Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- add wireless type
- properly document current direction
Battery/charger driver changes:
- new fuel-gauge/charger driver for RN5T618/RN5T619
- new charger driver for BQ25980, BQ25975 and BQ25960
- bq27xxx-battery: add support for TI bq34z100
- gpio-charger: convert to GPIO descriptors
- gpio-charger: add optional support for charge current limiting
- max17040: add support for max17041, max17043, max17044
- max17040: add support for max17048, max17049, max17058, max17059
- smb347-charger: add DT support
- smb247-charger: add SMB345 and SMB358 support
- simple-battery: add temperature properties
- lots of minor fixes, cleanups and DT binding YAML conversions
Reset drivers:
- ocelot: Add support for Sparx5"
* tag 'for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (81 commits)
power: reset: POWER_RESET_OCELOT_RESET should depend on Ocelot or Sparx5
power: supply: bq25980: Fix uninitialized wd_reg_val and overrun
power: supply: ltc2941: Fix ptr to enum cast
power: supply: test-power: revise parameter printing to use sprintf
power: supply: charger-manager: fix incorrect check on charging_duration_ms
power: supply: max17040: Fix ptr to enum cast
power: supply: bq25980: Fix uninitialized wd_reg_val
power: supply: bq25980: remove redundant zero check on ret
power: reset: ocelot: Add support for Sparx5
dt-bindings: reset: ocelot: Add Sparx5 support
power: supply: sbs-battery: keep error code when get_property() fails
power: supply: bq25980: Add support for the BQ259xx family
dt-binding: bq25980: Add the bq25980 flash charger
power: supply: fix spelling mistake "unprecise" -> "imprecise"
power: supply: test_power: add missing newlines when printing parameters by sysfs
power: supply: pm2301: drop duplicated i2c_device_id
power: supply: charger-manager: drop unused charger assignment
power: supply: rt9455: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: goldfish: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: bq25890: skip 'struct acpi_device_id' when !CONFIG_ACPI
...
|
|
In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As common/shared
schema are included by other schemas, they should always allow for
additionalProperties.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201005183830.486085-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Another round of wack-a-mole. The json-schema default is additional
unknown properties are allowed, but for DT all properties should be
defined.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewd-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20201002234143.3570746-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add yaml for the bq25980 flash charger.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
To compensate for the battery chemistry and operating conditions the
chips support a compensation value. Specify one or two byte compensation
via the maxim,rcomp byte array.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Maxim max17040 is a fuel gauge from a larger family utilising the Model
Gauge technology. Document all different compatible strings that the
max17040 driver recognizes.
Some devices in the wild report double the capacity. The
maxim,double-soc (from State-Of-Charge) property fixes that.
Examples: https://lore.kernel.org/patchwork/patch/1263411/#1468420
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add compatible for bq34z100 charger.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Document new properties for IBAT compensation feature.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This binding can support Ingenic JZ4725B and JZ4770 SoCs, as they are
compatible with Ingenic JZ4740 battery.
Introduce the following compatible property combinations:
compatible = "ingenic,jz4725b-battery", "ingenic,jz4740-battery",
compatible = "ingenic,jz4770-battery", "ingenic,jz4740-battery"
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Convert the textual documentation of Device Tree bindings for the
Ingenic JZ47xx SoCs battery to YAML.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200908145922.4502-1-krzk@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The bindings for charger-manager were very unclear and didn't
specify allowable values in many cases. Clean these up to show
what each value does and make sure all properties are documented
here rather than using wildcards.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add new charge-current-limit feature to gpio-charger.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Summit SMB3xx series is a Programmable Switching Li+ Battery Charger.
This patch adds device-tree binding for Summit SMB345, SMB347 and SMB358
chargers.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Document generic battery temperature properties.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Clean-up incorrect indentation, extra spaces, long lines, and missing
EOF newline in schema files. Most of the clean-ups are for list
indentation which should always be 2 spaces more than the preceding
keyword.
Found with yamllint (which I plan to integrate into the checks).
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-clk@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-spi@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-remoteproc@vger.kernel.org
Cc: linux-hwmon@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add the Texas Instruments bq28z610 battery monitor to the bq27xxx
binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add the Texas Instruments bq27z561 battery monitor to the bq27xxx
binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Convert the battery.txt file to yaml and fix up the examples.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[Fixed the regex for ocv-capacity-table and the DT example for it]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The BQ2515X family of devices are highly integrated battery management
ICs that integrate the most common functions for wearable devices
namely a charger, an output voltage rail, ADC for battery and system
monitoring, and a push-button controller.
Datasheets:
http://www.ti.com/lit/ds/symlink/bq25150.pdf
http://www.ti.com/lit/ds/symlink/bq25155.pdf
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
While strongly recommended, not all devices have a gpio to
detect if the charger is connected. This moves the 'gpios'
from required to optional section.
This also modifies error handling for the GPIO a bit: We
no longer fallback to pdata, if a GPIO is specified using
GPIO descriptor tables. This is a bit cleaner and does
not have any real impact: There are only two mainline pdata
users (arm/mach-sa1100/collie.c, arm/mach-pxa/tosa.c) and
none of them specify the GPIO via gpiod descriptor tables.
Once both have been converted the driver's support for
specifying GPIOs numbers in pdata will be dropped.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Convert the gpio-charger bindings from text format to
new YAML based representation.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The driver requires interrupts (fails probe if it is not provided) so
document this requirement in bindings.
Fixes: 4aeae9cb0dad ("power_supply: Add support for TI BQ25890 charger chip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Fix example indentation to tabs to follow generic Linux coding style.
This avoids copying the space indentation to DTS when re-using the
example.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Another round of 'allOf' removals that came in this cycle.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Convert sbs-battery bindings to YAML.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In certain designs, it is possible to add a battery on a populated i2c
bus without an sbs compliant charger. In that case, the battery will
unnecessarily and sometimes undesirably master the bus trying to write
info in the charger.
It is observed in many occasion that these battery "broadcasts" are even
corrupting other ongoing master to slave communication. I.e. the
multi-master support in the battery is inadequate.
Thankfully, the CHARGER_MODE bit allows designers to disable that SBS
battery behaviour.
This needs to be done once when the battery is first seen on the bus.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
[rebased code]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for BQ20Z65 manufacturer data to the sbs-battery
driver. Implementation has been verified using the public TRM
available from [0] and tested using a GE Flex 3S2P battery.
[0] http://www.ti.com/lit/pdf/sluu386
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Convert the bq27xxx.txt to yaml format
CC: Pali Rohár <pali@kernel.org>
CC: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery. Intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.
Document the DT bindings for BD99954
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add:
- trickle-charge-current-microamp:
Some chargers have 3 charging stages. First one when battery is almost
empty is often called as trickle-charge. Last state when battery has been
"woken up" is usually called as fast-charge. In addition to this some
chargers have a 'middle state' which ROHM BD99954 data-sheet describes as
pre-charge. Some batteries can benefit from this 3-phase charging
[citation needed].
Introduce trickle-charge-current-microamp so that batteries can give
charging current limit for all three states.
- precharge-upper-limit-microvolt:
When battery voltage has reached certain limit we change from
trickle-charge to next charging state (pre-charge for BD99954). Allow
battery to specify this limit.
- re-charge-voltage-microvolt:
Allow giving a battery specific voltage limit for chargers which can
automatically re-start charging when battery has discharghed down to
this limit.
- over-voltage-threshold-microvolt
Allow specifying voltage threshold after which the battery is assumed to
be faulty.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This patch adds the dts binding schema for the cw2015 fuel gauge.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Convert the power_supply.txt to power-supply.yaml.
This conversion entailed fixing up the binding to being yaml and dt
checker compliant.
Added a note in the power_supply.txt to reference the power-supply.yaml
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Setting 'additionalProperties: false' is frequently omitted, but is
important in order to check that there aren't extra undocumented
properties in a binding.
Ideally, we'd just add this automatically and make this the default, but
there's some cases where it doesn't work. For example, if a common
schema is referenced, then properties in the common schema aren't part
of what's considered for 'additionalProperties'. Also, sometimes there
are bus specific properties such as 'spi-max-frequency' that go into
bus child nodes, but aren't defined in the child node's schema.
So let's stick with the json-schema defined default and add
'additionalProperties: false' where needed. This will be a continual
review comment and game of wack-a-mole.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Stephen Boyd <sboyd@kernel.org> # clock
Acked-by: Lee Jones <lee.jones@linaro.org>
|
|
Add bq25892, bq25895 and bq25896 to list of supported device IDs in the
bq25890 DT binding document.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Documentation of max17040 based fuel gauge characteristics.
For configure low level state of charge threshold alert signaled from
max17043/max17044 we add "maxim,alert-low-soc-level" property.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
resistance of coulomb counter chip
Add a new property to describe the real resistance of coulomb counter chip,
which is used to calibrate the accuracy of the coulomb counter chip.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
resistance with temperature changes
Since the battery internal resistance can be changed as the temperature
changes, thus add one table to describe the battery resistance percent
in different temperatures to get a accurate battery internal resistance.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The bindings are missing documentation for some of the compatible
strings.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
|
|
Convert the binding document for MAX77650 charger module to YAML.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
There have been some cases of droid4 battery bulging that seem to be
related to being left connected to the charger for several weeks.
It is suspected that the 4.35V charge voltage configured for the battery
is too much in the long run, so lets limit the charge voltage to 4.2V.
It could also be that the batteries are just getting old.
We don't really want to just change the charge voltage to 4.2V as Android
may have charged the battery to 4.35V as pointed out by Pavel Machek.
To add checks for battery voltage, the driver needs to understand the
voltage it's charging at, and also needs to better understand it's
charger state. Right now it only understands connect and disconnect,
while now we need to know also a connected state but not charging.
So let's add better charger state handling with help of chrgcurr2 interrupt
for detecting charge full and retry, and add a check for battery voltage
before we start charging. And then we finally can lower the charge voltage
to 4.2V.
Note that we've been using the same register values as the Android distros
on droid4, so it is suspected that the same problem also exists in Android.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add over-current health state
- Add standard, adaptive and custom charge types
- Add new properties for start/end charge threshold
New Drivers / Hardware:
- UCS1002 Programmable USB Port Power Controller
- Ingenic JZ47xx Battery Fuel Gauge
- AXP20x USB Power: Add AXP813 support
- AT91 poweroff: Add SAM9X60 support
- OLPC battery: Add XO-1.5 and XO-1.75 support
Misc Changes:
- syscon-reboot: support mask property
- AXP288 fuel gauge: Blacklist ACEPC T8/T11. Looks like some vendor
thought it's a good idea to build a desktop system with a fuel
gauge, that slowly "discharges"...
- cpcap-battery: Fix calculation errors
- misc fixes"
* tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (54 commits)
power: supply: olpc_battery: force the le/be casts
power: supply: ucs1002: Fix build error without CONFIG_REGULATOR
power: supply: ucs1002: Fix wrong return value checking
power: supply: Add driver for Microchip UCS1002
dt-bindings: power: supply: Add bindings for Microchip UCS1002
power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
power: supply: core: fix clang -Wunsequenced
power: supply: core: Add missing documentation for CHARGE_CONTROL_* properties
power: supply: core: Add CHARGE_CONTROL_{START_THRESHOLD,END_THRESHOLD} properties
power: supply: core: Add Standard, Adaptive, and Custom charge types
power: supply: axp288_fuel_gauge: Add ACEPC T8 and T11 mini PCs to the blacklist
power: supply: bq27xxx_battery: Notify also about status changes
power: supply: olpc_battery: Have the framework register sysfs files for us
power: supply: olpc_battery: Add OLPC XO 1.75 support
power: supply: olpc_battery: Avoid using platform_info
power: supply: olpc_battery: Use devm_power_supply_register()
power: supply: olpc_battery: Move priv data to a struct
power: supply: olpc_battery: Use DT to get battery version
x86/platform/olpc: Use a correct version when making up a battery node
x86/platform/olpc: Trivial code move in DT fixup
...
|
|
Add the DT binding document for the battery charger module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add bindings for Microchip UCS1002 Programmable USB Port Power
Controller with Charger Emulation.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This immutable branch contains the changes required for OLPC
1.75 battery, which touches x86 and power-supply and is based
on v5.1-rc1.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The XO-1 and XO-1.5 batteries apparently differ in an ability to report
ambient temperature.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add documentation for the ingenic-battery driver, used on JZ47xx SoCs.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This adds the "x-powers,axp813-usb-power-supply" to the list of
compatibles for AXP20X VBUS power supply driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add documentation for the "charge-status-gpios" property.
Update the "gpios" property with a valid example.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|