| Age | Commit message (Collapse) | Author |
|---|
|
commit 4e841d3eb9294ce4137fdb5d0a88f1bceab9c212 upstream.
When PCIe FLR support was added, much of the remove/release code for
PCIe was migrated to ->down_dev(), but ->down_dev() is never called for
device removal. Let's refactor the cleanup to be done in both cases.
Also, drop the comments above mwifiex_cleanup_pcie(), because they were
clearly wrong, and it's better to have clear and obvious code than to
detail the code steps in comments anyway.
Fixes: 4c5dae59d2e9 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac8616e4c81dded650dfade49a7da283565d37ce upstream.
The MP style clocks support an mux with pre-dividers. While the driver
correctly accounted for them in the .determine_rate callback, it did
not in the .recalc_rate and .set_rate callbacks.
This means when calculating the factors in the .set_rate callback, they
would be off by a factor of the active pre-divider. Same goes for
reading back the clock rate after it is set.
Fixes: 2ab836db5097 ("clk: sunxi-ng: Add M-P factor clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ad0bb39fce319d7b92c17d306ed0a9f70a02e7d upstream.
The enable bit offset for the hdmi-ddc module clock is wrong. It is
pointing to the main hdmi module clock enable bit.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8fa6 ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c75704ebcac2ffa31ee7bcc359baf701b52bf00 upstream.
After commit e9afc746299d ("hwrng: geode - Use linux/io.h instead of
asm/io.h") the geode-rng driver uses devres with pci_dev->dev to keep
track of resources, but does not actually register a PCI driver. This
results in the following issues:
1. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the geode-rng
driver will never do. As a result,
2. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by e9afc746299d ("hwrng: geode - Use linux/io.h
instead of asm/io.h").
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 6e9b5e76882c ("hwrng: geode - Migrate to managed API")
Cc: Matt Mackall <mpm@selenic.com>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69db7009318758769d625b023402161c750f7876 upstream.
After commit 31b2a73c9c5f ("hwrng: amd - Migrate to managed API"), the
amd-rng driver uses devres with pci_dev->dev to keep track of resources,
but does not actually register a PCI driver. This results in the
following issues:
1. The message
WARNING: CPU: 2 PID: 621 at drivers/base/dd.c:349 driver_probe_device+0x38c
is output when the i2c_amd756 driver loads and attempts to register a PCI
driver. The PCI & device subsystems assume that no resources have been
registered for the device, and the WARN_ON() triggers since amd-rng has
already do so.
2. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the amd-rng
driver will never do. As a result,
3. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by 31b2a73c9c5f ("hwrng: amd - Migrate to managed
API").
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 31b2a73c9c5f ("hwrng: amd - Migrate to managed API").
Cc: Matt Mackall <mpm@selenic.com>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 027fb89e61054b4aedd962adb3e2003dec78a716 upstream.
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e2ebfb2142acefecc2496e71360f50d25726040b upstream.
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16681037e75ce08f2980ac5dbb03414429c7a55d upstream.
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d11ad ("mmc: arasan: Add driver for Arasan SDHCI")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ce0c7b65505e0d915e99389cced45b478dc935d upstream.
The SDHCI controller in the SAMA5D2 chip requires a valid voltage set
in the power control register, otherwise commands will fail with a
timeout error.
When using the regulator framework to specify the regulator used by the
mmc device, the voltage is not configured, and it is not possible to use
the connected device.
Implement a custom 'set_power' function for this specific hardware, that
configures the voltage in the register in all cases.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b52330bbfe63b3305765354d6046c9f7f89c011 upstream.
What started as a rather straightforward race condition reported by
Dmitry using the syzkaller fuzzer ended up revealing some major
problems with how the audit subsystem managed its netlink sockets and
its connection with the userspace audit daemon. Fixing this properly
had quite the cascading effect and what we are left with is this rather
large and complicated patch. My initial goal was to try and decompose
this patch into multiple smaller patches, but the way these changes
are intertwined makes it difficult to split these changes into
meaningful pieces that don't break or somehow make things worse for
the intermediate states.
The patch makes a number of changes, but the most significant are
highlighted below:
* The auditd tracking variables, e.g. audit_sock, are now gone and
replaced by a RCU/spin_lock protected variable auditd_conn which is
a structure containing all of the auditd tracking information.
* We no longer track the auditd sock directly, instead we track it
via the network namespace in which it resides and we use the audit
socket associated with that namespace. In spirit, this is what the
code was trying to do prior to this patch (at least I think that is
what the original authors intended), but it was done rather poorly
and added a layer of obfuscation that only masked the underlying
problems.
* Big backlog queue cleanup, again. In v4.10 we made some pretty big
changes to how the audit backlog queues work, here we haven't changed
the queue design so much as cleaned up the implementation. Brought
about by the locking changes, we've simplified kauditd_thread() quite
a bit by consolidating the queue handling into a new helper function,
kauditd_send_queue(), which allows us to eliminate a lot of very
similar code and makes the looping logic in kauditd_thread() clearer.
* All netlink messages sent to auditd are now sent via
auditd_send_unicast_skb(). Other than just making sense, this makes
the lock handling easier.
* Change the audit_log_start() sleep behavior so that we never sleep
on auditd events (unchanged) or if the caller is holding the
audit_cmd_mutex (changed). Previously we didn't sleep if the caller
was auditd or if the message type fell between a certain range; the
type check was a poor effort of doing what the cmd_mutex check now
does. Richard Guy Briggs originally proposed not sleeping the
cmd_mutex owner several years ago but his patch wasn't acceptable
at the time. At least the idea lives on here.
* A problem with the lost record counter has been resolved. Steve
Grubb and I both happened to notice this problem and according to
some quick testing by Steve, this problem goes back quite some time.
It's largely a harmless problem, although it may have left some
careful sysadmins quite puzzled.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d98ce0be541d4a3cfbb52cd75072c0339ebb500 upstream.
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117ba ("powerpc/kvm: make hypervisor state restore a function")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dac7a4b4b1f664934e8b713f529b629f67db313c upstream.
We must lock the xattr block before calculating or verifying the
checksum in order to avoid spurious checksum failures.
https://bugzilla.kernel.org/show_bug.cgi?id=193661
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9cf625d6ecde0d372e23ae022feead72b4228a6 upstream.
If ext4_convert_inline_data() was called on a directory with inline
data, the filesystem was left in an inconsistent state (as considered by
e2fsck) because the file size was not increased to cover the new block.
This happened because the inode was not marked dirty after i_disksize
was updated. Fix this by marking the inode dirty at the end of
ext4_finish_convert_inline_dir().
This bug was probably not noticed before because most users mark the
inode dirty afterwards for other reasons. But if userspace executed
FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by
'kvm-xfstests -c adv generic/396', then the inode was never marked dirty
after updating i_disksize.
Fixes: 3c47d54170b6a678875566b1b8d6dcf57904e49b
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a69645dde1188723d80745c1bc6ee9af2cbe2a7 upstream.
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a big warning like:
"sysfs: cannot create duplicate filename '/devices/parport0/ppdev0.0'".
And with that many parallel port printers stopped working.
We have been using the minor number as the id field while registering
a parralel port device with a parralel port. But when there are
multiple parrallel port device for one single parallel port, they all
tried to register with the same name like 'pardev0.0' and everything
started failing.
Use an incremented index as the id instead of the minor number.
Fixes: 8b7d3a9d903e ("ppdev: use new parport device model")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322
Tested-by: James Feeney <james@nurealm.net>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03270c6ac6207fc55bbf9d20d195029dca210c79 upstream.
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a nice warning like:
"sysctl table check failed:
/dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists"
Use the same logic as used in parport_register_device() and register
the proc files only once for each parallel port.
Fixes: 6fa45a226897 ("parport: add device-model to parport subsystem")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322
Tested-by: James Feeney <james@nurealm.net>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c6240cacdb2c3cb56a21fb3ea0c105154ab87a2a upstream.
The driver still struggles with firmwares that do not replay to the OS
version request. It is safe not waiting for the replay. First, the driver
doesn't do anything with the replay second the connection is closed
immediately, hence the packet will be just safely discarded in case it
is received and last the driver won't get stuck if the firmware won't
reply.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a733ded50b6ea846200073e7381a302df71e13b3 upstream.
This patch fixes 'mei: synchronize irq before initiating a reset'
The patch had introduced a deadlock between irq thread and mei_reset()
as they are both holding the same device lock.
---> device_lock:
mei_reset()
<---- interrupt thread
device_lock
---> synchornize_irq()
wait on interrupt thread == (dead lock)
The fix is to call synchronize_irq
prior to call locked mei_reset function.
Fixes: f302bb0de6ac (mei: synchronize irq before initiating a reset)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3ff861f59f6c1f5bf2bc03d2cd36ac3f992cbc06 upstream.
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sensor properties losing after resume from S3
commit 3bec247474469f769af41e8c80d3a100dd97dd76 upstream.
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c42f8218610aa09d7d3795e5810387673c1f84b6 upstream.
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software device creation will result in undefined
behaviour when configfs is built as a module since the configfs group for
the device not properly initialized.
Similar to commit b2f0c09664b7 ("iio: sw-trigger: Fix config group
initialization").
Fixes: 0f3a8c3f34f7 ("iio: Add support for creating IIO devices via configfs")
Reported-by: Miguel Robles <miguel.robles@farole.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e83bb3e6f3efa21f4a9d883a25d0ecd9dfb431e1 upstream.
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805f7a ("iio: ti_am335x_adc: Add continuous sampling support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 773dc118756b1f38766063e90e582016be868f09 upstream.
HS400-ES devices fail to initialize with the following error messages.
mmc1: power class selection to bus width 8 ddr 0 failed
mmc1: error -110 whilst initialising MMC card
This was seen on Samsung Chromebook Plus. Code analysis points to
commit 3d4ef329757c ("mmc: core: fix multi-bit bus width without
high-speed mode"), which attempts to set the bus width for all but
HS200 devices unconditionally. However, for HS400-ES, the bus width
is already selected.
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Fixes: 3d4ef329757c ("mmc: core: fix multi-bit bus width ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea90e0dc8cecba6359b481e24d9c37160f6f524f upstream.
Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out
to be perfectly accurate - there are various error paths that miss unlock
of the RTNL.
To fix those, change the locking a bit to not be conditional in all those
nl80211_prepare_*_dump() functions, but make those require the RTNL to
start with, and fix the buggy error paths. This also let me use sparse
(by appropriately overriding the rtnl_lock/rtnl_unlock functions) to
validate the changes.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 181302dc7239add8ab1449c23ecab193f52ee6ab upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 53f3a9e26ed5 ("mmc: USB SD Host Controller (USHC) driver")
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit daf229b15907fbfdb6ee183aac8ca428cb57e361 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Note that the dereference happens in the start callback which is called
during probe.
Fixes: de520b8bd552 ("uwb: add HWA radio controller driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ce362711d78a4999011add3115b8f4b0bc25e8c upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Note that the dereference happens in the cmd and wait_init_done
callbacks which are called during probe.
Fixes: 1ba47da52712 ("uwb: add the i1480 DFU driver")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e47c53503eb9faff42b3cfa144a833344dd1f89 upstream.
Make sure to initialise the return value to avoid having allocation
failures going unnoticed when allocating interrupt-endpoint resources.
This prevents use-after-free or worse when the device is later unbound.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Cc: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 687e0687f71ec00e0132a21fef802dee88c2f1ad upstream.
USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.
Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.
Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Fixes: 5b775f672cc9 ("USB: add USB test and measurement class driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b2db29fbb4e766fcd02207eb2e2087170bd6ebc upstream.
If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.
usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10
[<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c
[<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298
[<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152]
[<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8
[<ffffffc000774a24>] driver_probe_device+0x180/0x3b4
[<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0
[<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4
[<ffffffc0007747ec>] __device_attach+0xd0/0x158
[<ffffffc000775080>] device_initial_probe+0x24/0x30
[<ffffffc0007739d4>] bus_probe_device+0x50/0xe4
[<ffffffc000770bd0>] device_add+0x414/0x738
[<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914
[<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.
Fixes: 890dae886721 ("xhci: Enable LPM support only for hardwired ...")
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0090114d336a9604aa2d90bc83f20f7cd121b76c upstream.
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03ace948a4eb89d1cf51c06afdfc41ebca5fdb27 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e31 ("wusb: add the Wire Adapter (WA) core")
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0addd3fa6bcd119be9428996d5d4522479ab240 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1dc56c52d2484be09c7398a5207d6b11a4256be9 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should the probed device lack endpoints.
Note that this driver does not bind to any devices by default.
Fixes: ce21bfe603b3 ("USB: Add LVS Test device driver")
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f259ca3eed6e4b79ac3d5c5c9fb259fb46e86217 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3243367b209faed5c320a4e5f9a565ee2a2ba958 upstream.
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67b0503db9c29b04eadfeede6bebbfe5ddad94ef upstream.
The buffer allocation for the firmware data was changed in
commit 43fab9793c1f ("[media] dvb-usb: don't use stack for firmware load")
but the same applies for the reset value.
Fixes: 43fab9793c1f ("[media] dvb-usb: don't use stack for firmware load")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09424c50b7dff40cb30011c09114404a4656e023 upstream.
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cdd7928df0d2efaa3270d711963773a08a4cc8ab upstream.
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 436ecf5519d892397af133a79ccd38a17c25fa51 upstream.
This is a Dell branded Sierra Wireless EM7455.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e9f44eaaef0df7b846e9316fa9ca72a02025d44 upstream.
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f307834e695f59dac4337a40316bdecfb9d0508 upstream.
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f363a06642f28caaa78cb6446bbad90c73fe183c upstream.
In the commit [15c75b09f8d1: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK). This patch fixes that obvious bug.
(As a side note: although the original commit was completely wrong,
it's still working for most of machines, as it sets to 32bit DMA mask
in the end. So the bug severity is low.)
Fixes: 15c75b09f8d1 ("ALSA: ctxfi: Fallback DMA mask to 32bit")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c520ff3d03f0b5db7146d9beed6373ad5d2a5e0e upstream.
When snd_seq_pool_done() is called, it marks the closing flag to
refuse the further cell insertions. But snd_seq_pool_done() itself
doesn't clear the cells but just waits until all cells are cleared by
the caller side. That is, it's racy, and this leads to the endless
stall as syzkaller spotted.
This patch addresses the racy by splitting the setup of pool->closing
flag out of snd_seq_pool_done(), and calling it properly before
snd_seq_pool_done().
BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.com
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 92461f5d723037530c1f36cce93640770037812c upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Fixes: bdb5c57f209c ("Input: add sur40 driver for Samsung SUR40... ")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb1b494663e037253337623bf1ef2df727883cb7 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac2ee9ba953afe88f7a673e1c0c839227b1d7891 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915e5 ("Input: add driver for USB VoIP phones with CM109...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5cc4a1a9f5c179795c8a1f2b0f4361829d6a070e upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: aca951a22a1d ("[PATCH] input-driver-yealink-P1K-usb-phone")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba340d7b83703768ce566f53f857543359aa1b98 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: bba5394ad3bd ("Input: add support for Hanwang tablets")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1916d319271664241b7aa0cd2b05e32bdb310ce9 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack control-interface endpoints.
Fixes: 628329d52474 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59cf8bed44a79ec42303151dd014fdb6434254bb upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Brian Norris
Chen-Yu Tsai
Prarit Bhargava
Adrian Hunter
Anssi Hannula
Romain Izard
Paul Moore
Nicholas Piggin
Theodore Ts'o
Eric Biggers
Sudip Mukherjee
Alexander Usyskin
Tomas Winkler
Dmitry Torokhov
Song Hongyan
Lars-Peter Clausen
Michael Engl
Guenter Roeck
Johannes Berg
Johan Hovold
Bin Liu
Samuel Thibault
Stefan Brüns
Roger Quadros
Oliver Neukum
Bjørn Mork
Dan Williams
Hui Wang
Takashi Iwai