diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
10 files changed, 51 insertions, 34 deletions
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt index b6a7e7397b8b..b944fe067188 100644 --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt @@ -16,6 +16,9 @@ Required properties: Documentation/devicetree/bindings/graph.txt. This port should be connected to the input port of an attached HDMI or LVDS encoder chip. +Optional properties: +- pinctrl-names: Contain "default" and "sleep". + Example: dpi0: dpi@1401d000 { @@ -26,6 +29,9 @@ dpi0: dpi@1401d000 { <&mmsys CLK_MM_DPI_ENGINE>, <&apmixedsys CLK_APMIXED_TVDPLL>; clock-names = "pixel", "engine", "pll"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dpi_pin_func>; + pinctrl-1 = <&dpi_pin_idle>; port { dpi0_out: endpoint { diff --git a/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt b/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt index c82794002595..89647d714387 100644 --- a/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt +++ b/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt @@ -21,7 +21,7 @@ controller state. The mux controller state is described in Example: mux: mux-controller { - compatible = "mux-gpio"; + compatible = "gpio-mux"; #mux-control-cells = <0>; mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index dd559045593d..d2d1bae63a36 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -123,7 +123,7 @@ on various other factors also like; so the device should have enough free bytes available its OOB/Spare area to accommodate ECC for entire page. In general following expression helps in determining if given device can accommodate ECC syndrome: - "2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE" + "2 + (PAGESIZE / 512) * ECC_BYTES" <= OOBSIZE" where OOBSIZE number of bytes in OOB/spare area PAGESIZE number of bytes in main-area of device page diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt index 9c5e663fa1af..828a04695e1b 100644 --- a/Documentation/devicetree/bindings/net/btusb.txt +++ b/Documentation/devicetree/bindings/net/btusb.txt @@ -36,7 +36,7 @@ Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt: compatible = "usb1286,204e"; reg = <1>; interrupt-parent = <&gpio0>; - interrupt-name = "wakeup"; + interrupt-names = "wakeup"; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt index 92486733df71..8ebc5200032a 100644 --- a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt +++ b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt @@ -26,7 +26,7 @@ Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2): clock-frequency = <100000>; interrupt-parent = <&gpio1>; - interrupts = <29 GPIO_ACTIVE_HIGH>; + interrupts = <29 IRQ_TYPE_LEVEL_HIGH>; enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt index 538a86f7b2b0..982d4dd4eba3 100644 --- a/Documentation/devicetree/bindings/net/nfc/pn544.txt +++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt @@ -26,7 +26,7 @@ Example (for ARM-based BeagleBone with PN544 on I2C2): clock-frequency = <400000>; interrupt-parent = <&gpio1>; - interrupts = <17 GPIO_ACTIVE_HIGH>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt index f64060908d5a..35f469c4f675 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt @@ -43,26 +43,26 @@ group emmc_nb group pwm0 - pin 11 (GPIO1-11) - - functions pwm, gpio + - functions pwm, led, gpio group pwm1 - pin 12 - - functions pwm, gpio + - functions pwm, led, gpio group pwm2 - pin 13 - - functions pwm, gpio + - functions pwm, led, gpio group pwm3 - pin 14 - - functions pwm, gpio + - functions pwm, led, gpio group pmic1 - - pin 17 + - pin 7 - functions pmic, gpio group pmic0 - - pin 16 + - pin 6 - functions pmic, gpio group i2c2 @@ -112,17 +112,25 @@ group usb2_drvvbus1 - functions drvbus, gpio group sdio_sb - - pins 60-64 + - pins 60-65 - functions sdio, gpio group rgmii - - pins 42-55 + - pins 42-53 - functions mii, gpio group pcie1 - - pins 39-40 + - pins 39 + - functions pcie, gpio + +group pcie1_clkreq + - pins 40 - functions pcie, gpio +group smi + - pins 54-55 + - functions smi, gpio + group ptp - pins 56-58 - functions ptp, gpio diff --git a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt index 093edda0c8df..6cd83d920155 100644 --- a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt +++ b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt @@ -13,6 +13,14 @@ common regulator binding documented in: Required properties of the main device node (the parent!): + - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + + [1] If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties of the main device node (the parent!): - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) units for buck2 when changing voltage using gpio dvs. Refer to [1] below for additional information. @@ -25,26 +33,13 @@ Required properties of the main device node (the parent!): units for buck4 when changing voltage using gpio dvs. Refer to [1] below for additional information. - - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used - for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. - - [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' - property should specify atleast one voltage level (which would be a - safe operating voltage). - - If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, then all the eight voltage values for the - 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. - -Optional properties of the main device node (the parent!): - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. Additional properties required if either of the optional properties are used: - - s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from + - s5m8767,pmic-buck-default-dvs-idx: Default voltage setting selected from the possible 8 options selectable by the dvs gpios. The value of this property should be between 0 and 7. If not specified or if out of range, the default value of this property is set to 0. diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt index 68c4e8d96bed..b309de00cd83 100644 --- a/Documentation/devicetree/bindings/sound/wm8994.txt +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -14,9 +14,15 @@ Required properties: - #gpio-cells : Must be 2. The first cell is the pin number and the second cell is used to specify optional parameters (currently unused). - - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, - SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered - in Documentation/devicetree/bindings/regulator/regulator.txt + - power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt, depending + on compatible: + - for wlf,wm1811 and wlf,wm8958: + AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, + DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply + - for wlf,wm8994: + AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply, + SPKVDD1-supply, SPKVDD2-supply Optional properties: @@ -68,11 +74,11 @@ codec: wm8994@1a { lineout1-se; + AVDD1-supply = <®ulator>; AVDD2-supply = <®ulator>; CPVDD-supply = <®ulator>; - DBVDD1-supply = <®ulator>; - DBVDD2-supply = <®ulator>; - DBVDD3-supply = <®ulator>; + DBVDD-supply = <®ulator>; + DCVDD-supply = <®ulator>; SPKVDD1-supply = <®ulator>; SPKVDD2-supply = <®ulator>; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 44e8bab159ad..baee73134d03 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -47,6 +47,8 @@ Optional properties: from P0 to P1/P2/P3 without delay. - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check during HS transmit. + - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in + park mode are disabled. - snps,dis_metastability_quirk: when set, disable metastability workaround. CAUTION: use only if you are absolutely sure of it. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal |