| Age | Commit message (Collapse) | Author |
|---|
|
park mode
[ Upstream commit 3d157c28d2289edf0439e8308e8de3a06acaaf0e ]
This patch updates the documentation with the information related
to the quirks that needs to be added for disabling all SuperSpeed XHCI
instances in park mode.
Cc: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0ff9b590733079f7f9453e5976a9dd2630949e3 ]
Add property "pinctrl-names" to swap pin mode between gpio and dpi mode.
Set the dpi pins to gpio mode and output-low to avoid leakage current
when dpi disabled.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 26d5bb9e4c4b541c475751e015072eb2cbf70d15 ]
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 830dbce7c76ea529decac7d23b808c1e7da3d891 upstream.
The documented compatible value for R-Car H3 is
"renesas,r8a7795-rcar-usb2-clock-sel", not
"renesas,r8a77950-rcar-usb2-clock-sel".
Fixes: 311accb64570db45 ("clk: renesas: rcar-usb2-clock-sel: Add R-Car USB 2.0 clock selector PHY")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191016145650.30003-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 73852e56827f5cb5db9d6e8dd8191fc2f2e8f424 ]
The abracon,tc-resistor property value is in kOhm.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b78ac6ecd1b6b46f8767cbafa95a7b0b51b87ad8 ]
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27582f0ea97fe3e4a38beb98ab36cce4b6f029d5 ]
With recent dtc and W=1:
Warning (graph_port): video-receiver@70/port@10: graph node unit address error, expected "a"
Warning (graph_port): video-receiver@70/port@11: graph node unit address error, expected "b"
Unit addresses are always hexadecimal (without prefix), while the bases
of reg property values depend on their prefixes.
Fixes: e69595170b1cad85 ("media: adv748x: Add adv7481, adv7482 bindings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 42bf02ec6e420e541af9a47437d0bdf961ca2972 upstream
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.
This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.
If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.
[1] Device mode enumeration trace showing PHY Erratic Error.
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c737abc193d16e62e23e2fb585b8b7398ab380d8 upstream.
Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
the UART1 registers that should not be declared in this node.
Update the example in DT bindings document accordingly.
Signed-off-by: allen yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80785f5a22e9073e2ded5958feb7f220e066d17b upstream.
Armada 8040 needs four clocks to be enabled for MDIO accesses to work.
Update the binding to allow the extra clock to be specified.
Cc: stable@vger.kernel.org
Fixes: 6d6a331f44a1 ("dt-bindings: allow up to three clocks for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0df82dcd55832a99363ab7f9fab954fcacdac3ae ]
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch add the mcp25625 to the device tree bindings documentation.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6c0c5dc33ff42af49243e94842d0ebdb153189ea upstream.
Add new compatible to the device tree bindings.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f164d0204b1156a7e0d8d1622c1a8d25752befec upstream.
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 321cc359d899a8e988f3725d87c18a628e1cc624 ]
We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 218bbea11a777c156eb7bcbdc72867b32ae10985 upstream.
Add support for the four-port variant of the Qualcomm QCA833x switch.
The CPU port default link settings can be reconfigured using
a fixed-link sub-node.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7e5d05e18ba1ed491c6f836edee7f0b90f3167bc ]
We need to introduce a new compatible name for the Meson-AXG SoC
in order to support the RMII 100M ethernet PHY, since the PRG_ETH0
register of the dwmac glue layer is changed from previous old SoC.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 03d9fbc39730b3e6b2e7047dc85f0f70de8fb97d ]
The Meson8m2 SoC is a variant of Meson8 with some updates from Meson8b
(such as the Gigabit capable DesignWare MAC).
It is mostly pin compatible with Meson8, only 10 (existing) CBUS pins
get an additional function (four of these are Ethernet RXD2, RXD3, TXD2
and TXD3 which are required when the board uses an RGMII PHY).
The AOBUS pins seem to be identical on Meson8 and Meson8m2.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a95691bc54af1ac4b12c354f91e9cabf1cb068df ]
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f130307054a59ca21d2396f386be77ebd2e8ca96 ]
Fixes: 14da3ed8dd08c581 ("devicetree/bindings: display: Document common
panel properties")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 34df2466b48dfe258e14fe2a7bc4641416575ade ]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b89bc283286b105e50aab9ab35992c0237ac77d8 ]
Add documentation for r8a77965 compatible string to rcar-dmac device
tree bindings documentation.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7de5b7e5f6a67c285b86d1478e8e150929c93482 ]
Add documentation for r8a77965 compatible string to Renesas sci-serial
device tree bindings documentation.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b614e905a0bc8fc5d4fa72665ac26ae00c874a4e ]
Bindings describe hardware, not drivers.
Use reference to hardware Allwinner A1X Pin Controller instead driver.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 99bf8f27f3f94d2a37291354b8dc83f13728f75f ]
The 'kiebackpeter' entry has been added to vendor-prefixes.txt to indicate
products from Kieback & Peter GmbH.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7e065fb9ccce89fe667fdbd9a177eaec59a359fc ]
Add missing pin group uart5nocts (all pins except cts), which has been
supported by the artpec6 pinctrl driver since its initial submission.
Fixes: 00df0582eab1 ("pinctrl: Add pincontrol driver for ARTPEC-6 SoC")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2e08e4d2ff488424919d69dd211ac860a019ac1d ]
The Allwinner H6 main CCU uses the internal oscillator of the SoC, which
is different with old SoCs' main CCU.
Add device tree binding for the Allwinner H6 main CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3cd2c313f1d618f92d1294addc6c685c17065761 ]
On the CP110 components which are present on the Armada 7K/8K SoC we need
to explicitly enable the clock for the registers. However it is not
needed for the AP8xx component, that's why this clock is optional.
With this patch both clock have now a name, but in order to be backward
compatible, the name of the first clock is not used. It allows to still
use this clock with a device tree using the old binding.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f597fbce38d230af95384f4a04e0a13a1d0ad45d upstream.
The Nuvoton UART is almost compatible with the 8250 driver when probed
via the 8250_of driver, however it requires some extra configuration
at startup.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c1b9d4c75cd549e08bd0596d7f9dcc20f7f6e8fa ]
The vendor name was "toppoly" but other panels and the vendor list
have defined it as "tpo". So let's fix it in driver and bindings.
We keep the old definition in parallel to stay compatible with
potential older DTB setup.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 015dbeb2282030bf56762e21d25f09422edfd750 upstream.
This patch adds support for r8a77965 (R-Car M3-N).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aece34cd576c7625181b0488a8129c1e165355f7 upstream.
Document a binding for the MIPS Cluster Power Controller (CPC) that
allows the device tree to specify where the CPC registers are located.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18512/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cdd10409914184c7eee5ae3e11beb890c9c16c61 upstream.
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f60 updated it incorrectly
while moving from platform code to DT. Fix it.
Cc: stable@vger.kernel.org # v3.10+
Fixes: 6e8887f60f60 ("ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f42ae7b0540937e00fe005812997f126aaac4bc2 ]
The USB hub port-number range for USB 2.0 is 1-255 and not 1-31 which
reflects an arbitrary limit set by the current Linux implementation.
Note that for USB 3.1 hubs the valid range is 1-15.
Increase the documented valid range in the binding to 255, which is the
maximum allowed by the specifications.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e20824e944c3bf4352fcd8d9f446c41b53901e7b ]
While the new family-specific compatible values introduced by commit
6f54cc1adcc8957f ("devicetree: bindings: R-Car Gen2 CMT0 and CMT1
bindings") use the recommended order "<vendor>,<family>-<device>", the
new SoC-specific compatible values still use the old and deprecated
order "<vendor>,<device>-<soc>".
Switch the SoC-specific compatible values to the recommended order while
there are no upstream users of these compatible values yet.
Fixes: 7f03a0ecfdc786c1 ("devicetree: bindings: r8a73a4 and R-Car Gen2 CMT bindings")
Fixes: 63d9e8ca0dd4bfa4 ("devicetree: bindings: Deprecate property, update example")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 68615eb01f82256c19e41967bfb3eef902f77033 upstream.
With a nxp,se97 chip on an atmel sama5d31 board, the I2C adapter driver
is not always capable of avoiding the 25-35 ms timeout as specified by
the SMBUS protocol. This may cause silent corruption of the last bit of
any transfer, e.g. a one is read instead of a zero if the sensor chip
times out. This also affects the eeprom half of the nxp-se97 chip, where
this silent corruption was originally noticed. Other I2C adapters probably
suffer similar issues, e.g. bit-banging comes to mind as risky...
The SMBUS register in the nxp chip is not a standard Jedec register, but
it is not special to the nxp chips either, at least the atmel chips
have the same mechanism. Therefore, do not special case this on the
manufacturer, it is opt-in via the device property anyway.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here are a small number of patches to resolve some reported IIO and a
staging driver problem. Nothing major here, full details are in the
shortlog below.
All have been in linux-next with no reported issues"
* tag 'staging-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: bcm2835-audio: Fix memory corruption
iio: adc: at91-sama5d2_adc: fix probe error on missing trigger property
iio: adc: dln2-adc: fix build error
iio: dummy: events: Add missing break
staging: iio: ade7759: fix signed extension bug on shift of a u8
iio: pressure: zpa2326: Remove always-true check which confuses gcc
iio: proximity: as3935: noise detection + threshold changes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.14-rc5 from Marc Zyngier:
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.14 cycle.
* ade7759
- Fix a signed extension bug.
* as3935
- The default noise and watch dog settings were such that the device
was unusuable in most applications. Add device tree parameters to
allow it to be configured to something that will actually work.
* at91-sama5d2 adc
- Fix handling of legacy device trees that don't provide the new
trigger edge property.
* dln2-adc
- Fix a missing Kconfig dependency on IIO_TRIGGERED_BUFFER.
* dummy driver
- Add a missing break so that writing in_voltage0_thresh_rising_en
doesn't always result in an error.
* zpa2326
- Drop a test for an always true condition so that gcc won't spit out
and unused variable warning.
|
|
Currently, the examples are using 2MB for the ITS size. Per the
specification (section 8.18 in ARM IHI 0069D), the ITS address map is
128KB.
Update the examples to match the specification.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
|
|
Pull networking fixes from David Miller:
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Without this patch the kernel hand during boot if the mvpp2.2 network
driver was not present in the kernel. Indeed the clock needed by the
xenon controller was set by the network driver.
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core
functionality)"
CC: Stable <stable@vger.kernel.org>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
into fixes
Reset controller fixes for v4.14
- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies
* tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add constants and callback functions for the dwmac on rk3128 soc.
As can be seen, the base structure is the same, only registers
and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a small number (5) of patches for some reported TTY and
serial issues. Nothing major, a documentation update, timing fix,
error handling fix, name reporting fix, and a timeout issue resolved.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sccnxp: Fix error handling in sccnxp_probe()
tty: serial: lpuart: avoid report NULL interrupt
serial: bcm63xx: fix timing issue.
mxser: fix timeout calculation for low rates
serial: sh-sci: document R8A77970 bindings
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Four fixes for the as3645a LED flash controller and one update to
MAINTAINERS"
* tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Add entry for MediaTek PMIC LED driver
as3645a: Unregister indicator LED on device unbind
as3645a: Use integer numbers for parsing LEDs
dt: bindings: as3645a: Use LED number to refer to LEDs
as3645a: Use ams,input-max-microamp as documented in DT bindings
|
|
Most applications are too noisy to allow the default noise and
watchdog settings, and thus need to be configurable via DT
properties.
Also default settings to POR defaults on a reset, and register
distuber interrupts as noise since it prevents proper usage.
Cc: devicetree@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix build for !OF providing empty of_find_device_by_node
- fix Abracon vendor prefix
- sync dtx_diff include paths (again)
- a stm32h7 clock binding doc fix
* tag 'devicetree-fixes-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: clk: stm32h7: fix clock-cell size
scripts/dtc: dtx_diff - 2nd update of include dts paths to match build
dt-bindings: fix vendor prefix for Abracon
of: provide inline helper for of_find_device_by_node
|
Neil Armstrong
Jitao Shi
Madalin Bucur
Geert Uytterhoeven
Baruch Siach
Florian Fainelli
Roger Quadros
allen yan
Josua Mayer
Sean Nyekjaer
Adrian Bunk
Lukas Wunner
Nicolas Ferre
Michal Vokáč
Yixun Lan
Martin Blumenstingl
Damien Thébault
Jacopo Mondi
Matheus Castello
Lukasz Majewski
Niklas Cassel
Icenowy Zheng
Gregory CLEMENT
Joel Stanley
H. Nikolaus Schaller
Yoshihiro Shimoda
Paul Burton
Viresh Kumar
Johan Hovold
Peter Rosin
Linus Torvalds
Thomas Gleixner
Greg Kroah-Hartman
Julien Grall
Gregory CLEMENT
Olof Johansson
David Wu
Matt Ranostay