| Age | Commit message (Collapse) | Author |
|---|
|
In order to update MAC address entries in the ethernet nodes in Device Tree
both mainline U-Boot and Barebox bootloaders accept the same format of aliases,
which is 'ethernetX', where X stands for an interface number.
Other platforms in the mainline Linux, that comprise ethernet references in
'/aliases' node (like various flavours of imx or sunXi), follow the naming
scheme described above.
This commit ajusts ethernet aliases of Marvell Armada 38x SoC to be properly
recognized by bootloaders' MAC address fixup routines.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-5-git-send-email-mw@semihalf.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Merge "ARM: mvebu: DT changes for v3.17 (round 2)" from Jason Cooper:
mvebu DT changes for v3.17 (round 2):
- kirkwood
* Add d2 Network v2 board
- mvebu
* Add Armada 375 ethernet node
* Add CA9 MPcore SoC controller node
* Add support for dynamic freq scaling on Armada XP
* tag 'mvebu-dt-3.17-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: update Armada XP DT for dynamic frequency scaling
ARM: mvebu: add CA9 MPcore SoC Controller node
ARM: mvebu: Enable the network controller in Armada 375 DB board
ARM: mvebu: Add support for the network controller in Armada 375 SoC
ARM: Kirkwood: add DT support for d2 Network v2
ARM: Kirkwood: allow to use netxbig DTSI for d2net_v2 DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The CA9 MPcore SoC Control block is a set of registers that allows to
configure certain internal aspects of the core blocks of the SoC
(Cortex-A9, L2 cache controller, etc.). In most cases, the default
values are fine so they aren't many reasons to touch those registers,
but there is one exception: to support cpuidle on Armada 38x, we need
to modify the value of the CA9 MPcore Reset Control register.
Therefore, this commit adds a new Device Tree binding for this
hardware block, and uses this new binding for the Armada 38x Device
Tree file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Link: https://lkml.kernel.org/r/1404913221-17343-11-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
wildcard
Wildcards in compatible strings should be avoid. "marvell,armada38x"
was recently introduced but was not yet used.
The armada 385 SoC is a superset of the armada 380 SoC (with more CPUs
and more PCIe slots). So this patch replaces the use of
"marvell,armada38x" by the "marvell,armada380" string.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1403533011-21339-1-git-send-email-gregory.clement@free-electrons.com
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Merge "mvebu DT changes for v3.16 (incremental #2)" from Jason Cooper:
- kirkwood
- add OpenRD boards
- make keymile boards bootable with latest kernels
- mvebu
- add ehci/xhci to Armada 375/38x boards
* tag 'mvebu-dt-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: add kirkwood-km_fixedeth DTS file
ARM: dts: kirkwood: add kirkwood-km_common DTSI files
ARM: dts: kirkwood: resynch 98dx4122 dtsi
ARM: mvebu: add Device Tree description for the EHCI controllers on Armada 375
ARM: mvebu: add Device Tree description of the xHCI controller on Armada 375
ARM: mvebu: add Device Tree description of the EHCI controller on Armada 38x
ARM: mvebu: add Device Tree description of xHCI controllers on Armada 38x
ARM: Kirkwood: DT versions of OpenRD boards
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Merge "ARM: mvebu: DT changes for v3.16" from Jason Cooper:
mvebu DT changes for v3.16
- kirkwood
- rework nsa3x0 board to add nsa320
- large cleanup to facilitate use in barebox
- guruplug phy updates
- audio updates for t5325
- mvebu
- use clocks vice clock-frequency for uart nodes
- armada 375/380/385
- add watchdog node
- add coherency fabric
- add smp support
- add sdhci
- add ahci
- add thermal sensor
- armada 370/XP
- and pmsu
* tag 'mvebu-dt-3.16' of git://git.infradead.org/linux-mvebu: (35 commits)
ARM: Kirkwood: t5325: Use simple card to instantiate audio
ARM: Kirkwood: DT: Add missing #sound-dai-cells property
ARM: Kirkwood: Add node for audio codec
ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id
ARM: dts: kirkwood: set Guruplug ethernet PHY compatible
ARM: dts: kirkwood: set default pinctrl for I2C1 on 6282
ARM: dts: kirkwood: set default pinctrl for I2C0
ARM: dts: kirkwood: set default pinctrl for NAND
ARM: dts: kirkwood: set default pinctrl for SPI0
ARM: dts: kirkwood: set default pinctrl for UART0/1
ARM: dts: kirkwood: set default pinctrl for GBE1
ARM: dts: kirkwood: consolidate common pinctrl settings
ARM: dts: kirkwood: add pinctrl node to common SoC include
ARM: dts: kirkwood: rename pin-controller nodes
ARM: dts: kirkwood: remove clock-frequency properties from UART nodes
ARM: dts: kirkwood: add stdout-path property to all boards
ARM: dts: kirkwood: add node labels
ARM: mvebu: Enable the thermal sensor in Armada 380/385 SoC
ARM: mvebu: Enable the thermal sensor in Armada 375 SoC
ARM: mvebu: don't use clocks property in UART node for Netgear RN2120
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Marvell Armada 38x SoCs contains one EHCI controller. This commit
adds the Device Tree description of this interface at the SoC level,
and also enables the USB2 port on the Armada 385 DB platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1400149062-32661-16-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Marvell Armada 38x SoCs contains two xHCI controllers. This commit
adds the Device Tree description of those interfaces at the SoC level,
and also enables the two USB3 ports on the Armada 385 DB platform and
one USB3 port on the Armada 385 RD platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1400149062-32661-15-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit enables the thermal sensor found in Armada 380/385 SoCs.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1398371004-15807-11-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Back when the Armada 370 and Armada XP initial support was introduced,
the only way to pass the clock frequency to the of_serial driver was
through a clock-frequency Device Tree property.
Thanks to 0bbeb3c3e84bc963d1c66661e082d207023b0e5c ('of serial port
driver - add clk_get_rate() support'), it is possible to use the
standard 'clocks' DT property to reference the clock used for a
particular UART controller. This clock is then used by the of_serial
driver to retrieve the clock rate.
This commit modifies the SoC-level Device Tree files of Armada 370,
Armada XP, Armada 375 and Armada 38x to use this possibility. Since
there is no gatable clock for the UART controllers, we simply
reference the TCLK, which is the main SoC clock for the peripherals.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1397806908-7550-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Marvell Armada 38x processors contain two AHCI compatible
interfaces. This commit adds the Device Tree description of those
interfaces at the SoC level, and also enables them on the Armada 385
DB platform, which allows access to both interfaces through SATA
ports.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397574006-5868-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
In commit "mmc: sdhci-pxav3: add support for the Armada 38x SDHCI
controller", the sdhci-pxav3 driver has been extended to also be
usable on Armada 38x platforms.
Therefore, this commit adds the necessary Device Tree informations to
declare this SDHCI interface in the Armada 38x SoC, and also in the
Armada 385 Development Board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1397486478-16991-2-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit improves the Armada 38x Device Tree to add the CPU reset
and PMSU Device Tree nodes as well as the declaration of the enabling
method for the CPUs. These are needed to get SMP working on Armada 38x
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483648-26611-12-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit adds the necessary Device Tree information to enable the
coherency fabric on Armada 38x.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483228-25625-11-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Add the DT nodes to enable the watchdog support available on
Armada 380/385 SoC.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1397481813-4962-9-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The mvmdio driver accesses some register of the Ethernet unit. It
therefore takes a reference and enables a clock. However, on Armada
38x, no clock specification was given in the Device Tree, which leads
the mvmdio driver to fail when being used as a module and loaded
before the mvneta driver: it tries to access a register from a
hardware unit that isn't clocked.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1395790439-21332-3-git-send-email-thomas.petazzoni@free-electrons.com
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Armada 38x SoC family has a NAND controller, compatible
with the controller in Armada 370/375/XP SoCs. Add support for
it in the devicetree file.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-5-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Armada 38x SoC family has a clock provider called "Core Divider",
derived from the fixed 2 GHz main PLL clock. This is similar to the
one on A370, A375 and AXP.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-4-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Armada 38x SoCs have a 2 GHz fixed main PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1394742273-5113-3-git-send-email-ezequiel.garcia@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 375 and Armada 38x Device Tree files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Instead of hardcoding 0 and 1 to indicate SPI and PPI GIC interrupts,
use the definitions of <dt-bindings/interrupt-controller/arm-gic.h> to
clarify the Device Tree code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Armada 380 and 385 SoCs are new SoCs from Marvell, based on a
Cortex-A9 cores (single core for 380, dual core for 385) and a number
of hardware blocks that are common with earlier SoCs from the mvebu
family.
The provided Device Tree describes the following parts of the SoC:
* CPU
* Device Bus
* Clocks
* Interrupt controllers: GIC and MPIC
* GPIO controllers
* I2C buses
* L2 cache
* MBus controller
* Pinctrl
* Serial
* SPI buses
* System controller (for reboot)
* Timer
* XOR engines
* PCIe controllers
* Network interfaces
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
Marcin Wojtas
Olof Johansson
Gregory CLEMENT
Arnd Bergmann
Ezequiel Garcia
Thomas Petazzoni