| Age | Commit message (Collapse) | Author |
|---|
|
There are some differences between the schematics and the official firmware
DTS [1]. So based on these additional information the following has been
changed:
* use consistent "CAM_GPIO1" for camera LED
* use consistent "CAM_GPIO0" for camera shutdown
* add "USB_LIMIT" for USB current limit (0=600mA, 1=1200mA)
[1] - https://github.com/raspberrypi/firmware/blob/master/extra/dt-blob.dts
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The idea is to give useful names to GPIO lines that an implementer
will be using from userspace, e.g. for maker type projects. These are
user-visible using tools/gpio/lsgpio.c
v2: Major rewrite by anholt: Flatten each GPIO line to a line in the
file for better diffing, prefix all expansion header pins with
"P<number>" or "P5HEADER_P<number>" and drop the mostly-unused
GPIO_GEN<smallnumber> names in favor of GPIO<socgpionumber>, fix
extra '[]' on a couple of lines, fix locations of SD_CARD_DETECT,
CAM_GPIO and STATUS_LED, fix HDMI_HPD polarities, rewrite A+ using
unreleased schematics.
v3: More changes by anholt: Drop P<number> / P5HEADER<number>
prefixes. I had been skeptical about adding them, and was
convinced to drop them by Gottfried (who probably has more
experience with GPIOs in educational contexts than the rest of
us). Also drop [] brackets for "is pinmuxed", which didn't seem
to clarify, and were ambiguous for things like the SPI_*-labeled
pins which may or may not actually be pinmuxed to SPI.
v4: Rename B+'s SDA0/SCL0 to match the other boards, despite the
naming on its schematic.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
As the alt3 group has no pins left drop it from &gpio.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
|
|
In case dr_mode isn't passed via DT, the dwc2 defaults to OTG mode.
But all Raspberry Pi boards here are designed only for host mode.
So fix this issue by providing a dtsi file which set the dr_mode
to host.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
VC4 is the GPU (display and 3D) present on the 283x.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
This one is essentially the same as revision 2 B board (with the I2S on
P5 header).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on bcm2835.dtsi -> bcm283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
|
Stefan Wahren
Linus Walleij
Gerd Hoffmann
Eric Anholt
Lubomir Rintel