| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit 5d7400c4acbf7fe633a976a89ee845f7333de3e4 upstream.
Always stating PIN_CONFIG_BIAS_DISABLE is supported gives untrue output
when examining /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins if
the operation get_bias() is implemented but the pin is not handled by
the get_bias() implementation. In that case the output will state that
"input bias disabled" indicating that this pin has bias control
support.
Make support for PIN_CONFIG_BIAS_DISABLE depend on that the pin either
supports SH_PFC_PIN_CFG_PULL_UP or SH_PFC_PIN_CFG_PULL_DOWN. This also
solves the issue where SoC specific implementations print error messages
if their particular implementation of {set,get}_bias() is called with a
pin it does not know about.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69d012345a1a32d3f03957f14d972efccc106a98 upstream.
In current code, the @changed always returns the last one's status for
the huge page with the contiguous bit set. This is really not what we
want. Even one of the PTEs is changed, we should tell it to the caller.
This patch fixes this issue.
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 20156ce2365d61beaa6f5a78a7a789044e0e7acc upstream.
The find_num_contig() will return 1 when the pmd is not present.
It will cause a kernel dead loop in the following scenaro:
1.) pmd entry is not present.
2.) the page fault occurs:
... hugetlb_fault() --> hugetlb_no_page() --> set_huge_pte_at()
3.) set_huge_pte_at() will only set the first PMD entry, since the
find_num_contig just return 1 in this case. So the PMD entries
are all empty except the first one.
4.) when kernel accesses the address mapped by the second PMD entry,
a new page fault occurs:
... hugetlb_fault() --> huge_ptep_set_access_flags()
The second PMD entry is still empty now.
5.) When the kernel returns, the access will cause a page fault again.
The kernel will run like the "4)" above.
We will see a dead loop since here.
The dead loop is caught in the 32M hugetlb page (2M PMD + Contiguous bit).
This patch removes wrong pmd check, and fixes this dead loop.
This patch also removes the redundant checks for PGD/PUD in
the find_num_contig().
Acked-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c2f0afe3582c58efeef93bc57bc07d502132618 upstream.
The libhugetlbfs meets several failures since the following functions
do not use the correct address:
huge_ptep_get_and_clear()
huge_ptep_set_access_flags()
huge_ptep_set_wrprotect()
huge_ptep_clear_flush()
This patch fixes the wrong address for them.
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4791db527bf397c84c9956c3ece9692ed5322ac upstream.
Whenever a PE is initialised in powernv, opal_pci_eeh_freeze_clear() is
called. This is to remove any existing freeze, and has no negative side
effects if the PE is already in an unfrozen state. On PHB backends that
don't support this operation and return OPAL_UNSUPPORTED, this creates a
scary and misleading warning message.
Skip the warning message on init if OPAL_UNSUPPORTED is returned.
As far as I'm aware, this currently only affects NPUs.
Fixes: 313483d ("powerpc/powernv: Unfreeze PE on allocation")
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe0f3168169f7c34c29b0cf0c489f126a7f29643 upstream.
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff53 ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 815a7141c4d1b11610dccb7fcbb38633759824f2 upstream.
Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc9962f ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 555c16328ae6d75a90e234eac9b51998d68f185b upstream.
Version 3.00 of the ISA states that the PATS (partition table size) field
of the PTCR (partition table control register) and the PRTS (process table
size) field of the partition table entry must both be less than or equal
to 24. However the actual size of the partition and process tables is equal
to 2 to the power of 12 plus the PATS and PRTS fields, respectively. This
means that the max allowable size of each of these tables is 2^36 or 64GB
for both.
Thus when checking the size shift for each we should be checking for values
of greater than 36 instead of the current check for shifts larger than 24
and 23.
Fixes: 2bfd65e45e877fb5704730244da67c748d28a1b8
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c090959b9dd8c87703e275079aa4b4a824ba3f8e upstream.
Make sure to drop the reference to the parent device taken by
class_find_device() after populating the bus.
Fixes: 3b9334ac835b ("mfd: vexpress: Convert custom func API to regmap")
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c02ebfdddbafa9a6a0f52fbd715e6bfa229af9d3 upstream.
Commit 0e87e58bf60e ("blk-mq: improve warning for running a queue on the
wrong CPU") attempts to avoid triggering the WARN_ON in
__blk_mq_run_hw_queue when the expected CPU is dead. Problem is, in the
last batch execution before round robin, blk_mq_hctx_next_cpu can
schedule a dead CPU and also update next_cpu to the next alive CPU in
the mask, which will trigger the WARN_ON despite the previous
workaround.
The following patch fixes this scenario by always scheduling the value
in hctx->next_cpu. This changes the moment when we round-robin the CPU
running the hctx, but it really doesn't matter, since it still executes
BLK_MQ_CPU_WORK_BATCH times in a row before switching to another CPU.
Fixes: 0e87e58bf60e ("blk-mq: improve warning for running a queue on the wrong CPU")
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3bee9ea1de687925d116670f036599cbed8b66b0 upstream.
The BQ27510 and BQ27520 use a slightly different register map than the
BQ27500, add a new type enum and add these gauges to it.
Fixes: d74534c27775 ("power: bq27xxx_battery: Add support for additional bq27xxx family devices")
Based-on-patch-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 075eb5719d53e8bb4a406ad87e1de99319aa50f0 upstream.
There's a typo, it should do pm_runtime_get_sync, not put.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Cc: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15f7e3c21b76598bc6e5816d2577ce843b2b963f upstream.
Fix to return error code -ENOMEM from the __get_free_page() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 05eb23893c2c ("cxgb4/iw_cxgb4: Doorbell Drop Avoidance Bug Fixes")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb43f81b8489dcb87555e16c17453f0a9fa690f2 upstream.
Commit e1399ba20eee ("powercap / RAPL: handle missing MSRs") added
contraint_to_pl() function to return index into an array. But it
can potentially return -EINVAL if powercap layer sends an out of
range constraint ID. This patch adds sanity check.
Unnecessary RAPL domain pointer check is removed since it must be
initialized before calling rapl_unit_xlate().
Fixes: e1399ba20eee ("powercap / RAPL: handle missing MSRs")
Reported-by: Odzioba, Lukasz <lukasz.odzioba@intel.com>
Reported-by: Koss, Marcin <marcin.koss@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a545715d2dae8d071c5b06af947b07ffa846b288 upstream.
When removing and adding cpu 0 on a system with GHES NMI the following stack
trace is seen when re-adding the cpu:
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/apic/apic.c:1349 setup_local_APIC+
Modules linked in: nfsv3 rpcsec_gss_krb5 nfsv4 nfs fscache coretemp intel_ra
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6+ #2
Call Trace:
dump_stack+0x63/0x8e
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
setup_local_APIC+0x275/0x370
apic_ap_setup+0xe/0x20
start_secondary+0x48/0x180
set_init_arg+0x55/0x55
early_idt_handler_array+0x120/0x120
x86_64_start_reservations+0x2a/0x2c
x86_64_start_kernel+0x13d/0x14c
During the cpu bringup, wakeup_cpu_via_init_nmi() is called and issues an
NMI on CPU 0. The GHES NMI handler, ghes_notify_nmi() runs the
ghes_proc_irq_work work queue which ends up setting IRQ_WORK_VECTOR
(0xf6). The "faulty" IR line set at arch/x86/kernel/apic/apic.c:1349 is also
0xf6 (specifically APIC IRR for irqs 255 to 224 is 0x400000) which confirms
that something has set the IRQ_WORK_VECTOR line prior to the APIC being
initialized.
Commit 2383844d4850 ("GHES: Elliminate double-loop in the NMI handler")
incorrectly modified the behavior such that the handler returns
NMI_HANDLED only if an error was processed, and incorrectly runs the ghes
work queue for every NMI.
This patch modifies the ghes_proc_irq_work() to run as it did prior to
2383844d4850 ("GHES: Elliminate double-loop in the NMI handler") by
properly returning NMI_HANDLED and only calling the work queue if
NMI_HANDLED has been set.
Fixes: 2383844d4850 (GHES: Elliminate double-loop in the NMI handler)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebc4ff661fbe76781c6b16dfb7b754a5d5073f8e upstream.
cfq_cpd_alloc() which is the cpd_alloc_fn implementation for cfq was
incorrectly hard coding GFP_KERNEL instead of using the mask specified
through the @gfp parameter. This currently doesn't cause any actual
issues because all current callers specify GFP_KERNEL. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: e4a9bde9589f ("blkcg: replace blkcg_policy->cpd_size with ->cpd_alloc/free_fn() methods")
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a05e7541c39680d28ecf91892338e074738d5fd upstream.
With compilers which follow the C99 standard (like modern versions of
gcc and clang), "extern inline" does the opposite thing from older
versions of gcc (emits code for an externally linkable version of the
inline function).
"static inline" does the intended behavior in all cases instead.
Description taken from commit 6d91857d4826 ("staging, rtl8192e,
LLVMLinux: Change extern inline to static inline").
This also fixes the following GCC warning when building with CONFIG_PM
disabled:
./include/linux/blkdev.h:1143:20: warning: no previous prototype for 'blk_set_runtime_active' [-Wmissing-prototypes]
Fixes: d07ab6d11477 ("block: Add blk_set_runtime_active()")
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 501634759d55a5b56967de6d9465acf02bbc3565 upstream.
We should return -EINVAL (instead of 0) if get_cpu_device() fails.
Fixes: 158c998ea44b (ACPI / CPPC: add sysfs support to compute delivered performance)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85b037442e3f0e84296ab1010fd6b057eee18496 upstream.
The handling of bypass_val_on that was added in
regulator_get_bypass_regmap is done unconditionally however
several drivers don't define a value for bypass_val_on. This
results in those drivers reporting bypass being enabled when
it is not. In regulator_set_bypass_regmap we use bypass_mask
if bypass_val_on is zero. This patch adds similar handling in
regulator_get_bypass_regmap.
Fixes: commit dd1a571daee7 ("regulator: helpers: Ensure bypass register field matches ON value")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a10c06a20ec8097a68fd7a4a1c0e285095b4d2f upstream.
With preemption turned on we can read incorrect throttling state
while being switched to CPU on a different chip.
BUG: using smp_processor_id() in preemptible [00000000] code: cat/7343
caller is .powernv_cpufreq_throttle_check+0x2c/0x710
CPU: 13 PID: 7343 Comm: cat Not tainted 4.8.0-rc5-dirty #1
Call Trace:
[c0000007d25b75b0] [c000000000971378] .dump_stack+0xe4/0x150 (unreliable)
[c0000007d25b7640] [c0000000005162e4] .check_preemption_disabled+0x134/0x150
[c0000007d25b76e0] [c0000000007b63ac] .powernv_cpufreq_throttle_check+0x2c/0x710
[c0000007d25b7790] [c0000000007b6d18] .powernv_cpufreq_target_index+0x288/0x360
[c0000007d25b7870] [c0000000007acee4] .__cpufreq_driver_target+0x394/0x8c0
[c0000007d25b7920] [c0000000007b22ac] .cpufreq_set+0x7c/0xd0
[c0000007d25b79b0] [c0000000007adf50] .store_scaling_setspeed+0x80/0xc0
[c0000007d25b7a40] [c0000000007ae270] .store+0xa0/0x100
[c0000007d25b7ae0] [c0000000003566e8] .sysfs_kf_write+0x88/0xb0
[c0000007d25b7b70] [c0000000003553b8] .kernfs_fop_write+0x178/0x260
[c0000007d25b7c10] [c0000000002ac3cc] .__vfs_write+0x3c/0x1c0
[c0000007d25b7cf0] [c0000000002ad584] .vfs_write+0xc4/0x230
[c0000007d25b7d90] [c0000000002aeef8] .SyS_write+0x58/0x100
[c0000007d25b7e30] [c00000000000bfec] system_call+0x38/0xfc
Fixes: 09a972d16209 (cpufreq: powernv: Report cpu frequency throttling)
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b243fcfb5f1e16bcf732e6f86a63f8af5b59a9f upstream.
This changes the way that we support the new ISA v3.00 HPTE format.
Instead of adapting everything that uses HPTE values to handle either
the old format or the new format, depending on which CPU we are on,
we now convert explicitly between old and new formats if necessary
in the low-level routines that actually access HPTEs in memory.
This limits the amount of code that needs to know about the new
format and makes the conversions explicit. This is OK because the
old format contains all the information that is in the new format.
This also fixes operation under a hypervisor, because the H_ENTER
hypercall (and other hypercalls that deal with HPTEs) will continue
to require the HPTE value to be supplied in the old format. At
present the kernel will not boot in HPT mode on POWER9 under a
hypervisor.
This fixes and partially reverts commit 50de596de8be
("powerpc/mm/hash: Add support for Power9 Hash", 2016-04-29).
Fixes: 50de596de8be ("powerpc/mm/hash: Add support for Power9 Hash")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d701d3dd8caf6660ff33c3c23a115b4649c5cdb upstream.
Fix to return a negative error code from the st_rproc_state() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 63edb0310a5c ("remoteproc: Supply controller driver for ST's Remote Processors")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6de1a507c46bf22ed97043495b9ab96e4d5c213b upstream.
The tie between the main WCNSS driver and the IRIS driver causes a
circular dependency between the two modules. Neither part makes sense to
have on their own so lets merge them into one module.
For the sake of picking up the clock and regulator resources described
in the iris of_node we need an associated struct device. But, to keep
the size of the patch down we continue to represent the IRIS part as its
own platform_driver, within the same module, rather than setting up a
dummy device.
Fixes: aed361adca9f ("remoteproc: qcom: Introduce WCNSS peripheral image loader")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc98e6ce6abe1c0103cbd7aff1ee586622a9361e upstream.
commit 202b52b7fbf7 ("drm: Track drm_mm nodes with an interval tree")
introduced a requirement that the special drm_mm.head_node was
initialised and marked as not being allocated. It is a very special node
that has no side but has a hole that represents the drm_mm address
space, and holds the list of nodes. Since it is not a real node, it is
not part of the node rbtree and we detect this as it being unallocated.
This presumed that drm_mm_init() was initialising it to zero. It happens
that i915 kzallocs its objects and so it was accidentally setting it,
but for generic use we cannot make that assumption.
[ 22.981519] general protection fault: 0000 [#1] SMP
[ 22.981521] Modules linked in: test_drm_mm(+) ctr ccm arc4 rt2800usb rt2x00usb rt2800lib rt2x00lib crc_ccitt mac80211 cmac rfcomm bnep snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic snd_hda_intel dcdbas snd_hda_codec x86_pkg_temp_thermal intel_powerclamp btusb snd_hda_core coretemp crct10dif_pclmul cfg80211 btrtl btbcm btintel bluetooth crc32_pclmul ghash_clmulni_intel aesni_intel snd_pcm i2c_hid aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd snd_timer hid_multitouch snd joydev serio_raw lpc_ich mfd_core i2c_designware_platform i2c_designware_core 8250_dw binfmt_misc soundcore acpi_pad nls_iso8859_1 usbhid hid psmouse ahci libahci [last unloaded: test_drm_mm]
[ 22.981544] CPU: 1 PID: 2088 Comm: drm_mm Tainted: G W 4.9.0-rc7+ #234
[ 22.981545] Hardware name: Dell Inc. XPS 13 9343/0310JH, BIOS A07 11/11/2015
[ 22.981546] task: ffff88020c971cc0 task.stack: ffffc90001728000
[ 22.981547] RIP: 0010:[<ffffffff814050f0>] [<ffffffff814050f0>] drm_mm_interval_tree_add_node+0xa0/0xd0
[ 22.981551] RSP: 0018:ffffc9000172ba98 EFLAGS: 00010202
[ 22.981552] RAX: 0f0000c69cf63d80 RBX: ffff88020be00000 RCX: ffff88020be00000
[ 22.981553] RDX: 0000000000000fff RSI: ffffc9000172bc48 RDI: ffffffff810ac4df
[ 22.981553] RBP: ffffc9000172bb08 R08: ffffc9000172bc70 R09: 0000000000000fff
[ 22.981554] R10: ffffffff810ac4d7 R11: 4dc04d8b4cffffe5 R12: 0000000000001000
[ 22.981555] R13: ffffc9000172bbd0 R14: ffffc9000172bbe0 R15: 0000000002000000
[ 22.981556] FS: 00007f80c9fab740(0000) GS:ffff88021f480000(0000) knlGS:0000000000000000
[ 22.981557] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 22.981558] CR2: 00007f80c9fd5000 CR3: 000000020c191000 CR4: 00000000003406e0
[ 22.981559] Stack:
[ 22.981560] ffffffff81405d09 ffff88020be00000 ffffc9000172bbe0 000000000172bb08
[ 22.981562] ffffffffffffffff 0000000000000000 0000000000000000 0000000000000000
[ 22.981563] 0000000002000000 0000000002000000 ffffffffa02f3000 ffff88020be00000
[ 22.981565] Call Trace:
[ 22.981568] [<ffffffff81405d09>] ? drm_mm_insert_node_generic+0x229/0x310
[ 22.981570] [<ffffffffa02f3000>] ? 0xffffffffa02f3000
[ 22.981572] [<ffffffffa02903c1>] __subtest_insert_range.constprop.7+0xd1/0x5b0 [test_drm_mm]
[ 22.981575] [<ffffffff81081222>] ? default_wake_function+0x12/0x20
[ 22.981576] [<ffffffff81096905>] ? __wake_up_common+0x55/0x90
[ 22.981578] [<ffffffff81085f42>] ? sched_clock_cpu+0x72/0xa0
[ 22.981581] [<ffffffff811308ad>] ? irq_work_queue+0xd/0x80
[ 22.981582] [<ffffffff810abcc4>] ? wake_up_klogd+0x34/0x40
[ 22.981584] [<ffffffff810ac19d>] ? console_unlock+0x4cd/0x530
[ 22.981585] [<ffffffff810ac4d7>] ? vprintk_emit+0x2d7/0x490
[ 22.981587] [<ffffffff810ac82f>] ? vprintk_default+0x1f/0x30
[ 22.981589] [<ffffffff81146e1c>] ? printk+0x4d/0x4f
[ 22.981590] [<ffffffffa02f3000>] ? 0xffffffffa02f3000
[ 22.981592] [<ffffffffa02908b5>] subtest_insert_range+0x15/0x80 [test_drm_mm]
[ 22.981594] [<ffffffffa02f3088>] test_drm_mm_init+0x88/0x1000 [test_drm_mm]
[ 22.981597] [<ffffffff8100043d>] do_one_initcall+0x3d/0x150
[ 22.981600] [<ffffffff8119dfbf>] ? kfree+0x13f/0x180
[ 22.981602] [<ffffffff811471f2>] do_init_module+0x60/0x1f1
[ 22.981606] [<ffffffff810db878>] load_module+0x2228/0x2790
[ 22.981608] [<ffffffff810d8590>] ? __symbol_put+0x40/0x40
[ 22.981612] [<ffffffff811c52b1>] ? kernel_read+0x41/0x60
[ 22.981614] [<ffffffff810dbfb6>] SYSC_finit_module+0x96/0xd0
[ 22.981617] [<ffffffff810dc00e>] SyS_finit_module+0xe/0x10
[ 22.981620] [<ffffffff816e7aa4>] entry_SYSCALL_64_fastpath+0x17/0x98
[ 22.981622] Code: c7 41 30 00 00 00 00 48 89 e5 48 89 3a 48 c7 c2 20 4e 40 81 e8 b2 a1 f0 ff 5d c3 48 8d 56 78 45 31 d2 48 89 d6 eb 25 48 8b 51 58 <48> 39 50 38 73 04 48 89 50 38 4c 8b 58 28 4c 39 59 48 48 8d 50
[ 22.981651] RIP [<ffffffff814050f0>] drm_mm_interval_tree_add_node+0xa0/0xd0
[ 22.981655] RSP <ffffc9000172ba98>
Testcase: igt/drm_mm
Fixes: 202b52b7fbf7 ("drm: Track drm_mm nodes with an interval tree")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.9-rc1+
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161130205126.31106-1-chris@chris-wilson.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00b2b7288299a8c73c0c37b531a075ba5c849e67 upstream.
Trying to determine the pixel rate of the pipe can't be done until we
know the clock, which means it can't be done until the encoder
.get_config() hooks have been called. So let's move the min_pixclk[]
stuff to the end of intel_modeset_readout_hw_state() when we actually
have gathered all the required infromation.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 565602d7501a ("drm/i915: Do not acquire crtc state to check clock during modeset, v4.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161220153902.15621-1-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit aca1ebf491518910df156f3dab6a66306bb52e28)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 230c5b44233ff0543c0b5ccf4ff9400057010fbe upstream.
In the loop on .timings, we should check .num_timings to see if it's the
only mode specified, not .num_modes, which should be used with .modes.
Fixes: cda553725c92 ("drm/panel: simple: Set appropriate mode type")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cff52e5fc4cfc978b7df898dc14a0492c7ef0ae8 upstream.
gcc warns about the timestamp in drm_wait_vblank being possibly
used without an initialization:
drivers/gpu/drm/drm_irq.c: In function 'drm_crtc_send_vblank_event':
drivers/gpu/drm/drm_irq.c:992:24: error: 'now.tv_usec' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/gpu/drm/drm_irq.c:1069:17: note: 'now.tv_usec' was declared here
drivers/gpu/drm/drm_irq.c:991:23: error: 'now.tv_sec' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This can happen if drm_vblank_count_and_time() returns 0 in its
error path. To sanitize the error case, I'm changing that function
to return a zero timestamp when it fails.
Fixes: e6ae8687a87b ("drm: idiot-proof vblank")
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161017221355.1861551-6-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dccf82ad1775f2b9c36ec85e25e39d88c7e86818 upstream.
According to the previous patch, it's possible atm that we call
intel_do_sagv_disable() only once during the 1ms period and time out if
that call fails. As opposed to this the spec says that we need to keep
retrying this request for a 1ms duration, so let's do this similarly to
the CDCLK change notification request.
v4-5:
- Rebased on the reply_mask, reply change.
v6:
- Remove w/s change. (Lyude)
- Rebased on the timeout_base argument change.
Cc: Lyude <cpaul@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 656d1b89e5ff ("drm/i915/skl: Add support for the SAGV, fix underrun hangs")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude <lyude@redhat.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-2-git-send-email-imre.deak@intel.com
(cherry picked from commit b3b8e99984a4eace91bc097e8f8cec71441cae16)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f638c1cb0a1112dbe0b682a42db30521646686b upstream.
smbus functions return -ve on error, 0 on success. However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater.)
The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.
Fix this by making pca954x_reg_write() return a negative error code for
all failure cases.
Fixes: 463e8f845cbf ("i2c: mux: pca954x: retry updating the mux selection on failure")
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfd278c280f997cf2fe4662e0acab0fe465f637b upstream.
Various places assume that if nfs4_fl_prepare_ds() turns a non-NULL 'ds',
then ds->ds_clp will also be non-NULL.
This is not necessasrily true in the case when the process received a fatal signal
while nfs4_pnfs_ds_connect is waiting in nfs4_wait_ds_connect().
In that case ->ds_clp may not be set, and the devid may not recently have been marked
unavailable.
So add a test for ds_clp == NULL and return NULL in that case.
Fixes: c23266d532b4 ("NFS4.1 Fix data server connection race")
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Olga Kornievskaia <aglo@umich.edu>
Acked-by: Adamson, Andy <William.Adamson@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79f687a3de9e3ba2518b4ea33f38ca6cbe9133eb upstream.
Ben Coddington reports that commit 311324ad1713, by adding the function
nfs_dir_mapping_need_revalidate() that checks page cache validity on
each call to nfs_readdir() causes a performance regression when
the directory is being modified.
If the directory is changing while we're iterating through the directory,
POSIX does not require us to invalidate the page cache unless the user
calls rewinddir(). However, we still do want to ensure that we use
readdirplus in order to avoid a load of stat() calls when the user
is doing an 'ls -l' workload.
The fix should be to invalidate the page cache immediately when we're
setting the NFS_INO_ADVISE_RDPLUS bit.
Reported-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: 311324ad1713 ("NFS: Be more aggressive in using readdirplus...")
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee284e35d8c71bf5d4d807eaff6f67a17134b359 upstream.
We must put the task to sleep while holding the inode->i_lock in order
to ensure atomicity with the test for NFS_LAYOUT_RETURN.
Fixes: 500d701f336b ("NFS41: make close wait for layoutreturn")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f36ab161bebe464d33b998294eff29b17a9c8918 upstream.
Fix typo in parameter description.
Fixes: 5405fc44c337 ("NFSv4.x: Add kernel parameter to control the
callback server")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f24d311f92b516a8aadef5056424ccabb4068e7b upstream.
The pinctrl_gpio_request is called with the "full" gpio number, already
containing the base, then meson_pmx_request_gpio is then called with the
final pin number.
Remove the base addition when calling meson_pmx_disable_other_groups.
Fixes: 6ac730951104 ("pinctrl: add driver for Amlogic Meson SoCs")
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa7c8da35d1905d80e840d075f07d26ec90144b5 upstream.
In __btrfs_run_delayed_refs, the error path when run_delayed_extent_op
fails sets locked_ref->processing = 0 but doesn't re-increment
delayed_refs->num_heads_ready. As a result, we end up triggering
the WARN_ON in btrfs_select_ref_head.
Fixes: d7df2c796d7 (Btrfs: attach delayed ref updates to delayed ref heads)
Reported-by: Jon Nelson <jnelson-suse@jamponi.net>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0280996437081dd12ed1e982ac8aeaa62835ec4 upstream.
In __btrfs_run_delayed_refs, when we put back a delayed ref that's too
new, we have already dropped the lock on locked_ref when we set
->processing = 0.
This patch keeps the lock to cover that assignment.
Fixes: d7df2c796d7 (Btrfs: attach delayed ref updates to delayed ref heads)
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5a10c5f7532b7473776da87e67f8301bbc32693 upstream.
Commit 54adc01055b7 ("nvme/quirk: Add a delay before checking for adapter
readiness") introduced a quirk to adapters that cannot read the bit
NVME_CSTS_RDY right after register NVME_REG_CC is set; these adapters
need a delay or else the action of reading the bit NVME_CSTS_RDY could
somehow corrupt adapter's registers state and it never recovers.
When this quirk was added, we checked ctrl->tagset in order to avoid
quirking in probe time, supposing we would never require such delay
during probe. Well, it was too optimistic; we in fact need this quirk
at probe time in some cases, like after a kexec.
In some experiments, after abnormal shutdown of machine (aka power cord
unplug), we booted into our bootloader in Power, which is a Linux kernel,
and kexec'ed into another distro. If this kexec is too quick, we end up
reaching the probe of NVMe adapter in that distro when adapter is in
bad state (not fully initialized on our bootloader). What happens next
is that nvme_wait_ready() is unable to complete, except if the quirk is
enabled.
So, this patch removes the original ctrl->tagset verification in order
to enable the quirk even on probe time.
Fixes: 54adc01055b7 ("nvme/quirk: Add a delay before checking for adapter readiness")
Reported-by: Andrew Byrne <byrneadw@ie.ibm.com>
Reported-by: Jaime A. H. Gomez <jahgomez@mx1.ibm.com>
Reported-by: Zachary D. Myers <zdmyers@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jeffrey Lien <Jeff.Lien@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
command-line option
commit dd853fd216d1485ed3045ff772079cc8689a9a4a upstream.
A negative number can be specified in the cmdline which will be used as
setup_clear_cpu_cap() argument. With that we can clear/set some bit in
memory predceeding boot_cpu_data/cpu_caps_cleared which may cause kernel
to misbehave. This patch adds lower bound check to setup_disablecpuid().
Boris Petkov reproduced a crash:
[ 1.234575] BUG: unable to handle kernel paging request at ffffffff858bd540
[ 1.236535] IP: memcpy_erms+0x6/0x10
Signed-off-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: andi.kleen@intel.com
Cc: bp@alien8.de
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: slaoub@gmail.com
Fixes: ac72e7888a61 ("x86: add generic clearcpuid=... option")
Link: http://lkml.kernel.org/r/1482933340-11857-1-git-send-email-lukasz.odzioba@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 701dc207bf551d9fe6defa36e84a911e880398c3 upstream.
On AMD's SB800 and upwards, the SMBus is shared with the Integrated
Micro Controller (IMC).
The platform provides a hardware semaphore to avoid race conditions
among them. (Check page 288 of the SB800-Series Southbridges Register
Reference Guide http://support.amd.com/TechDocs/45482.pdf)
Without this patch, many access to the SMBus end with an invalid
transaction or even with the bus stalled.
Reported-by: Alexandre Desnoyers <alex@qtec.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>:
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e44fca5047054f1762813751626b5245e0da022 upstream.
Do not attempt to drain the health workqueue when unloading the device in
the recovery flow, this can cause a deadlock when the recovery work
tries to cancel itself with sync.
Because the work is no longer unconditionally canceled when unloading, it
must be explicitly canceled in the AER flow.
fixes: 689a248df83b ("net/mlx5: Cancel recovery work in remove flow")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 030ee7ae52a46a2be52ccc8242c4a330aba8d38e upstream.
The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.
Also make sure that the signals are asserted only when changing speed
from B0.
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7192c54a68013f6058b1bb505645fcd07015191c upstream.
Port of radeon change to amdgpu.
Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5165484b02f2cbedb5bf3a41ff5e8ae16069016c upstream.
Use the appropriate smc firmware for each chip revision.
Using the wrong one can cause stability issues.
Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a08403bcb39f5d0e733bcf59a8a74f16b538f6e upstream.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=98897
https://bugs.launchpad.net/bugs/1651981
Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Adrian Fiergolski <A.Fiergolski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6458bd4dfd9414cba5804eb9907fe2a824278c34 upstream.
Use the appropriate smc firmware for each chip revision.
Using the wrong one can cause stability issues.
Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aebe55c2d4b998741c0847ace1b4af47d73c763b upstream.
If waiting for fences fails for blocking commits, planes must be cleaned
up before returning.
Fixes: f6ce410a59a4 ("drm/fence: allow fence waiting to be interrupted by userspace")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170102231427.7192-1-laurent.pinchart@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The backport of
2c7d0602c - "Fix PCODE polling during CDCLK change notification"
to the 4.9 stable tree used an incorrect timeout value. Fix this up
so the backport matches the upstream commit.
Reported-by: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc5367bcc556e97555fc94a32cd1aadbebdff47e upstream.
With commit e53743994e21
("af_iucv: use paged SKBs for big outbound messages"),
we transmit paged skbs for both of AF_IUCV's transport modes
(IUCV or HiperSockets).
The qeth driver for Layer 3 HiperSockets currently doesn't
support NETIF_F_SG, so these skbs would just be linearized again
by the stack.
Avoid that overhead by using paged skbs only for IUCV transport.
cc stable, since this also circumvents a significant skb leak when
sending large messages (where the skb then needs to be linearized).
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Fixes: e53743994e21 ("af_iucv: use paged SKBs for big outbound messages")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93362fa47fe98b62e4a34ab408c4a418432e7939 upstream.
Fixes CVE-2016-9191, proc_sys_readdir doesn't drop reference
added by grab_header when return from !dir_emit_dots path.
It can cause any path called unregister_sysctl_table will
wait forever.
The calltrace of CVE-2016-9191:
[ 5535.960522] Call Trace:
[ 5535.963265] [<ffffffff817cdaaf>] schedule+0x3f/0xa0
[ 5535.968817] [<ffffffff817d33fb>] schedule_timeout+0x3db/0x6f0
[ 5535.975346] [<ffffffff817cf055>] ? wait_for_completion+0x45/0x130
[ 5535.982256] [<ffffffff817cf0d3>] wait_for_completion+0xc3/0x130
[ 5535.988972] [<ffffffff810d1fd0>] ? wake_up_q+0x80/0x80
[ 5535.994804] [<ffffffff8130de64>] drop_sysctl_table+0xc4/0xe0
[ 5536.001227] [<ffffffff8130de17>] drop_sysctl_table+0x77/0xe0
[ 5536.007648] [<ffffffff8130decd>] unregister_sysctl_table+0x4d/0xa0
[ 5536.014654] [<ffffffff8130deff>] unregister_sysctl_table+0x7f/0xa0
[ 5536.021657] [<ffffffff810f57f5>] unregister_sched_domain_sysctl+0x15/0x40
[ 5536.029344] [<ffffffff810d7704>] partition_sched_domains+0x44/0x450
[ 5536.036447] [<ffffffff817d0761>] ? __mutex_unlock_slowpath+0x111/0x1f0
[ 5536.043844] [<ffffffff81167684>] rebuild_sched_domains_locked+0x64/0xb0
[ 5536.051336] [<ffffffff8116789d>] update_flag+0x11d/0x210
[ 5536.057373] [<ffffffff817cf61f>] ? mutex_lock_nested+0x2df/0x450
[ 5536.064186] [<ffffffff81167acb>] ? cpuset_css_offline+0x1b/0x60
[ 5536.070899] [<ffffffff810fce3d>] ? trace_hardirqs_on+0xd/0x10
[ 5536.077420] [<ffffffff817cf61f>] ? mutex_lock_nested+0x2df/0x450
[ 5536.084234] [<ffffffff8115a9f5>] ? css_killed_work_fn+0x25/0x220
[ 5536.091049] [<ffffffff81167ae5>] cpuset_css_offline+0x35/0x60
[ 5536.097571] [<ffffffff8115aa2c>] css_killed_work_fn+0x5c/0x220
[ 5536.104207] [<ffffffff810bc83f>] process_one_work+0x1df/0x710
[ 5536.110736] [<ffffffff810bc7c0>] ? process_one_work+0x160/0x710
[ 5536.117461] [<ffffffff810bce9b>] worker_thread+0x12b/0x4a0
[ 5536.123697] [<ffffffff810bcd70>] ? process_one_work+0x710/0x710
[ 5536.130426] [<ffffffff810c3f7e>] kthread+0xfe/0x120
[ 5536.135991] [<ffffffff817d4baf>] ret_from_fork+0x1f/0x40
[ 5536.142041] [<ffffffff810c3e80>] ? kthread_create_on_node+0x230/0x230
One cgroup maintainer mentioned that "cgroup is trying to offline
a cpuset css, which takes place under cgroup_mutex. The offlining
ends up trying to drain active usages of a sysctl table which apprently
is not happening."
The real reason is that proc_sys_readdir doesn't drop reference added
by grab_header when return from !dir_emit_dots path. So this cpuset
offline path will wait here forever.
See here for details: http://www.openwall.com/lists/oss-security/2016/11/04/13
Fixes: f0c3b5093add ("[readdir] convert procfs")
Reported-by: CAI Qian <caiqian@redhat.com>
Tested-by: Yang Shukui <yangshukui@huawei.com>
Signed-off-by: Zhou Chengming <zhouchengming1@huawei.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Greg Kroah-Hartman
Niklas Söderlund
Huang Shijie
Russell Currey
Johan Hovold
Suraj Jitindar Singh
Gabriel Krisman Bertazi
Andrew F. Davis
Tony Lindgren
Wei Yongjun
Jacob Pan
Prarit Bhargava
Tejun Heo
Tobias Klauser
Dan Carpenter
Charles Keepax
Denis Kirjanov
Paul Mackerras
Bjorn Andersson
Chris Wilson
Ville Syrjälä
Chen-Yu Tsai
Arnd Bergmann
Imre Deak
Russell King
NeilBrown
Trond Myklebust
Neil Armstrong
Jeff Mahoney
Guilherme G. Piccoli
Lukasz Odzioba
Ricardo Ribalda Delgado
Daniel Jurgens
Alex Deucher
Flora Cui
Laurent Pinchart
Julian Wiedmann
Zhou Chengming