diff options
Diffstat (limited to 'Documentation/devicetree')
11 files changed, 151 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/arm/armada-38x.txt b/Documentation/devicetree/bindings/arm/armada-38x.txt index 11f2330a6554..ad9f8ed4d9bd 100644 --- a/Documentation/devicetree/bindings/arm/armada-38x.txt +++ b/Documentation/devicetree/bindings/arm/armada-38x.txt @@ -6,5 +6,15 @@ following property: Required root node property: - - compatible: must contain either "marvell,armada380" or - "marvell,armada385" depending on the variant of the SoC being used. + - compatible: must contain "marvell,armada380" + +In addition, boards using the Marvell Armada 385 SoC shall have the +following property before the previous one: + +Required root node property: + +compatible: must contain "marvell,armada385" + +Example: + +compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada380"; diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 5216b419016a..8b4f7b7fe88b 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -9,6 +9,18 @@ Required Properties: - reg: physical base address of the controller and length of memory mapped region. +Optional Properties: +- clocks: List of clock handles. The parent clocks of the input clocks to the + devices in this power domain are set to oscclk before power gating + and restored back after powering on a domain. This is required for + all domains which are powered on and off and not required for unused + domains. +- clock-names: The following clocks can be specified: + - oscclk: Oscillator clock. + - pclkN, clkN: Pairs of parent of input clock and input clock to the + devices in this power domain. Maximum of 4 pairs (N = 0 to 3) + are supported currently. + Node of a device using power domains must have a samsung,power-domain property defined with a phandle to respective power domain. @@ -19,6 +31,14 @@ Example: reg = <0x10023C00 0x10>; }; + mfc_pd: power-domain@10044060 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10044060 0x20>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_SW_ACLK333>, + <&clock CLK_MOUT_USER_ACLK333>; + clock-names = "oscclk", "pclk0", "clk0"; + }; + Example of the node using power domain: node { diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index b513cb8196fe..af527ee111c2 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -40,6 +40,9 @@ Optional properties: - arm,filter-ranges : <start length> Starting address and length of window to filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. +- arm,io-coherent : indicates that the system is operating in an hardware + I/O coherent mode. Valid only when the arm,pl310-cache compatible + string is used. - interrupts : 1 combined interrupt. - cache-id-part: cache id part number to be used if it is not present on hardware diff --git a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt index 5d49f2b37f68..832fe8cc24d7 100644 --- a/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt +++ b/Documentation/devicetree/bindings/arm/samsung/exynos-adc.txt @@ -48,7 +48,7 @@ adc@12D10000 { /* NTC thermistor is a hwmon device */ ncp15wb473@0 { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <47000>; pulldown-ohm = <0>; diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt index f055515d2b62..366690cb86a3 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-cpu0.txt @@ -8,10 +8,12 @@ Both required and optional properties listed below must be defined under node /cpus/cpu@0. Required properties: -- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt - for details +- None Optional properties: +- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt for + details. OPPs *must* be supplied either via DT, i.e. this property, or + populated at runtime. - clock-latency: Specify the possible maximum transition latency for clock, in unit of nanoseconds. - voltage-tolerance: Specify the CPU voltage tolerance in percentage. diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index c6f66674f19c..b117b2e9e1a7 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -3,11 +3,19 @@ NTC Thermistor hwmon sensors Requires node properties: - "compatible" value : one of - "ntc,ncp15wb473" - "ntc,ncp18wb473" - "ntc,ncp21wb473" - "ntc,ncp03wb473" - "ntc,ncp15wl333" + "murata,ncp15wb473" + "murata,ncp18wb473" + "murata,ncp21wb473" + "murata,ncp03wb473" + "murata,ncp15wl333" + +/* Usage of vendor name "ntc" is deprecated */ +<DEPRECATED> "ntc,ncp15wb473" +<DEPRECATED> "ntc,ncp18wb473" +<DEPRECATED> "ntc,ncp21wb473" +<DEPRECATED> "ntc,ncp03wb473" +<DEPRECATED> "ntc,ncp15wl333" + - "pullup-uv" Pull up voltage in micro volts - "pullup-ohm" Pull up resistor value in ohms - "pulldown-ohm" Pull down resistor value in ohms @@ -21,7 +29,7 @@ Read more about iio bindings at Example: ncp15wb473@0 { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <47000>; pulldown-ohm = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt new file mode 100644 index 000000000000..dde6c22ce91a --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -0,0 +1,42 @@ +* Rockchip RK3xxx I2C controller + +This driver interfaces with the native I2C controller present in Rockchip +RK3xxx SoCs. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or + "rockchip,rk3288-i2c". + - interrupts : interrupt number + - clocks : parent clock + +Required on RK3066, RK3188 : + + - rockchip,grf : the phandle of the syscon node for the general register + file (GRF) + - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF) + is also required. + +Optional properties : + + - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used. + +Example: + +aliases { + i2c0 = &i2c0; +} + +i2c0: i2c@2002d000 { + compatible = "rockchip,rk3188-i2c"; + reg = <0x2002d000 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + rockchip,grf = <&grf>; + + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt new file mode 100644 index 000000000000..6b765485af7d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt @@ -0,0 +1,41 @@ + +* Allwinner P2WI (Push/Pull 2 Wire Interface) controller + +Required properties : + + - reg : Offset and length of the register set for the device. + - compatible : Should one of the following: + - "allwinner,sun6i-a31-p2wi" + - interrupts : The interrupt line connected to the P2WI peripheral. + - clocks : The gate clk connected to the P2WI peripheral. + - resets : The reset line connected to the P2WI peripheral. + +Optional properties : + + - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the +default frequency is 100kHz + +A P2WI may contain one child node encoding a P2WI slave device. + +Slave device properties: + Required properties: + - reg : the I2C slave address used during the initialization + process to switch from I2C to P2WI mode + +Example: + + p2wi@01f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <6000000>; + resets = <&apb0_rst 3>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 64fd7dec1bbc..b3556609a06f 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -4,6 +4,13 @@ Required properties: - compatible: Must contain one of the following: + - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. + - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. + - "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART. + - "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART. + - "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART. + - "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART. + - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt index b82a268f1bd4..bee6ff204baf 100644 --- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt @@ -23,6 +23,12 @@ Optional properties: - spi-max-frequency: Specifies maximum SPI clock frequency, Units - Hz. Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt +- num-cs: total number of chipselects +- cs-gpios: should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child + nodes. If unspecified, a single SPI device without a chip + select can be used. + SPI slave nodes must be children of the SPI master node and can contain properties described in Documentation/devicetree/bindings/spi/spi-bus.txt diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 4d7f3758d1b4..46a311e728a8 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -83,6 +83,7 @@ mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG mundoreader Mundo Reader S.L. +murata Murata Manufacturing Co., Ltd. mxicy Macronix International Co., Ltd. national National Semiconductor neonode Neonode Inc. |