c25dbd8927af0f33aa5d1404370013957 ]
Update VDD_SOC voltage to 1.25V for 900MHz operating point
according to datasheet Rev. 1.3, 08/2018, 25mV is added to
the minimum allowed values to cover power supply ripple.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 95590a6286c547b7287d01c55515fb96b904aa03 ]
of_find_device_by_node takes a reference to the struct device when it
finds a match via get_device. but it fails to put_device in
at91_pm_config_ws, for_each_matching_node_and_match will get and put
the node properly, there is no need to call the of_put_node. Therefore,
just call put_device instead of of_node_put in at91_pm_config_ws.
Fixes: d7484f5c6b3b ("ARM: at91: pm: configure wakeup sources for ULP1 mode")
Suggested-by: Claudiu Beznea <Claudiu.Beznea@microchip.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff1e37c6809daab75f7b2dea1efe69330e8eb65b ]
The proper parent clock for audio subsystem for Exynos5420 and Exynos5800
SoCs is CLK_MAU_EPLL. This fixes following warning:
clk: failed to reparent mout_audss to fout_epll: -22
Fixes: ed7d1307077e: ARM: dts: exynos: Enable HDMI audio support on Peach Pit
Fixes: bae0f445c1e7: ARM: dts: exynos: Enable HDMI audio support on Peach Pi
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a2df0984e73fd9e1dad5fc3f1c307ec3de395e30 ]
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1ba23b1df0bb6eec430408614c3a11280941e112 ]
SPI controller nodes should be named 'spi' rather than 'qspi'. Fixing the
name enables dtc SPI bus checks.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e807f0298144c06740022a2f900d86b7f115595e ]
The vmmc phandle, like all power supply property names, must have the
'-supply' suffix.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 67330599f93672bd351123c729e2591a460fd24c ]
Enable panel raydium RM68200, DSI bridge & display controller.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf680cc5251487b9a39919c3cda31a108af19cf8 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/dove-cubox.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-dove-db.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@14600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/orion5x-kuroboxpro.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lschl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lsgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lswtgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd560235d8f9ddd94aa51e1c4dabdf3212b9b241 ]
The table id (second) argument to MODULE_DEVICE_TABLE is often
referenced otherwise. This is not the case for CPU features. This
leads to a warning when building the kernel with Clang:
arch/arm/crypto/crc32-ce-glue.c:239:33: warning: variable
'crc32_cpu_feature' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
static const struct cpu_feature crc32_cpu_feature[] = {
^
Avoid warnings by using __maybe_unused, similar to commit 1f318a8bafcf
("modules: mark __inittest/__exittest as __maybe_unused").
Fixes: 2a9faf8b7e43 ("crypto: arm/crc32 - enable module autoloading based on CPU feature bits")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f967f9e9fa076affb711da1a8389b5d33814fc6 ]
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ecde29569e3484e1d0a032bf4074449bce4d4a03 ]
The "lcdaclk_b_1" group is muxed with the function "lcd"
but needs a separate entry to be muxed in with "lcda"
rather than "lcd".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f217d24ecaec2012e628d21e244eef0608656a4 ]
The unit address of the Cortex-A9 SCU device node contains one zero too
many. Remove it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc893871f092be9ac1184a78f9ae1e76b85d5317 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/am437x-idk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am437x-sk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am43x-epos-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/omap3-n9.dtb: Warning (i2c_bus_reg): /ocp@68000000/i2c@48060000/ak8975@0f: I2C bus unit address format error, expected "f"
arch/arm/boot/dts/am335x-osd3358-sm-red.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/pressure@78: I2C bus unit address format error, expected "76"
arch/arm/boot/dts/am335x-boneblack.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-boneblack-wireless.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-sancloud-bbe.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am571x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am572x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am574x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-cl-som-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-sbc-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm-revc.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra76-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra7-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am335x-pdu001.dtb: Warning (spi_bus_reg): /ocp/spi@481a0000/cfaf240320a032t: SPI bus unit address format error, expected "0"
arch/arm/boot/dts/keystone-k2g-evm.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/keystone-k2g-ice.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
[tony@atomide.com: fixed mode to 644 for am335x-osd3358-sm-red.dts while at it]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dcbf6b18d81bcdc51390ca1b258c17e2e13b7d0c ]
am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.
Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 53dd9dce6979bc54d64a3a09a2fb20187a025be7 ]
The next update of libfdt has a new dependency on INT_MAX. Update the
instances of libfdt_env.h in the kernel to either include the necessary
header with the definition or define it locally.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c890ecdbe93d482512a911b299bfb009780a29c2 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/eeprom@87: I2C bus unit address format error, expected "57"
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/ft5426@56: I2C bus unit address format error, expected "38"
arch/arm/boot/dts/at91-vinco.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f8024000/rtc@64: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/at91sam9260ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek_2mmc.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9261ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/tsc2046@0: SPI bus unit address format error, expected "2"
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f5054ceed420b1f38d37920a4c65446fcc5d6b90 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dtb: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
arch/arm/boot/dts/zynq-zc770-xm013.dtb: Warning (spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format error, expected "2"
arch/arm/boot/dts/zynq-zc770-xm010.dtb: Warning (spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format error, expected "1"
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 131c3eb428ccd5f0c784b9edb4f72ec296a045d2 ]
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 57a83c5222c1b5e7b3acc72c6e60fce00a38991a ]
dtc has new checks for I2C buses. The sun9i-a80 dts file has a node named
'i2c' which causes a false positive warning. As the node is a RSB bus,
correct the node name to be 'rsb' to fix the warnings.
arch/arm/boot/dts/sun9i-a80-cubieboard4.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/codec@e89:reg: I2C address must be less than 10-bits, got "0xe89"
arch/arm/boot/dts/sun9i-a80-cubieboard4.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/pmic@745:reg: I2C address must be less than 10-bits, got "0x745"
arch/arm/boot/dts/sun9i-a80-optimus.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/codec@e89:reg: I2C address must be less than 10-bits, got "0xe89"
arch/arm/boot/dts/sun9i-a80-optimus.dtb: Warning (i2c_bus_reg): /soc/i2c@8003400/pmic@745:reg: I2C address must be less than 10-bits, got "0x745"
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0729b4af5753b65aa031f58c435da53dbbf56d19 ]
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/sun8i-a23-gt90h-v4.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a23-inet86dz.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property
arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property
arch/arm/boot/dts/sun8i-a33-q8-tablet.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-utoo-p66.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-q8-tablet.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbbc488ed85061a765cf370c3e41f383c1e0add6 ]
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dtb: Warning (i2c_bus_reg): /soc/i2c@ffc04000/adxl345@0: I2C bus unit address format error, expected "53"
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1426d40e11f730e0c0fd3700a7048082f87b0e6e ]
dtc has new checks for I2C buses. The ASpeed dts files have a node named
'i2c' which causes a false positive warning. As the node is a 'simple-bus',
correct the node name to be 'bus' to fix the warnings.
arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-romulus.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-ast2500-evb.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-opp-zaius.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dtb: Warning (i2c_bus_bridge): /ahb/apb/i2c@1e78a000: incorrect #size-cells for I2C bus
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab0b47d2eff413d60b0a1fc0c1f87f87f0d7f375 ]
dtc has new checks for SPI buses. Fix the warnings in node names.
arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dtb: Warning (spi_bus_bridge): /axi@18000000/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958525er.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958525xmc.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958622hr.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm958625hr.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
arch/arm/boot/dts/bcm988312hr.dtb: Warning (spi_bus_bridge): /axi/qspi@27200: node name for SPI buses should be 'spi'
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd73a3dd257fb838bd456a18eeee0ef0224b7a40 ]
while compiling an ipq4019 target, dtc will complain:
regulator@b089000 unit address format error, expected "2089000"
The saw0 regulator reg value seems to be
copied and pasted from qcom-ipq8064.dtsi.
This patch fixes the reg value to match that of the
unit address which in turn silences the warning.
(There is no driver for qcom,saw2 right now.
So this went unnoticed)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8148d2136002da2e2887caf6a07bbd9c033f14f3 ]
One of the Freescale recommended sequences for power off with external
PMIC is the following:
...
3. SoC is programming PMIC for power off when standby is asserted.
4. In CCM STOP mode, Standby is asserted, PMIC gates SoC supplies.
See:
http://www.nxp.com/assets/documents/data/en/reference-manuals/IMX6DQRM.pdf
page 5083
This patch implements step 4. of this sequence.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62623718fd31d08b26ebea6c8b40f24924153ab7 ]
S2MPS14 PMIC interrupt line on Exynos3250-based Artik5 evaluation board
has external pull-up resistors, so disable any pull control for it in
controller node. This fixes support for S2MPS14 PMIC interrupts and
enables operation of wakeup from S2MPS14 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1ae00833e30c9b4af5cbfda65d75b1de12f74013 ]
This is needed to make the display and venc work properly.
Compare to omap3-beagle.dts.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
Bruce Ashfield
Chester Lin
Leonard Crestez
Roger Quadros
Timothy E Baldwin
Tudor Ambarus
Chen-Yu Tsai
Philipp Rossak
H. Nikolaus Schaller
Vignesh R
Rob Herring
Marc Dietrich
Marcel Ziswiler
Fabio Estevam
Anson Huang
zhong jiang
Marek Szyprowski
Heiko Stuebner
Baruch Siach
Yannick Fertré
Stefan Agner
Linus Walleij
Geert Uytterhoeven
Grygorii Strashko
Dinh Nguyen
Christian Lamparter
Oleksij Rempel