| Age | Commit message (Collapse) | Author |
|---|
|
This adds a "HPA1" prefix to the amplifiers on both audio cards, this is
done in order to get more consistency for userspace running on RDU2 and
RDU3, where we have two amplifiers on a single card device in the "Zest"
configuration.
Also adjust the card names to the new standard expected by userspace.
Signed-off-by: Cory Tusar <cory.tusar@zii.aero>
[adjusted commit message]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ALERT signaling happens on the falling edge of the signal, as rising
edge doesn't really have any notion, as it may happen much later (due to
shared IRQ line) or too early if the chip resolves the fault itself. So
only trigger the IRQ on the edge we are actually interested in.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To use the reduced reporting mode the threshold values need to be set
explicitly. Configure the threshold to be less than 0.5% of the full
touchscreen range. This seems to be a good compromise between system
load and input accurancy.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The current 25 Ohm drive-strength is much too strong, resulting in
significant overshoot of the signal. Reduce the drive-strength to
75 Ohm to get rid of those issues.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the i.MX6 WDOG1 internal watchdog for warm reboots. This allows
to issue emergency restarts without clearing the RAM, so collecting oops
logs from ramoops pstore in barebox becomes feasible.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dtschema for GPIO controllers expects GPIO hogs to end with 'hog'
suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update MDIO configuration with ZII devices to fully utilize
MDIO endpoint capabilities. All devices support 12.5MHz clock and
don't require MDIO preable.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently we don't ensure that the LDB is clocked from the video PLL
and relied on the bootloader to do the correct setup. This isn't always
true, in which case we would run with a vastly different video clock
than the desired one. Fix this by assigning the proper parent to the
LDB.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add node for UCS1002 USB charger chip connected to front panel USB and
replace "regulator-fixed" previously used to control VBUS.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Specify 'vdd' and 'vddio' supplies for accelerometer to avoid warnings
during boot.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/iio/accel/mma8452.txt,
the correct interrupt-names are "INT1" and "INT2", so fix them
accordingly.
While at it, modify the node to only specify "INT2" since providing
two interrupts is not necessary or useful (the driver will only use
one).
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[andrew.smirnov@gmail.com modified the patch to drop INT1]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.
Note the GPIO polarity in the driver was ignored before and always
assumed to be active low, when all the DTs are fixed we will start
respecting the specified polarity. Switch polarity in DT to the
currently assumed one, this way when the driver changes the
behavior will not change.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that the backlight driver is upstream, we can properly manage the
backlight from the panel.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds the i2c device node for the ethernet switch watchdog.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use the correct compatible for the new protocol used by the firmware
on the touch controller, the GPIO wakeup isn't used in that case.
Also eGalax touch needs axis swapping, just as with the RMI4 touch.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On the imx6qdl-zii-rdu2 board the RTC functionality is provided via
a DS1341 RTC connected via I2C bus, so we can safely disable the internal
one.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
|
|
The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.
The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.
All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f64992d1a916 ("ARM: dts: imx6: RDU2: Add Switch interrupts")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RAVE SP found on RDU2 implements power button control compatible with
the rave-sp-pwrbutton driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RAVE SP found on RDU2 implements backlight control compatible with the
rave-sp-backlight driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ZII's RDU2s come with two EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove unnecessary #address-cells/#size-cells from the switch nodes
to fix the following DTC warnings:
arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This touchscreen is present instead of the RMI4 touch on some SKUs of
the RDU2. Keep it disabled by default, the bootloader will enable it
instead of the RMI4 touch when running on one of those units.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This bumps the SoC/PU domain operating points by 25mV, giving a total
of 75mV margin to the minimum required voltages. This gets rid of
brown-outs seen due to voltage drop-out on the board.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
With MFD and watchdog drivers for RAVE SP device support added by
538ee27290fa ("mfd: Add driver for RAVE Supervisory Processor") and
c3bb33345721 ("watchdog: Add RAVE SP watchdog driver") add
corresponding DT node for RDU2.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The system has an external watchdog in the environment processor
so the internal watchdog is of no use.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: cphealy@gmail.com
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
device_type = "pci" should be used for the SoC level PCI controller and
it is already present at imx6qdl.dtsi.
Remove it from the subnode in order to fix the following build
warnings with W=1:
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing bus-range for PCI bridge
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (unit_address_format): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is needed for the bootloader to patch in the correct MAC address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.15" from Shawn Guo:
- New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
TX modules for MB7 from Ka-Ro Electronics, i.MX6 Wandboard revd1
variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
Vining-2000 board.
- Use the 'vpcie-supply' property for PCIe device for boards
imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
- A series from Jagan Teki to update imx6qdl-icore board with audio,
touch and CAN support.
- Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
tempmon support for i.MX6UL.
- A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
and i.MX6 TX modules.
- Fix DTC warnings in i.MX device trees, dropping leading zeros from
unit address, correcting display nodes notation and display port
names, fixing nodes with unit name and no reg property.
- Other random device updates for various board support.
* tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
ARM: dts: imx53-tx53: fix interrupt flags
ARM: dts: imx28-tx28: fix interrupt flags
ARM: dts: display5: Device tree description of LWN's DISPLAY5 board
ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg property
ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg property
ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg property
ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg property
ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg property
ARM: dts: imx: add ZII RDU1 board
ARM: dts: imx: add support for TX6 modules on MB7 baseboard
ARM: dts: imx: add support for TX6QP
ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboard
ARM: dts: imx6-tx6: move display configuration to .dtsi file
ARM: dts: imx6-tx6: add support for I2C bus recovery
ARM: dts: imx6-tx6: convert to using simple-audio-card
ARM: dts: imx6-tx6: specify ethernet phy reset post-delay
ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
ARM: dts: imx6-tx6: add trickle-charge config for DS1339
ARM: dts: imx6-tx6: remove obsolete ipu1 alias
ARM: dts: imx6-tx6: remove obsolete eeti,egalax_ts
...
[arnd: made sure we have no new leading zeroes in unit address during merge]
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This is causing issues with some specific controller configurations, as
the platform isn't power limited it's better to keep it disabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Just like the OTG port, USB H1 has no over-current detection wired up.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Micrel PHY has its interrupt pin connected to a GPIO line. Wire
this up in the device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Marvell switch has its interrupt pin connected to a GPIO
line. Wire this up in the device tree. This then allows us to use
interrupts from the embedded Ethernet PHYs in the switch. Also wire
them up in device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Marvell switch has an EEPROM connected to it. List the size in DT,
in order to enable access to it via ethtool.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The RDU2 has a Marvell 88E6352 switch. Both the FEC and the i210
Ethernet interfaces are connected to the switch. Make the FEC the DSA
"CPU" port, and the i210 as a regular port on the switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The FEC has a Micrel PHY connected to it. This PHY is managed using
the bit-banging MDIO bus. Add this to the device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the Zodiac Inflight Innovations RDU2 board,
which has both a Quad and a QuadPlus variant.
The board supports different panels, with the bootloader patching
in the correct compatible, depending on the hardware configuration.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
Cory Tusar
Lucas Stach
Philipp Zabel
Krzysztof Kozlowski
Fabio Estevam
Chris Healy
Andrey Smirnov
Andrew F. Davis
Linus Torvalds
Uwe Kleine-König
Fabio Estevam
Bartosz Golaszewski
Arnd Bergmann
Rob Herring
Andrew Lunn