| Age | Commit message (Collapse) | Author |
|---|
|
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen2 SoCs. Note that on these SoCs, there is
only a single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-2-geert+renesas@glider.be
|
|
"#address-cells", "#size-cells", and "ranges" are required properties
for devices nodes compatible with "mmio-sram", leading to warnings when
running "make dtbs_check":
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: '#address-cells' is a required property
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: '#size-cells' is a required property
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: 'ranges' is a required property
...
Fix this by adding the missing properties to the mmio-sram device nodes
in the DTS files for all affected R-Car Gen2 and RZ/G1 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213162604.1890-1-geert+renesas@glider.be
|
|
"make dtbs_check" emits warnings like:
pci@ee090000: interrupt-map-mask:0:0: 65280 is greater than the maximum of 63488
pci@ee0b0000: interrupt-map-mask:0:0: 65280 is greater than the maximum of 63488
pci@ee0d0000: interrupt-map-mask:0:0: 65280 is greater than the maximum of 63488
According to dt-schemas/schemas/pci/pci-bus.yaml, the PCI high address
cell value in the "interrupt-map-mask" property must lie in the range
0..0xf800.
Fix this by correcting the values from 0xff00 to 0xf800 in all affected
R-Car Gen2 and RZ/G1 DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213162459.1731-1-geert+renesas@glider.be
|
|
To improve human readability and enable automatic validation, the tuples
in the "ranges" and "dma-ranges" properties of PCI devices nodes should
be grouped. Not doing so causes "make dtbs_check" to emit warnings
like:
pcie@fe000000: dma-ranges: [[1107296256, 0, 1073741824, 0, 1073741824, 0, 2147483648, 1124073472, 2, 0, 2, 0, 1, 0]] is not valid under any of the given schemas (Possible causes of the failure):
pcie@fe000000: dma-ranges: [[1107296256, 0, 1073741824, 0, 1073741824, 0, 2147483648, 1124073472, 2, 0, 2, 0, 1, 0]] is not of type 'boolean'
pcie@fe000000: dma-ranges:0: [1107296256, 0, 1073741824, 0, 1073741824, 0, 2147483648, 1124073472, 2, 0, 2, 0, 1, 0] is too long
Fix this by grouping the tuples of the "ranges" and "dma-ranges"
properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-5-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped. While "make dtbs_check" does not impose this yet for the
"interrupts" property, it does for the "interrupt-map" property, leading
to warnings like:
pci@ee090000: interrupt-map:0: [0, 0, 0, 1, 5, 0, 108, 4, 2048, 0, 0, 1, 5, 0, 108, 4, 4096, 0, 0, 2, 5, 0, 108, 4] is too long
pci@ee0d0000: interrupt-map:0: [0, 0, 0, 1, 5, 0, 113, 4, 2048, 0, 0, 1, 5, 0, 113, 4, 4096, 0, 0, 2, 5, 0, 113, 4] is too long
Fix this by grouping the tuples of the "interrupts" and "interrupt-map"
properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-4-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
Improve the user friendliness of the DTS code base by including the
R-Car product name in each R-Car Gen2 DTSI file.
The product names are taken from:
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the SATA device nodes on R-Car H1, H2, and M2-W to use a 2 MiB
I/O space, as specified in Rev.1.0 of the R-Car H1 and R-Car Gen2
hardware user manuals.
See also commit e9f0089b2d8a3d45 ("arm64: dts: r8a7795: Correct SATA
device size to 2MiB").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like, clock latency, voltage tolerance,
etc) as well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"This is a branch with a few merge requests that either came in late,
or took a while longer for us to review and merge than usual and thus
cut it a bit close to the merge window. We stage them in a separate
branch and if things look good, we still send them up -- and that's
the case here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
soc: qcom: smem: introduce qcom_smem_virt_to_phys()
soc: qcom: qmi: fix a buffer sizing bug
MAINTAINERS: Update pattern for qcom_scm
soc: Unconditionally include qcom Makefile
soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
soc: qcom: smem: fix qcom_smem_set_global_partition()
soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
soc: qcom: smem: byte swap values properly
soc: qcom: smem: return proper type for cached entry functions
soc: qcom: smem: fix first cache entry calculation
soc: qcom: cmd-db: Make endian-agnostic
drivers: qcom: add command DB driver
arm64: dts: renesas: salvator-common: Add ADV7482 support
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
...
|
|
Enable support for the ARM Performance Monitor Units in the Cortex-A15
CPU cores on R-Car M2-W by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This commit adds watchdog support to the r8a7791 dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The r8a7791 has two FDP1 instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41fab ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Fixes: bb21803ea440 ("ARM: dts: r8a7791: add soc node")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Consistently use a single space before a =.
This patch fixes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort subnodes of root node to aid maintenance.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Consistently use a single space after a =.
This patch removes instances where a tab or multiple spaces are used
instead. It also avoids running over 80 columns in width in one of the
lines where whitespace is updated.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Reduce size of thermal registers in DT for r8a7791 (R-Car M3-W) SoC.
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the case
on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is PAGE_SIZE.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The R-Car M2W hardware manual states that Tc = –40°C to +105°C. The
thermal sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
Fixes: cac68a56e34b9810 ("ARM: dts: r8a7791: enable to use thermal-zone")
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7791 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use newly added R-Car Gen2 Ether fallback compat string
in the DT of the r8a7791 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Currently only the primary CPU in the CA15 cluster has a clocks
property, while the secondary CPU core is driven by the same clock.
Add the missing clocks property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use newly added R-Car GPIO Gen2 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7791 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use the preferred generic node name instead of the specific name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that resets usually match the corresponding module clocks.
Exceptions are:
- The audio module has resets for the Serial Sound Interfaces only,
- The display module has only a single reset for all DU channels, but
adding reset properties for the display is postponed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The current practice is to not group clocks under a "clocks" subnode,
but just put them together with the other on-SoC devices.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Convert the R-Car M2-W SoC from the old "Renesas R-Car Gen2 Clock Pulse
Generator (CPG)", "Renesas CPG DIV6 Clock", and "Renesas CPG Module Stop
(MSTP) Clocks" DT bindings to the new unified "Renesas Clock Pulse
Generator / Module Standby and Software Reset" DT bindings.
This simplifies the DTS files, and allows to add support for reset
control later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use newly added R-Car SATA Gen2 fallback compat string
in the DT of the r8a7791 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use R-Car Gen 2 fallback binding for vind nodes in DT for r8a7791 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car M2-W has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The bogus 'device_type = "pci"' confuses dtc, causing lots of totally
unrelated warnings. After fixing that, real warnings like
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (pci_device_reg): Node /pci@ee090000/usb@0,1 PCI unit address format error, expected "1,0"
are left. Correct the unit-addresses and reg properties of the subnodes
to fix these.
Signed-off-by: Rob Herring <robh@kernel.org>
[geert: Improve description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add node for the GyroADC block and it's associated clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The device trees for Renesas SoCs use either pfc or pin-controller as the
node name for the PFC device. This patch is intended to take a step towards
unifying the node name used as pin-controller which appears to be the more
generic of the two and thus more in keeping with the DT specs.
My analysis is that this is a user-visible change to the extent that kernel
logs, and sysfs entries change from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The current practice is to not add _clk suffixes to clock node names in
DT, as these names are used as the actual clock names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: ee9141522dcf13f8 ("ARM: shmobile: r8a7791: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 6f9314ce258c8504 ("ARM: dts: r8a7791: Fix W=1 dtc warnings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use recently added R-Car Gen 2 fallback binding for msiof nodes in
DT for r8a7791 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Use recently added R-Car Gen 2 fallback binding for iic nodes in
DT for r8a7791 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use recently added R-Car Gen 2 fallback binding for i2c nodes in
DT for r8a7791 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
A fallback binding for the Renesas R-Car Gen2 PHY driver was
added by commit 7777cb8ba08d ("phy: rcar-gen2: add fallback binding").
This patch makes use of this binding in the DT for the r8a7791 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
|
|
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
Geert Uytterhoeven
Magnus Damm
Wolfram Sang
Viresh Kumar
Linus Torvalds
Fabrizio Castro
Laurent Pinchart
Simon Horman
Chris Paterson
Magnus Damm
Rob Herring
Marek Vasut
Kuninori Morimoto
Marc Zyngier