| Age | Commit message (Collapse) | Author |
|---|
|
This property applies to consumers of io-channels. In this case we
have a provider so the property is not used.
Recent changes to dt-schema result int his being reported as an error
as a dependency is enforced between this property and io-channels.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The SP805 DT binding requires two clocks to be specified, but the
Broadcom Cygnus DT currently only specifies one clock.
In practice, Linux would pick a clock named "apb_pclk" for the bus
clock, and the Linux and U-Boot SP805 driver would use the first clock
to derive the actual watchdog counter frequency.
Since currently both are the very same clock, we can just double the
clock reference, and add the correct clock-names, to match the binding.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix dtschema validator warnings like:
l2-cache@22000: $nodename:0:
'l2-cache@22000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The MDIO node on Cygnus had an reversed #address-cells and
#size-cells properties, correct those.
Fixes: 40c26d3af60a ("ARM: dts: Cygnus: Add the ethernet switch and ethernet PHY")
Reported-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.19, please pull the following:
- Clement adds ethernet aliases to the Cygnus DTS include file such that
a DT aware bootloader such as u-boot can properly insert MAC addresses
- Mohamed adds a Device Tree node for the HWRNG found on Cygnus SoCs
- Vivek migrates all the BCM5301x (Northstar) Device Tree sources to use
the proper USB 3.0 PHY representation using its parent MDIO bus.
Vivek also completes the Linksys EA9500 Device Tree by adding support
for LEDs, internal and external switches.
- Rafal adds the ARM architected timer to the BCM53573 Device Tree
include file.
- Eric adds the Performance Monitoring Unit to the BCM2837 DTS include
file since it was absent before
- Boris adds the BCM283x transposer block to the Device Tree
- Stefan adds the Raspberry Pi Compute Module (CM1) Device Tree include
and sources.
* tag 'arm-soc/for-4.19/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Add support for Linksys EA9500
ARM: dts: BCM53573: Add architected timer
ARM: dts: BCM5301X: Make USB 3.0 PHY use MDIO PHY driver
ARM: dts: cygnus: enable iproc-hwrng
ARM: dts: cygnus: add ethernet0 alias
ARM: dts: bcm283x: Add Transposer block
ARM: dts: bcm283x: Add the PMU to the devicetree.
ARM: dts: add Raspberry Pi Compute Module and IO board
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable the HW rng driver "iproc-rng200" for all cygnus platforms.
Signed-off-by: Mohamed Ismail Abdul Packir Mohamed <mohamed-ismail.abdul@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC
Fixes: cd590b50a936 ("ARM: dts: enable PCIe support for Cygnus")
Fixes: f6b889358a82 ("ARM: dts: Enable MSI support for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix I2C controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC.
Fixes: b51c05a331ff ("ARM: dts: add I2C device nodes for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
set IRQ triggering type to IRQ_TYPE_EDGE_RISING for ARM Global timers.
Fixes: c9ad7bc5fe3 ("ARM: dts: Enable Broadcom Cygnus SoC")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.15" from Florian Fainelli:
This pull request contains Broadcom ARM-based Device Tree changes for 4.15,
please pull the following:
- Eric adds support for the CLCD and PWM controller on Cygnus chis
- Loic fixes the console path on the Raspberry Pi 3 (already submitted as
fixes) and then proceeds with enabling the BCM43438 bluetooth chip on
the Raspberry Pi 3
- Rafal specifies the USB ports on the Luxul XWR-1200
- Dan adds support for the Luxul ABR-4500 based on BCM47094, the Luxul XAP-810
and XAP-1440 both based on BCM53573
- Florian adds support for the Broadcom Hurricane 2 SoC by adding general
machine binding, clock binding, SoC DTS include file and a DTS for the
Ubiquiti Networks UniFi Switch 8
* tag 'arm-soc/for-4.15/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Hurricane 2: Add basic support for Ubiquiti UniFi Switch 8
dt-bindings: Add Ubiquiti Networks vendor prefix
ARM: dts: Add Broadcom Hurricane 2 DTS include file
dt-bindings: Document Broadcom Hurricane 2 clocks
dt-bindings: Add documentation for Broadcom Hurricane 2 SoCs
ARM: dts: BCM53573: Add DT for Luxul XAP-1440
ARM: dts: BCM53573: Add DT for Luxul XAP-810
ARM: dts: BCM5301X: Add DT for Luxul ABR-4500
ARM: dts: BCM5301X: Add DT for Luxul XBR-4500
ARM: dts: BCM5301X: Specify USB ports for USB LED of Luxul XWR-1200
ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
ARM: dts: bcm283x: Fix console path on RPi3
ARM: dts: cygnus: Add the PWM node
ARM: dts: cygnus: Add the CLCD controller
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This is connected up to the backlight on 911360_entphn, which we'll
need for a panel driver. For now, leave the node disabled in the
shared dtsi.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This doesn't yet enable it on any particular platform, as we still
need a panel driver for bcm911360_entphn.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add dt nodes for generic-ehci/ohci host controller.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add nodes for peripherals in Cygnus dtsi: sdhci, keypad, spi, dma,
pinmux configs.
Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add PMU capability to Cygnus so trace and performance profiling
can be used.
Signed-off-by: Jason Uy <jason.uy@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Move v3d devicetree node to proper address ordered location in Cygnus
dtsi.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix incorrect Cygnus UART2 register base.
Fixes: 0f0b21a83ad2 ("ARM: dts: Move all Cygnus peripherals into axi bus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Cygnus has a single amac controller connected to the B53 switch with 2
PHYs. On the BCM911360_EP platform, those two PHYs are connected to the
external ethernet jacks.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This loads the VC4 driver on the 911360_entphn platform (with the
corresponding series sent to dri-devel), which is supported by master
of the Mesa tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The unit address for the msi controller is not valid as there is no reg
property, so remove it. Also, msi-controller is the preferred node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Tested-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Oza Pawandeep <oza@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The M0 processor handles interrupts for the always-on CRMU GPIO
controller. Setting the CRMU GPIO driver with the mailbox controller as
the interrupt parent allows the mailbox controller to forward interrupts
from the M0 to the GPIO driver for processing.
Reviewed-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Tested-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com>
Reviewed-by: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Reviewed-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Reviewed-by: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Tested-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Remove 0x from pinctrl node to match device tree naming convention.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This patch adds the DT node for Broadcom's iproc-static-adc
controller driver.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
In Cygnus SOC touch screen controller registers are shared with ADC and
flex timer. Using readl/writel could lead to race condition. So touch
screen driver is enhanced to support register access using syscon framework
API's to take care of mutually exclusive access.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Enable MSI support for Broadcom Cygnus platforms
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Enable PCIe PHY for both PCIe root complexes on Cygnus
Signed-off-by: Ray Jui <rjui@broadcom.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
[florian: Fix missing #address-cells and #size-cells properties]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add ngpios property in cygnus ASIU, CCM and CRMU gpio controller's node
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
ASIU gpio controller's pins are muxed with pin-cntroller.
Add this mapping through property "gpio-ranges".
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Move aliases from bcm-cygnus.dtsi back to individual .dts files. Also
clean up the chosen node to have the stdout-path using the proper alias
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The third compatible string "brcm,brcmnand" in bcm-cygnus.dtsi nand node
is incorrect, redundant and should be removed. "brcm,brcmnand" is meant to
be used by STB based Broadcom SoCs. All iProc based SoCs should use
"brcm,nand-iproc".
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This patch enables touchscreen support on bcm958300k and bcm958305k.
Touchscreen is connected to these boards through the bcm9hmidc daughter
card, and therefore also adding bcm9hmidc.dtsi that describes the
daughter card
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Reorder all Cygnus peripherals based on base register addresses in
bcm-cygnus.dtsi
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Move all Cygnus peripherals to be under the "axi" bus node of type
"simple-bus"
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Put all Cygnus core components into "core" node of type "simple-bus" in
bcm-cygnus.dtsi
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Move aliases into bcm-cygnus.dtsi to avoid duplications in Cygnus dts
files
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Enable NAND support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This enables all 3 GPIO controllers including the ASIU GPIO, the
chipcommonG GPIO, and the ALWAYS-ON GPIO, for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This enables the IOMUX support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add I2C device nodes and its properties in bcm-cygnus.dtsi but keep
them disabled there. Individual I2C devices can be enabled in board
specific dts file when I2C slave devices are enabled in the future
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
DT files to enable cygnus consisting on reference designs
and cygnus core configuration.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <aparames@broadcom.com>
Tested-by: Jonathan Richardson <jonathar@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
Jonathan Cameron
Andre Przywara
Krzysztof Kozlowski
Florian Fainelli
Rob Herring
Olof Johansson
Mohamed Ismail Abdul Packir Mohamed
Clément Péron
Ray Jui
Arnd Bergmann
Eric Anholt
Raveendra Padasalagi
Jonathan Richardson
Jason Uy
Scott Branden
Jonathan Richardson
Ray Jui
Pramod Kumar
Scott Branden